Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 20
Encontrada(s) 1 página(s)

Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Super class AB RFC OTA with adaptive local common-mode feedback

  • Garde Luque, María Pilar
  • López Martín, Antonio
  • González Carvajal, Ramón
  • Ramírez-Angulo, Jaime
A super class AB recycling folded cascode operational transconductance amplifier is presented. It employs local common-mode feedback using two matched tuneable active resistors, allowing to adapt the amplifier to different process variations and loads. Measurement results from a test chip prototype fabricated in a 0.5 μm CMOS process validate the proposal., This work was funded by the Spanish Ministerio de Economía y Competitividad (Grant no. TEC2016-80396-C2-1-R (AEI/FEDER)).
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Wide-swing class AB regulated cascode current mirror

  • Garde Luque, María Pilar
  • López Martín, Antonio
  • Cruz Blas, Carlos Aristóteles de la
  • González Carvajal, Ramón
  • Ramírez-Angulo, Jaime
A micropower regulated cascode CMOS current mirror is presented, combining floating gate and quasi floating gate MOS transistors to achieve both wide swing and class AB operation, respectively. Measurement results for a 0.5 μm CMOS test chip prototype are included, showing that the current mirror can provide a THD at 100 kHz of -44 dB for a supply voltage of ±0.75 V and input current amplitudes 20 times larger than the bias current., This work has been supported in part by grant TEC2016-80396-C2 (AEI/FEDER).
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Low-power ultrasonic front-end for cargo container monitoring

  • Algueta-Miguel, Jose M.
  • García Oya, José Ramón
  • López Martín, Antonio
  • Cruz Blas, Carlos Aristóteles de la
  • Muñoz Chavero, Fernando
  • Hidalgo Fort, Eduardo
A low-power ultrasonic communication system conceived for cargo container monitoring is presented. Two piezoelectric transducers operating at 40 kHz are used for generating and acquiring an ultrasonic signal through the metallic wall, thus establishing a non-invasive inside-outside communication that preserves the container integrity. Both transducers are fixed by means of a novel magnetic case designed for optimizing data transmission. The acoustic and electrical characteristics of the ultrasonic channel are analyzed. An experimental measurement setup based on FPGA has been implemented for comparing some basic modulation and detection schemes in terms of Bit Error Rate (BER), also considering their robustness against undesired mechanical and electromagnetic perturbations. On this basis, a compact digital DBPSK modulator using a square carrier signal is proposed. Frequency and amplitude tracking algorithms are designed for optimizing the quality and robustness of the data transmission. Finally, a low-power low-rate (up to few kbps) architecture based on the previous elements is presented. All the proposed contributions are experimentally validated., This work was supported in part by Spanish Agencia Estatal de Investigación and Fondo Europeo de Desarrollo Regional under Grant TEC2016-80396-C2-1-R, and in part by the Obra Social La Caixa, Fundación Caja Navarra (Convocatoria 2018 de Captación de Talento).
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Tesis doctoral (DoctoralThesis)

Power-efficient CMOS circuits for energy harvesting supplied IoT systems

  • Garde Luque, María Pilar
En esta tesis se han aplicado técnicas de baja tensión y bajo consumo para implementar nuevos circuitos analógicos (principalmente amplificadores). Estos circuitos están orientados a dispositivos energéticamente autónomos como los utilizados en muchos escenarios del Internet de las Cosas (IoT). La estructura de la tesis es la siguiente: se proponen técnicas básicas para operación en baja tensión y bajo consumo, tanto a nivel de celda como a nivel de dispositivo, seguido por varios bloques básicos novedosos que utilizan dichas técnicas y finalmente por la obtención de nuevos diseños a nivel de subsistema. A nivel de celda, diferentes amplificadores energéticamente eficientes se proponen en este trabajo. Estos se obtienen combinando diferentes técnicas de baja tensión. Las principales son el uso de transistores de puerta cuasi-flotante (Quasi-Floating Gate o QFG) y algunas técnicas de polarización adaptativa, entre las que destacan el seguidor de tensión plegado (en inglés, Flipped Voltage Follower o FVF) y la realimentación local de modo común (Local Common-Mode Feedback o LCMFB). Estas técnicas pueden aplicarse tanto a amplificadores diferenciales como no diferenciales, creando así diferentes topologías. Los circuitos propuestos se comparan con otras publicaciones relevantes, mostrando un funcionamiento muy competitivo. A nivel de subsistema, otra técnica de baja tensión, basada en el uso de fuentes de tensión flotantes, se emplea para diseñar tres bloques, dos de los cuales están relacionados con la conversión analógico-digital (A/D). Los circuitos propuestos han sido fabricados usando diferentes tecnologías CMOS (130 nm, 180 nm y 0.5 μm) y los correspondientes resultados de las medidas son presentados y analizados para validar su funcionamiento. Además, se han realizado análisis teóricos para explorar el potencial de los circuitos y subsistemas resultantes en aplicaciones de bajo consumo y baja tensión., In this thesis, innovative low voltage and low power techniques have been applied to implement novel analog circuits (mainly amplifiers). These circuits are suitable for energy autonomous devices such as those required in many Internet of Things (IoT) scenarios. The structure of the thesis is as follows: basic techniques for low voltage low power operation are proposed, at both cell and device level, followed by several novel basic building blocks using them and finally the achievement of new designs at subsystem level. At circuit level, different power efficient amplifiers are proposed in this work. They are obtained by combining different low voltage techniques. The main ones are the use of Quasi-Floating Gate (QFG) transistors some adaptive biasing techniques (the Flipped Voltage Follower, or FVF, and the Local Common-Mode Feedback, or LCMFB, among others). These schemes can be applied to single-ended or to fully differential amplifiers, leading to different topologies. The proposed circuits are compared with other relevant publications, showing a very competitive performance. At subsystem level, another low voltage technique, which is based in the use of floating voltage sources, is employed to design three blocks, two of them related to A/D conversion. The proposed circuits have been fabricated using different CMOS technologies (130 nm, 180 nm and 0.5 μm) and the corresponding measurement results are provided and analyzed to validate their operation. In addition, theoretical analysis has been done to fully explore the potential of the resulting circuits and systems in the scenario of low-power low-voltage applications., Spanish Ministry of Economy and Competitiveness, through projects TEC2013-47286-C3-2, TEC2016-80396-C2-1-R and the short stays grants for researchers. Public University of Navarra, through its PhD. grant program., Programa de Doctorado en Tecnologías de las Comunicaciones, Bioingeniería y de las Energías Renovables (RD 99/2011), Bioingeniaritzako eta Komunikazioen eta Energia Berriztagarrien Teknologietako Doktoretza Programa (ED 99/2011)
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Energy harvesting approaches in IoT scenarios with very low ambient energy

  • López Martín, Antonio
  • Algueta-Miguel, Jose M.
  • Matías Maestro, Ignacio
Trabajo presentado a la International Conference on Renewable Energies and Power Quality (ICREPQ’19). Tenerife, 2019, The feasibility of multi-source energy harvesting in Internet of Things (IoT) scenarios with low and intermittent ambient energy is addressed. As a relevant case study, application to a smart cargo container system is analysed. The most relevant features of the main energy sources available in this target application are identified, and various transducers adapted to such sources are evaluated. Measurement results indicate that combined piezoelectric and thermoelectric generation inside cargo containers can significantly extend the battery lifetime of IoT end nodes embedded in such containers., This work was funded by Grant TEC2016-80396-C2-1-R (AEI/FEDER) and Obra Social La Caixa - Fundación Caja Navarra (Convocatoria 2018 de Captación de Talento).
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Pseudo-three-stage Miller op-amp with enhanced small-signal and large-signal performance

  • Paul, Anindita
  • Ramírez-Angulo, Jaime
  • López Martín, Antonio
  • González Carvajal, Ramón
  • Rocha-Pérez, José Miguel
A simple technique to implement highly power efficient class AB-AB Miller op-amps is presented in this paper. It uses a composite input stage with resistive local common mode feedback that provides class AB operation to the input stage and essentially enhances the op-amp's effective transconductance gain, the dc open-loop gain, the gain-bandwidth product, and slew rate with just moderate increase in power dissipation. The experimental results of op-amps in strong inversion and subthreshold fabricated in a 130-nm standard CMOS technology validate the proposed approach. The op-amp has 9 V·pF/μs·μW large-signal figure of merit (FOM) and 17 MHz · pF/μW small-signal FOM with 1.2-V supply voltage. In subthreshold, the op-amp has 10 V · pF/μs · μW large-signal FOM and 92 MHz · pF/μW small-signal FOM with 0.5-V supply voltage., This work was supported by Grant TEC2016-80396- C2-R (AEI/FEDER).
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Low-voltage 0.81mW, 1-32 CMOS VGA with 5% bandwidth variations and -38dB DC rejection

  • López Martín, Antonio
  • Rico-Aniles, Héctor Daniel
  • Ramírez-Angulo, Jaime
  • Rocha-Pérez, José Miguel
  • González Carvajal, Ramón
A CMOS low-voltage amplifier with approximately constant bandwidth and DC rejection is introduced. The design is based on the cascade of a wide linear input range OTA, an op-amp and a servo-loop with extremely large time constants. It operates with +/-0:45V supplies and a power consumption of 0.81mW in 180nm technology. The bandwidth changes only from 9.08MHz to 9.54MHz over a gain range from 1 to 32, it has a 9.8Hz low cutoff frequency and a DC attenuation of 38dBs. DC floating voltage sources are used to keep the gates of all differential pairs at a constant value close to a supply rail in order to operate the amplifier circuit with minimum supply voltage. The proposed circuit has small and large signal figures of merit FOMSS=5380 (MHz*pF/mW) and FOMLS=0:0085((V/ns)*pF/mA) for a nominal gain A=32., This work was supported by AEI/FEDER under Grant TEC2016-80396-C2. The work of Hector Daniel Rico-Aniles was supported by the Mexican Consejo Nacional de Ciencia y Tecnologia (CONACYT) for the Academic Scholarship under Grant 408946.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

On the optimal current followers for wide-swing current-efficient amplifiers

  • López Martín, Antonio
  • Garde Luque, María Pilar
  • González Carvajal, Ramón
  • Ramírez-Angulo, Jaime
2018 IEEE International Symposium on Circuits and Systems, ISCAS 2018 (27 May 2018 through 30 May 2018), The design of various current followers for the implementation of OTAs with high slew rate and current efficiency is addressed. Two basic current follower topologies are compared, and modifications of both followers to improve these parameters are presented. As an application example, an enhanced recycling folded cascode OTA is proposed. Measurement results of the OTA fabricated in a 0.5 μm CMOS process show a 260% and 180% improvement in SR and GBW, respectively, for the same power consumption., This work has been supported by the Spanish Ministerio de Economía y Competitividad, grant TEC2016-80396-C2-1-R.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

±0.25 V Class-AB CMOS capacitance multiplier and precision rectifiers

  • Pourashraf, Shirin
  • Ramírez-Angulo, Jaime
  • Hinojo Montero, José María
  • González Carvajal, Ramón
  • López Martín, Antonio
Reduction of minimum supply requirements is a crucial aspect to decrease the power consumption in VLSI systems. A high performance capacitance multiplier able to operate with supplies as low as ±0.25 V is presented. It is based on adaptively biased class-AB current mirrors which provide high current efficiency. Measurement results of a factor 11 capacitance multiplier fabricated in 180 nm CMOS technology verify theoretical claims. Moreover, low-voltage precision rectifiers based on the same class-AB current mirrors are designed and fabricated in the same CMOS process. They generate output currents over 100 times larger than the quiescent current. Both proposed circuits have 300 nW static power dissipation when operating with ±0.25 V supplies., This work was supported by the Spanish National Research Agency under Grant TEC2016-80396-C2 (AEI/FEDER)
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

CMOS first-order all-pass filter with 2-Hz pole frequency

  • Paul, Anindita
  • Ramírez-Angulo, Jaime
  • López Martín, Antonio
  • González Carvajal, Ramón
A CMOS fully integrated all-pass filter with an extremely low pole frequency of 2 Hz is introduced in this paper. It has 0.08-dB passband ripple and 0.029-mm2 Si area. It has 0.38-mW power consumption in strong inversion with ±0.6-V power supplies. In subthreshold, it has 0.64-uW quiescent power and operates with ±200-mV dc supplies. Miller multiplication is used to obtain a large equivalent capacitor without excessive Si area. By varying the gain of the Miller amplifier, the pole frequency can be varied from 2 to 48 Hz. Experimental and simulation results of a test chip prototype in 130-nm CMOS technology validate the proposed circuit., This work was supported by AEI/FEDER under Grant TEC2016-80396-C2.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Subsampling OFDM-based ultrasonic data communication through metallic channels for monitoring of cargo containers

  • García Oya, José Ramón
  • Algueta-Miguel, Jose M.
  • García Doblado, José
  • Muñoz Chavero, Fernando
  • Hidalgo Fort, Eduardo
  • Baena Lecuyer, Vicente
  • López Martín, Antonio
An enhanced ultrasonic communication system based on piezoelectric transducers for monitoring of goods in cargo containers is presented. The proposed system consists of several sensors placed inside the container, whose data are collected and transmitted outside it. Data transmission is carried out by an ultrasonic communication channel, in order to avoid drilling the wall of the container. The proposed data communication system is based on the transmission of a 128-OFDM signal. This modulation has been chosen due to its robustness to channels with frequency-selective fading and its spectrum efficiency. In order to increase the signal bandwidth and to reduce the power consumption at the internal node (transmitter), the proposed system exploits the non-linearity of the metallic channel to transmit at higher resonance frequencies. Moreover, power consumption at the external node (receiver) is reduced by using a subsampling based receiver, which allows its implementation by low-cost electronics., This work was supported by the Spanish Ministry of Economy and Competitiveness under Projects TEC2016-80396-C2-2-R and TEC2016-80396-C2-1-R
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Folded Cascode OTA with 5540 MHzpF/mA FoM

  • Garde Luque, María Pilar
  • López Martín, Antonio
  • González Carvajal, Ramón
  • Ramírez-Angulo, Jaime
2018 IEEE International Symposium on Circuits and Systems, ISCAS 2018 (27 May 2018 through 30 May 2018), A micropower single-stage folded cascode amplifier able to drive a wide range of capacitive loads is presented. It features class AB operation and includes power-efficient adaptive biasing techniques, which provide enhanced dynamic output current boosting and gain-bandwidth product (GBW). Phase lead compensation is used to improve phase margin and settling performance for low capacitive loads. Measurement results for a 0.5 μm CMOS process show a FoM of 5540 MHz pF/mA, the highest one reported to date for a folded cascode amplifier to the authors' knowledge., This work has been supported by the Spanish Ministerio de Economía y Competitividad, grant TEC2016-80396-C2-1-R.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

A highly efficient composite class-AB–AB Miller op-amp with high gain and stable from 15 pF up to very large capacitive loads

  • Pourashraf, Shirin
  • Ramírez-Angulo, Jaime
  • López Martín, Antonio
  • González Carvajal, Ramón
In this paper, a highly power-efficient class-AB–AB Miller op-amp is discussed. The structure uses gm enhancement based on local common-mode feedback to provide class-AB operation with enhanced effective gm , open-loop gain, unity-gain frequency, and slew rate ( SR ) without significant increase in quiescent power consumption. Utilization of a nonlinear load leads to large symmetric positive and negative SRs . Stability over an extremely wide range of capacitive loads is achieved through a combination of Miller and phase-lead compensations. The unity-gain frequency does not show sensitivity to capacitive load values. A test chip prototype fabricated in 0.18- μm CMOS technology shows 90.8-dB open-loop gain, 12.5-MHz bandwidth for a 25-pF load capacitance, and a factor 60 SR enhancement with maximum output current close to 1-mA and 43- μA total static current., This work was supported by the Spanish National Research Agency under Grant TEC2016-80396-C2.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Super-gain-boosted AB-AB fully differential Miller op-amp with 156dB open-loop gain and 174MV/V MHZ pF/uW figure of merit in 130nm CMOS technology

  • Paul, Anindita
  • Ramírez-Angulo, Jaime
  • Díaz Sánchez, Alejandro
  • López Martín, Antonio
  • González Carvajal, Ramón
  • Li, Frank X.
A fully differential Miller op-amp with a composite input stage using resistive local common-mode feedback and regulated cascode transistors is presented here. High gain pseudo-differential auxiliary amplifiers are used to implement the regulated cascode transistors in order to boost the output impedance of the composite input stage and the open-loop gain of the op-amp. Both input and output stages operate in class AB mode. The proposed op-amp has been simulated in a 130nm commercial CMOS process technology. It operates from a 1.2V supply and has a close to rail-to-rail differential output swing. It has 156dB DC open-loop gain and 63MHz gain-bandwidth product with a 30pF capacitive load. The op-amp has a DC open-loop gain figure of merit FOMAOLDC of 174 (MV/V) MHz pF/uW and large-signal figure of merit FOMLS of 3(V/us) pF/uW., This work was supported in part by the Spanish Government Agencia Estatal de Investigación (AEI) under Grant TEC2016-80396-C2, in part by the Consejería de Economía y Conocimiento of Junta de Andalucía under Grant P18-FR-4317 (both projects received support from the Fondo Europeo de Desarrollo Regional (FEDER)), and in part by the Consejo Nacional de Ciencia y Tecnologia (CONACyT) under Grant A1-S-43214.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

A 1.2-V current-mode RMS-to-DC converter based on a novel two-quadrant electronically simulated MOS translinear loop

  • Martincorena Arraiza, Maite
  • Cruz Blas, Carlos Aristóteles de la
  • Algueta-Miguel, Jose M.
  • López Martín, Antonio
A novel current-mode CMOS RMS-to-DC converter using translinear techniques is introduced. It is based on a squarer/divider cell that is implemented using an electronically simulated loop with a novel biasing scheme that allows its operation in two quadrants. The cell is designed using a differential input current and a small signal first order filter to implement the voltage averaging, leading to a compact solution that can be used with low voltage supplies. The converter has been fabricated in a standard 130-nm CMOS process, and measurement results are provided to demonstrate the feasibility of the system., This work was supported in part by Agencia Estatal de Investigación/Fondo Europeo de Desarrollo Regional under Grant TEC2016-80396-C2-1-R, and in part by the Obra Social La Caixa - Fundación Caja Navarra (Convocatoria 2018 de Captación de Talento).
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Super-gain-boosted miller op-amp based on nested regulated cascode techniques with FoMAOLDC =24,614kV/V.MHz.pF/µWatt

  • Paul, Anindita
  • Ramírez-Angulo, Jaime
  • López Martín, Antonio
  • González Carvajal, Ramón
  • Díaz Sánchez, Alejandro
A simple technique to greatly enhance the DC open-loop gain of a Miller op-amp is introduced here. It is based on the utilization of nested regulated cascode amplifiers. It uses conventional Miller compensation and does not increase the supply voltage. The proposed scheme has a DC open-loop gain Figure of Merit FoMAOLDC=24,614kV/V.pF.MHz/µWatt. It is especially appropriate for utilization in modern deep sub-micrometer CMOS technologies with low intrinsic gain., This work was supported in part by the Spanish Ministerio Ciencia e Innovación and the FEDER funds under Grant TEC2016-80396-C2
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Class AB amplifier with enhanced slew rate and GBW

  • Garde Luque, María Pilar
  • López Martín, Antonio
  • Algueta-Miguel, Jose M.
  • Ramírez-Angulo, Jaime
  • González Carvajal, Ramón
The design of a micropower class AB operational transconductance amplifier with large dynamic current to quiescent current ratio is addressed. It is based on a compact and power-efficient adaptive biasing circuit and a class AB current follower using the Quasi-Floating Gate (QFG) technique. The amplifier has been designed and fabricated in a 0.5 um CMOS process. Simulation and measurement results show a slew rate (SR) improvement factor versus the class A version larger than 4 for the same supply voltage and bias currents, as well as enhanced small-signal performance., Grant TEC2016‐80396‐C2‐1‐R (AEI/FEDER) and Obra Social La Caixa—Fundación Caja Navarra
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

1-V 15-μW 130-nm CMOS super class AB OTA

  • López Martín, Antonio
  • Algueta-Miguel, Jose M.
  • Garde Luque, María Pilar
  • González Carvajal, Ramón
  • Ramírez-Angulo, Jaime
A super class AB recycling folded cascode amplifier in 130 nm CMOS is presented. It combines for the first time adaptive biasing of the differential input pair, nonlinear current mirrors with current starving and dynamic biasing of the cascode transistors in the output branch. Measurements using a ±0.5V supply show slew rate and gain bandwidth product improvement factors of 26 and 112 versus the conventional topology for the same bias currents, yielding the highest combined FoM to date., This work has been supported in part by grant TEC2016-80396-C2 (AEI/FEDER).
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

360 nW gate-driven ultra-low voltage CMOS linear transconductor with 1 MHz bandwidth and wide input range

  • Rico-Aniles, Héctor Daniel
  • Ramírez-Angulo, Jaime
  • López Martín, Antonio
  • González Carvajal, Ramón
A low voltage linear transconductor is introduced. The circuit is a pseudo differential architecture that operates with ±0.2V supplies and uses 900nA total biasing current. It employs a floating battery technique to achieve low voltage operation. The transconductor has a 1MHz bandwidth. It exhibits a SNR = 72dB, SFDR = 42dB and THD = 0.83% for a 100mVpp 10kHz sinusoidal input signal. Moreover, stability is not affected by the capacitance of the signal source. The circuit has been validated with a prototype chip fabricated in a 130nm CMOS technology., This work was supported in part by the Agencia Estatal de Investigacion/Fondo Europeo de Desarrollo Regional under Grant TEC2016-80396-C2. The work of Hector D. Rico-Aniles was supported by the Mexican Consejo Nacional de Ciencia y Tecnologia for the through an Academic Scholarship under Grant 408946.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Power efficient simple technique to convert a reset-and-hold into a true-sample-and-hold using an auxiliary output stage

  • Rico-Aniles, Héctor Daniel
  • Ramírez-Angulo, Jaime
  • López Martín, Antonio
  • González Carvajal, Ramón
  • Rocha-Pérez, José Miguel
  • Garde Luque, María Pilar
A technique to implement true-sample-and-hold circuits that hold the output for almost the entire clock cycle without resetting to zero is introduced, alleviating the slew rate requirement on the op-amp. It is based on a Miller op-amp with an auxiliary output stage that increases power dissipation by only 1.3%. The circuit is offset-compensated and has close to rail-to-rail swing. Experimental results of a test chip prototype in 130nm CMOS technology with 0.3mW power dissipation are provided, which validate the proposed technique., This work was supported by a Grant TEC2016-80396-C2 (AEI/FEDER). The work of Héctor Daniel Rico-Aniles was supported by the Mexican Consejo Nacional de Ciencia y Tecnología (CONACYT) through an academic scholarship under Grant 408946.