Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 12
Encontrada(s) 1 página(s)

Repositori Obert UdL
Publication Artículo científico (JournalArticle)

A technical and economic comparison between concrete and latent thermal energy storage for concentrated solar power applications

  • Prieto, Cristina
  • Borri, Emiliano
  • Pavón Moreno, M. Carmen
  • Zsembinszki, Gabriel
  • Cabeza, Luisa F.
Thermal energy storage (TES) plays a key role in concentrating solar power (CSP) plants by enhancing dispatchability and improving overall system efficiency. This study presents a comparative techno-economic analysis of three TES configurations integrated into CSP plants: (i) the conventional two-tank molten salt system, (ii) a phase change material (PCM)-based system with a cascade arrangement, and (iii) a concrete-based system. While technical performance simulations indicate similar annual energy production across all cases, significant differences emerge in economic viability. The PCM TES system demonstrates the lowest levelized cost of electricity (LCoE) at $14.35/kWh, leveraging its high energy density and reduced material requirements, despite lower efficiency (93 % compared to 99 % in molten salt). Conversely, the concrete TES system, while capable of extended discharge at partial loads, incurs higher parasitic losses and investment costs, resulting in a higher LCoE ($16.16/kWh). The cost analysis further highlights the cost-performance quotient (CPQ) as a valuable metric for assessing TES competitiveness, with PCM exhibiting the most favorable CPQ of $1.04/kWh. These findings underscore the necessity of integrating economic assessments into TES selection for CSP plants. Moreover, the study identifies opportunities for cost reduction in concrete TES through optimized modular designs and improved material formulations. This work provides valuable insights for policymakers, engineers, and industry stakeholders aiming to enhance the financial feasibility of next-generation CSP storage solutions., This study receives funding from the Ministerio de Ciencia e Innovación – Agencia Estatal de Investigación (MCIN/AEI/10.13039/501100011033) through the PCI2020-120695-2 project and the European Union “NextGenerationEU”/PRTR“. CSP-ERA.NET is supported by the European Commission within the EU Framework Programme for Research and Innovation Horizon 2020 (Cofund ERA-NET Action, N° 838311). This work was partially funded by the Ministerio de Ciencia e Innovación de España TED2021-132216A-I00 funded by MCIN/AEI/10.13039/501100011033 and the European Union by NextGenerationEU/PRTR. This work was partially funded by the Ministerio de Ciencia e Innovación – Agencia Estatal de Investigación (AEI) (PID2021-123511OB-C31 – MCIN/AEI/10.13039/501100011033/FEDER, UE) and (RED2022-134219-T). This work is partially supported by ICREA under the ICREA Academia programme. The authors from University of Lleida would like to thank the Departament de Recerca i Universitats of the Catalan Government for the quality accreditation given to their research group (2021 SGR 01615). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia.
Repositori Obert UdL
Publication Artículo científico (JournalArticle)

Advancing sensible heat storage: A novel transient heat transfer model for concrete-based TES modules for CSP applications

  • Tagle-Salazar, Pablo D.
  • Cabeza, Luisa F.
  • Prieto, Cristina
Concentrating solar power (CSP) plays a crucial role in renewable energy systems, offering high-temperature heat for electricity generation and industrial processes while supporting the transition to sustainable energy. Thermal energy storage (TES) improves the reliability and dispatchability of CSP systems. Among the sensible heat storage options, concrete emerges as a cost-effective and eco-friendly alternative that warrants further investigation. This study introduces a comprehensive mathematical model for simulating the transient thermal behaviour of concrete-based TES modules. The model accommodates diverse geometries, supports a wide range of heat transfer fluids (HTFs) in all flow regimes, and accounts for heat losses to the environment, factors that are often overlooked in prior research. The mathematical framework was incorporated into a software platform called OpenModelica and will later be included in a tool developed by the authors to evaluate the performance of CSP plants. Before this integration takes place, the model undergoes validation, which is the primary focus of this study. The model was validated through two case studies, one theoretical and the other experimental, each involving different operational conditions, geometries, HTFs, and materials. The theoretical case confirmed that the model could capture the key physical phenomena governing transient heat transfer in the storage module. A comparison between the simulation results and experimental data revealed a strong agreement in temperature, heat flow, and total energy transmitted, with temperature errors within the IEC 60751 standard and total energy transfer errors ranging from −6.15 % to +5.69 %. These findings highlight the potential of concrete-based TES to enhance the performance of CSP systems, contributing to reliable and sustainable energy solutions., CSP-ERA.NET is supported by the European Commission within the EU Framework Programme for Research and Innovation Horizon 2020 (Cofund ERA-NET Action, N◦ 838311). This study receives funding from the Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (MCIN/AEI/10.13039/501100011033) through the PCI2020-120695-2 project and the European Union “NextGenerationEU"/PRTR”. This work was partially funded by the Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (AEI) (PID2021-123511OB-C31 - MCIN/AEI/ 10.13039/501100011033/FEDER, UE), and by Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (AEI) (RED2024-153629- T). This work is partially supported by ICREA under the ICREA Academia programme. The authors would like to thank the Departament de Recerca i Universitats of the Catalan Government for the quality accreditation given to their research group (2021 SGR 01615). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia.
Repositori Obert UdL
Publication Artículo científico (JournalArticle)

A transient heat losses model for two-tank storage systems with molten salts

  • Tagle-Salazar, Pablo D.
  • Prieto, Cristina
  • López-Román, Antón
  • Cabeza, Luisa F.
Concentrating Solar Power (CSP) is a proven and mature technology for energy supply. In recent years, electricity generation based on this technology has increased worldwide, to a large degree due to its high dispatchability when coupled with an energy storage system. Commercially, most plants store the energy in molten salts in a two-tank configuration. This study focuses on this storage configuration and proposes a mathematical model for the thermal losses in these tanks, both at nominal conditions and during transients. With this model at its core, a computational tool for thermal performance analysis in OpenModelica is developed. This dynamic thermal model includes the estimation of local heat loss due to assembly defects, which are heat flows that cannot be determined by theoretical modelling. The development of a semi-empirical correlation for estimating local heat loss is also presented. Simulation results showed that this local heat loss may represent a share about 40% of the total heat loss in a small-scale tank. A comparison of the characteristics of the model proposed in a previous work is also presented to establish the innovation of the model. Two thermal storage systems with different tank designs and sizes were simulated to compare the results using the present model with data available in the literature. Results show good agreement in transient thermal behaviour of heat flows, temperatures, and cooling rates when compared with data from other authors for the same tank., This project was funded by the European Union's Horizon 2020 Research and Innovation Programme under No. 838311 (CSP plus). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREiA (2021 SGR 01615). GREiA is a certified agent TECNIO in the category of technology developers from the Government of Catalonia. This work was partially funded by the Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (PID2021-123511OB-C31 - MCIN/AEI/10.13039/501100011033/FEDER, EU, TED2021-132216A-I00 and RED2022-134219-T). This work is partially supported by ICREA under the ICREA Academia programme.
Repositori Obert UdL
Publication Artículo científico (JournalArticle)

Transient performance modelling of solar tower power plants with molten salt thermal energy storage systems

  • Tagle-Salazar, Pablo D.
  • Cabeza, Luisa F.
  • Prieto, Cristina
Concentrating solar power (CSP) has emerged as a dynamic and promising technology, demonstrating a burgeoning market potential for power generation through the utilization of solar thermal resources. Notably, global installed capacity has witnessed a substantial uptick in recent years, indicative that this technology is increasing traction worldwide. To optimize the utilization of CSP systems, particularly during periods of low or absent solar radiation, the integration of thermal energy storage (TES) systems using molten salts has become a prevailing strategy. This research introduces an innovative transient modelling tailored for the comprehensive annual performance analysis of a solar tower power plant coupled to a two-tank TES system, incorporating molten salts as the storage medium. The modelling of the power plant is conducted using OpenModelica, a versatile software platform renowned for its capability in system-level modelling and simulation. The simulation outcomes encompass a power plant configuration boasting a turbine gross output of 110 MWe. The results of performance parameters are subsequently contrasted with those generated by commercially available software tool, effectively corroborating the accuracy and effectiveness of the proposed simulation approach. The obtained results demonstrate a favourable concurrence in the transient behaviour of performance parameters, considering heat flows, state of charge, net power, and others, with a discrepancy of less than 1 % in annual production when benchmarked against a commercial software reference. Particularly, the incorporation of the local heat loss due to assembly defects within the thermal modelling of the TES system exerts a discernible albeit relatively minor influence on the overall performance of the power plant. The occurrence of local heat loss primarily stems from distortions or imperfections within the construction, including the structure, insulation layers, or foundation, thereby creating thermal bridges between the storage fluid and the external ambient environment. This impact, while small, is not negligible, as it introduces the potential for the power block to unexpectedly shut down owing to TES system depletion, a behaviour that is challenging to simulate when neglecting local heat loss., CSP-ERA.NET is supported by the European Commission within the EU Framework Programme for Research and Innovation Horizon 2020 (Cofund ERA-NET Action, N° 838311). This study receives funding from the Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (MCIN/AEI/10.13039/501100011033) through the PCI2020-120695-2 project and the European Union “NextGenerationEU”/“PRTR”. This work was partially funded by the Ministerio de Ciencia e Innovación de España TED2021-132216A-I00 funded by MCIN/AEI/10.13039/501100011033 and the European Union by NextGenerationEU/PRTR. This work was partially funded by Ministerio de Ciencia, Innovación y Universidades - Agencia Estatal de Investigación (AEI) (RED2022-134219-T). This work is partially supported by ICREA under the ICREA Academia programme. The authors would like to thank the Departament de Recerca i Universitats of the Catalan Government for the quality accreditation given to their research group (2021 SGR 01615). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia.
Dipòsit Digital de la UB
Publication Artículo científico (JournalArticle)

Assessment of Solid Wastes and By-Products as Solid Particle Materials for Concentrated Solar Power Plants

  • Majó Robles, Marc
  • Calderón Díaz, Alejandro
  • Salgado Pizarro, Rebeca
  • Svobodova Sedlackova, Adela
  • Barreneche, Camila
  • Chimenos Ribera, Josep Ma.
  • Fernández Renna, Ana Inés
The revalorization of solid wastes and by-products to be applied as solid particles in concentrated solar power (CSP) leads to cost savings and progresses toward more sustainable technology. Herein, the physicochemical, morphological, thermal, and solar absorption properties are evaluated for electric arc furnace dust, black slag from the steel industry, and Gossan waste from the Rio Tinto mining industry. The principal objectives of this work are (i) to carry out a thermal aging at 900 °C at different times, (ii) to assess the solid's stability throughout the evaluation of physicochemical, morphological, thermal, and optical properties of the material as received, after 300 and 500 h of thermal aging, and (iii) to determine the most appropriate candidate as a thermal energy storage medium and heat transfer fluid for the CSP concept with solid particles. The results show that electric arc furnace black slag is the most suitable candidate from the three solids studied, as it is the one that optimizes the combination of absorptance, thermal conductivity, and chemical stability after thermal aging.
Dipòsit Digital de la UB
Publication Artículo científico (JournalArticle)

Long-term stability of sensible thermal energy storage materials developed from demolition wastes interacting with hot heat transfer fluid

  • Koçak, Burcu
  • Fernández Renna, Ana Inés
  • Paksoy, Halime O.
Packed-bed thermal energy storage (TES) system filled with low cost and sustainable sensible thermal energy storage material (STESM) is a promising option for medium-high temperature applications. STESM developed from demolition wastes are eco-innovative and compatible with circular economy. They can be used in solar heat industrial applications up to 750°C. One of the main concerns that should be taken into consideration is the stability of STESM developed from demolition wastes in direct contact with hot heat transfer fluids (HTFs). In this study, thermal and mechanical stability of STESM developed from demolition waste were investigated using repeated heating and cooling cycles in Therminol 66 synthetic oil as HTF at 150°C for up to 500 hours. The characterization results before and after thermal cycling showed that new STESM developed from demolition wastes is thermally and mechanically stable. Also, strong oil penetration into the STESM samples improved the porosity, strength, and specific heat capacity. The specific heat capacity and mechanical strength values increased from 1330 to 1490 J/kgC and from 4 to 6 MPa, respectively. These results suggest that STESM samples developed from demolition waste can be used reliably in solar heat industrial applications for long term.
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

A transient heat losses model for two-tank storage systems with molten salts

  • Tagle-Salazar, Pablo D.
  • Prieto, Cristina
  • López-Román, Antón
  • Cabeza, Luisa F.
Concentrating Solar Power (CSP) is a proven and mature technology for energy supply. In recent years, electricity generation based on this technology has increased worldwide, to a large degree due to its high dispatchability when coupled with an energy storage system. Commercially, most plants store the energy in molten salts in a two-tank configuration. This study focuses on this storage configuration and proposes a mathematical model for the thermal losses in these tanks, both at nominal conditions and during transients. With this model at its core, a computational tool for thermal performance analysis in OpenModelica is developed. This dynamic thermal model includes the estimation of local heat loss due to assembly defects, which are heat flows that cannot be determined by theoretical modelling. The development of a semi-empirical correlation for estimating local heat loss is also presented. Simulation results showed that this local heat loss may represent a share about 40% of the total heat loss in a small-scale tank. A comparison of the characteristics of the model proposed in a previous work is also presented to establish the innovation of the model. Two thermal storage systems with different tank designs and sizes were simulated to compare the results using the present model with data available in the literature. Results show good agreement in transient thermal behaviour of heat flows, temperatures, and cooling rates when compared with data from other authors for the same tank., This project was funded by the European Union's Horizon 2020 Research and Innovation Programme under No. 838311 (CSP plus). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREiA (2021 SGR 01615). GREiA is a certified agent TECNIO in the category of technology developers from the Government of Catalonia. This work was partially funded by the Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (PID2021-123511OB-C31 - MCIN/AEI/10.13039/501100011033/FEDER, EU, TED2021-132216A-I00 and RED2022-134219-T). This work is partially supported by ICREA under the ICREA Academia programme.
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Transient performance modelling of solar tower power plants with molten salt thermal energy storage systems

  • Tagle-Salazar, Pablo D.
  • Cabeza, Luisa F.
  • Prieto, Cristina
Concentrating solar power (CSP) has emerged as a dynamic and promising technology, demonstrating a burgeoning market potential for power generation through the utilization of solar thermal resources. Notably, global installed capacity has witnessed a substantial uptick in recent years, indicative that this technology is increasing traction worldwide. To optimize the utilization of CSP systems, particularly during periods of low or absent solar radiation, the integration of thermal energy storage (TES) systems using molten salts has become a prevailing strategy. This research introduces an innovative transient modelling tailored for the comprehensive annual performance analysis of a solar tower power plant coupled to a two-tank TES system, incorporating molten salts as the storage medium. The modelling of the power plant is conducted using OpenModelica, a versatile software platform renowned for its capability in system-level modelling and simulation. The simulation outcomes encompass a power plant configuration boasting a turbine gross output of 110 MWe. The results of performance parameters are subsequently contrasted with those generated by commercially available software tool, effectively corroborating the accuracy and effectiveness of the proposed simulation approach. The obtained results demonstrate a favourable concurrence in the transient behaviour of performance parameters, considering heat flows, state of charge, net power, and others, with a discrepancy of less than 1 % in annual production when benchmarked against a commercial software reference. Particularly, the incorporation of the local heat loss due to assembly defects within the thermal modelling of the TES system exerts a discernible albeit relatively minor influence on the overall performance of the power plant. The occurrence of local heat loss primarily stems from distortions or imperfections within the construction, including the structure, insulation layers, or foundation, thereby creating thermal bridges between the storage fluid and the external ambient environment. This impact, while small, is not negligible, as it introduces the potential for the power block to unexpectedly shut down owing to TES system depletion, a behaviour that is challenging to simulate when neglecting local heat loss., CSP-ERA.NET is supported by the European Commission within the EU Framework Programme for Research and Innovation Horizon 2020 (Cofund ERA-NET Action, N° 838311). This study receives funding from the Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (MCIN/AEI/10.13039/501100011033) through the PCI2020-120695-2 project and the European Union “NextGenerationEU”/“PRTR”. This work was partially funded by the Ministerio de Ciencia e Innovación de España TED2021-132216A-I00 funded by MCIN/AEI/10.13039/501100011033 and the European Union by NextGenerationEU/PRTR. This work was partially funded by Ministerio de Ciencia, Innovación y Universidades - Agencia Estatal de Investigación (AEI) (RED2022-134219-T). This work is partially supported by ICREA under the ICREA Academia programme. The authors would like to thank the Departament de Recerca i Universitats of the Catalan Government for the quality accreditation given to their research group (2021 SGR 01615). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia.
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Long-term stability of sensible thermal energy storage materials developed from demolition wastes interacting with hot heat transfer fluid

  • Koçak, Burcu
  • Fernández Renna, Ana Inés
  • Paksoy, Halime O.
Packed-bed thermal energy storage (TES) system filled with low cost and sustainable sensible thermal energy storage material (STESM) is a promising option for medium-high temperature applications. STESM developed from demolition wastes are eco-innovative and compatible with circular economy. They can be used in solar heat industrial applications up to 750°C. One of the main concerns that should be taken into consideration is the stability of STESM developed from demolition wastes in direct contact with hot heat transfer fluids (HTFs). In this study, thermal and mechanical stability of STESM developed from demolition waste were investigated using repeated heating and cooling cycles in Therminol 66 synthetic oil as HTF at 150°C for up to 500 hours. The characterization results before and after thermal cycling showed that new STESM developed from demolition wastes is thermally and mechanically stable. Also, strong oil penetration into the STESM samples improved the porosity, strength, and specific heat capacity. The specific heat capacity and mechanical strength values increased from 1330 to 1490 J/kgC and from 4 to 6 MPa, respectively. These results suggest that STESM samples developed from demolition waste can be used reliably in solar heat industrial applications for long term.
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Assessment of Solid Wastes and By-Products as Solid Particle Materials for Concentrated Solar Power Plants

  • Majó Robles, Marc
  • Calderón Díaz, Alejandro
  • Salgado Pizarro, Rebeca
  • Svobodova Sedlackova, Adela
  • Barreneche, Camila
  • Chimenos Ribera, Josep Ma.
  • Fernández Renna, Ana Inés
The revalorization of solid wastes and by-products to be applied as solid particles in concentrated solar power (CSP) leads to cost savings and progresses toward more sustainable technology. Herein, the physicochemical, morphological, thermal, and solar absorption properties are evaluated for electric arc furnace dust, black slag from the steel industry, and Gossan waste from the Rio Tinto mining industry. The principal objectives of this work are (i) to carry out a thermal aging at 900 °C at different times, (ii) to assess the solid's stability throughout the evaluation of physicochemical, morphological, thermal, and optical properties of the material as received, after 300 and 500 h of thermal aging, and (iii) to determine the most appropriate candidate as a thermal energy storage medium and heat transfer fluid for the CSP concept with solid particles. The results show that electric arc furnace black slag is the most suitable candidate from the three solids studied, as it is the one that optimizes the combination of absorptance, thermal conductivity, and chemical stability after thermal aging.
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Advancing sensible heat storage: A novel transient heat transfer model for concrete-based TES modules for CSP applications

  • Tagle-Salazar, Pablo D.
  • Cabeza, Luisa F.
  • Prieto, Cristina
Concentrating solar power (CSP) plays a crucial role in renewable energy systems, offering high-temperature heat for electricity generation and industrial processes while supporting the transition to sustainable energy. Thermal energy storage (TES) improves the reliability and dispatchability of CSP systems. Among the sensible heat storage options, concrete emerges as a cost-effective and eco-friendly alternative that warrants further investigation. This study introduces a comprehensive mathematical model for simulating the transient thermal behaviour of concrete-based TES modules. The model accommodates diverse geometries, supports a wide range of heat transfer fluids (HTFs) in all flow regimes, and accounts for heat losses to the environment, factors that are often overlooked in prior research. The mathematical framework was incorporated into a software platform called OpenModelica and will later be included in a tool developed by the authors to evaluate the performance of CSP plants. Before this integration takes place, the model undergoes validation, which is the primary focus of this study. The model was validated through two case studies, one theoretical and the other experimental, each involving different operational conditions, geometries, HTFs, and materials. The theoretical case confirmed that the model could capture the key physical phenomena governing transient heat transfer in the storage module. A comparison between the simulation results and experimental data revealed a strong agreement in temperature, heat flow, and total energy transmitted, with temperature errors within the IEC 60751 standard and total energy transfer errors ranging from −6.15 % to +5.69 %. These findings highlight the potential of concrete-based TES to enhance the performance of CSP systems, contributing to reliable and sustainable energy solutions., CSP-ERA.NET is supported by the European Commission within the EU Framework Programme for Research and Innovation Horizon 2020 (Cofund ERA-NET Action, N◦ 838311). This study receives funding from the Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (MCIN/AEI/10.13039/501100011033) through the PCI2020-120695-2 project and the European Union “NextGenerationEU"/PRTR”. This work was partially funded by the Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (AEI) (PID2021-123511OB-C31 - MCIN/AEI/ 10.13039/501100011033/FEDER, UE), and by Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (AEI) (RED2024-153629- T). This work is partially supported by ICREA under the ICREA Academia programme. The authors would like to thank the Departament de Recerca i Universitats of the Catalan Government for the quality accreditation given to their research group (2021 SGR 01615). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia.
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

A technical and economic comparison between concrete and latent thermal energy storage for concentrated solar power applications

  • Prieto, Cristina
  • Borri, Emiliano
  • Pavón Moreno, M. Carmen
  • Zsembinszki, Gabriel
  • Cabeza, Luisa F.
Thermal energy storage (TES) plays a key role in concentrating solar power (CSP) plants by enhancing dispatchability and improving overall system efficiency. This study presents a comparative techno-economic analysis of three TES configurations integrated into CSP plants: (i) the conventional two-tank molten salt system, (ii) a phase change material (PCM)-based system with a cascade arrangement, and (iii) a concrete-based system. While technical performance simulations indicate similar annual energy production across all cases, significant differences emerge in economic viability. The PCM TES system demonstrates the lowest levelized cost of electricity (LCoE) at $14.35/kWh, leveraging its high energy density and reduced material requirements, despite lower efficiency (93 % compared to 99 % in molten salt). Conversely, the concrete TES system, while capable of extended discharge at partial loads, incurs higher parasitic losses and investment costs, resulting in a higher LCoE ($16.16/kWh). The cost analysis further highlights the cost-performance quotient (CPQ) as a valuable metric for assessing TES competitiveness, with PCM exhibiting the most favorable CPQ of $1.04/kWh. These findings underscore the necessity of integrating economic assessments into TES selection for CSP plants. Moreover, the study identifies opportunities for cost reduction in concrete TES through optimized modular designs and improved material formulations. This work provides valuable insights for policymakers, engineers, and industry stakeholders aiming to enhance the financial feasibility of next-generation CSP storage solutions., This study receives funding from the Ministerio de Ciencia e Innovación – Agencia Estatal de Investigación (MCIN/AEI/10.13039/501100011033) through the PCI2020-120695-2 project and the European Union “NextGenerationEU”/PRTR“. CSP-ERA.NET is supported by the European Commission within the EU Framework Programme for Research and Innovation Horizon 2020 (Cofund ERA-NET Action, N° 838311). This work was partially funded by the Ministerio de Ciencia e Innovación de España TED2021-132216A-I00 funded by MCIN/AEI/10.13039/501100011033 and the European Union by NextGenerationEU/PRTR. This work was partially funded by the Ministerio de Ciencia e Innovación – Agencia Estatal de Investigación (AEI) (PID2021-123511OB-C31 – MCIN/AEI/10.13039/501100011033/FEDER, UE) and (RED2022-134219-T). This work is partially supported by ICREA under the ICREA Academia programme. The authors from University of Lleida would like to thank the Departament de Recerca i Universitats of the Catalan Government for the quality accreditation given to their research group (2021 SGR 01615). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia.