Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 18
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Biomass chemical looping gasification for syngas production using ilmenite as oxygen carrier in a 1.5 kWth unit

  • Condori, Óscar
  • García Labiano, Francisco
  • Diego Poza, Luis F. de
  • Izquierdo Pantoja, María Teresa
  • Abad Secades, Alberto
  • Adánez Elorza, Juan
15 figures, 3 tables.-- © 2020. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, Biomass Chemical Looping Gasification, BCLG, is a promising technology that uses lattice oxygen instead of expensive gaseous oxygen for high quality syngas production without CO2 emissions. In this work, 55 h of continuous operation in a 1.5 kWth BCLG unit using ilmenite as oxygen carrier and pine wood as fuel is reported. A new method for controlling the oxygen used in the syngas production through the control of the oxygen fed into the air reactor was used by first time in BCLG with satisfactory results. This method allows analysing the isolated effect of each one of the operating conditions: gasification temperature, TFR, steam-to-biomass ratio, S/B, and oxygen-to-biomass ratio, λ. This last parameter, λ, was the main factor affecting syngas production efficiency. Considering the high unconverted hydrocarbons usually obtained, a product gas composed by 37–40 % CO2; 27–30% H2; 17–21% CO; 10–12% CH4; and 2–3% C2-C3 with a syngas yield of 0.65 Nm3/kg dry biomass could be obtained for autothermal conditions. Tar generation was in the range 1.4–3.0 g/kg dry biomass (1–2.5 g/Nm3 d.b.), being lower than that reported by other gasification technologies. Despite its high reduction state in BCLG, ilmenite exhibited a good behaviour since remained with high reactivity during operation and no agglomeration problems were produced. However, outward migration of Fe observed in ilmenite decreased lifetime by a half during CLG operation in relation to chemical looping combustion conditions., This work has been supported by the European Union's Horizon 2020 - Research and Innovation Framework Programme under grant agreement No 817841 (Chemical Looping gAsification foR sustAinable production of biofuels - CLARA), and by the AEI/FEDER, UE (ENE2017-89473R)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Biomass Chemical Looping Gasification (BCLG) using ilmenite as oxygen carrier

  • García Labiano, Francisco
  • Samprón, Iván
  • Condori, Óscar
  • Adánez Elorza, Juan
  • Diego Poza, Luis F. de
  • Izquierdo Pantoja, María Teresa
Talk delivered at the 6th Central European Biomass Conference, CEBC 2020, 22nd- 24th January 2020, in Graz (Austria)., This work has been supported by the projects ENE2017-89473-R (AEI/FEDER, UE), and CLARA (UE-H2020, No. 817841)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Syngas production in a 1.5 kWth biomass chemical looping gasification unit using Fe and Mn ores as the oxygen carrier

  • Condori, Óscar
  • Diego Poza, Luis F. de
  • García Labiano, Francisco
  • Izquierdo Pantoja, María Teresa
  • Abad Secades, Alberto
  • Adánez Elorza, Juan
12 figures.-- This article is part of the 2021 Pioneers in Energy Research: Javier Bilbao special issue., Biomass chemical looping gasification (BCLG) uses lattice oxygen from an oxygen carrier instead of gaseous oxygen for high-quality syngas production without CO2 emissions. In this work, the effect of the main operating variables, such as oxygen/biomass ratio (λ), gasification temperature, and steam/biomass ratio (S/B), was investigated using two low-cost materials: a Fe ore and a Mn ore. Oxygen fed to the air reactor for oxidation was used as an effective method for controlling the amount of lattice oxygen used for syngas production. The main variable that affected the process performance and the syngas quality was λ, while the fuel reactor temperature and the S/B ratio had a minor effect. Small performance differences found between the ores can be attributed to different degrees of CH4 and light hydrocarbons reforming in the process. The CO2 content in the syngas was high (40 −43%) under autothermal conditions because the gasification reactions required the heat to be generated by combustion. CH4 contents of around 10% were found in syngas, coming from the unburned or unreformed volatiles. Syngas yields around 0.60 Nm3/kg of dry biomass were found for both ores. Additionally, high biomass conversions (Xb > 94%) and carbon conversion efficiencies (ηcc > 95%) were obtained in all cases, showing the capability of the process of avoiding CO2 emissions to the atmosphere. No agglomeration was found in the bed during the BCLG process, although attrition rates were high, leading to lifetimes of 160 and 300 h for the manganese and iron ores, respectively. Migration of Fe or Mn to the external part of the particle, generating a metal concentrated shell, was observed. Its detachment was responsible for the decrease in the oxygen transport capacity (ROC) of the material with the operating time and the reduced lifetime. The results obtained here allowed the iron ore to be considered as an oxygen carrier suitable for the BCLG process., This work has been supported by the European Union’s Horizon 2020 Research and Innovation Framework Programme under grant Agreement 817841 [Chemical Looping Gasification for Sustainable Production of Biofuels (CLARA)] and the AEI/FEDER, UE (ENE2017-89473R)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Biomass chemical looping gasification for syngas production using LD Slag as oxygen carrier in a 1.5 kWth unit

  • Condori, Óscar
  • García Labiano, Francisco
  • Diego Poza, Luis F. de
  • Izquierdo Pantoja, María Teresa
  • Abad Secades, Alberto
  • Adánez Elorza, Juan
12 figures, 3 tables., Biomass Chemical Looping Gasification (BCLG) is an autothermic gasification process that provides pure syngas for many applications, including liquid biofuels production. Finding low-cost materials that can be used in the process is a key issue, especially when they come from waste. In this sense, LD Slag is a by-product of the steel industry used as an oxygen carrier in Chemical Looping Combustion with good results. This work investigates the use of LD Slag as oxygen carrier in a continuous 1.5 kW BCLG unit. The effect of the main operational variables (temperature, oxygen-to-fuel and steam-to-biomass ratios) and the use of CO instead of steam as gasification agent were analysed. LD slag allowed the process with high biomass conversions, X > 90%, carbon conversion efficiencies, η > 90%, and syngas yields, Y ≈ 0.66 Nm/kg of dry biomass, at conditions corresponding to autothermal operation. A lifetime of 300 h under reducing conditions was inferred and agglomeration problems were never detected. LD slag can be considered a suitable material for BCLG since it is possible to obtain high-quality syngas at autothermal conditions from different types of biomass with low tar generation and CO emissions., This work has been supported by the European Union’s Horizon 2020-Research and Innovation Framework Programme under grant agreement No 817841 (Chemical Looping gAsification foR sustainable production of biofuels - CLARA), and by the AEI/FEDER, UE - ENE2017-89473-R.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Otros (Other)

Gasificación de biomasa en una unidad Chemical-Looping de 50 kW utilizando ilmenita como transportador de oxígeno

  • Condori, Óscar
  • Abad Secades, Alberto
  • Adánez Elorza, Juan
  • Diego Poza, Luis F. de
  • Izquierdo Pantoja, María Teresa
  • García Labiano, Francisco
1 figura.-- Resumen de la comunicación oral presentada en la XV Reunión del Grupo Español del Carbón, 24-27 abril 2022, Granada (España).-- O69.-- D.L. GR 695-2022, Una de las opciones más relevantes para la reducción de emisiones de gases de efecto invernadero (GEI) en el sector del transporte es la producción de bio-combustibles sintéticos a partir de gas de síntesis. El proceso Biomass Chemical Looping Gasification (BCLG) es una prometedora opción para producir gas de síntesis de alta calidad mediante la gasificación de biomasa sin emisiones de CO2. En el proceso BCLG un transportador sólido de oxígeno (TO) circula entre dos reactores de lecho fluidizado interconectados, reactor de combustible (RC) y reactor de aire (RA), proporcionanado el oxígeno y el calor necesario para llevar a cabo la oxidación parcial de la biomasa obteniendo un gas de síntesis libre de nitrógeno bajo condiciones autotérmicas. En el RC se produce la gasificación de la biomasa y la combustión parcial de los gases producto con los sólidos, mientras que en el RA se regenera el TO en atmósfera de aire. El objetivo de este trabajo es investigar el efecto de las principales variables operacionales sobre el comportamiento y el rendimiento a gas de síntesis del proceso BCLG en una unidad en continuo de 50 kWt, utilizando ilmenita como TO., Este trabajo ha sido financiado por el Proyecto CLARA de Horizon 2020 European Union funding for Research & Invitation y por el AEI/FEDER, UE-ENE2017-89473R., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Otros (Other)

CLARA WP3 Deliverable D3.3: Results of continuous testing with different fuels and oxygen carriers

  • Soleimani Salim, Amir H.
  • Mattisson, Tobias
  • Adánez Elorza, Juan
  • García Labiano, Francisco
  • Diego Poza, Luis F. de
  • Condori, Óscar
20 figures. 6 tables., Six iron and manganese ores and one by-product from the steel industry was preselected as oxygen carriers for chemical looping gasification (CLG). The selected oxygen carriers have been evaluated at different scales at CTH and CSIC to develop a comprehensive understanding and establish a portfolio of suitable oxygen carriers for CLG. After pre evaluation step in Task 3.1, five oxygen carrier selected for continuous operation in Task 3.3. The selected oxygen carriers from prescreening were Ilmenite, Tierga, LD slag, Elwaleed B, and Moanda. In Task 3.3 a total of 600 hours of continuous CLG operation has been done in 10 kWth reactor at CTH and 1.5 kWth reactor at CSIC. After a vast experimental evaluation at CTH and CSIC, it has been confirmed that using oxygen carrier in CLG has a positive effect on gasification of biomass by reducing tar formation, increasing syngas yield, biomass conversion and H2/CO ratio compare to conventional steam gasification using sand as a bed material. Among the tested oxygen carriers, Ilmenite and LD slag show better biomass gasification performance compared to Mn ores (Elwaleed B and Moanda) and Tierga ore. LD slag has a lower lifetime than ilmenite and needs heat pretreatment, but a slightly higher syngas yield and H2/CO. Therefore, ilmenite has been selected for Task 3.5 and the final demonstration at TUDA (WP5), considering the operational performance, availability of the material at multi-ton scale, lifetime and pretreatments required for the material prior to CLG operation., This project has received funding from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 817841., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Assessment of the chemical looping gasification of wheat straw pellets at the 20 kWth scale

  • Condori, Óscar
  • Abad Secades, Alberto
  • Izquierdo Pantoja, María Teresa
  • Diego Poza, Luis F. de
  • García Labiano, Francisco
  • Adánez Elorza, Juan
9 figures, 3 tables.-- Supplementary information available., In this work, the Biomass Chemical Looping Gasification (BCLG) process was evaluated for syngas production at the 20 kWth scale using wheat straw pellets as the fuel feedstock and ilmenite as the oxygen carrier. The effect of different operational variables –namely the fuel reactor temperature, the mean residence time of solids in the fuel reactor, the oxygen-to-biomass ratio (controlled by the oxygen fed into the air reactor) and the gas velocity in the carbon stripper– on the process performance and the syngas yield was analyzed. Interestingly, smooth operation of the CLG unit was observed and no agglomeration issues detected. In addition, char produced during devolatilization still retained its initial pellet shape and unconverted char pellets were elutriated from the fuel reactor mixed with the finer oxygen carrier particles. Both steady-state and transition periods were evaluated to have a complete overview of the process. Transition periods were characterized by a different oxygen transfer rate in the air and fuel reactors. Steady state was reached when the oxygen transference rate was the same in both reactors. In this sense, the oxygen transference rate in the fuel reactor was the main factor affecting the syngas yield and the cold gas efficiency. Also, the temperature and mean residence time of solids in the fuel reactor showed a considerable effect on the char conversion and, consequently, on the syngas yield. However, operating conditions hardly affected the production of light hydrocarbons (CH4 and C2-C3) and tar, which were maintained roughly constant throughout the experimental campaign., This work has been carried out in the framework of the European Union's Horizon 2020 – Research and Innovation Framework Programme under grant agreement No 817841 (Chemical Looping gsification foR sustainAble production of biofuels – CLARA), and by the AEI/FEDER, UE (ENE2017-89473R)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Syngas production via Biomass Chemical Looping Gasification (BCLG) in a 50 kWth unit using ilmenite as oxygen carrier

  • Condori, Óscar
  • García Labiano, Francisco
  • Diego Poza, Luis F. de
  • Izquierdo Pantoja, María Teresa
  • Abad Secades, Alberto
  • Adánez Elorza, Juan
5 figures, 1 table.-- Talk delivered at the 24th International Conference on Fluidized Bed Conversion, FBC24, at Chalmers University of Technology, in Gothenburg (Sweden)., The use of liquid biofuels is considered one of the most relevant ways to achieve the reduction of greenhouse gas (GHG) emissions in the sector of transport, and more specifically in aviation. A possible route is the use of biogenic waste from the agriculture and forestry sector to obtain synthesis gas via gasification and then the Fischer-Tropsch synthesis to obtain liquid biofuels. Among the different technologies available for the gasification process, Biomass Chemical Looping Gasification (BCLG) represents an innovative process that allows the generation of non-nitrogen diluted synthesis gas under autothermic conditions and with low tars content. By using carbon-neutral biomass as fuel, even net negative emissions could be achieved if the BCLG process is combined with CO2 storage. This work presents an experimental campaign of 40 hours of continuous operation in a 50 kWth BCLG unit developed inside the EU H2020 CLARA Project. Wheat straw pellets with additives were used as fuel feedstock and ilmenite as solid oxygen carrier. This work aimed to investigate the effect of different operational variables such as the fuel reactor temperature, the mean residence time of solids in the fuel reactor, the oxygen-to-biomass ratio (controlled by the oxygen fed into the air reactor) and the gas velocity in the carbon stripper, on the process performance and the syngas yield. Unlike previous studies, effective oxygen-to-biomass ratios that consider the right amount of oxygen that reacts with the oxygen carrier both in the fuel and air reactors (λeff,FR and λeff,AR, respectively) were defined The main factor affecting the syngas yield and the cold gas efficiency was λeff,FR, since it represents the amount of lattice oxygen that actually reacts in the fuel reactor during syngas combustion. However, it showed a low impact on the production of light hydrocarbons (CH4 and C2-C3). The temperature and mean residence time in the fuel reactor showed a considerable effect on the char conversion in the fuel reactor, since an increase in those factors caused an increase in the reaction rates or in the contact time between the oxygen carrier and biomass in the fuel reactor, respectively. Finally, the carbon stripper did not show the ability to separate the solid oxygen carrier from the unconverted char entrained from the fuel reactor, as the char still retained its initial pellet form. Therefore, an increase in gas velocity of carbon stripper promoted the char by-pass to the air reactor, increasing both the biomass conversion in the unit and the fraction of carbon emitted in the air reactor., This work has been supported by the European Union’s Horizon 2020-Research and Innovation Framework Programme under grant agreement No 817841 (Chemical Looping gAsification foR sustainable production of biofuels - CLARA), and by the AEI/FEDER, UE-ENE2017-89473R., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Investigating the chemical looping gasification of biomass for syngas production during continuous operation in 1.5 to 100 kWth units

  • Soleimani Salim, Amir H.
  • Linderholm, Carl
  • Condori, Óscar
  • Samprón, Iván
  • Diego Poza, Luis F. de
  • García Labiano, Francisco
  • Abad Secades, Alberto
  • Adánez Elorza, Juan
  • Mattisson, Tobias
13 figures, 2 tables.-- Talk delivered at the 2nd International Conference on Negative CO2 Emissions, June 14-17, 2022, Göteborg, (Sweden)., The principle of chemical looping has by now mainly been used for the combustion of fuels, i.e. chemical looping combustion (CLC). However, limited work has been done with respect to chemical looping gasification (CLG) of biomass in continuous operation, especially at a large scale. The main advantage of CLG compared to the most common oxygen-driven gasification technologies is the avoidance of an expensive and energy-consuming Air Separation Unit (ASU), which significantly reduces the total investment and the electricity consumption of converting biomass to syngas. In CLG, the produced CO2 is obtained in the concentrated form together with the syngas leaving the fuel reactor, meaning that CO2 can be removed with low energy penalty and subsequently stored in geological formations. When using biomass, storage of CO2 could result in the removal of CO2 from the atmosphere, thus leading to net negative CO2 emissions of the entire process chain for biofuel production. In addition, in comparison to normal indirect gasification, no fuel is used in the air/combustion reactor, meaning that high-temperature corrosion should be avoided to a large extent. Finally, oxygen carrier particles may provide catalytic sites for hydrocarbons, thus enhancing syngas production and suppressing tar formation. The objectives of the EU-financed H2020 project “CLARA” are to develop and test a concept for the gasification of biomass residues with the production of FT-diesel. CLG is the gasification technology which is utilized for syngas production. The main research with respect to CLG development is carried out at Chalmers University of Technology (CTH), Sweden and Consejo Superior de Investigaciones Científicas (CSIC), Spain. The work combines studies in small fixed and fluidized bed units where important results can be reached, with moderate efforts and larger units providing additional key results of industrial relevance. As the final aim is to use CLG at a commercial scale for the production of syngas, it is expected that oxygen carriers at multi-ton scale will be needed. This means that likely only natural or waste materials can be used as oxygen carriers, for instance, Mn- and Fe-ores. An extensive effort has been made to source materials that are available at a large scale. Evaluation of preselected oxygen carriers, using viable fuels, has been carried out in pilot plants in 1.5 kWth, 10 kWth, , 50 kWth, and 100 kWth. The selected oxygen carriers from pre-screening step were (a) Ilmenite, an iron-titanium ore, (b) Tierga iron ore, (c) LD slag, a by-product from steel making industry, and two manganese ores (d) Elwaleed B, and (e) Moanda. For evaluation of these selected oxygen carriers, a total of 650 hours of continuous CLG operation has been accomplished in the mentioned units, with very interesting and promising results, which are reported in the current paper. We here demonstrate that CLG has a positive effect on the gasification of biomass by reducing tar formation, increasing syngas yield, biomass conversion and H2/CO ratio compared to conventional steam gasification using sand as bed material. Also, it has been confirmed that the CO2 in the exit stream from FR is in concentrated form, which can be removed with low energy penalty and could result in the removal of CO2 from the atmosphere, thus leading to net negative CO2 emissions. The effect of the main operating parameters in CLG, such as the temperature, the steam-to-biomass ratio, and the oxygen-to-biomass ratio, was fully investigated. Among the tested oxygen carriers, Ilmenite and LD slag showed a better biomass gasification performance compared to Mn ores (Elwaleed B and Moanda) and Tierga ore. LD slag has a lower lifetime than ilmenite and needs heat pre-treatment, but a higher syngas yield and higher H2/CO ratio were achieved with this material., This work has been supported by the European Union’s Horizon 2020-Research and Innovation Framework Programme under grant agreement No 817841 (Chemical Looping gAsification foR sustainable production of biofuels - CLARA)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Syngas production via Biomass Chemical Looping Gasification (BCLG) in a 50 kWth unit using ilmenite as oxygen carrier

  • Condori, Óscar
  • Abad Secades, Alberto
  • Izquierdo Pantoja, María Teresa
  • Diego Poza, Luis F. de
  • García Labiano, Francisco
  • Adánez Elorza, Juan
8 figures, 1 table.--Talk delivered at the 6th International Conference on Chemical Looping, 19-22 September 2022, Zaragoza, Spain., Biomass Chemical Looping Gasification (BCLG) is an innovative process that uses lattice oxygen from a solid oxygen carrier to produce high-quality synthesis gas without CO2 emissions. It is well known that one of the main targets for the reduction of greenhouse gas emissions (GHG) is to replace the use of fossil fuels in the transport sector with renewable sources. In this work, the BCLG technology is used to obtain clean synthesis gas from biomass for the production of liquid biofuels through Fischer Tropsch (FT) synthesis. The BCLG process is based on the circulation of a solid oxygen carrier between two interconnected fluidized bed reactors, the fuel and air reactors, providing the oxygen needed for the partial oxidation of the biomass to generate a non-nitrogen diluted syngas with low tar content. Also, the oxygen carrier is responsible for transporting the heat required for the endothermic reactions occurring in the fuel reactor from the heat generated in the exothermic reactions occurring in the air reactor, thus reaching autothermal conditions. In addition, negative emissions could be achieved by combining this technology with CO2 storage since biomass is a carbon-neutral fuel. The experimental campaign of this work was carried out in a BCLG unit at 18 kWth power during 60 hours of continuous operation with ilmenite as oxygen carrier and wheat straw pellets as fuel. The main factors affecting the syngas production was the oxygen-to-biomass ratio and char conversion. Increasing temperature showed a considerable effect on the char conversion in the fuel reactor since caused an increase in the gasification rate; also, the char conversion was affected by the mean residence time in the fuel reactor. The existing carbon stripper in the CLG unit did not show the ability to separate the unconverted char entrained from the fuel reactor since char still retained its initial pellet form. However, carbon stripper behaves as a secondary gasifier when using steam as fluidizing agent increasing char conversion, syngas yield and carbon capture efficiency. Finally, low tar generation was found during continuous operation, reaching values below 3.5 g/kg of dry biomass., This work has been supported by the European Union’s Horizon 2020-Research and Innovation Framework Programme under grant agreement No 817841 (Chemical Looping gAsification foR sustainable production of biofuels - CLARA), and by the AEI/FEDER, UE-ENE2017-89473-R., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Parametric evaluation of clean syngas production from pine forest residue by chemical looping gasification at the 20 kWth scale

  • Condori, Óscar
  • Abad Secades, Alberto
  • García Labiano, Francisco
  • Diego Poza, Luis F. de
  • Izquierdo Pantoja, María Teresa
  • Adánez Elorza, Juan
9 figures, 5 tables., In the framework of the EU H2020 CLARA project, jet biofuel production via Fischer-Tropsch synthesis is intended from syngas generated by Biomass Chemical Looping Gasification (BCLG). BCLG is based on the lattice oxygen transference between a solid oxygen carrier and the biofuel to energetically support the biomass gasification. This process produces low tar and nitrogen-free syngas under autothermal conditions, and at the same time includes an intrinsic separation of carbon compounds from nitrogen in air, avoiding future carbon capture costs. This work evaluates the syngas production from pine forest residue (PFR) through the BCLG process with ilmenite as the oxygen carrier. The effects of several key operating variables, including temperature, oxygen-to-biomass ratio and mean residence time of solids, on the performance of the BCLG process were analyzed at 20 kWth scale. The syngas yield depended on the oxygen-to-biomass ratio and improved with the char conversion in the fuel reactor. Temperature and mean residence time of solids in the fuel reactor were identified as the primary factors affecting char conversion. A dedicated study was performed to assess the impact of the biomass size on char conversion, as well as the relevance of a carbon stripper unit on the improvement on char gasification due to its role either as a secondary gasifier or as a char-oxygen carrier separator. Higher char conversion values were achieved with the lowest biomass particle size (1–2 mm vs. pellets 6 mm Ø) due to lower restrictions to gas diffusion inside the particles. The carbon stripper may act as a secondary gasifier, thus improving the char conversion, but it was not able to take away the unconverted char particles from ilmenite in any case due to it was designed for powdered fuels. Besides, the generation of light hydrocarbons was hardly affected by any operating variables. The tar content remained below 4.5 g/kg dry biomass. The ilmenite showed a good performance during the continuous operation without signs of defluidization., This work was conducted in the CLARA project (Chemical Looping gAsification foR sustainAble production of biofuels), which is funded by the European Union's Horizon 2020 - Research and Innovation Framework Programme under grant agreement No 817841., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Producción de Syngas a partir de residuos de bosque de pino mediante el proceso CLG en una unidad de 50 kWt

  • Condori, Óscar
  • Abad Secades, Alberto
  • Adánez Elorza, Juan
  • Izquierdo Pantoja, María Teresa
  • de Diego Poza, Luis Francisco
  • García Labiano, Francisco
2 figuras.-- Abstract de la comunicación oral de Tecnologías para la generación sostenible de energía presentada en la XVI Reunión del Grupo Español del Carbón (Reunión GEC 2023), celebrada en Gijón del 22 al 25 de octubre de 2023., El proceso Biomass Chemical-Looping Gasification (BCLG) es una tecnología prometedora e innovadora que permite la producción de un gas de síntesis con bajo contenido de alquitranes y libre de nitrógeno a partir de biomasa. A escala industrial, este proceso opera en condiciones auto-térmicas y no precisa una Unidad de Separación de Aire (ASU) que habitualmente es necesaria en procesos de gasificación convencionales. Además, este proceso implica una separación intrínseca del CO2 y el nitrógeno del aire, evitando emisiones de CO2 a la atmósfera. Por otro lado, siguiendo el concepto de bioenergía con captura y almacenamiento de carbono (BECCS), la combinación del proceso BCLG con el almacenamiento de CO2 tiene el potencial de lograr emisiones netas negativas de CO2 a la atmósfera debido a que las plantas lo absorben a medida que crecen [1]. El proceso BCLG utiliza dos reactores de lecho fluidizado circulante interconectados: un reactor de oxidación (RO) y un reactor de gasificación (RG). La clave del proceso radica en la composición del material de lecho, denominado transportador de oxígeno (TO), que principalmente se basa en óxidos metálicos y se encarga de transportar el oxígeno y el calor necesario para la gasificación de la biomasa desde el RO al RG [2]. El objetivo del estudio es evaluar diversos aspectos que afectan el rendimiento del proceso BCLG en una unidad de 50 kWt en continuo. Entre dichos factores están la temperatura (T), el ratio oxígeno/biomasa (λ) y el tiempo medio de residencia de sólidos en el RG (tmr,RG). Por otro lado, se analizó el impacto del tamaño de partícula de la biomasa y el uso de un separador de carbono (SC) como gasificador secundario., Este trabajo forma parte del proyecto CLARA (Chemical Looping gAsification foR sustainAble production of biofuels), financiado por el Programa Marco de Investigación e Innovación Horizon 2020 de la UE (acuerdo de subvención No 817841)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Effect of biomass torrefaction on the syngas quality produced by Chemical Looping Gasification at 20 kWth scale

  • Condori, Óscar
  • Abad Secades, Alberto
  • Izquierdo Pantoja, María Teresa
  • Diego Poza, Luis F. de
  • Funcia, Ibai
  • Pérez-Vega, Raúl
  • Adánez Elorza, Juan
  • García Labiano, Francisco
9 figures, 5 tables.-- Pusblished as part of virtual special issue “2024 Pioneers in Energy Research: Juan Adanez”., The innovative Biomass Chemical Looping Gasification (BCLG) process uses two reactors (fuel and air reactors) to generate nitrogen-free syngas with low tar content under autothermal conditions. A solid oxygen carrier supplies the oxygen for partial oxidation of the fuel. This study investigated the BCLG process, conducted over 25 h of continuous operation at 20 kWth scale, using ilmenite as the oxygen carrier and wheat straw pellets as fuel (WSP). The effect of using torrefied wheat straw pellets (T-WSP) on the syngas quality was assessed. In addition, the impact of several operational variables on the overall process performance and syngas yield was analyzed. The primary factors influencing the syngas yield were the char conversion through gasification and the oxygen-to-fuel ratio. Higher temperatures, extended residence times of solids in the fuel reactor, and using a secondary gasifier led to increased char conversion, enhancing H2 and CO production. Optimizing the air reactor design could enhance the CO2 capture potential by inhibiting the combustion of bypassed char. While char conversion and syngas yield with T-WSP were lower than those with WSP at temperatures below 900 °C, T-WSP achieved a higher syngas yield under conditions favoring high char conversion. The presence of CH4 and light hydrocarbons showed minimal sensitivity to operating conditions variation, limiting the theoretical syngas yield. Overall, the CLG unit operated smoothly without any agglomeration issues., This study was conducted as part of the European Union’s Horizon 2020─Research and Innovation Framework Programme under grant agreement no. 817841 (Chemical Looping Gasification for Sustainable Production of Biofuels─CLARA) and grant PID2019-106441RB-I00 founded by MCIN/AEI/10.13039/501100011033., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Tesis doctoral (DoctoralThesis)

Producción de gas de síntesis mediante el proceso Biomass Chemical Looping Gasification utilizando transportadores de oxígeno de bajo coste

  • Condori, Óscar
Tesis presentada en el Departamento de Ingeniería Química y del Medio Ambiente de la Universidad de Zaragoza, para optar al grado de Doctor., Entre las diferentes tecnologías emergentes propuestas para la gasificación de biomasa, el proceso Biomass Chemical Looping Gasification (BCLG) representa un método innovador que permite la generación de gas de síntesis de alta calidad con bajo contenido de alquitrán y en condiciones autotérmicas. Su principal ventaja con respecto a la gasificación convencional es que no requiere el uso de O2 puro (costoso) para obtener un gas de síntesis sin diluir en nitrógeno, además de que previene las emisiones de CO2 a la atmósfera. El proceso BCLG utiliza dos reactores de lecho fluidizado interconectados: un reactor de reducción (RR) y un reactor oxidación (RO). Se basa en un mecanismo que emplea un transportador sólido de oxígeno (óxidos metálicos, MexOy) que circula entre ambos reactores y se encarga de transportar oxígeno y calor desde el RO hasta el RR, evitando el contacto directo entre el aire y la biomasa. La biomasa se alimenta al RR donde se descompone en gases volátiles, alquitranes y char. El char se gasifica con el agente gasificante (vapor o CO2), que también actúa como gas fluidizante para el RR. A continuación, ocurre la oxidación parcial de los diferentes gases producidos mediante reacciones gas-sólido con el transportador de oxígeno que se reduce en paralelo. Luego, el transportador de oxígeno reducido circula hasta el RO donde se reoxida con aire para iniciar un nuevo ciclo. La oxidación del transportador de oxígeno es altamente exotérmica lo que incrementa su temperatura permitiendo que a su regreso al RR proporcione el calor necesario para la conversión de la biomasa (proceso endotérmico). Por otro lado, el proceso BCLG ayuda a confinar el carbono de la biomasa en los gases de salida del RR, facilitando la separación del CO2 generado durante el proceso. Inlcuso, si se combina con el concepto de bioenergía con captura y almacenamiento de carbono (BECCS), el proceso BCLG tiene el potencial de alcanzar emisiones negativas de carbono. Durante esta tesis se ha estudiado el proceso BCLG enfocado en la producción de gas de síntesis de alta calidad bajo condiciones autotérmicas, que posteriormente se utilizará para la producción de biocombustibles de segunda generación (combustible para aviación) mediante el proceso de síntesis Fischer-Tropsch (F-T) en el marco del proyecto europeo CLARA. En este caso, la etapa de separación del CO2 podría integrarse durante la limpieza del gas de síntesis previo a la síntesis de los biocombustibles. De esta manera, el proceso BCLG se sitúa como una de las principales alternativas para la descarbonización del sector del transporte. En primer lugar, se evaluaron las características físico-químicas de diversos materiales de bajo coste, como minerales y residuos industriales basados en óxidos de hierro y manganeso, para su posible uso como transportadores de oxígeno en el proceso BCLG. Todos los materiales estudiados mostraron suficiente capacidad de transporte de oxígeno para llevar a cabo la gasificación de biomasa. También se analizó su reactividad frente a los principales gases reductores del proceso, como el H2 (presente en el gas de síntesis) y el CH4 (representativo de los volátiles de la biomasa), mediante análisis termogravimétrico. Los materiales mostraron una mayor reactividad con el H2, destacando especialmente los minerales de manganeso sobre los de hierro. Sin embargo, en cuanto a la reactividad frente al CH4, los materiales basados en Fe obtuvieron mejores resultados, lo que se traduce en una mayor capacidad para convertir la materia volátil, favoreciendo la maximización de la producción de gas de síntesis en el proceso BCLG. Además, se evaluó la resistencia a la atrición de los diferentes materiales, una propiedad clave para su uso en BCLG, dado que este proceso opera utilizando dos reactores de lecho fluidizado interconectados. Esta resistencia se midió utilizando el índice AJI y la resistencia a la rotura de las partículas. Los minerales de Mn-Gabón y Elwaleed B presentaron altos valores de atrición, con índices AJI del 16.8 % y 8.8 %, respectivamente, mientras que la ilmenita y el residuo industrial LD-slag mostraron mejores resultados, con valores de 2.4 % y 4.6 %, respectivamente. Teniendo en cuenta la reactividad de los materiales y su resistencia a la atrición, se seleccionaron la ilmenita, el mineral de Fe de Tierga, el LD-slag y el Mn de Sibelco como los más adecuados para su uso en una planta piloto de 1.5 kWt en operación continua. No obstante, debido a problemas de suministro con el último, se consideró el mineral de Mn de Gabón en su lugar. A continuación, se inició la experimentación en una planta piloto de 1.5 kWt en continuo, donde se estudió el desempeño de los cuatro transportadores de oxígeno seleccionados utilizando astilla de pino como combustible. Se analizó el efecto de diversas condiciones de operación como la temperatura, el ratio oxígeno/biomasa (λ) y el ratio vapor/biomasa (S/B) sobre la eficiencia del proceso BCLG marcada por parámetros como la conversión de biomasa (Xb), la eficiencia de conversión de carbono (ηcc), el rendimiento a gas de síntesis (Ysg) y la eficiencia de gas frío (ηg). Los resultados mostraron que temperaturas más altas mejoraban la conversión de biomasa y la eficiencia de conversión de carbono, mientras que el aumento de λ disminuyó la calidad del gas de síntesis al aumentar la concentración de CO2 y reducir la de CO y H2. Se observó que un mayor ratio S/B aumentó la concentración de H2 y CO2 y disminuyó la del CO. Además, mejoró la Xb y ηcc, aunque con una mínima variación en el rendimiento del gas de síntesis. Adicionalmente, se probaron otros dos tipos de biomasa (cáscara de almendra y hueso de oliva), con rendimientos similares en Xb y minimas diferencias en la composición del gas de síntesis. Además, se estudió el uso de CO2 como agente gasificante, que redujo la generación de alquitrán aunque produjo un gas de síntesis de menor calidad que utilizando vapor, demandando un mayor esfuerzo en la posterior separación del CO2 existente en el gas producto. El análisis de los resultados obtenidos mostró que la ilmenita y el LD-slag destacaron por su mayor rendimiento a gas de síntesis y menor producción de alquitrán, con la ilmenita mostrando la mayor resistencia a la atrición y vida útil, mientras que el mineral de Mn-Gabón tuvo los peores resultados en ambos aspectos. Así, la ilmenita y el LD-slag fueron los más prometedores para futuras pruebas a mayor escala. En este punto de la tesis se dio inicio a la campaña experimental en una planta piloto BCLG de 20 kWt utilizando ilmenita como transportador de oxígeno. Este material fue seleccionado por su buen desempeño en los ensayos previos a menor escala y a su mayor facilidad para su disponibilidad para los ensayos en el laboratorio en ese instante., Los resultados obtenidos mostraron la importancia de tres variables operativas clave para el proceso: la temperatura, el tiempo medio de residencia de los sólidos (tmr,RR) y la relación oxígeno/biomasa (λ). Estas variables tuvieron un papel crucial en la eficiencia del proceso y en el rendimiento a gas de síntesis. La temperatura y el tmr,RR tuvieron un efecto directo sobre la conversión del char (Xchar,RR), que a su vez afectaba de forma directa a diversos parámetros de eficiencia del proceso, como la Ysg y el ηcc. Temperaturas de gasificación más elevadas (> 900 ºC) y tmr,RR más prolongados favorecieron una mayor Xchar,RR, que al mismo tiempo incrementó la Xb, la ηcc y mejoró la eficiencia general del sistema. Por otro lado, se encontró que un aumento de la tranferencia de oxígeno en el RR (λRR) favoreció la combustión del gas de síntesis, aumentando la producción de CO2 y en consecuencia reduciendo las concentraciones de CO y H2. Sin embargo, es importante alcanzar un valor óptimo para lograr un proceso autotérmico con la mayor calidad del gas de síntesis. Por otra parte, el aumento de λRR no afectó a la producción de hidrocarburos ligeros (CH4 y C2-C3) debido a la baja reactividad de la ilmenita con este tipo de compuestos. El destino de los compuestos de carbono presentes en la biomasa también se vio afectado por las condiciones de operación. Condiciones con baja Xchar,RR (temperatura y tmr,RR bajos) produjeron acumulación del char en el RR, que se vio arrastrado junto con el transportador de oxígeno hasta el RO donde se quemó en contacto con el aire y generó emisiones de CO2 a la atmósfera. Esto evidenció que el Separador de Carbono (SC) no fue capaz de separar el char pelletizado de la ilmenita debido al mayor tamaño de las partículas de char. Sin embargo, el uso de vapor en este dispositivo mejoró significativamente la Xchar,RR ya que actuaba como un gasificador secundario. También se observó la importancia del diseño del RO y de los sifones para optimizar y mejorar la operación y el manejo de la planta. Durante la experimentación en la planta de 20 kWt, también se estudió el comportamiento de la ilmenita con diferentes tipos de biomasa. Se observó una mayor reactividad en los pellets de paja de trigo comparados con el residuo de bosque de pino, lo que resultó en una mayor Xchar,RR. No obstante, las diferencias en la producción de gas de síntesis entre ambos tipos de biomasa fueron pequeñas, y la generación de hidrocarburos ligeros se mantuvo constante, independientemente del tipo de biomasa. Otro factor estudiado fue el efecto del pretratamiento de la biomasa mediante torrefacción, donde se disminuye la humedad y el contenido de volátiles en el combustible. En este caso, la temperatura tuvo mayor influencia sobre el proceso y se lograron mejores rendimientos a mayor temperatura. Además, se estudió el efecto del tamaño de la biomasa mediante el uso de pellets de residuo de bosque de pino molidos. Esto mejoró significativamente la Xchar,RR, debido a una mayor velocidad de gasificación del char causada por una menor resistencia a la difusión interna. También aumentó la producción de hidrocarburos ligeros respecto a los pellets enteros, posiblemente por un incremento en la velocidad de desvolatilización, lo que pudo dificultar el contacto entre los volátiles y las partículas de transportador de oxígeno. Por otro lado, se evaluó la generación de alquitranes durante la experimentación en la planta de 20 kWt, teniendo en cuenta el tipo de biomasa, el tamaño de particula del combustible y su pretratamiento mediante torrefacción. La cantidad y composición de los alquitranes generados dependieron principalmente del tipo de biomasa y su pretratamiento, consiguiendo valores totales siempre por debajo de los obtenidos en procesos de gasificación convencional. La paja de trigo sin torrefactar generó benceno como compuesto mayoritario, con la presencia de naftaleno y tolueno en menor medida, alcanzando un contenido total de alquitrán de hasta 3.5 g/kg de biomasa seca, mientras que la torrefacción mejoró la calidad del gas de síntesis reduciendo el contenido de alquitrán hasta 2 g/kg b.s. El residuo de bosque de pino generó principalmente naftaleno y una menor cantidad de benceno y acenaftileno, con un contenido total de hasta 4.5 g/kg b.s. En este caso, el tamaño de particula de la biomasa apenas tuvo influencia sobre la generación de alquitrán. Se analizó el impacto del régimen de fluidización del RR comparando los resultados obtenidos en las dos plantas piloto (1.5 y 50 kWt) con ilmenita como transportador de oxígeno y madera/residuo de pino como combustible. A menor escala (régimen burbujeante), el tiempo de residencia en el RR, tmr,RR, es mayor que en la planta de 20 kWt (régimen turbulento). lo que facilitó obtener mayores valores de Xchar,RR. El diseño del RO también influyó en la eficiencia del proceso, sugiriendo la necesidad de su optimización en futuros diseños para minimizar la cantidad de oxígeno que reacciona con parte del char que pudiese alcanzar dicho reactor. A pesar de estas variaciones, ambas plantas mostraron rendimientos a gas de síntesis similares, aunque la planta de 20 kWt logró una mejor conversión de hidrocarburos ligeros (CH4 y C2-C3), probablemente debido a un mayor tiempo de residencia del gas en el RR y mejor interacción entre el gas y los sólidos gracias al régimen turbulento. Por último, se analizó la integridad física de la ilmenita y la posible interacción con las cenizas presentes en la paja de trigo. Tras 40 horas de operación continua en condiciones BCLG, la ilmenita no mostró signos de aglomeración ni problemas de fluidización. Esto confirmó la efectividad de los aditivos presentes en los pellets de paja para prevenir la aglomeración. Sin embargo, un análisis más exhaustivo mostró que el Ca, K y Si (presentes en las cenizas) se concentraban en la superficie externa de las partículas de ilmenita llegando incluso al interior de la grietas. Las partículas de ilmenita presentaron un ligero desgaste consecuencia de la migración del Fe hacia el exterior de las partículas donde se formaba una capa que posteriormente se desprendía. Esto se reflejó en una pérdida de la capacidad de transporte de oxígeno, aunque la reactividad no se vió afectada. En términos generales la ilmenita mostró un buen desempeño y una buena resistencia a la atrición., Esta tesis se desarrolló entre los años 2019 y 2024 en el Instituto de Carboquímica (ICB) de Zaragoza, perteneciente al Consejo Superior de Investigaciones Científicas (CSIC). El trabajo fue realizado gracias a la financiación del Programa de Investigación e Innovación Horizonte 2020 de la Unión Europea, en virtud del acuerdo de subvención nº 817841 (Chemical Looping Gasification for Sustainable Production of Biofuels – CLARA). La investigación también contó con el apoyo financiero parcial de la Agencia Estatal de Investigación del Ministerio español de Ciencia e Innovación, mediante las subvenciones de los proyectos ENE2017-89473-R/AEI/FEDER, UE y PID2019-106441RB-I00, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Modeling chemical looping gasification with agroforestry residues: Validation against results in a 20 kWth CLG unit

  • Abad Secades, Alberto
  • Diego Poza, Luis F. de
  • Izquierdo Pantoja, María Teresa
  • Mendiara, Teresa
  • García-Labiano, Francisco
14 figures., Biomass chemical looping gasification (BCLG) represents an innovative process that allows the generation of non-nitrogen-diluted synthesis gas with low tar content and the potential to avoid CO2 emissions. In this work, a 1.5D macroscopic model for the fuel reactor of a BCLG unit was developed and validated to simulate the performance of the system under different operating conditions. The model was developed as simple as possible in order to have a powerful tool to simulate a large number of conditions in a relatively short period of time with low computing effort. However, it has the required complexity to consider the main processes affecting the reaction of the biomass and the oxygen carrier, such as reactor fluid dynamics and the reaction pathway of biomass in the fuel reactor. The main outputs of the model are presented and validated against results from a 20 kWth BCLG unit with two biomasses, namely, pine forest residue and wheat straw pellets. The effects of several operating conditions (temperature, solid circulation rate, solid inventory, and gas flow) on the syngas yield and composition were successfully predicted by the model., This work was supported by the European Union’s Horizon 2020─Research and Innovation Framework Programme under Grant Agreement No. 817841 (Chemical Looping gAsification foR sustainAble production of biofuels─CLARA). The authors thank the funding received from the Gobierno de Aragon through the Combustion and Gasification project (T05_23R)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Research data Set de datos (Dataset)

Supporting information for Modelling chemical looping gasification with agroforestry residues: validation against results in a 20 kWth CLG unit [Dataset]

  • Abad Secades, Alberto
  • Diego Poza, Luis F. de
  • Izquierdo Pantoja, María Teresa
  • Mendiara, Teresa
  • García-Labiano, Francisco
Under a Creative Commons BY 4.0 license., The mathematical model developed is focused on the fuel reactor behaviour of a 20 kWth Biomass Chemical Looping Gasification (BCLG) unit at ICB-CSIC, which has been operated with ilmenite being the oxygen carrier and wheat straw pellets (WSP) or pine forest residue (PFR) being the fuels.S1,S2 The model includes the main processes affecting to the reaction of the biomass and the oxygen carrier, such as reactor fluid dynamics and the reaction pathway of biomass in the fuel reactor., This work was supported by the European Union’s Horizon 2020─Research and Innovation Framework Programme under Grant Agreement No. 817841 (Chemical Looping gAsification foR sustainAble production of biofuels─CLARA). The authors thank the funding received from the Gobierno de Aragon through the Combustion and Gasification project (T05_23R)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Designing a 200 MWth biomass chemical looping gasification unit for high-quality syngas production with high CO2 capture rates

  • Abad Secades, Alberto
  • de Diego Poza, Luis Francisco
  • Obras-Loscertales, Margarita de las
  • García Labiano, Francisco
16 figures, 4 tables., Biomass Chemical Looping Gasification (CLG) is a novel process to produce high quality syngas without oxygen requirement while CO2 emission to the atmosphere is avoided. CLG is based on the partial oxidation of the fuel by means of an oxygen carrier, which is continuously regenerated with air by circulating between two interconnected fluidized bed reactors, namely fuel and air reactors. In this work, the design of a 200 MWth CLG unit for syngas production from biomass is presented and optimized after the modelling and simulation of the fuel reactor of this unit. The reactor model was based on a macroscopic fluid dynamic model, and the most relevant chemical processes involving the biomass conversion were included. Modelling results showed that the air to fuel ratio mainly affects the syngas yield, while the fuel reactor temperature affected highly the char conversion. It was shown that the char conversion in a CLG unit does not affect the syngas yield, but rather influences the carbon fraction either oxidized to CO2 or emitted to the atmosphere from the air reactor or captured in the syngas products from the fuel reactor. Main key performance parameters included syngas and hydrocarbons yields of 0.76 and 0.13 S.T.P. m3/kgdry biomass and cold gas efficiency of 73 %., This study was conducted as part of the European Union's Horizon 2020-Research and Innovation Framework Program under grant agreement no. 817841 (Chemical Looping Gasification for Sustainable Production of Biofuels-CLARA). Authors thanks to Grant T05_23R founded by the Government of Aragon., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Determining intrinsic biomass gasification kinetics and its application on gasification of pelletized biomass: simplifying the process for use in chemical looping processes

  • Abad, Alberto
  • Condori, Óscar
  • Diego Poza, Luis F. de
  • García-Labiano, Francisco
This article belongs to the Special Issue Reaction Kinetics in Chemical Looping Processes., The objective of this study was to establish the kinetic of gasification reactions involved in chemical looping gasification (CLG) using pelletized biomass as solid fuel. However, significant limitations have been found in obtaining such kinetics using a traditional methodology from a large number of tests in a thermogravimetric analyzer (TGA) for pelleted biomass. A novel methodology is presented in this article, namely: (i) the determination of the intrinsic gasification rate for several biomasses; (ii) the determination of the gasification rate of pelletized biomass under selected operating conditions; (iii) the development and validation of a reaction model for pelletized biomass considering the determined intrinsic kinetics and gas diffusion in the biomass particles; and (iv) obtaining an apparent kinetics from data calculated with the developed model, which will be easy to implement in the modeling of gasifiers. To evaluate the applicability of this methodology, it was demonstrated with three different types of biomasses: pine forest residue (PFR), industrial wood pellets (IWP), and wheat straw pellets (WSP). The intrinsic kinetics was derived from tests with powdered char under several operating conditions: reacting temperature (1073–1223 K), concentration of gasifying agent (10–40 vol.% H2O or CO2), and concentration of gasification product (0–40 vol.% H2 or CO). The evolution of the char conversion with the reacting time was predicted using a model involving three different regimes: (I) deactivation at the beginning; (II) uniform progress in the main middle part following a n-order model; and (III) catalytic activation as complete conversion is approached. The second regime was included for all biomasses, being 1, 0.4, and zero-order for WSP, IWP, and PFR, respectively. However, the third regime was observed for PFR and IWP, and the first regime only for IWP. The intrinsic kinetics was successfully used in a theoretical model to properly predict the gasification rate of pelletized biomass, and, eventually, to determine an apparent gasification kinetics as simple as possible in order to be easily implemented in future gasifier modeling works., This study was conducted as part of the European Union’s Horizon 2020-Research and Innovation Framework Program under grant agreement no. 817841 (Chemical Looping Gasification for Sustainable Production of Biofuels-CLARA). Authors’ thanks to Grant T05_23R founded by the Government of Aragon., Peer reviewed