Skip to main content

ESTUDIO EXPERIMENTAL Y NUMERICO DE REGIONES D PLANAS Y ESPACIALES EN ESTRUCTURAS DE HORMIGON. APLICACION A APOYOS A MEDIA MADERA Y CALICES

BES-2010-030353

•
Funding agency name Ministerio de Ciencia e Innovación
Funding agency acronym MICINN
Program Programa Nacional de Formación de Recursos Humanos de Investigación
Subprogram Subprograma de Proyectos de Investigación Fundamental no Orientada
Call Contratos Predoctorales
Call year 2010
State Plan 2008-2011 Plan Nacional de Investigación Científica, Desarrollo e Innovación Tecnológica
Management unit Subdirección General de Formación e Incorporación de Investigadores
Beneficiary centre UNIVERSITAT POLITÈCNICA DE VALÈNCIA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 2
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Proposal and experimental validation of simplified strut-and-tie models on dapped-end beams

  • Mata Falcon, Jaime|||0000-0001-8701-4410
  • Pallarés Rubio, Luis|||0000-0003-2126-2387
  • Miguel Sosa, Pedro|||0000-0001-5395-8149
[EN] Dapped-end beams are frequent precast concrete elements. Spalling on the top of the hanger reinforcement has been observed to be often their governing failure mode. This failure hinders the geometric definition of strut-and-tie models for design or assessment purposes. In this work, a simplified procedure for defining the geometry of strut-and-tie models considering spalling failures is proposed. The model is based on the results of a specific experimental programme consisting on twenty-eight tests on fifteen different reinforcement configurations with and without inclined reinforcement. The experimental results show that elements with high amounts of reinforcement and hanger reinforcement concentrated in one layer are more prone to spalling failures, and suggest that the geometry of strut-and-tie models is strongly influenced by the behaviour of the nodal region on top of the hanger reinforcement. The model is verified for tests with and without spalling failures, including elements from the literature, showing sound agreement between the modelling results and experimental observations., The authors wish to thank the Spanish Ministry of Science and Innovation for funding Project BIA2009-11369 and for FPI fellowship BES-2010-030353 received by the first author. This work forms part of the first author's doctoral research awarded by the Business Chair of Sustainable and Advanced Construction at the Universitat Polithcnica de Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Experimental and analytical investigation of the crack behaviour of dapped-end beams

  • Mata Falcon, Jaime|||0000-0001-8701-4410
  • Pallarés Rubio, Luis|||0000-0003-2126-2387
  • Yu, Karin L.
  • Miguel Sosa, Pedro
[EN] Reinforced concrete dapped ends are a widely used connection for precast elements in infrastructure and building structures. However, they are prone to major durability problems due to the formation of an inclined crack at the re-entrant corner of the joint. The crack typically forms at low loads and reaches a significant opening under service load conditions, causing corrosion and stress concentration in the reinforcement, which impairs the safety of the connection. The behaviour of these cracks in a highly disturbed structural region is not well understood. This paper presents the experimental results of 28 dapped-end tests in which the crack behaviour in the re-entrant corner was continuously measured using digital image correlation. The main test variables are the amount of dapped-end reinforcement, the presence of diagonal reinforcement and the ratio of horizontal to vertical dapped-end reinforcement area. The bond behaviour of the dapped-end reinforcement was estimated from the measured crack widths and reinforcement strains, assuming a pull-out mechanism with constant bond shear stresses on both crack sides. The paper proposes a model for evaluating the width of corner cracks at service loads, in which the reinforcement strains are derived from strut-and-tie models. The modelling results agreed satisfactorily well with the experimental observations of this study and 28 additional tests from the literature for dapped-ends with reinforcement diameter below 20 mm., The authors wish to thank the Spanish Ministry of Science and Innovation for funding Project BIA2009-11369 and for FPI fellowship BES-2010-030353 received by Jaime Mata-Falco <acute accent> n. A special thanks for supporting the research goes to Prof. Dr. Walter Kaufmann (ETH Zurich) .