Pasar al contenido principal

SUPERACION DE LIMITES TERMOFLUIDODINAMICOS EN MICRO-MOTORES DIESEL PARA VEHICULOS HIBRIDOS ENCHUFABLES

TRA2010-16205

•
Nombre agencia financiadora Ministerio de Ciencia e Innovación
Acrónimo agencia financiadora MICINN
Programa Programa Nacional de Proyectos de Investigación Fundamental
Subprograma Subprograma de Proyectos de Investigación Fundamental no Orientada
Convocatoria Proyectos I+D
Año convocatoria 2010
Plan Estatal 2008-2011 Plan Nacional de Investigación Científica, Desarrollo e Innovación Tecnológica
Unidad de gestión Subdirección General de Proyectos de Investigación
Centro beneficiario UNIVERSITAT POLITÈCNICA DE VALÈNCIA
Identificador persistente http://dx.doi.org/10.13039/501100004837

Resultados relacionados

Resultados totales (Incluyendo duplicados): 9
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Set-up analysis and Optimization of CFD Simulations for Radial Turbines

  • Galindo, José|||0000-0001-6068-182X
  • Hoyas, Sergio|||0000-0002-8458-7288
  • Navarro, Roberto|||0000-0003-2587-4954
  • Fajardo, Pablo
[EN] This paper proposes a CFD method for simulating radial turbocharger turbine flows. A review is presented of the computational model in terms of meshing, mesh movement strategy, and computational algorithm in turbomachinery CFD simulations. A novel local mesh independence analysis is developed for this purpose. This procedure is aimed at distributing the cells more efficiently by selecting suitable cell sizes for the different regions of the domain to optimize the use of the available computational resources. Pressure- and density-based solvers are compared. The influence of the moving-mesh strategy was analyzed, and small differences were observed in the region near the maximum efficiency point, while these differences increased when off-design conditions were considered. Finally, a comparison of the results with data from an experimental test bench shows that the proposed computational methodology can be used to characterize radial turbomachinery. The objective of the analysis and the optimization of the case configuration was to establish some general guidelines for CFD turbomachinery simulations., The authors are indebted to the Spanish Ministerio de Econom a y Competitividad through Project TRA 2010-16205.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Development of a Segregated Compressible Flow Solver for Turbomachinery Simulations

  • Benajes, Jesús|||0000-0002-1653-9188
  • Galindo, José|||0000-0001-6068-182X
  • Navarro, Roberto|||0000-0003-2587-4954
  • Fajardo, P.
[EN] A steady multiple reference frame segregated compressible solver and an unsteady sliding mesh one are developed using OpenFOAM® to simulate turbomachinery. For each of the two solvers, governing equations, numerical approach and solver structure are explained. Pressure and energy equation are implemented so as to obtain the best numerical properties, such as the ability to use large time-steps. Sod shock tube test case is used to assess the prediction of compressible phenomena by the transient scheme, which shows proper resolution of compressible waves. Both solvers are used to simulate a turbocharger turbine, comparing their solutions to corresponding ones using ANSYS® Fluent® as a means of validation. The multiple reference frame solver global results quantitatively differ from those computed using ANSYS Fluent, although predicted flow features match. The solution obtained by the sliding mesh solver presents better agreement compared to ANSYS Fluent one., The authors are indebted to the Spanish Ministerio de Economía y Competitividad through Project TRA 2010-16205.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A stochastic method for the energy management in hybrid electric vehicles

  • Payri, F.|||0000-0002-3314-4911
  • Guardiola, Carlos|||0000-0002-3150-8566
  • Pla Moreno, Benjamín|||0000-0001-9238-2939
  • Blanco-Rodriguez, David
There are many approaches addressing the problem of optimal energy management in hybrid electric vehicles; however, most of them optimise the control strategy for particular driving cycles. This paper takes into account that the driving cycle is not a priori known to obtain a near-optimal solution. The proposed method is based on analysing the power demands in a given receding horizon to estimate future driving conditions and minimise the fuel consumption while cancelling the expected battery energy consumption after a defined time horizon. Simulations show that the proposed method allows charge sustainability providing near-optimal results. (C) 2014 Elsevier Ltd. All rights reserved., This research has been partially supported by Ministerio de Ciencia e Innovacion through Project TRA2010-16205 uDiesel and by the Conselleria de Educacio Cultura i Esports de la Generalitat Valenciana through Project GV/2103/044 AECOSPH.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Experiments on subcooled flow boiling in I.C. engine-like conditions at low flow velocities

  • Torregrosa, A. J.|||0000-0003-0933-1626
  • Broatch, A.|||0000-0001-9991-1039
  • Olmeda, P.|||0000-0002-3161-0165
  • Cornejo, O.
[EN] Subcooled boiling flow is specially attractive for engine cooling system design, as no essential changes in its architecture are required while it is still possible to take advantage of the highest rates of heat transfer associated with nucleate boiling, mostly at high engine loads. In this paper, experiments on subcooled boiling flow in representative temperature conditions were conducted with a usual engine coolant in the low velocity range, for which little information is available, even if it may be relevant when advanced thermal management strategies are used. The results were analyzed by comparison with a reference Chen-type model which provided reasonable results for relatively low wall temperatures, but with noticeable discrepancies at higher wall temperatures. Analysis of the deviations observed indicated a significant influence of the Prandtl number on the suppression factor, and the inclusion into the model of a first estimate of this effect produced a noticeable improvement in its results, thus suggesting that one such modified additive model may be useful for practical engine cooling applications. (C) 2013 Elsevier Inc. All rights reserved., This work has been supported by Ministerio de Ciencia e Innovacion through Grant TRA2010-16205. O. Cornejo is indebted to Senacyt Panama for their support.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Characterization of a radial turbocharger turbine in pulsating flow by means of CFD and its application to engine modeling

  • Galindo, José|||0000-0001-6068-182X
  • Navarro, Roberto|||0000-0003-2587-4954
  • García-Cuevas González, Luis Miguel|||0000-0001-9340-0617
  • Fajardo, Pablo
This paper presents a numerical study analyzing the effect of pulsating flow in a variable geometry radial inflow turbine. The turbine behavior is analyzed under isentropic pulses, which are similar to those created by a rotating disk in a turbocharger test rig. Three different pulse frequencies (50, 90 and 130 Hz) and two pulse amplitudes (100 and 180 kPa) were considered. Turbine flow was studied throughout the pressure pulsation cycles in a wide range of off-design operating conditions, from low pressure ratio flow detachment to high pressure ratio choked flow. An overall analysis of the phasing of instantaneous mass flow and pressure ratio was first performed and the results show the non-quasi-steady behavior of the turbine as a whole as described in the literature. However, the analysis of the flow in the different turbine components independently gives a different picture. As the turbine volute has greater length and volume than the other components, it is the main source of non-quasi-steadiness of the turbine. The stator nozzles cause fewer accumulation effects than the volute, but present a small degree of hysteretic behavior due to flow separation and reattachment cycle around the vanes. Finally, the flow in the moving rotor behaves as quasi-steady, as far as flow capacity is concerned, although the momentum transfer between exhaust gas and blades (and thus work production and thermal efficiency) is affected by a hysteretic cycle against pressure ratio, but not if blade speed ratio is considered instead. A simple model to simulate the turbine stator and rotor is proposed, based on the results obtained from the CFD computations., The authors are indebted to the Spanish Ministerio de Economia y Competitividad through Project TRA 2010-16205. The proof-reading of the paper was funded by the Universitat Politecnica de Valencia, Spain.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A physically based methodology to extrapolate performance maps of radial turbines

  • Payri, F.|||0000-0002-3314-4911
  • Serrano, J.R.|||0000-0003-0692-3917
  • Fajardo, Pablo
  • Reyes Belmonte, Miguel Ángel
  • Gozalbo Belles, Ricardo
This paper details a physically based methodology to perform an extrapolation of the radial turbine performance maps, both mass flow characteristics and the efficiency curve. This method takes into account a narrow range of experimental data, which is usually the data available when such turbines are part of a turbocharger. Therefore, the extrapolation methodology is especially useful when data from third parties are being used or when the compressor of a turbocharger is used as the turbine brake in a gas stand. The nozzle equation is used to develop an interpolation and extrapolation of the mass flow rate trough the turbine. Then, specific information is extracted from this extrapolation and is fed into a total-to-static efficiency equation to carry out an extension of the efficiency curve. This equation is developed using the definition of the total-to-static efficiency, velocity triangles and thermodynamic and fluid fundamental equations. This procedure has been applied to five radial turbines of different sizes and types. Results are compared against experimental information available in the literature or provided by the turbine manufacturers and a good agreement has been found between theoretical and experimentally estimated data. © 2011 Elsevier Ltd. All rights reserved., The authors wish to thank the economical support for this work to Spanish Grant TRA2010-16205 from Ministerio de Ciencia e Innovacion. Direccion General de Investigacion y Gestion del Plan Nacional de I+D+i.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Insight into the HEV/PHEV optimal control solution based on a new tuning method

  • Guardiola, Carlos|||0000-0002-3150-8566
  • Pla Moreno, Benjamín|||0000-0001-9238-2939
  • Onori, S.
  • Rizzoni, G.
The paper presents a formulation of the energy management problem for Hybrid Electrical Vehicles and Plug-in Hybrid Electrical Vehicles alike, which permits to consider different cost indexes like fuel consumption, total and primary energy consumption, economic cost or CO2 footprint. In-depth analysis of the problem optimal solution is done by means of the application of the λ-plot method, which also permits the optimal tuning of other implementable control strategies. Such an approach is used to understand the effect of the selected cost index, the regional energetic share, the driving conditions, and for deriving rules for battery sizing., C. Guardiola and B. Pla research has been partially supported by Ministerio de Ciencia e Innovacion through Project TRA2010-16205 uDiesel, and the Universitat Politecnica de Valencia through Grants PAID-00-11 2105 and PAID-00-11 2106.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Development and validation of a radial variable geometry turbine model for transient pulsating flow applications

  • Galindo, José|||0000-0001-6068-182X
  • Tiseira, Andrés-Omar|||0000-0001-9472-2386
  • García-Cuevas González, Luis Miguel|||0000-0001-9340-0617
  • Fajardo, P.
This paper presents the development and validation of a one-dimensional radial turbine model able to be used in automotive turbocharger simulations. The model has been validated using results from a numerical 3D CFD simulation of stationary and pulsating flow in a variable geometry radial turbine. As the CFD analysis showed, the main non-quasi-steady behavior of the turbine is due to the volute geometry, so special care was taken in order to properly model it while maintaining low computational costs. The flow in the volute has been decomposed in its radial and azimuthal direction. The azimuthal flow corresponds to the flow moving along the volute, while the radial flow is computed by coupling its flow with a stator model. Although the stator caused fewer accumulation effects than the volute, a small accumulation model has been used for it, which also allows to compute the evolution of the flow inside the turbine with lower costs. The flow in the moving rotor can be considered quasi-steady, so a zero-dimensional model for the rotor has been developed. Several losses models where implemented for both the stator and the rotor. The results show good agreement with the CFD computations. 2014 Elsevier Ltd. All rights reserved., The authors are indebted to the Spanish Ministerio de Economia y Competitividad through Project TRA 2010-16205.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Study of the turbocharger shaft motion by means of infrared sensors

  • Serrano, J.R.|||0000-0003-0692-3917
  • Guardiola, Carlos|||0000-0002-3150-8566
  • Dolz-García, Vicente Manuel
  • López, M.A.
  • Bouffaud, F.
This work describes a technique for measuring the precession movement of the shaft of small automotive turbochargers. The main novelty is that the technique is based on infrared light diode sensors. With presented technique it is possible to perform secure mounting of electronics and also to measure, with good accuracy, far enough from the turbocharger shaft. Both advantages allow applying it even in critical lubrication conditions and when blade contact occurs. The technique's main difficulties arise from the small size of the turbocharger shaft and the high precession movement in critical conditions. In order to generate the optimum albedo reflection for infrared measurement, a special cylindrical nut with larger diameter than the original one is assembled at the shaft tip in the compressor side. Following, shaft balancing, the calibration of the sensors and the compensation of errors from different sources are needed steps before the method is able to identify the main frequencies of shaft motion. Once synchronous and sub-synchronous frequencies have been obtained it is possible to reconstruct the instantaneous position of the shaft to determine its precession movement., This research has also been partially supported by the Programa de Desarrollo del Talento Humano de la Secretaria Nacional de Educacion Superior, Ciencia, Tecnologia e Innovacion del Gobierno Ecuatoriano No. 20100289.