Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 10
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Biomass chemical looping gasification for syngas production using ilmenite as oxygen carrier in a 1.5 kWth unit

  • Condori, Óscar
  • García Labiano, Francisco
  • Diego Poza, Luis F. de
  • Izquierdo Pantoja, María Teresa
  • Abad Secades, Alberto
  • Adánez Elorza, Juan
15 figures, 3 tables.-- © 2020. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, Biomass Chemical Looping Gasification, BCLG, is a promising technology that uses lattice oxygen instead of expensive gaseous oxygen for high quality syngas production without CO2 emissions. In this work, 55 h of continuous operation in a 1.5 kWth BCLG unit using ilmenite as oxygen carrier and pine wood as fuel is reported. A new method for controlling the oxygen used in the syngas production through the control of the oxygen fed into the air reactor was used by first time in BCLG with satisfactory results. This method allows analysing the isolated effect of each one of the operating conditions: gasification temperature, TFR, steam-to-biomass ratio, S/B, and oxygen-to-biomass ratio, λ. This last parameter, λ, was the main factor affecting syngas production efficiency. Considering the high unconverted hydrocarbons usually obtained, a product gas composed by 37–40 % CO2; 27–30% H2; 17–21% CO; 10–12% CH4; and 2–3% C2-C3 with a syngas yield of 0.65 Nm3/kg dry biomass could be obtained for autothermal conditions. Tar generation was in the range 1.4–3.0 g/kg dry biomass (1–2.5 g/Nm3 d.b.), being lower than that reported by other gasification technologies. Despite its high reduction state in BCLG, ilmenite exhibited a good behaviour since remained with high reactivity during operation and no agglomeration problems were produced. However, outward migration of Fe observed in ilmenite decreased lifetime by a half during CLG operation in relation to chemical looping combustion conditions., This work has been supported by the European Union's Horizon 2020 - Research and Innovation Framework Programme under grant agreement No 817841 (Chemical Looping gAsification foR sustAinable production of biofuels - CLARA), and by the AEI/FEDER, UE (ENE2017-89473R)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Syngas production in a 1.5 kWth biomass chemical looping gasification unit using Fe and Mn ores as the oxygen carrier

  • Condori, Óscar
  • Diego Poza, Luis F. de
  • García Labiano, Francisco
  • Izquierdo Pantoja, María Teresa
  • Abad Secades, Alberto
  • Adánez Elorza, Juan
12 figures.-- This article is part of the 2021 Pioneers in Energy Research: Javier Bilbao special issue., Biomass chemical looping gasification (BCLG) uses lattice oxygen from an oxygen carrier instead of gaseous oxygen for high-quality syngas production without CO2 emissions. In this work, the effect of the main operating variables, such as oxygen/biomass ratio (λ), gasification temperature, and steam/biomass ratio (S/B), was investigated using two low-cost materials: a Fe ore and a Mn ore. Oxygen fed to the air reactor for oxidation was used as an effective method for controlling the amount of lattice oxygen used for syngas production. The main variable that affected the process performance and the syngas quality was λ, while the fuel reactor temperature and the S/B ratio had a minor effect. Small performance differences found between the ores can be attributed to different degrees of CH4 and light hydrocarbons reforming in the process. The CO2 content in the syngas was high (40 −43%) under autothermal conditions because the gasification reactions required the heat to be generated by combustion. CH4 contents of around 10% were found in syngas, coming from the unburned or unreformed volatiles. Syngas yields around 0.60 Nm3/kg of dry biomass were found for both ores. Additionally, high biomass conversions (Xb > 94%) and carbon conversion efficiencies (ηcc > 95%) were obtained in all cases, showing the capability of the process of avoiding CO2 emissions to the atmosphere. No agglomeration was found in the bed during the BCLG process, although attrition rates were high, leading to lifetimes of 160 and 300 h for the manganese and iron ores, respectively. Migration of Fe or Mn to the external part of the particle, generating a metal concentrated shell, was observed. Its detachment was responsible for the decrease in the oxygen transport capacity (ROC) of the material with the operating time and the reduced lifetime. The results obtained here allowed the iron ore to be considered as an oxygen carrier suitable for the BCLG process., This work has been supported by the European Union’s Horizon 2020 Research and Innovation Framework Programme under grant Agreement 817841 [Chemical Looping Gasification for Sustainable Production of Biofuels (CLARA)] and the AEI/FEDER, UE (ENE2017-89473R)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Biomass chemical looping gasification for syngas production using LD Slag as oxygen carrier in a 1.5 kWth unit

  • Condori, Óscar
  • García Labiano, Francisco
  • Diego Poza, Luis F. de
  • Izquierdo Pantoja, María Teresa
  • Abad Secades, Alberto
  • Adánez Elorza, Juan
12 figures, 3 tables., Biomass Chemical Looping Gasification (BCLG) is an autothermic gasification process that provides pure syngas for many applications, including liquid biofuels production. Finding low-cost materials that can be used in the process is a key issue, especially when they come from waste. In this sense, LD Slag is a by-product of the steel industry used as an oxygen carrier in Chemical Looping Combustion with good results. This work investigates the use of LD Slag as oxygen carrier in a continuous 1.5 kW BCLG unit. The effect of the main operational variables (temperature, oxygen-to-fuel and steam-to-biomass ratios) and the use of CO instead of steam as gasification agent were analysed. LD slag allowed the process with high biomass conversions, X > 90%, carbon conversion efficiencies, η > 90%, and syngas yields, Y ≈ 0.66 Nm/kg of dry biomass, at conditions corresponding to autothermal operation. A lifetime of 300 h under reducing conditions was inferred and agglomeration problems were never detected. LD slag can be considered a suitable material for BCLG since it is possible to obtain high-quality syngas at autothermal conditions from different types of biomass with low tar generation and CO emissions., This work has been supported by the European Union’s Horizon 2020-Research and Innovation Framework Programme under grant agreement No 817841 (Chemical Looping gAsification foR sustainable production of biofuels - CLARA), and by the AEI/FEDER, UE - ENE2017-89473-R.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Assessment of the chemical looping gasification of wheat straw pellets at the 20 kWth scale

  • Condori, Óscar
  • Abad Secades, Alberto
  • Izquierdo Pantoja, María Teresa
  • Diego Poza, Luis F. de
  • García Labiano, Francisco
  • Adánez Elorza, Juan
9 figures, 3 tables.-- Supplementary information available., In this work, the Biomass Chemical Looping Gasification (BCLG) process was evaluated for syngas production at the 20 kWth scale using wheat straw pellets as the fuel feedstock and ilmenite as the oxygen carrier. The effect of different operational variables –namely the fuel reactor temperature, the mean residence time of solids in the fuel reactor, the oxygen-to-biomass ratio (controlled by the oxygen fed into the air reactor) and the gas velocity in the carbon stripper– on the process performance and the syngas yield was analyzed. Interestingly, smooth operation of the CLG unit was observed and no agglomeration issues detected. In addition, char produced during devolatilization still retained its initial pellet shape and unconverted char pellets were elutriated from the fuel reactor mixed with the finer oxygen carrier particles. Both steady-state and transition periods were evaluated to have a complete overview of the process. Transition periods were characterized by a different oxygen transfer rate in the air and fuel reactors. Steady state was reached when the oxygen transference rate was the same in both reactors. In this sense, the oxygen transference rate in the fuel reactor was the main factor affecting the syngas yield and the cold gas efficiency. Also, the temperature and mean residence time of solids in the fuel reactor showed a considerable effect on the char conversion and, consequently, on the syngas yield. However, operating conditions hardly affected the production of light hydrocarbons (CH4 and C2-C3) and tar, which were maintained roughly constant throughout the experimental campaign., This work has been carried out in the framework of the European Union's Horizon 2020 – Research and Innovation Framework Programme under grant agreement No 817841 (Chemical Looping gsification foR sustainAble production of biofuels – CLARA), and by the AEI/FEDER, UE (ENE2017-89473R)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Parametric evaluation of clean syngas production from pine forest residue by chemical looping gasification at the 20 kWth scale

  • Condori, Óscar
  • Abad Secades, Alberto
  • García Labiano, Francisco
  • Diego Poza, Luis F. de
  • Izquierdo Pantoja, María Teresa
  • Adánez Elorza, Juan
9 figures, 5 tables., In the framework of the EU H2020 CLARA project, jet biofuel production via Fischer-Tropsch synthesis is intended from syngas generated by Biomass Chemical Looping Gasification (BCLG). BCLG is based on the lattice oxygen transference between a solid oxygen carrier and the biofuel to energetically support the biomass gasification. This process produces low tar and nitrogen-free syngas under autothermal conditions, and at the same time includes an intrinsic separation of carbon compounds from nitrogen in air, avoiding future carbon capture costs. This work evaluates the syngas production from pine forest residue (PFR) through the BCLG process with ilmenite as the oxygen carrier. The effects of several key operating variables, including temperature, oxygen-to-biomass ratio and mean residence time of solids, on the performance of the BCLG process were analyzed at 20 kWth scale. The syngas yield depended on the oxygen-to-biomass ratio and improved with the char conversion in the fuel reactor. Temperature and mean residence time of solids in the fuel reactor were identified as the primary factors affecting char conversion. A dedicated study was performed to assess the impact of the biomass size on char conversion, as well as the relevance of a carbon stripper unit on the improvement on char gasification due to its role either as a secondary gasifier or as a char-oxygen carrier separator. Higher char conversion values were achieved with the lowest biomass particle size (1–2 mm vs. pellets 6 mm Ø) due to lower restrictions to gas diffusion inside the particles. The carbon stripper may act as a secondary gasifier, thus improving the char conversion, but it was not able to take away the unconverted char particles from ilmenite in any case due to it was designed for powdered fuels. Besides, the generation of light hydrocarbons was hardly affected by any operating variables. The tar content remained below 4.5 g/kg dry biomass. The ilmenite showed a good performance during the continuous operation without signs of defluidization., This work was conducted in the CLARA project (Chemical Looping gAsification foR sustainAble production of biofuels), which is funded by the European Union's Horizon 2020 - Research and Innovation Framework Programme under grant agreement No 817841., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Producción de Syngas a partir de residuos de bosque de pino mediante el proceso CLG en una unidad de 50 kWt

  • Condori, Óscar
  • Abad Secades, Alberto
  • Adánez Elorza, Juan
  • Izquierdo Pantoja, María Teresa
  • de Diego Poza, Luis Francisco
  • García Labiano, Francisco
2 figuras.-- Abstract de la comunicación oral de Tecnologías para la generación sostenible de energía presentada en la XVI Reunión del Grupo Español del Carbón (Reunión GEC 2023), celebrada en Gijón del 22 al 25 de octubre de 2023., El proceso Biomass Chemical-Looping Gasification (BCLG) es una tecnología prometedora e innovadora que permite la producción de un gas de síntesis con bajo contenido de alquitranes y libre de nitrógeno a partir de biomasa. A escala industrial, este proceso opera en condiciones auto-térmicas y no precisa una Unidad de Separación de Aire (ASU) que habitualmente es necesaria en procesos de gasificación convencionales. Además, este proceso implica una separación intrínseca del CO2 y el nitrógeno del aire, evitando emisiones de CO2 a la atmósfera. Por otro lado, siguiendo el concepto de bioenergía con captura y almacenamiento de carbono (BECCS), la combinación del proceso BCLG con el almacenamiento de CO2 tiene el potencial de lograr emisiones netas negativas de CO2 a la atmósfera debido a que las plantas lo absorben a medida que crecen [1]. El proceso BCLG utiliza dos reactores de lecho fluidizado circulante interconectados: un reactor de oxidación (RO) y un reactor de gasificación (RG). La clave del proceso radica en la composición del material de lecho, denominado transportador de oxígeno (TO), que principalmente se basa en óxidos metálicos y se encarga de transportar el oxígeno y el calor necesario para la gasificación de la biomasa desde el RO al RG [2]. El objetivo del estudio es evaluar diversos aspectos que afectan el rendimiento del proceso BCLG en una unidad de 50 kWt en continuo. Entre dichos factores están la temperatura (T), el ratio oxígeno/biomasa (λ) y el tiempo medio de residencia de sólidos en el RG (tmr,RG). Por otro lado, se analizó el impacto del tamaño de partícula de la biomasa y el uso de un separador de carbono (SC) como gasificador secundario., Este trabajo forma parte del proyecto CLARA (Chemical Looping gAsification foR sustainAble production of biofuels), financiado por el Programa Marco de Investigación e Innovación Horizon 2020 de la UE (acuerdo de subvención No 817841)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Effect of biomass torrefaction on the syngas quality produced by Chemical Looping Gasification at 20 kWth scale

  • Condori, Óscar
  • Abad Secades, Alberto
  • Izquierdo Pantoja, María Teresa
  • Diego Poza, Luis F. de
  • Funcia, Ibai
  • Pérez-Vega, Raúl
  • Adánez Elorza, Juan
  • García Labiano, Francisco
9 figures, 5 tables.-- Pusblished as part of virtual special issue “2024 Pioneers in Energy Research: Juan Adanez”., The innovative Biomass Chemical Looping Gasification (BCLG) process uses two reactors (fuel and air reactors) to generate nitrogen-free syngas with low tar content under autothermal conditions. A solid oxygen carrier supplies the oxygen for partial oxidation of the fuel. This study investigated the BCLG process, conducted over 25 h of continuous operation at 20 kWth scale, using ilmenite as the oxygen carrier and wheat straw pellets as fuel (WSP). The effect of using torrefied wheat straw pellets (T-WSP) on the syngas quality was assessed. In addition, the impact of several operational variables on the overall process performance and syngas yield was analyzed. The primary factors influencing the syngas yield were the char conversion through gasification and the oxygen-to-fuel ratio. Higher temperatures, extended residence times of solids in the fuel reactor, and using a secondary gasifier led to increased char conversion, enhancing H2 and CO production. Optimizing the air reactor design could enhance the CO2 capture potential by inhibiting the combustion of bypassed char. While char conversion and syngas yield with T-WSP were lower than those with WSP at temperatures below 900 °C, T-WSP achieved a higher syngas yield under conditions favoring high char conversion. The presence of CH4 and light hydrocarbons showed minimal sensitivity to operating conditions variation, limiting the theoretical syngas yield. Overall, the CLG unit operated smoothly without any agglomeration issues., This study was conducted as part of the European Union’s Horizon 2020─Research and Innovation Framework Programme under grant agreement no. 817841 (Chemical Looping Gasification for Sustainable Production of Biofuels─CLARA) and grant PID2019-106441RB-I00 founded by MCIN/AEI/10.13039/501100011033., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Modeling chemical looping gasification with agroforestry residues: Validation against results in a 20 kWth CLG unit

  • Abad Secades, Alberto
  • Diego Poza, Luis F. de
  • Izquierdo Pantoja, María Teresa
  • Mendiara, Teresa
  • García-Labiano, Francisco
14 figures., Biomass chemical looping gasification (BCLG) represents an innovative process that allows the generation of non-nitrogen-diluted synthesis gas with low tar content and the potential to avoid CO2 emissions. In this work, a 1.5D macroscopic model for the fuel reactor of a BCLG unit was developed and validated to simulate the performance of the system under different operating conditions. The model was developed as simple as possible in order to have a powerful tool to simulate a large number of conditions in a relatively short period of time with low computing effort. However, it has the required complexity to consider the main processes affecting the reaction of the biomass and the oxygen carrier, such as reactor fluid dynamics and the reaction pathway of biomass in the fuel reactor. The main outputs of the model are presented and validated against results from a 20 kWth BCLG unit with two biomasses, namely, pine forest residue and wheat straw pellets. The effects of several operating conditions (temperature, solid circulation rate, solid inventory, and gas flow) on the syngas yield and composition were successfully predicted by the model., This work was supported by the European Union’s Horizon 2020─Research and Innovation Framework Programme under Grant Agreement No. 817841 (Chemical Looping gAsification foR sustainAble production of biofuels─CLARA). The authors thank the funding received from the Gobierno de Aragon through the Combustion and Gasification project (T05_23R)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Designing a 200 MWth biomass chemical looping gasification unit for high-quality syngas production with high CO2 capture rates

  • Abad Secades, Alberto
  • de Diego Poza, Luis Francisco
  • Obras-Loscertales, Margarita de las
  • García Labiano, Francisco
16 figures, 4 tables., Biomass Chemical Looping Gasification (CLG) is a novel process to produce high quality syngas without oxygen requirement while CO2 emission to the atmosphere is avoided. CLG is based on the partial oxidation of the fuel by means of an oxygen carrier, which is continuously regenerated with air by circulating between two interconnected fluidized bed reactors, namely fuel and air reactors. In this work, the design of a 200 MWth CLG unit for syngas production from biomass is presented and optimized after the modelling and simulation of the fuel reactor of this unit. The reactor model was based on a macroscopic fluid dynamic model, and the most relevant chemical processes involving the biomass conversion were included. Modelling results showed that the air to fuel ratio mainly affects the syngas yield, while the fuel reactor temperature affected highly the char conversion. It was shown that the char conversion in a CLG unit does not affect the syngas yield, but rather influences the carbon fraction either oxidized to CO2 or emitted to the atmosphere from the air reactor or captured in the syngas products from the fuel reactor. Main key performance parameters included syngas and hydrocarbons yields of 0.76 and 0.13 S.T.P. m3/kgdry biomass and cold gas efficiency of 73 %., This study was conducted as part of the European Union's Horizon 2020-Research and Innovation Framework Program under grant agreement no. 817841 (Chemical Looping Gasification for Sustainable Production of Biofuels-CLARA). Authors thanks to Grant T05_23R founded by the Government of Aragon., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Determining intrinsic biomass gasification kinetics and its application on gasification of pelletized biomass: simplifying the process for use in chemical looping processes

  • Abad, Alberto
  • Condori, Óscar
  • Diego Poza, Luis F. de
  • García-Labiano, Francisco
This article belongs to the Special Issue Reaction Kinetics in Chemical Looping Processes., The objective of this study was to establish the kinetic of gasification reactions involved in chemical looping gasification (CLG) using pelletized biomass as solid fuel. However, significant limitations have been found in obtaining such kinetics using a traditional methodology from a large number of tests in a thermogravimetric analyzer (TGA) for pelleted biomass. A novel methodology is presented in this article, namely: (i) the determination of the intrinsic gasification rate for several biomasses; (ii) the determination of the gasification rate of pelletized biomass under selected operating conditions; (iii) the development and validation of a reaction model for pelletized biomass considering the determined intrinsic kinetics and gas diffusion in the biomass particles; and (iv) obtaining an apparent kinetics from data calculated with the developed model, which will be easy to implement in the modeling of gasifiers. To evaluate the applicability of this methodology, it was demonstrated with three different types of biomasses: pine forest residue (PFR), industrial wood pellets (IWP), and wheat straw pellets (WSP). The intrinsic kinetics was derived from tests with powdered char under several operating conditions: reacting temperature (1073–1223 K), concentration of gasifying agent (10–40 vol.% H2O or CO2), and concentration of gasification product (0–40 vol.% H2 or CO). The evolution of the char conversion with the reacting time was predicted using a model involving three different regimes: (I) deactivation at the beginning; (II) uniform progress in the main middle part following a n-order model; and (III) catalytic activation as complete conversion is approached. The second regime was included for all biomasses, being 1, 0.4, and zero-order for WSP, IWP, and PFR, respectively. However, the third regime was observed for PFR and IWP, and the first regime only for IWP. The intrinsic kinetics was successfully used in a theoretical model to properly predict the gasification rate of pelletized biomass, and, eventually, to determine an apparent gasification kinetics as simple as possible in order to be easily implemented in future gasifier modeling works., This study was conducted as part of the European Union’s Horizon 2020-Research and Innovation Framework Program under grant agreement no. 817841 (Chemical Looping Gasification for Sustainable Production of Biofuels-CLARA). Authors’ thanks to Grant T05_23R founded by the Government of Aragon., Peer reviewed