Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 20
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Effect of Magnesium Addition and High Energy Processing on the Degradation Behavior of Iron Powder in Modified Hanks’ Solution for Bioabsorbable Implant Applications

  • Estrada, Rafael Guillermo
  • Multigner, M.
  • Lieblich, Marcela
  • Fajardo, Santiago
  • Rams Ramos, Joaquín
This paper shows the results of applying a combination of high energy processing and magnesium (Mg) as an alloying element in a strategy for enhancing the degradation rate of iron (Fe) for applications in the field of non-permanent medical implants. For this purpose, Fe powder was milled with 5 wt% of Mg (Fe5Mg) and its microstructure and characterized degradation behavior. As-received Fe powder was also milled in order to distinguish between the effects due to high energy processing from those due to the presence of Mg. The powders were prepared by high energy planetary ball milling for 16 h. The results show that the initial crystallite size diminishes from >150 nm to 16 nm for Fe and 46 nm for Fe5Mg. Static degradation tests of loose powder particles were performed in Hanks’ solution. Visual inspection of the immersed powders and the X-ray diffraction (XRD) phase quantification indicate that Fe5Mg exhibited the highest degradation rate followed by milled Fe and as received Fe, in this order. The analysis of degradation products of Fe5Mg showed that they consist on magnesium ferrite and pyroaurite, which are known to present good biocompatibility and low toxicity. Differences in structural features and degradation behaviors of milled Fe and milled Fe5Mg suggest the effective dissolution of Mg in the Fe lattice. Based on the obtained results, it can be said that Fe5Mg powder would be a suitable candidate for non-permanent medical implants with a higher degradation rate than Fe., Financial support of the Ministry of Science and Innovation of Spain (MICINN) PID2019-104351GB-C21, PCIN-2017-036 (M-era.Net2016:4128, EU-FEDER), and RTI2018-096391-B-C31, and Comunidad de Madrid ADITIMAT-CM (S2018/NMT-4411) are greatly acknowledged. R. Estrada thanks MICINN for FPI grant PRE2020-092118, and S. Fajardo expresses his gratitude to the State Research Agency (MICINN), the Spanish National Research Council (CSIC), and the European Regional Development Fund (ERDF) for their support under project RYC2019-027006-I (AEI/FEDER/UE).
Archivo Digital UPM
Publication Artículo científico (JournalArticle)

Monitoring Crack Propagation in Skin-Stringer Elements Using Carbon Nanotube Doped Adhesive Films: Influence of Defects and Manufacturing Process

  • Fernández Sánchez-Romate, Xoan Xosé|||0000-0001-9283-4712
  • Moriche Tirado, Rocío
  • Renato Pozo, Angel
  • Jiménez Suárez, Alberto
  • Sánchez, María
  • Güemes Gordo, Jesús Alfredo|||0000-0002-6700-3455
  • Ureña, Alejandro
Archivo Digital UPM
Publication Artículo científico (JournalArticle)

Thermomechanical Characterisation of W-Eurofer 97 Brazed Joints

  • Tejado Garrido, Elena María|||0000-0002-5240-6702
  • Prado Escudero, Javier de
  • Tarancón Román, Sandra|||0000-0002-2910-8707
  • Sánchez Martínez, María
  • Martín Sanz, Antonia|||0000-0003-1291-948X
  • Pastor Caño, Jose Ygnacio|||0000-0003-3561-5999
  • Ureña Fernández, Alejandro
Archivo Digital UPM
Publication Artículo científico (JournalArticle)

W-Cu Metal Matrix Composites for Next Generation Fusion Devices

Archivo Digital UPM
Publication Artículo científico (JournalArticle)

Beneficial Effects of a WC Addition in FAST-Densified Tungsten

  • Novak, Sasa
  • Kocen, Matej
  • Sestan Zavasnik, Andreja
  • Galatanu, Andrei
  • Galatanu, Magdalena
  • Tarancón Román, Sandra|||0000-0002-2910-8707
  • Tejado Garrido, Elena María|||0000-0002-5240-6702
  • Pastor Caño, Jose Ygnacio|||0000-0003-3561-5999
  • Jenus, Petra
Archivo Digital UPM
Publication Artículo científico (JournalArticle)

Processing of WC/W Composites for Extreme Environments by Colloidal Dispersion of Powders and SPS Sintering

  • García Ayala, Esperanza Macarena
  • Tarancón Román, Sandra|||0000-0002-2910-8707
  • González Granados, Zoilo
  • Ferrari Fernández, Begoña
  • Pastor Caño, Jose Ygnacio|||0000-0003-3561-5999
  • Sánchez Herencia, Antonio Javier
Archivo Digital UPM
Publication Artículo científico (JournalArticle)

Overlapping Limitations for ps-Pulsed LIFT Printing of High Viscosity Metallic Pastes

  • Muñoz Martín, David|||0000-0001-5837-6367
  • Chen, Yu
  • Morales Furió, Miguel|||0000-0001-7425-9742
  • Molpeceres Álvarez, Carlos Luis|||0000-0002-6236-8359
Archivo Digital UPM
Publication Artículo científico (JournalArticle)

Influence of the Gap between Substrates in the Laser-Induced Transference of High-Viscosity Pastes

  • Moreno Labella, Juan José|||0000-0003-2612-707X
  • Muñoz Martín, David|||0000-0001-5837-6367
  • Vallejo, Guillermo
  • Molpeceres Álvarez, Carlos Luis|||0000-0002-6236-8359
  • Morales Furió, Miguel|||0000-0001-7425-9742
Archivo Digital UPM
Publication Artículo científico (JournalArticle)

Numerical study of water-glycerol BA-LIFT: Analysis and simulation of secondary effects

  • Moreno Labella, Juan José|||0000-0003-2612-707X
  • Muñoz Martín, David|||0000-0001-5837-6367
  • Márquez Fernández, Andrés
  • Morales Furió, Miguel|||0000-0001-7425-9742
  • Molpeceres Álvarez, Carlos Luis|||0000-0002-6236-8359
Archivo Digital UPM
Publication Artículo científico (JournalArticle)

Cavitation bubble evidence in BA-LIFT processes

  • Moreno Labella, Juan José|||0000-0003-2612-707X
  • Muñoz Martín, David|||0000-0001-5837-6367
  • Morales Furió, Miguel|||0000-0001-7425-9742
  • Molpeceres Álvarez, Carlos Luis|||0000-0002-6236-8359
Archivo Digital UPM
Publication Artículo científico (JournalArticle)

Picosecond Laser Shock Micro-Forming of Stainless Steel: Influence of High-Repetition Pulses on Thermal Effects

  • López López, José Manuel|||0000-0002-0298-3683
  • Muñoz Martín, David|||0000-0001-5837-6367
  • Moreno Labella, Juan José|||0000-0003-2612-707X
  • Panizo Laíz, Miguel|||0000-0001-9061-7888
  • Gómez Rosas, Gilberto
  • Molpeceres Álvarez, Carlos Luis|||0000-0002-6236-8359
  • Morales Furió, Miguel|||0000-0001-7425-9742
Archivo Digital UPM
Publication Artículo científico (JournalArticle)

Subwavelength LIPSS formation on SS304 by picosecond laser irradiation under water confinement

  • Patricia Rivera, Laura|||0000-0001-6373-654X
  • Muñoz Martín, David|||0000-0001-5837-6367
  • Chávez Chávez, Árturo|||0000-0003-3772-905X
  • Morales Furió, Miguel|||0000-0001-7425-9742
  • Gómez Rosas, Gilberto|||0000-0003-2040-3520
  • Molpeceres Álvarez, Carlos Luis|||0000-0002-6236-8359
Archivo Digital UPM
Publication Artículo científico (JournalArticle)

Bio-inspired redesign of a hip prosthesis stem for improving geometrical optimization time

  • Orellana Barrasa, Jaime|||0000-0003-1822-7839
  • Palacios García, Teresa|||0000-0001-7777-6518
  • Calle Gómez, Fernando|||0000-0001-7869-6704
  • Pastor Caño, Jose Ygnacio|||0000-0003-3561-5999
Archivo Digital UPM
Publication Artículo científico (JournalArticle)

Influence of HRGO Nanoplatelets on Behaviour and Processing of PMMA Bone Cement for Surgery

  • Orellana Barrasa, Jaime|||0000-0003-1822-7839
  • Pastor, Ynés Yohana
  • Calle Gómez, Fernando|||0000-0001-7869-6704
  • Pastor Caño, Jose Ygnacio|||0000-0003-3561-5999
Archivo Digital UPM
Publication Artículo científico (JournalArticle)

Characterisation and Modelling of PLA Filaments and Evolution with Time

  • Orellana Barrasa, Jaime|||0000-0003-1822-7839
  • Ferrández Montero, Ana|||0000-0003-3399-1069
  • Ferrari Fernández, Begoña|||0000-0003-3377-6844
  • Pastor Caño, Jose Ygnacio|||0000-0003-3561-5999
Archivo Digital UPM
Publication Artículo científico (JournalArticle)

Natural ageing of PLA filaments, Can it be frozen?

  • Orellana Barrasa, Jaime|||0000-0003-1822-7839
  • Ferrández Montero, Ana|||0000-0003-3399-1069
  • Ferrari Fernández, Begoña|||0000-0003-3377-6844
  • Pastor Caño, Jose Ygnacio|||0000-0003-3561-5999
Archivo Digital UPM
Publication Artículo científico (JournalArticle)

The mechanical, thermal, and chemical properties of PLA-Mg filaments produced via a colloidal route for fused-filament fabrication

  • Orellana Barrasa, Jaime|||0000-0003-1822-7839
  • Ferrández Montero, Ana|||0000-0003-3399-1069
  • Boccaccini, Aldo|||0000-0002-7377-2955
  • Ferrari Fernández, Begoña|||0000-0003-3377-6844
  • Pastor Caño, Jose Ygnacio|||0000-0003-3561-5999
Archivo Digital UPM
Publication Artículo científico (JournalArticle)

Effects of accelerating the ageing of 1D PLA filaments after fused filament fabrication

  • Orellana Barrasa, Jaime|||0000-0003-1822-7839
  • Tarancón Román, Sandra|||0000-0002-2910-8707
  • Pastor Caño, Jose Ygnacio|||0000-0003-3561-5999
Archivo Digital UPM
Publication Artículo científico (JournalArticle)

Effects of Laser Shock Processing on the Mechanical Properties of 6061-T6 Aluminium Alloy Using Nanosecond and Picosecond Laser Pulses

  • Arredondo Bravo, Martha Guadalupe|||0009-0005-6993-0171
  • Gómez Rosas, Gilberto|||0000-0003-2040-3520
  • Morales Furió, Miguel|||0000-0001-7425-9742
  • Muñoz Martín, David|||0000-0001-5837-6367
  • Moreno Labella, Juan José|||0000-0003-2612-707X
  • López López, José Manuel|||0000-0002-0298-3683
  • Quiñones Galvan, Jose Guadalupe|||0000-0001-7931-3955
  • Rubio González, Carlos|||0000-0002-4447-3788
  • Casillas Rodríguez, Francisco Javier|||0000-0001-5928-8182
  • Molpeceres Álvarez, Carlos Luis|||0000-0002-6236-8359
Archivo Digital UPM
Publication Artículo científico (JournalArticle)

Blister-actuated laser-induced forward transfer (BA-LIFT): Understanding blister dynamics for enhanced process control

  • Moreno Labella, Juan José|||0000-0003-2612-707X
  • Candorcio Simón, Rocio|||0000-0001-6302-1595
  • Muñoz Martín, David|||0000-0001-5837-6367
  • Lauzurica Santiago, Sara|||0000-0003-4398-6474
  • Morales Furió, Miguel|||0000-0001-7425-9742
  • Molpeceres Álvarez, Carlos Luis|||0000-0002-6236-8359