Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 6
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Observador de alta ganancia con zona muerta ajustable para estimar la saturación de agua líquida en pilas de combustible tipo PEM, High gain observer with dynamic deadzone to estimate liquid water saturation in PEM fuel cells

  • Cecilia, A.
  • Costa-Castelló, R.
[EN] In the area of PEM fuel cells, water management remains one of the most challenging issues affecting PEMFC efficiency and lifetime. Liquid water active control and supervision techniques are limited by the absence of online sensors that can estimate the liquid water saturation. For this reason, this work presents the design of a state observer to estimate the cathode catalyst layer's liquid water saturation of an open-cathode PEM fuel cell. The proposed observer is based on High-Gain techniques, and is modified with a dynamic dead-zone which reduces the observer's noise sensibility. The results have been validated through numerical simulation and experiments. It is shown that, in the absence of noise, the proposed observer presents a similar performance than its non dead-zone equivalent. Moreover, in the presence of noise, the dead-zone significantly reduces the estimation error induced by it., [ES] En el campo de las pilas de combustible PEM, la gestión de agua líquida es una de las problemáticas más importantes que afectan a la eficiencia y vida útil del sistema. Las técnicas de control activo y supervisión del agua se ven limitadas por la ausencia de sensores que puedan medir la saturación de agua líquida en línea. Por eso, en este trabajo se presenta el diseño de un observador de estado para la estimación de la saturación de agua líquida en la capa catalizadora del cátodo de una pila de combustible PEM de cátodo abierto. El observador propuesto se basa en técnicas de alta ganancia. Además, se modifica con una función de zona muerta autoajustable con el fin de reducir su sensibilidad al ruido en la medida. Los resultados se han validado mediante simulación numérica y experimentación. Estos muestran que, en ausencia de ruido, el observador propuesto presenta unas prestaciones similares a las de su equivalente sin zona muerta. Además, en presencia de ruido, la zona muerta disminuye significativamente el error de estimación inducido por este., Este proyecto se ha financiado parcialmente por el proyecto DOVELAR (ref. RTI2018-096001-B-C32). Este trabajo se ha realizado con el apoyo de la Agencia Estatal de Investigación española a través del sello de excelencia de María de Maeztu, IRI (MDM-2016-0656). Este trabajo se ha financiado parcialmente por AGAUR of Generalitat de Catalunya a través de la subvención del grupo Advanced Control Systems (SAC) (2017 SGR 482). Este trabajo se ha realizado con el apoyo de ACCIÓ (Operational Program FEDER Catalunya 2014-2020) a través de REFER project (COMRDI15-1-0036-11).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Herramientas para la docencia de control digital en grados de ingeniería, Tools for teaching digital control in engineering degrees

  • Lerma, E.
  • Costa-Castelló, R.
  • Griñó, R.
  • Sanchis, C.
[EN] This work describes a set of teaching materials that have been developed to support the learning of digital control. In particular, it presents a set of interactive tools and the project Duino-Based Learning (DBL) that has been designed to develop experimental practices of digital control using Arduino. In addition, the paper depicts the contents of a digital control course, taught in the framework of an industrial engineering degree, and how the developed tools are used in its teaching., [ES] En este trabajo se describen un conjunto de materiales pedagógicos que han sido desarrollados para dar soporte a la docencia del control digital. En particular, se presentan un conjunto de herramientas interactivas y el proyecto Duino-Based Learning (DBL) pensado para desarrollar prácticas experimentales de control digital utilizando Arduino. Además, se describe el contenido de un curso de control digital, que  se imparte en el marco de una titulación de ingeniería industrial, y como se utilizan las diferentes herramientas desarrolladas en su docencia., El trabajo de E. Lerma ha sido financiado por la donación de Mathworks UPC-I-01523. El trabajo de R. Griñó ha sido parcialmente financiado por el Gobierno de España a través de la Agencia Estatal de Investigación Proyecto DPI2017-85404-P, la Generalitat de Catalunya a través del Proyecto 2017 SGR 872 y la donación de Mathworks UPC-I-01523. El trabajo de R. Costa-Castelló ha sido parcialmente financiado por el Gobierno de España a través de la Agencia Estatal de Investigación Proyecto DOVELAR ref. RTI2018-096001-B-C32 (MCIU/AEI/FEDER, UE) y “María de Maeztu Seal of Excellence to IRI” (MDM-2016-0656), la Generalitat de Catalunya a través del Proyecto 2017 SGR 482 y la donación de Mathworks UPC-I-01523.
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Design of state-feedback controllers for linear parameter varying systems subject to time-varying input saturation

  • Ruiz Royo, Adrián
  • Rotondo, Damiano
  • Morcego Seix, Bernardo
All real-world systems are affected by the saturation phenomenon due to inherent physical limitations of actuators. These limitations should be taken into account in the controller’s design to prevent a possibly severe deterioration of the system’s performance, and may even lead to instability of the closed-loop system. Contrarily to most of the control strategies, which assume that the saturation limits are constant in time, this paper considers the problem of designing a state-feedback controller for a system affected by time-varying saturation limits with the objective to improve the performance. In order to tie variations of the saturation function to changes in the performance of the closed-loop system, the shifting paradigm is used, that is, some parameters scheduled by the time-varying saturations are introduced to schedule the performance criterion, which is considered to be the instantaneous guaranteed decay rate. The design conditions are obtained within the framework of linear parameter varying (LPV) systems using quadratic Lyapunov functions with constant Lyapunov matrices and they consist in a linear matrix inequality (LMI)-based feasibility problem, which can be solved efficiently using available solvers. Simulation results obtained using an illustrative example demonstrate the validity and the main characteristics of the proposed approach., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

An LMI–based heuristic algorithm for vertex reduction in LPV systems

  • Sanjuan Gómez, Adrián
  • Rotondo, Damiano
  • Nejjari Akhi-Elarab, Fatiha
  • Sarrate Estruch, Ramon
The linear parameter varying (LPV) approach has proved to be suitable for controlling many non-linear systems. However, for those which are highly non-linear and complex, the number of scheduling variables increases rapidly. This fact makes the LPV controller implementation not feasible for many real systems due to memory constraints and computational burden. This paper considers the problem of reducing the total number of LPV controller gains by determining a heuristic methodology that combines two vertices of a polytopic LPV model such that the same gain can be used in both vertices. The proposed algorithm, based on the use of the Gershgorin circles, provides a combinability ranking for the different vertex pairs, which helps in solving the reduction problem in fewer attempts. Simulation examples are provided in order to illustrate the main characteristics of the proposed approach., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Design of shifting state-feedback controllers for LPV systems subject to time-varying saturations via parameter-dependent Lyapunov functions

  • Ruiz Royo, Adrián
  • Rotondo, Damiano
  • Morcego Seix, Bernardo
This paper considers the problem of designing a shifting state-feedback controller via quadratic parameter-dependent Lyapunov functions (QPDLFs) for systems subject to symmetric time-varying saturations. By means of the linear parameter varying (LPV) framework and the use of the shifting paradigm and the ellipsoidal invariant theory, it is shown that the solution to this problem can be expressed with linear matrix inequalities (LMIs) which can efficiently be solved via available solvers. Specifically, three hyper-ellipsoidal regions are defined in the state-space domain for ensuring that the control action remains in the linearity region of the actuators where saturation does not occur. Furthermore, the closed-loop convergence speed is regulated online according to the instantaneous saturation limit values through the shifting paradigm concept. The main characteristics of the proposed approach are validated by means of two illustrative examples., This work has been partially funded by the Spanish State Research Agency (AEI) and the European Regional Development Fund (ERFD) through the project SaCoAV (ref. PID2020-114244RB-I00). This work has also been partially funded by AGAUR of Generalitat de Catalunya, Spain through the Advanced Control Systems (SAC) group grant (2017 SGR 482) and by the University of Stavanger, Norway through the project IN-12267. A. Ruiz is also supported by the Secretaria d’Universitats i Recerca de la Generalitat de Catalunya, Spain, the European Social Fund (ESF) and AGAUR under a FI SDUR grant (ref. 2020 FI-SDUR 00097)., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Herramientas para la docencia de control digital en grados de ingeniería, Tools for teaching digital control in engineering degrees

  • Lerma Macaya, Eneko
  • Costa Castelló, Ramon
  • Griñó Cubero, Robert
  • Sanchis, Carlos
En este trabajo se describen un conjunto de materiales pedagógicos que han sido desarrollados para dar soporte a la docencia del control digital. En particular, se presentan un conjunto de herramientas interactivas y el proyecto Duino-Based Learning (DBL) pensado para desarrollar prácticas experimentales de control digital utilizando Arduino. Además, se describe el contenido de un curso de control digital, que  se imparte en el marco de una titulación de ingeniería industrial, y como se utilizan las diferentes herramientas desarrolladas en su docencia., Peer Reviewed, Postprint (published version)