Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 13
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Proyecto fin de carrera (BachelorThesis)

Eliminación de Naproxeno presente en disoluciones acuosas mediante tratamiento electroquímico con ánodos de papel de carbono modificados superficialmente, Elimination of Naproxen present in aqueous solutions by electrochemical treatment with surface modified carbon paper anodes, Eliminació de Naproxé present en dissolucions acuoses mitjançant tractament electroquímic amb ànodes de paper de carboni modificats superficialment

  • Olcina Doménech, Laura
[ES] El propósito de este trabajo de fin de grado ha sido realizar diversos ensayos de laboratorio con el objetivo de sintetizar, caracterizar y emplear electrodos de papel de carbono en procesos de electrólisis para la eliminación de antiinflamatorios no esteroides, como el Naproxeno. Se investigó la degradación del Naproxeno en soluciones acuosas mediante oxidación electroquímica, utilizando ánodos de papel de carbono con y sin modificación superficial. Esta se realizó mediante la síntesis de nanopartículas de platino y óxido de grafeno reducido más nanopartículas de platino, utilizando técnicas de voltamperometría y cronoamperometría. Además, también se evaluó la influencia en la electrolisis del electrolito utilizado. Durante los procesos de electrólisis se evaluaron el tiempo empleado, la carga eléctrica y el voltaje. Además, se utilizó un equipo de cromatografía HPLC para obtener un seguimiento continuo del área del pico cromatográfico de cada muestra. Posteriormente, se evaluó la energía eléctrica consumida mediante comparativas de las cinéticas de degradación, así como la estabilidad de los diferentes ánodos. Para ello, se utilizaron análisis FESEM y EDX en los ánodos asociados a los distintos procesos. Finalmente, se estudió la viabilidad económica y el coste energético de aplicar los métodos utilizados para tratar aguas residuales a escala industrial., [EN] The purpose of this undergraduate thesis has been to conduct various laboratory tests with the aim of synthesizing, characterizing, and utilizing carbon paper electrodes in electrolysis processes for the removal of non-steroidal anti-inflammatory drugs, such as Naproxen. The influence of Naproxen removal from aqueous solutions through electrochemical oxidation was investigated using carbon paper anodes with and without surface modification. The surface modification was carried out through the synthesis of platinum nanoparticles or reduced graphene oxide and platinum nanoparticles, using voltammetry and chronoamperometry techniques. Additionally, the influence of the electrolyte during the electrolysis processes was also evaluated. During the electrolysis processes, the time employed, electric charge, and voltage were evaluated too. Furthermore, an HPLC chromatography system was used to obtain continuous monitoring of the chromatographic peak area for each sample. Subsequently, the electric energy consumed was evaluated through comparatives of degradation kinetics, as well as the stability of the different anodes. For this purpose, FESEM and EDX analysis were used on the anodes associated with different processes. Finally, the economic feasibility and energy cost of applying the methods used in industrial wastewater were studied., [CA] El propòsit d'aquest treball de fi de grau ha sigut dur a terme diversos assajos de laboratori amb l'objectiu de sintetitzar, caracteritzar i utilitzar elèctrodes de paper de carbono en processos d'electròlisi per a l'eliminació d'antiinflamatoris no esteroides, com el Naproxé. S'ha investigat la influència d'eliminar el Naproxé en dissolucions aquoses mitjançant l'oxidació electroquímica, fent servir ànodes de paper de carbono amb i sense modificació superficial. Aquesta s'ha realitzat mitjançant la síntesi de nanopartícules de platí i òxid de grafè reduït més nanopartícules de platí, fent servir per aconseguir-ho tècniques de voltamperometria i cronoamperometria. A més, també s'ha avaluat la influència de l'electròlit utilitzat en l’electròlisi. Durant els processos d'electròlisi s’ha avaluat el temps utilitzat, la càrrega elèctrica i el voltatge. A més, s’utilitzà un equip de cromatografia HPLC per obtindre un seguiment continu de l'àrea del pic cromatogràfic de cada mostra. Posteriorment, s’avaluà l'energia elèctrica consumida mitjançant comparatives de les cinètiques de degradació, així com l'estabilitat dels diferents ànodes. Per fer-ho, s’ha fet ús d'anàlisis FESEM i EDX en els ànodes associats als diferents processos. Finalment, s’estudià la viabilitat econòmica i el cost energètic d'aplicar els mètodes emprats per tractar aigües residuals a escala industrial., Agradezco al Instituto Tecnológico Metalmecánico, Muebla, Madera, Embalaje y Afines (AIDIMME) por proporcionarme el papel de carbono con el que se ha experimentado como ánodo durante todo el proyecto.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Datos de investigación Set de datos (Dataset)

Cell prototype based on textile electrodes for dyestuff wastewater electrolysis [Dataset], Development and application of an electrolysis cell prototype based on textile electrodes: dyestuff wastewater electrolysis

  • Cases, Francisco|||0000-0001-8105-4489
  • Soler Micó, Ignacio
  • Orts Maiques, Francisco José|||0000-0001-8254-8042
  • Bonastre Cano, José Antonio|||0000-0002-5068-6608
  • Molina Puerto, Javier|||0000-0003-3378-8271
  • Micó-Vicent, B.|||0000-0001-8845-1495
[EN] This research work studies the development of an electrochemical cell prototype based on textile electrodes for treating wastewater via electrochemical processes. The present prototype proposes a system that offers greater efficiency regarding the size/surface of electrodes in electrolysis processes. This prototype enables the treatment of large volumes of dissolution. Moreover, this prototype could surface modify textile electrodes by an electrochemical process in the same cell, specifically, an electrochemically reduced graphene oxide intermediate layer and an outer layer of electrochemically reduced metal nanoparticles are proposed. Surface modification by reduced graphene oxide increase the textile electrode’s stability, conductivity, and specific surface, whilst Pt nanoparticles increase electroactivity. Amaranth was selected to validate the use of this prototype in treating emerging pollutants. This is an azoic dye with a simple structure. Various analytical techniques demonstrate that colour removal takes place with an electrical energy consumption of between 0.29 and 4.66 kWh m−3 (depending on the operational specifications of the electrolysis performed). Once the colour is removed, total organic carbon and chemical oxygen demand decreases by up to 49% and 37%, respectively., This research is part of the Spanish R+D+i contract (TED2021-130905B-I00 funded by MCIN/ AEI/10.13039/501100011033 and the “European Union NextGenerationEU/PRTR”). The authors wish to acknowledge the Spanish AEI Research Network (Contract RED2022-134552-T). Chemviron Carbon, who kindly donated the FlexzorbTM FM10 activated carbon fabrics and Funding for open access charge CRUE-Universitat Politècnica de València, are acknowledged too. The authors are grateful for the English revision by John Rawlins and Tim Vickers.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Naproxen electrooxidation using carbon paper electrodes modified with reduced graphene oxide and platinum nanoparticles

  • Molina Puerto, Javier|||0000-0003-3378-8271
  • Bonastre Cano, José Antonio|||0000-0002-5068-6608
  • Cases, Francisco|||0000-0001-8105-4489
  • Olcina, L.
[EN] This research study investigates the electrooxidation of naproxen (NPX), an anti-inflammatory pharmaceutical, on modified carbon paper (CP) electrodes. Electrochemical modification of CP electrodes was accomplished with Pt or reduced graphene oxide (RGO)-Pt coatings, resulting in the production of electroactive electrodes. RGO coatings synthesized by cyclic voltammetry (CV) for 10 scans provided the optimal coverage for the CP electrode surface. The deposition of Pt nanoparticles (Pt NPs) on the electrodes (CP or CP-RGO) by CV produced a good electrode surface coverage with 20 synthesis scans. The voltammetric analysis of the electrodes in 230 mg/L NPX solution showed oxidation peaks around 1.0 to 1.2 V. Moreover, the inclusion of RGO in the coating led to an increase in the current density of these oxidation peaks and a decrease of the electrode electron transfer resistance as measured by electrochemical impedance spectroscopy. The electrolysis of NPX in different electrolytes (Na2SO4 and Na2SO4/NaCl) was conducted at 1.4 V, and the removal of NPX was analyzed using high-performance liquid chromatography. The CP-RGO-Pt electrode in Na2SO4/NaCl media showed the fastest NPX degradation kinetics, resulting in a 90 % degradation in only 90 min with low charge consumption (0.07 AhL-1). The smaller size of Pt NPs deposited on CP-RGO, as observed by field emission scanning electron microscopy and transmission electron microscopy, contributed to the higher electrochemical response in CV and a faster kinetic degradation of NPX., This research is part of the Spanish R + D + i contract TED2021-130905B-I00 funded by MCIN/AEI/10.13039/501100011033 and by the European Union NextGenerationEU/PRTR as well as the Red E3Tech Plus: Proyecto Redes de Investigacion de la AEI Network E3Tech PLUS (RED2022-134552-T) project. Funding for open access charge: CRUE-Universitat Politecnica de Valencia. The Electron Microscopy Service of the UPV (Universitat Politecnica de Valencia) is gratefully acknowledged for help with FESEM and EDX characterization.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Electrochemical degradation of micro/nanoplastics in water: recent results

  • Rodrigo, R.
  • Bonastre Cano, José Antonio|||0000-0002-5068-6608
  • Molina Puerto, Javier|||0000-0003-3378-8271
  • Cases, Francisco|||0000-0001-8105-4489
[EN] Microplastics and nanoplastics have emerged as critical environmental contaminants due to their ubiquitous presence, persistence, and potential risks to human health and ecosystems. These particles, derived from the fragmentation of plastic waste, can adsorb other contaminants, penetrate biological barriers, and accumulate in living organisms. Wastewater treatment plants act as both sources and sinks of microplastics and nanoplastics, retaining a significant fraction of these pollutants but failing to remove them completely. In addition, conventional treatment processes can induce the fragmentation of microplastics into nanoplastics, increasing the problem. Given the limited effectiveness of traditional physical, chemical, or biological separation methods, advanced oxidation processes have emerged as promising alternatives. Among them, electrochemical oxidation, based on the in situ generation of reactive oxygen species such as hydroxyl radicals, has demonstrated high efficiency in degrading organic pollutants. This review analyses the most recent advancements in the use of electrochemical oxidation, highlighting the use of boron-doped diamond anodes and other electrochemical configurations. Experimental studies with different operating conditions, combinations with complementary techniques and the impact of electrocatalytic materials on the efficiency of the process are addressed. The reported results demonstrate degradation rates above 90% under specific conditions, without generating toxic by-products, and with reasonable energy consumption. Electrochemical oxidation enables the mineralization of polymeric particles and adapts to different water matrices. Further research at pilot- and industrial-scale is required to optimize operations and validate its long-term feasibility. Overall, electrochemical oxidation is emerging as a strategic tool for advanced wastewater treatment., This research is part of the Spanish R+D+i contract TED2021-130905B-I00 funded by MCIN/ AEI/10.13039/501100011033 and by the European Union NextGenerationEU/PRTR as well as the Red E3Tech Plus: Proyecto Redes de Investigación de la AEI Network E3Tech PLUS (RED2022-134552-T) project. Funding for open access charge: CRUE-Universitat Politècnica de València.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Datos de investigación Set de datos (Dataset)

Electrooxidation of polystyrene nanoplastics by modified Ti-felt electrodes, High surface area modified Ti-felt electrodes for the degradation of polystyrene nanoplastics

  • Cases, Francisco|||0000-0001-8105-4489
  • Bonastre Cano, José Antonio|||0000-0002-5068-6608
  • Molina Puerto, Javier|||0000-0003-3378-8271
  • Rodrigo Roca, Rubén
[EN] Ti-felt electrodes with high surface area have been used as supports of electroactive coatings (Pt and SnO₂–Sb–Pt). The electrodes obtained have been employed for the electrochemical oxidation of polystyrene nanoplastics (NPs) (100 nm) in solution. Voltammetric characterization of the electrodes with Ru(NH₃)₆Cl₃ and K₃Fe(CN)₆ redox mediators showed a substantial increase in the redox peaks' current density compared to the boron‑doped diamond electrode. For example, this increase was >68‑fold for the SnO₂–Sb–Pt electrode when using the Ru(NH₃)₆Cl₃ redox mediator. This can be attributed to the enhanced surface area of Ti‑felt, composed of 20 μm diameter fibers, and the roughness of the electrocatalyst coatings. Voltammetric characterization of Ti‑Pt and Ti‑SnO₂–Sb–Pt in 0.03 M Na₂SO₄ media showed an increase in the anodic current density when adding NPs, which would account for a direct mechanism of electrooxidation of the electrode. •OH, S₂O₈²⁻, H₂O₂, and O₃ generation were also determined for both types of electrodes. The degradation of NPs was monitored by fluorescence spectroscopy, taking advantage of the fluorescence of styrene. In addition, it was observed that the dispersion of the second‑order diffraction light (this phenomenon takes place in the diffraction grating of the monochromator) by NPs could also be used to monitor the evolution of the NPs concentration in solution. The electrochemical degradation of polystyrene NPs was faster with SnO₂–Sb–Pt modified Ti‑felt‑based electrodes than with the Pt‑modified one (reaching 90 % degradation in 100 and 210 minutes at 25 mA·cm⁻², respectively). Electrochemical energy consumption per order was also lower for SnO₂–Sb–Pt‑modified electrodes., This research is part of the Spanish R+D+i contract TED2021-130905B-I00 funded by MCIN/AEI /10.13039/501100011033 and by the European Union NextGenerationEU/PRTR as well as the Red E3Tech Plus: Proyecto Redes de Investigación de la AEI Network E3Tech PLUS (RED2022-134552-T) project. Funding for open access charge: CRUE-Universitat Politècnica de València. The Electron Microscopy Service of the UPV (Universitat Politècnica de València) is gratefully acknowledged for its help with FESEM, EDX, and TEM characterization.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Datos de investigación Set de datos (Dataset)

Electrooxidation of polystyrene nanoplastics by BDD electrodes [Dataset], Influence of the doping level of boron-doped diamond electrodes in the electrooxidation of polystyrene nanoplastics

  • Cases, Francisco|||0000-0001-8105-4489
  • Rodrigo Roca, Rubén
  • Molina Puerto, Javier|||0000-0003-3378-8271
  • Bonastre Cano, José Antonio|||0000-0002-5068-6608
  • Muñoz Ortuño, Lucía
[EN] Microplastics and nanoplastics have arisen as contaminants of emerging concern due to the wide use of plastics, and the application of boron-doped diamond (BDD) electrodes for their removal is promising. In this study, we report the influence of BDD doping levels (500, 2500, and 10000 ppm B doping) on the electrooxidation of polystyrene nanoplastics (100 nm, 20 mg⋅L-1). Different current densities (50, 25, 12.5, and 5 mA⋅cm-2) have been applied to determine the best electrolysis conditions for each electrode type. In addition, hydroxyl radical (•OH), persulphate (S2O82-), and hydrogen peroxide (H2O2) reactive species have been determined to understand the influence of the species generated on the degradation of NPs. BDD500 electrode presents the fastest degradation of PS NPs at low current densities (12.5 and 5 mA⋅cm-2), BDD2500 at 25 mA⋅cm-2, and BDD10000 at 50 mA⋅cm-2. Among oxidative species determined, S2O82- is the one generated with the highest concentration and seems to command the degradation of PS NPs, since at 25, 12.5, and 5 mA⋅cm-2, the electrodes that produce more S2O82- degrade faster PS NPs. At 50 mA⋅cm-2, the differences between the different electrodes were minimal. The highest mineralization (as measured by non-purgeable organic carbon measurements) was obtained for BDD500 at 50, 25, and 12.5 mA⋅cm-2, and BDD2500 at 5 mA⋅cm-2., This research is part of the Spanish R +D +i contract TED2021-130905B-I00 funded by MCIN/AEI /10.13039/501100011033 and by the European Union NextGenerationEU/PRTR as well as the Red E3Tech Plus: Proyecto Redes de Investigación de la AEI Network E3Tech PLUS (RED2022-134552-T) project. Funding for open access charge: CRUE- Universitat Politècnica de València. The Electron Microscopy Service of the UPV (Universitat Politècnica de València) is gratefully acknowledged for help with TEM and FESEM characterization.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Datos de investigación Set de datos (Dataset)

Electrochemical removal of polystyrene nanoplastics in a filter-press reactor using modified Ti-felt anodes [Dataset]

  • Cases, Francisco|||0000-0001-8105-4489
  • Molina Puerto, Javier|||0000-0003-3378-8271
  • Bonastre Cano, José Antonio|||0000-0002-5068-6608
  • Rodrigo Roca, Rubén
Ti-felt anodes, with high surface area, have been used as supports of Pt and SnO2-Sb-Pt electrocatalysts. Anodes have been applied in a filter-press electrochemical reactor for the electrooxidation of polystyrene nanoplastics (NPs) (100 mg·L-1). Two types of configurations have been used. In the first, the solution with NPs flows through the anode, taking advantage of its porosity (acting as a sort of membrane) to enhance the contact of NPs with the anode and the oxidative species generated. In the second configuration, the solution of NPs flows parallel to the anode, and the NPs flow parallel to it. Comparing both configurations at 25 mA·cm-2, for the Ti-Pt anode, the flow-through configuration decreases energy consumption by ~7-fold and treatment time by ~15-fold when compared to the flow-by configuration. For Ti-SnO2-Sb-Pt anode, ratios of ~6.5-fold and ~13-fold were obtained, respectively. Moreover, the effect of the current density (50, 25, 12.5, and 5 mA·cm-2) was studied. For the Ti-Pt electrode, a treatment time of only 40 minutes was achieved at a current density of 25 mA·cm-2 with the F-T configuration, with a faradaic efficiency of 62.09 %, and electrochemical energy per order (EEO) of 21.91 kW·h·m-3·order-1. In the case of the F-B configuration at 25 mA·cm-2 the treatment time increases until 600 min, with a faradaic efficiency of 8.27 % and EEO of 156.57 kW·h·m- 3·order-1., This research is part of the Spanish R+D+i contract TED2021-130905B-I00 funded by MCIN/AEI /10.13039/501100011033 and by the European Union NextGenerationEU/PRTR as well as the Red E3Tech Plus: Proyecto Redes de Investigación de la AEI Network E3Tech PLUS (RED2022-134552-T) project. Funding for open access charge: CRUE-Universitat Politècnica de València. The Electron Microscopy Service of the UPV (Universitat Politècnica de València) is gratefully acknowledged for its help with FESEM, EDX, TEM, and XRM characterization.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

High surface area modified Ti-felt electrodes for the degradation of polystyrene nanoplastics

  • Rodrigo-Roca, Rubén
  • Bonastre Cano, José Antonio|||0000-0002-5068-6608
  • Molina Puerto, Javier|||0000-0003-3378-8271
  • Cases, Francisco|||0000-0001-8105-4489
[EN] Ti-felt electrodes with high surface area have been used as supports of electroactive coatings (Pt and SnO2-Sb-Pt). The electrodes obtained have been employed for the electrochemical oxidation of polystyrene nanoplastics (NPs) (100 nm) in solution. Voltammetric characterization of the electrodes with Ru(NH3)6Cl3 and K3Fe(CN)6 redox mediators showed a substantial increase in the redox peaks¿ current density compared to the boron-dopeddiamond electrode. For example, this increase was >68-fold for the SnO2-Sb-Pt electrode when using the Ru (NH3)6Cl3 redox mediator. This can be attributed to the enhanced surface area of Ti-felt, composed of 20 m diameter fibers, and the roughness of the electrocatalyst coatings. Voltammetric characterization of Ti-Pt and TiSnO2-Sb-Pt in 0.03 M Na2SO4 media showed an increase in the anodic current density when adding NPs, which would account for a direct mechanism of electrooxidation of the electrode. OH, S2O82, H2O2, and O3 generation were also determined for both types of electrodes. The degradation of NPs was monitored by fluorescence spectroscopy, taking advantage of the fluorescence of styrene. In addition, it was observed that the scattering of the second-order diffraction light (this phenomenon takes place in the diffraction grating of the monochromator) by NPs could also be used to monitor the evolution of the NPs concentration in solution. The electrochemical degradation of polystyrene NPs was faster with SnO2-Sb-Pt modified Ti-felt based electrodes than with the Ptmodified one (reaching 90 % degradation in 100 and 210 min at 25 mA cm 2, respectively). Electrochemical energy consumption per order was also lower for SnO2-Sb-Pt-modified electrodes., This research is part of the Spanish R + D + i contract TED2021-130905B-I00 funded by MCIN/AEI /10.13039/501100011033 and by the European Union NextGenerationEU/PRTR as well as the Red E3Tech Plus: Proyecto Redes de Investigacion ¿ de la AEI Network E3Tech PLUS (RED2022-134552-T) project. Funding for open access charge: CRUE Universitat Polit`ecnica de Val`encia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Electrochemical removal of polystyrene nanoplastics in a filter-press reactor using modified Ti-felt anodes: comparison of flow-through and flow-by configurations

  • Rodrigo-Roca, Rubén
  • Bonastre Cano, José Antonio|||0000-0002-5068-6608
  • Molina Puerto, Javier|||0000-0003-3378-8271
  • Cases, Francisco|||0000-0001-8105-4489
[EN] Ti-felt anodes with high surface area were used as supports for Pt and SnO₂–Sb–Pt electrocatalysts. The anodes were tested in a filter-press electrochemical reactor for the electrooxidation of polystyrene nanoplastics (NPs) at an initial concentration of 100 mg·L⁻¹. Two reactor configurations were evaluated. In the first one (flow-through, F–T), the NP suspension was forced through the porous anode, which acted as a permeable electrode, enhancing contact between the NPs and both the anode surface and the oxidizing species generated in situ. In the second configuration (flow-by, F–B), the NP suspension flowed parallel to the anode surface. At 25 mA·cm⁻², the flow-through configuration substantially outperformed the flow-by configuration. For the Ti–Pt anode, F–T reduced energy consumption by approximately 7-fold and treatment time by about 15-fold relative to F–B. For the Ti–SnO₂–Sb–Pt anode, the corresponding reductions were ~6.5-fold in energy consumption and ~13-fold in treatment time. The influence of current density (50, 25, 12.5, and 5 mA·cm⁻²) was also investigated. For the Ti–Pt electrode operating in the F–T mode at 25 mA·cm⁻², a treatment time of only 40 min was achieved, with a Faradaic efficiency of 62.09% and an electrochemical energy per order (EEO) of 21.91 kW·h·m⁻³·order⁻¹. In contrast, under the F–B configuration at the same current density, the treatment time increased to 600 min, with a Faradaic efficiency of 8.27% and an EEO of 156.57 kW·h·m⁻³·order⁻¹., This research is part of the Spanish R+D+i contract TED2021-130905B-I00 funded by MCIN/AEI /10.13039/501100011033 and by the European Union NextGenerationEU/PRTR as well as the Red E3Tech Plus: Proyecto Redes de Investigación de la AEI Network E3Tech PLUS (RED2022-134552-T) project. Funding for open access charge: CRUE-Universitat Politecnica de Valencia is acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Tesis doctoral (DoctoralThesis)

Estudio de la oxidación electroquímica de nanoplásticos

  • Rodrigo Roca, Rubén
[ES] La presencia de microplásticos y nanoplásticos en el medio ambiente se ha consolidado en los últimos años como uno de los principales problemas emergentes en el ámbito de la contaminación. En particular, los nanoplásticos presentan una elevada persistencia, una alta dispersión y un potencial impacto en los ecosistemas y en la salud humana. A pesar de la elevada eficiencia de las estaciones depuradoras de aguas residuales en la retención de micro y nanoplásticos, una fracción significativa continúa liberándose al medio acuático o acumulándose en los lodos de depuración. Este escenario pone de manifiesto la necesidad de desarrollar tratamientos terciarios avanzados capaces no solo de separar, sino también de degradar eficazmente los nanoplásticos. En este contexto, la presente tesis se centra en el estudio y desarrollo de procesos de electrooxidación como tecnología de oxidación avanzada para la degradación de nanoplásticos de poliestireno. La investigación se plantea como un desarrollo progresivo, a partir del estudio del comportamiento de electrodos planos convencionales de diamante dopado con boro, con el fin de identificar sus principales limitaciones en términos de cinética y consumo energético, para posteriormente diseñar, validar y escalar nuevos electrodos tridimensionales de mayor eficiencia. En una segunda etapa, se desarrollaron y caracterizaron electrodos de fieltro de Ti modificados con recubrimientos de Pt, SnO2-Sb-Pt, obteniendo materiales con una elevada área electroactiva gracias a sus fibras de 20 µm de diámetro. La caracterización mediante técnicas voltamétricas y espectroscopía de impedancia electroquímica demostró un incremento muy significativo de la electroactividad respecto a los electrodos convencionales. Este incremento en el rendimiento se asocia principalmente a la elevada área superficial del material. La degradación de nanoplásticos de poliestireno en sistemas de electrooxidación en celda electroquímica evidenció que los electrodos de fieltro de Ti permiten alcanzar elevados grados de degradación con tiempos de tratamiento y consumos energéticos menores. Posteriormente, la tesis aborda el salto de escala y rediseño del reactor electroquímico, pasando de celdas batch de laboratorio a un reactor de tipo filtro-prensa, en el que los electrodos de fieltro de Ti se utilizan como membranas electroactivas. Los resultados demuestran que al obligar a los nanoplásticos a atravesar la estructura del electrodo se observan reducciones muy significativas tanto en el tiempo de tratamiento como en el consumo eléctrico. Previamente se realizó un estudio sobre la retención física de los nanoplásticos para comparar los resultados con y sin el paso de corriente. El estudio sistemático del efecto de la densidad de corriente puso de manifiesto que es posible alcanzar degradaciones >90% en tiempos muy reducidos para concentraciones iniciales de 100 mg·L-1, del orden de 30 minutos para los electrodos Ti-Pt y de 40 minutos para Ti-SnO2-Sb-Pt, con valores de eficiencia energética considerablemente inferiores a los reportados en la bibliografía para otros sistemas electroquímicos. En conjunto, la presente tesis demuestra que el uso de electrodos de fieltro de Ti, modificados con Pt o SnO2-Sb-Pt, de alta área superficial, operando como membranas electroactivas, constituye una estrategia eficaz para la degradación electroquímica de nanoplásticos. Los avances alcanzados representan un paso relevante hacia la implementación de tecnologías electroquímicas más eficientes, escalables y sostenibles para el tratamiento avanzado de aguas contaminadas con micro y nanoplásticos., Este trabajo ha sido financiado por MCIN/AEI/10.13039/501100011033 y por la Unión Europea NextGenerationEU/PRTR, así como por la Red E3TECH-PLUS. Agradecer a estas instituciones por la concesión del proyecto TED2021-130905B-I00.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Datos de investigación Set de datos (Dataset)

Electrochemical degradation of Naproxen by carbon paper electrodes coated by RGO and Pt, Naproxen electrooxidation using carbon paper electrodes modified with reduced graphene oxide and platinum nanoparticles

  • Molina Puerto, Javier|||0000-0003-3378-8271
  • Bonastre Cano, José Antonio|||0000-0002-5068-6608
  • Cases, Francisco|||0000-0001-8105-4489
  • Olcina Doménech, Laura
This research study investigates the electrooxidation of naproxen (NPX), an anti-inflammatory pharmaceutical, on modified carbon paper (CP) electrodes. Electrochemical modification of CP electrodes was accomplished with Pt or reduced graphene oxide (RGO)-Pt coatings, resulting in the production of electroactive electrodes. RGO coatings synthesized by cyclic voltammetry (CV) for 10 scans provided the optimal coverage for the CP electrode surface. The deposition of Pt nanoparticles (Pt NPs) on the electrodes (CP or CP-RGO) by CV produced a good electrode surface coverage with 20 synthesis scans. The voltammetric analysis of the electrodes in 230 mg/L NPX solution showed oxidation peaks around 1.0 to 1.2 V. Moreover, the inclusion of RGO in the coating led to an increase in the current density of these oxidation peaks and a decrease of the electrode electron transfer resistance as measured by electrochemical impedance spectroscopy. The electrolysis of NPX in different electrolytes (Na2SO4 and Na2SO4/NaCl) was conducted at 1.4 V, and the removal of NPX was analyzed using high-performance liquid chromatography. The CP-RGO-Pt electrode in Na2SO4/NaCl media showed the fastest NPX degradation kinetics, resulting in a 90 % degradation in only 90 min with low charge consumption (0.07 A⋅h⋅L-1). The smaller size of Pt NPs deposited on CP-RGO, as observed by field emission scanning electron microscopy and transmission electron microscopy, contributed to the higher electrochemical response in CV and a faster kinetic degradation of NPX., This research is part of the Spanish R + D + i contract TED2021-130905B-I00 funded by MCIN/AEI/10.13039/501100011033 and by the European Union NextGenerationEU/PRTR as well as the Red E3Tech Plus: Proyecto Redes de Investigaci´on de la AEI Network E3Tech PLUS (RED2022-134552-T) project. Funding for open access charge: CRUE Universitat Polit`ecnica de Val`encia. The Electron Microscopy Service of the UPV (Universitat Polit`ecnica de Val`encia) is gratefully acknowledged for help with FESEM and EDX characterization.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Influence of the doping level of boron-doped diamond electrodes in the electrooxidation of polystyrene nanoplastics

  • Rodrigo-Roca, Rubén
  • Muñoz, Lucía
  • Molina Puerto, Javier|||0000-0003-3378-8271
  • Bonastre Cano, José Antonio|||0000-0002-5068-6608
  • Cases, Francisco|||0000-0001-8105-4489
[EN] Microplastics and nanoplastics have arisen as contaminants of emerging concern due to the wide use of plastics, and the application of boron-doped diamond (BDD) electrodes for their removal is promising. In this study, we report the influence of BDD doping levels (500, 2500, and 10000 ppm B doping) on the electrooxidation of polystyrene nanoplastics (100 nm, 20 mg¿L-1). Different current densities (50, 25, 12.5, and 5 mA¿cm¿ 2 ) have been applied to determine the best electrolysis conditions for each electrode type. In addition, hydroxyl radical (¿OH), persulphate (S2O8 2-), and hydrogen peroxide (H2O2) reactive species have been determined to understand the influence of the species generated on the degradation of NPs. BDD500 electrode presents the fastest degradation of PS NPs at low current densities (12.5 and 5 mA¿cm¿ 2 ), BDD2500 at 25 mA¿cm¿ 2 , and BDD10000 at 50 mA¿cm¿ 2 . Among oxidative species determined, S2O8 2- is the one generated with the highest concentration and seems to command the degradation of PS NPs, since at 25, 12.5, and 5 mA¿cm¿ 2 , the electrodes that produce more S2O8 2- degrade faster PS NPs. At 50 mA¿cm¿ 2 , the differences between the different electrodes were minimal. The highest mineralization (as measured by non-purgeable organic carbon measurements) was obtained for BDD500 at 50, 25, and 12.5 mA¿cm¿ 2 , and BDD2500 at 5 mA¿cm¿ 2 ., This research is part of the Spanish R + D + i contract TED2021-130905B-I00 funded by MCIN/AEI /10.13039/501100011033 and by the European Union NextGenerationEU/PRTR as well as the Red E3Tech Plus: Proyecto Redes de Investigacion ¿ de la AEI Network E3Tech PLUS (RED2022-134552-T) project. Funding for open access charge: CRUEUniversitat Polit`ecnica de Val`encia
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Development and application of an electrolysis cell prototype based on textile electrodes: dyestuff wastewater electrolysis

  • Soler-Micó, Ignacio
  • Orts Maiques, Francisco José|||0000-0001-8254-8042
  • Molina Puerto, Javier|||0000-0003-3378-8271
  • Micó-Vicent, B.|||0000-0001-8845-1495
  • Bonastre Cano, José Antonio|||0000-0002-5068-6608
  • Cases, Francisco|||0000-0001-8105-4489
[EN] This research work studies the development of an electrochemical cell prototype based on textile electrodes for treating wastewater via electrochemical processes. The present prototype proposes a system that offers greater efficiency regarding the size/surface of electrodes in electrolysis processes. This prototype enables the treatment of large volumes of dissolution. Moreover, this prototype could surface modify textile electrodes by an electrochemical process in the same cell, specifically, an electrochemically reduced graphene oxide intermediate layer and an outer layer of electrochemically reduced metal nanoparticles are proposed. Surface modification by reduced graphene oxide increase the textile electrode¿s stability, conductivity, and specific surface, whilst Pt nanoparticles increase electroactivity. Amaranth was selected to validate the use of this prototype in treating emerging pollutants. This is an azoic dye with a simple structure. Various analytical techniques demonstrate that colour removal takes place with an electrical energy consumption of between 0.29 and 4.66 kWh m¿3 (depending on the operational specifications of the electrolysis performed). Once the colour is removed, total organic carbon and chemical oxygen demand decreases by up to 49% and 37%, respectively., This research is part of the Spanish R+D+i contract (TED2021-130905B-I00 funded by MCIN/ AEI/10.13039/501100011033 and the European Union NextGenerationEU/PRTR ). The authors wish to acknowledge the Spanish AEI Research Network (Contract RED2022-134552-T). Chemviron Carbon, who kindly donated the FlexzorbTM FM10 activated carbon fabrics and Funding for open access charge CRUE-Universitat Politècnica de València, are acknowledged too.