Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 4
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Integrated computational modeling of large format additive manufacturing: Developing a digital twin for material extrusion with carbon fiber-reinforced acrylonitrile butadiene styrene

  • Castelló-Pedrero, Pablo|||0000-0002-6927-6430
  • García-Gascón, César|||0009-0007-6772-0474
  • Javier Bas-Bolufer
  • García Manrique, Juan Antonio|||0000-0001-9507-0746
[EN] Material extrusion (MEX) continues to be a pivotal additive manufacturing (AM) process, involving the selective heating and layer-by-layer deposition of material. However, conventional finite-element models (finite-element analysis) face limitations in accurately simulating the MEX process, highlighting the need for experimental validation. This paper highlights an advanced material modeling technology that streamlines the development of composite parts using large format AM (LFAM). It specifically focuses on a thermoplastic acrylonitrile butadiene styrene (ABS) matrix composite material enriched with 20% short carbon fibers. The study employs integrated computational materials engineering, integrating (i) the manufacturing process, (ii) the material¿s microstructure, (iii) homogenization techniques, and (iv) the performance of the final part. The development of a digital twin for pellet extrusion is proposed, emphasizing the importance of micro-structure characterization to account for warpage and residual stresses that lead to part distortion. The demonstrator manufactured for this study is a wind turbine mold of a blade section. Experimental tests revealed an elastic modulus of 5.5¿GPa and a hardening modulus of 2.4¿GPa for the composite. The numerical microscopic model showed a 16% error in the elastic modulus compared to experimental results. The study concludes that the homogenization techniques are effective in predicting the elastic properties but lack accuracy in the plastic region. The application of the model to the LFAM process of pellet extrusion is demonstrated, with simulation results showing a maximum deformation close to the center of the wind turbine blade mold., This work was supported by Generalitat Valencia (GVA) and the Spanish Ministry of Science and Innovation (INVEST/2022/131, CIACIF/2021/286, IDIFEDER/2021/040, TED2021-130879B-C21 and PID2019-108807RB-I00).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Multiscale numerical modeling of large-format additive manufacturing processes using carbon fiber reinforced polymer for digital twin applications

  • Castelló-Pedrero, Pablo|||0000-0002-6927-6430
  • García-Gascón, César|||0009-0007-6772-0474
  • García Manrique, Juan Antonio|||0000-0001-9507-0746
[EN] Large Format Additive Manufacturing (LFAM) has gained prominence in the aerospace and automotive industries, where topology optimization has become crucial. LFAMfacilitates the layer-by-layer production of sizeable industrial components in carbon fiber (CF) reinforced polymers, however 3D printing at large scales results in warpage generation. Printed components are deformed as residual stresses generated due to thermal gradients between adjacent layers. This paper tackles the problem at two different scales: the micro and macroscale. Initially, the microstructure characterization of the thermoplastic ABS matrix composite material enriched with 20% short CF is used in the development of numerical models to understand the mechanical behavior of the studied material. Numerical modeling is performed simultaneously by means of Mean-Field (MF) homogenization methods and Finite Element Analysis (FEA). Outcomes validated with corrected experimental mechanical testing results show a discrepancy in the elastic modulus of 7.8% with respect to FE multi-layer analysis. Micro-level results are coupled with the a macroscopic approach to reproduce the LFAM process, demonstrating the feasibility of the tool in the development of a Digital Twin (DT)., Open Access funding provided thanks to the CRUE-CSIC agreement with Springer Nature. This work was supported by Generalitat Valencia (GVA) and Spanish Ministry of Science and Innovation. INVEST/2022/131, CIACIF/2021/286, TED2021-130879B-C21 and CIPROM/2022/3.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Impact of deposition time per layer in large format additive manufacturing with glass fiber reinforced ABS

  • Castelló-Pedrero, Pablo|||0000-0002-6927-6430
  • García-Gascón, César|||0009-0007-6772-0474
  • Javier Bas-Bolufer
  • García Manrique, Juan Antonio|||0000-0001-9507-0746
  • Alabort-Martínez, Carles
[EN] This paper presents a parametric study of layer adhesion in Large Format Additive Manufacturing (LFAM) applications using glass fiber (GF) reinforced acrylonitrile butadiene styrene (ABS). The study focuses on the deposition time per layer (tL) and includes an innovative approach to monitor temperature variation throughout the printing process using an infrared camera. The paper provides a detailed account of the sample fabrication process and experimental tensile tests. Specifically, this study shows how lower times per layer yield better mechanical properties as material is deposited over hotter layers, resulting in smaller thermal gradients, hence better layer adhesion and reduced warpage., This work was supported by Generalitat Valencia (GVA) and Spanish Ministry of Science and Innovation. INVEST/2022/131, CIA-CIF/2021/286, TED2021-130879B-C21 and CIPROM/2022/3
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Interlayer adhesion in Large Format Additive Manufacturing of glass fiber reinforced ABS structures

  • Castelló-Pedrero, Pablo|||0000-0002-6927-6430
  • Javier Bas-Bolufer
  • García-Gascón, César|||0009-0007-6772-0474
  • García Manrique, Juan Antonio|||0000-0001-9507-0746
  • Chinesta, Francisco
[EN] Large Format Additive Manufacturing (LFAM) is a promising technology for the rapid production of molds for high-performance composite parts in aerospace and automotive applications. Using ABS reinforced with short glass fibers (20% by weight) as granules improves production rates and mechanical performance. However, interlayer adhesion remains a major challenge, as the interface between layers is typically the weakest point in printed structures. This study examines the effects of three printing parameters on interlayer adhesion: time per layer ( ), nozzle temperature ( ), and extrusion factor ( ). The ABS/20GF composite is first characterized to determine its thermal and physical properties. An infrared camera monitors temperature evolution during printing, and tensile tests with loads applied perpendicular to the printing direction evaluate mechanical performance. Microstructural analysis reveals fracture mechanisms between layers. Results show that interlayer adhesion improves with shorter and higher and values. Thermal monitoring indicates a strong correlation between enhanced strength and reduced temperature gradients between layers, enabling better polymer chain mobility and bonding. ANOVA analysis identifies and as statistically significant factors influencing interlayer adhesion. These findings provide valuable insights for optimizing LFAM process parameters to enhance the structural integrity of fiber-reinforced thermoplastic components., The authors would like to acknowledge Generalitat Valenciana (GVA), Spain and Spanish Ministry of Science and Innovation, Spain (Grant No.: TED2021-130879B-C21, CIACIF/2021/286, PID2023-1511 10OB-I00 and CIPROM/2022/3) to provide funds for conducting experiments and software licenses. This research is part of the programme DesCartes (INP06437) and is supported by the National Research Foundation, Prime Minister s Office, Singapore under its Campus for Research Excellence and Technological Enterprise (CREATE) programme.