Skip to main content

ESTUDIO TEORICO-EXPERIMENTAL DE LA DUCTILIDAD Y DE LA CAPACIDAD DE DEFORMACION DE SOPORTES DE HAR SOMETIDOS A COMPRESION Y CARGA LATERAL CICLICA

BIA2008-03734

•
Funding agency name Ministerio de Ciencia e Innovación
Funding agency acronym MICINN
Program Programa Nacional de Proyectos de Investigación Fundamental
Subprogram Subprograma de Proyectos de Investigación Fundamental no Orientada
Call Proyectos I+D
Call year 2008
State Plan 2008-2011 Plan Nacional de Investigación Científica, Desarrollo e Innovación Tecnológica
Management unit Subdirección General de Proyectos de Investigación
Beneficiary centre UNIVERSITAT POLITÈCNICA DE VALÈNCIA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 4
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Behaviour of steel-fibre-reinforced normal-strength concrete slender columnsunder cyclic loading

  • Caballero Morrison, Karen Elena
  • Bonet Senach, José Luís|||0000-0002-6687-5307
  • Navarro-Gregori, Juan|||0000-0002-6319-7029
  • Martí Vargas, José Rocío|||0000-0003-1665-2348
The inclusion of ductility requirements is necessary to guarantee the safety design of any concrete structure subjected to unexpected and/or reversal loads. It is important to outline that plastic hinges may be developed in columns of reinforced concrete buildings, especially in column-foundation joints. The deformation capacity of the column depends on its slenderness. However, few experimental tests of normal and fibre-reinforced concrete columns in the range of medium slenderness (between 5 and 10) have been performed for the case of cyclic loading. This paper presents an experimental research study on the behaviour of slender columns subjected to combinations of constant axial and lateral cyclic loads. In order to study the behaviour of this type of element fourteen experimental tests were performed. The experimental results make it possible to calibrate numerical models, and to validate simplified methods. The following variables are studied: slenderness, axial load level, transverse reinforcement ratio, and volumetric steel-fibre ratio. The maximum load and deformation capacity of the columns are analyzed. It is interesting to note that the deformation capacity depends on the four test variables analyzed. Moreover, the inclusion of steel fibres into the concrete mixture increases the deformation capacity. The inclusion of a minimum transverse reinforcement is required in order to improve the effectiveness of the steel fibres. Thus, the column behaviour suffers moderate strength losses due to cyclic loads. Finally, slenderness influences the deformation capacity if second-order effects are important, the cross-section displays ductile behaviour, and the capacity of the materials is reached., The authors of this work wish to thank the research bureau of the Spanish Ministry of Science and Innovation and the Plan E, for the funding of the Project BIA 2008-03734 and BIA 2009-10207.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Slenderness limit of the weak axis in the design of rectangular reinforced concrete non-sway columns

  • Cortés-Moreno, Eduardo
  • Bonet Senach, José Luís|||0000-0002-6687-5307
  • Romero, Manuel L.|||0000-0001-5247-4767
  • Miguel Sosa, Pedro|||0000-0001-5395-8149
Most design codes (Model Code 90, ACI-318-2008 and Eurocode-2-2004) suggest that the effect of a geometrical imperfection ought to be taken into account in the most unfavorable direction when designing slender reinforced concrete columns. If the bending plane of the beam-column is related to the strong axis, this imperfection acting in the opposite direction results in the column being subjected to axial load and biaxial bending, complicating the design procedure and increasing computational costs considerably. Such standards do not indicate when this geometrical imperfection generates a notable loss of resistance in the column. This paper proposes the geometrical slenderness of the weak axis (lb/b) as the variable that determines whether or not to consider the influence of such imperfection. This paper denominates this boundary value the "slenderness limit of the weak axis" (¿g,weak), and this is associated with a loss of resistance of 10% of the bending moment of the unbraced columns with respect to non-sway columns. An approximated equation of this limit is proposed using the results of a numerical simulation. The equation is valid for rectangular columns with doubly symmetric reinforcement and both normal and high strength concrete, and also for short-term and sustained loads. © 2011 Elsevier Ltd., The authors wish to express their sincere gratitude to the Spanish "Ministerio de Ciencia e Innovacion" for help provided through projects BIA2008-03734 and BIA2009-10207 and to the European Community for financial support from Feder funds.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

An experimental study of steel fiber-reinforced high-strength concrete slender columns under cyclic loading

  • Caballero Morrison, Karen Elena
  • Bonet Senach, José Luís|||0000-0002-6687-5307
  • Navarro-Gregori, Juan|||0000-0002-6319-7029
  • Serna Ros, Pedro|||0000-0001-8754-1165
Structural engineers usually limit the use of HSC columns to seismic active zones because of their brittle behavior in comparison with NSC, even though it presents advantages both in terms of mechanics and durability. A possible solution to improve the ductile behavior of HSC columns is the use of transverse reinforcement and steel fibers simultaneously. In addition, the use of HSC makes the design of more slender columns possible, with the consequent increase of second-order effects. However, there are few experimental tests on columns of medium slenderness (between 5 and 10) subjected to cyclic loads including or excluding steel fibers. This article presents experimental research work on the behavior of slender columns subjected to combined constant compression and cyclic lateral loads. Fifteen tests were carried out in order to study the behavior of such elements. The following variables were studied: concrete strength, slenderness, axial load level, transverse reinforcement ratio, and volumetric steel-fiber ratio. The maximum load and deformation capacity of the columns were analyzed. The fact that the inclusion of steel fibers into the concrete mixture increases the deformation capacity was verified. Moreover, a minimum transverse reinforcement is required in order to improve the effectiveness of the steel fibers with no significant decrease in the carrying capacity under cyclic loading. The inclusion of steel fibers in HSC can ensure similar ductility values to those of NSC. It was shown that slenderness influences the deformation capacity., The authors of this work wish to thank the research bureau of the Spanish Ministry of Economy and Competitiveness and the Plan E, for the funding of the Project BIA 2008-03734 and BIA 2009-10207.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Effective flexural stiffness of slender reinforced concrete columns under axial forces and biaxial bending

  • Bonet Senach, José Luís|||0000-0002-6687-5307
  • Romero, Manuel L.|||0000-0001-5247-4767
  • Miguel Sosa, Pedro|||0000-0001-5395-8149
Most of the design codes (ACI-318-2008 and Euro Code-2-2004) propose the moment magnifier method in order to take into account the second order effect to design slender reinforced concrete columns. The accuracy of this method depends on the effective flexural stiffness of the column. This paper proposes a new equation to obtain the effective stiffness EI of slender reinforced concrete columns. The expression is valid for any shape of cross-section, subjected to combined axial loads and biaxial bending, both for short-time and sustained loads, normal and high strength concretes, but it is only suitable for columns with equal effective buckling lengths in the two principal bending planes. The new equation extends the proposed EI equation in the "Biaxial bending moment magnifier method" by Bonet et al. (2004) [6], which is valid only for rectangular sections. The method was compared with 613 experimental tests from the literature and a good degree of accuracy was obtained. It was also compared with the design codes ACI-318 (08) and EC-2 (2004) improving the precision. The method is capable to verify and design with sufficient accuracy slender reinforced concrete columns in practical engineering design applications. © 2010 Elsevier Ltd., The authors wish to express their sincere gratitude to the Spanish "Ministerio de Ciencia e Innovacion" for help provided through projects BIA2008-03734 and BIA2009-10207 and to the European Community with the Feder funds.