Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 4
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Numerical analysis of quad-rotor aerodynamic and aeroacoustic performance with automated trimming algorithm

  • García-Cuevas González, Luis Miguel|||0000-0001-9340-0617
  • García-Tíscar, Jorge|||0000-0003-4934-4587
  • Varela-Martínez, Pau
  • Brendan Hannu Patrick
[EN] The current work introduces a novel and affordable Computational Fluid Dynamics (CFD) methodology for the purpose of assessing the aerodynamic and aero-acoustic performance of multi-rotor systems under trimmed flight conditions. The approach couples a simple Proportional-Integral (P-I) based trim algorithm and steady state CFD solver to automate the process of determining the set of control variables that results in balanced flight conditions. The methodology¿s low computational cost is primarily achieved by including the rotors¿ effects on the flow field with actuator models. A partial validation of the rotor modeling approach in isolated hover conditions reveals slight discrepancies in the computed aerodynamic loads but good agreement with experimental results in terms of the prediction of tonal noise. The CFD procedure is subsequently applied to evaluate a quad-rotor Unmanned Aerial Vehicle¿s (UAV) performance in varied flight scenarios. The obtained results demonstrate that this automated approach effectively predicts quad-rotor performance trends, aligning with previously published data. Key findings include the fact that a hybrid over-mounted fore rotor and under-mounted aft rotor configuration negatively affects forward flight performance, and that the airframe¿s geometry and distribution around the Center of Gravity can have a significant impact on flight characteristics. Finally, comparisons between the automated trim procedure and manually imposed trim parameters in transient aero-acoustic simulations reveal a more accurate approximation of trim when using the automated method. The comparison additionally highlights the importance of simulating multi-rotor systems in physically representative flight conditions as notable differences in the UAV¿s acoustic footprint are observed between cases., The automatic trimming algorithm development was partly sponsored by grant PID2023-150573OB-I00 Design of advanced hydrogen fuel-cell powered aircraft targeting the deployment of sustainable and decarbonised air mobility (AURORA [40]) funded by MICIU/AEI/10.13039/501100011033 and by ERDF/EU and by grant TED2021-131087A-I00 Digital models for the evaluation and reduction of acoustic pollution generated by UAS in urban environments (MODERA [20]) funded by MCIN/AEI/10.13039/501100011033 and by the European Union NextGenerationEU/PRTR. The acoustic study performed in this work was partly sponsored by grant TED2021-131087A-I00 Digital models for the evaluation and reduction of acoustic pollution generated by UAS in urban environments (MODERA [20]) funded by MCIN/AEI/10.13039- /501100011033 and by the European Union NextGenerationEU/PRTR, as well as by grant PID2022-142018OA-I00 Experimental and Numerical Optimization to Lower UAV Acoustical pollution (ENOLA [41]) funded by MCIN/AEI/10.13039/501100011033 and by ERDF, EU. The work was also partially funded by the Universitat Politècnica de València through the Grant FPI-2022-S2-85552. The authors are grateful for the computational resources provided by the Sirius Scientific Computing Cluster at UPV. The authors also wish to acknowledge Mrs. Ada García-Cuevas for christening the aircraft. The authors additionally thank Mathys Ridet, Federico Nahuel Ramírez, José ángel Jarabo Ruiz, and Daniel Velasco Pérez for their help.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Evaluation of different FW-H surfaces and modal decomposition techniques for the acoustic analysis of UAV propellers through detached eddy simulations

  • Broatch, A.|||0000-0001-9991-1039
  • Navarro, Roberto|||0000-0003-2587-4954
  • García-Tíscar, Jorge|||0000-0003-4934-4587
  • Ramírez, Federico N.|||0000-0003-4525-0516
[EN] Noise has been a much-studied problem since the beginning of aviation because it is one of the main factors affecting its social acceptance. In recent years, the expansion of Unmanned Aerial Vehicles (UAVs) has led to increased research on propellers working at low Reynolds numbers, which are typically found in this type of aircraft. This paper begins with an Improved Delayed Detached Eddy Simulation (IDDES) of a commercial nine-inch UAV propeller. The Ffowcs-Williams and Hawkings (FW-H) approach is then used to compute the acoustic propagation from the simulation results. Both aerodynamic performance and acoustic signature results in hover flight are validated experimentally. Then, the influence of different FW-H permeable surfaces is methodologically evaluated, finding that magnified SPL values at low frequencies are obtained when using cylinders due to vortical structures passing through the bottom cap, and that the use of spheres appears to be the most consistent approach. Once a validated, time-resolved flow field has been obtained, different data-driven modal decomposition techniques, such as Proper Orthogonal Decomposition (POD) and Dynamic Mode Decomposition (DMD), are applied to the 3D pressure field. This enables a better understanding of the propeller acoustic modes and the assessment of the suitability of each technique for this problem, especially when Reduced Order Models (ROMs) are sought., This work was partly sponsored by grant TED2021-131087A-I00 Digital models for the evaluation and reduction of acoustic pollution generated by UAS in urban environments (MODERA) funded by MCIN/AEI/10.13039/501100011033 and by the European Union NextGenerationEU/PRTR. The authors thankfully acknowledge the computing resources at Mare Nostrum (grant RES-IM-2023-2-0026) in the framework of the Spanish Supercomputing Network. Funding for open access charge: CRUE-Universitat Politecnica de Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Comprehensive Nonlinear Flutter Instability Analysis via Time-Domain Modal Decomposition in Rotorcraft

  • Gil, A.|||0000-0001-7192-6992
  • Quintero-Igeño, Pedro-Manuel|||0000-0003-4373-2079
  • Álvaro
  • Prothin, Sebastien
  • Doué, Nicolas
[EN] Aeroelastic instabilities are emerging as a significant challenge in both fixed-wing aircraft and propeller design. Although the general conditions that lead to their onset are understood, accurately characterizing the underlying mechanisms remains complex. This paper presents a time-domain modal analysis technique aimed at tracking the development of such instabilities, with particular focus on their onset behavior. Coupled computational fluid dynamics/computational structural dynamics simulations are performed on a flat-plate rotor configuration, and evidence points to a mode-coalescence-type flutter instability that, over a specific range of rotational speeds Omega, evolves into a limit-cycle oscillation driven by stall flutter. The results show satisfactory agreement with available experimental data, although areas for improvement in the simulation setup are identified, including material modeling choices and the absence of hysteresis effects associated with blade loading. The proposed analysis method has been validated only for the flat-plate geometry that, despite offering simplifications in simulation setup, introduces complex aerodynamic nonlinearities. As such, future work will focus on extending the validation to classical airfoil sections., This work was partly sponsored by grant TED2021-131087A-I00 Digital models for the evaluation and reduction of acoustic pollution generated by UAS in urban environments (MODERA) funded by MCIN/AEI/10.13039/501100011033 and by the European Union NextGenerationEU/PRTR.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Tesis de maestría (MasterThesis)

Evaluation of different CFD models for aeroacoustics assessment of low Reynolds number propellers, Evaluation of different CFD models for aeroacoustics assessment of low Reynolds number propellers, Avaluació de diferents models CFD per a l&apos, avaluació aeroacústica d&apos, hèlixs de baix nombre de Reynolds

  • Ramírez, Federico N.|||0000-0003-4525-0516
[ES] Las aeronaves no tripuladas (UAVs) están captando cada vez mayor atención tanto el sector civil como militar debido a sus múltiples ventajas. Se espera que en un futuro cercano la movilidad aérea urbana (UAM) se convierta en una realidad. Debido a esto se están volcando muchos esfuerzos en conseguir herramientas con las cuales diseñar y evaluar correctamente este tipo de vehículos. Una de las principales preocupaciones, ya que podría ser una potencial causa que retrasara el despliegue de UAV en ciudades, es el alto nivel de ruido generado por sus hélices. Aunque existe una extensa cantidad de información en la bibliografía sobre el comportamiento tanto aerodinámico como acústico de hélices, estos estudios se han limitado tradicionalmente a hélices trabajando a alto número de Reynolds, por lo que sus resultados no son directamente extrapolables a las hélices de pequeños UAVs. En este trabajo se utilizará la mecánica de fluidos computacional (CFD) para modelar tanto las actuaciones aerodinámicas como la huella acústica de una hélice a bajo número de Reynolds. Se realizarán simulaciones con distintos niveles de fidelidad con el objetivo de comparar los resultados de los modelos entre sí y con medidas experimentales realizadas tanto en una cámara anecoica como en túnel de viento. De esta forma se evaluará la validez de cada método y se identificará un conjunto de buenas prácticas a seguir para capturar correctamente la acústica de hélices a bajo número de Reynolds., [EN] Unmanned aerial vehicles (UAVs) are receiving increasing attention in both the civil and military sectors due to their multiple advantages. It is expected that in the near future urban air mobility (UAM) will become a reality. Due to this, a lot of effort is being invested in developing tools with which to properly design and evaluate such vehicles. One of the main concerns, which might be a potential delaying cause for the deployment of UAVs in cities, is the high level of noise generated by their propellers. Although there is an extensive bibliography available on the aerodynamic and acoustic performance of propellers, these studies have traditionally been limited to high Reynolds number propellers, so their results are not directly extrapolable to small UAV propellers. In this work, computational fluid mechanics (CFD) will be used to model both the aerodynamic performances and the acoustic footprint of a propeller at low Reynolds number. Simulations will be performed with different levels of fidelity in order to compare the results between models and with experimental measurements performed both in an anechoic chamber and in a wind tunnel. Thus, the validity of each method will be evaluated and a set of good practices for correctly capturing low Reynolds number propeller acoustics will be identified., This work has been developed within the framework of the National Project TED2021-131087A-I00 Digital models for the evaluation and reduction of acoustic pollution generated by UAS in urban environments (MODERA) funded by MCIN/AEI/10.13039/501100011033 and by the European Union NextGenerationEU/PRTR.