Skip to main content

TECNOLOGIAS DE SEGURIDAD CIVIL BASADAS EN FIBRA OPTICA

TEC2012-37958-C02-01

•
Funding agency name Ministerio de Economía y Competitividad
Funding agency acronym MINECO
Program Programa Nacional de Proyectos de Investigación Fundamental
Subprogram Subprograma de Proyectos de Investigación Fundamental no Orientada
Call Proyectos I+D
Call year 2012
State Plan 2008-2011 Plan Nacional de Investigación Científica, Desarrollo e Innovación Tecnológica
Management unit Secretaría de Estado de Investigación, Desarrollo e Innovación
Beneficiary centre UNIVERSIDAD DE ALCALA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 31
Encontrada(s) 1 página(s)

e_Buah Biblioteca Digital Universidad de Alcalá
Publication Artículo científico (JournalArticle)

Relative intensity noise transfer reduction in raman-assisted BOTDA systems

  • Angulo Vinuesa, Xabier
  • Bacquet, D.
  • Martín López, Sonia|||0000-0001-5203-6206
  • Corredera Guillén, Pedro
  • Szriftgiser, P.
  • González Herráez, Miguel|||0000-0003-2555-2971
Raman-assistance (RA) has been identified as a promising technique to extend the measurement range of Brillouin optical time-domain analysis (BOTDA)-based distributed sensors. Unfortunately, Raman amplification introduces a great amount of relative intensity noise (RIN) to the detected low-frequency probe wave. This RIN transfer problem has been widely identified as a major limitation in RA-BOTDA. In vector BOTDA (VBOTDA), the detected signal is transferred to a high-frequency carrier where the Raman RIN transfer turns out to be much less harmful. In addition, a VBOTDA can also provide information about the phase-shift induced by the local stimulated Brillouin scattering gain curve, paving the way for dynamic measurements. In this letter, we demonstrate, for the first time to our knowledge, the RA in a VBOTDA obtaining gain and phase measurements. Our results show a significant reduction of the RIN transfer effect in RA-VBOTDA compared with standard RA-BOTDA, making this type of scheme particularly interesting for long-range and dynamic distributed sensing., European Commission, Ministerio de Economía y Competitividad, Comunidad de Madrid
e_Buah Biblioteca Digital Universidad de Alcalá
Publication Artículo científico (JournalArticle)

Compound Lasing Fiber Optic Ring Resonators for Sensor Sensitivity Enhancement

  • Rota Rodrigo, Sergio
  • González Herráez, Miguel|||0000-0003-2555-2971
  • López Amo, M.
In this study, a new method for increasing simultaneously the sensitivity and interrogation stability of fiber-optic intensity sensors is presented. The configuration is based on a double-coupler ring resonator. On one side, the attenuation sensitivity of the sensor is enhanced by placing it inside a ring resonator. On the other side, the stability of the interrogation method is widely improved by creating an external lasing ring resonator with matched spectral response. The combination of the wavelength selective response of the ring resonator and optical amplification from Er-doped fiber amplifier is used to create different fiber lasers. The resulting lasers present an impressive sensitivity enhancement and a dynamic range increment up to 15 dB. Simultaneously, the instability of the system is reduced to ±0.05 dB. In comparison with systems based on tunable laser interrogation, our method is >100 times more stable and also simpler, as no wavelength tunable elements are required., Ministerio de Economía y Competitividad, European Commission
e_Buah Biblioteca Digital Universidad de Alcalá
Publication Artículo científico (JournalArticle)

Modulation instability-induced fading in phase-sensitive optical time-domain reflectometry

  • Fidalgo Martins, Hugo|||0000-0003-3927-8125
  • Martín López, Sonia|||0000-0001-5203-6206
  • Corredera Guillén, Pedro
  • Salgado, P.
  • Frazão, O.
  • González Herráez, Miguel|||0000-0003-2555-2971
Phase-sensitive optical time-domain reflectometry (φOTDR) is a simple and effective tool allowing the distributed monitoring of vibrations along single-mode fibers. We show in this Letter that modulation instability (MI) can induce a position-dependent signal fading in long-range φOTDR over conventional optical fibers. This fading leads to a complete masking of the interference signal recorded at certain positions and therefore to a sensitivity loss at these positions. We illustrate this effect both theoretically and experimentally. While this effect is detrimental in the context of distributed vibration analysis using φOTDR, we also believe that the technique provides a clear and insightful way to evidence the Fermi-Pasta-Ulam recurrence associated with the MI process., European Commission, Ministerio de Economía y Competitividad, Comunidad de Madrid
e_Buah Biblioteca Digital Universidad de Alcalá
Publication Artículo científico (JournalArticle)

Modulation instability-induced visibility fading in phase-sensitive OTDR

  • Fidalgo Martins, Hugo|||0000-0003-3927-8125
  • Martín López, Sonia|||0000-0001-5203-6206
  • Corredera Guillén, Pedro
  • Salgado, P.
  • Frazão, O.
  • González Herráez, Miguel|||0000-0003-2555-2971
Phase-sensitive optical time domain reflectometry (ΦOTDR) is a simple and effective tool that allows the distributed monitoring of vibrations along single-mode fibers. In this letter we study the effects of modulation instability (MI) in long-range ΦOTDR over conventional optical fibers. We demonstrate both theoretically and experimentally that MI can induce a position-dependent signal fading which leads to a nearly complete visibility loss in the interference signal recorded at certain positions and therefore to a sensitivity loss at these positions. While this effect is detrimental in the context of distributed vibration analysis using ΦOTDR, we also believe that the technique provides a clear and insightful way to evidence the Fermi-Pasta-Ulam (FPU) recurrence associated to the MI process., Ministerio de Economía y Competitividad, Comunidad de Madrid, European Commission
e_Buah Biblioteca Digital Universidad de Alcalá
Publication Artículo científico (JournalArticle)

High-sensitivity dispersive Mach–Zehnder interferometer based on a dissimilar-doping dual-core fiber for sensing applications

  • Fidalgo Martins, Hugo|||0000-0003-3927-8125
  • Bierlich, J.
  • Wondraczek, K.
  • Unger, S.
  • Kobelke, J.
  • Schuster, K.
  • Marques, M. B.
  • González Herráez, Miguel|||0000-0003-2555-2971
  • Frazão, O.
A dual-core fiber in which one of the cores is doped with germanium and the other with phosphorus is used as an in-line Mach–Zehnder dispersive interferometer. By ensuring an equal length but with different dispersion dependencies in the interferometer arms (the two cores), high-sensitivity strain and temperature sensing are achieved. Opposite sensitivities for high and low wavelength peaks were also demonstrated when strain and temperature was applied. To our knowledge this is the first time that such behavior is demonstrated using this type of in-line interferometer based on a dual-core fiber. A sensitivity of 0.102 0.002 nm∕με, between 0 and 800 με and −4.2 0.2 nm∕°C between 47°C and 62°C is demonstrated., European Commission, Ministerio de Economía y Competitividad
e_Buah Biblioteca Digital Universidad de Alcalá
Publication Artículo científico (JournalArticle)

Simple Method for the Elimination of Polarization Noise in BOTDA Using Balanced Detection and Orthogonal Probe Sidebands

  • López Gil, Alexia Inés
  • Domínguez López, Alejandro|||0000-0001-6065-6106
  • Martín López, Sonia|||0000-0001-5203-6206
  • González Herráez, Miguel|||0000-0003-2555-2971
Polarization noise arises in Brillouin optical timedomain analysis due to the strong polarization sensitivity of stimulated Brillouin scattering. To avoid this noise, it turns out to be indispensable to perform some kind of polarization scrambling, either in the pump pulse, the probe signal or both. This is usually achieved using polarization scrambling/switching systems, which, being mechanical, tend to be not as robust as it would be desirable. In this paper, we propose a completely passive system,with no moving parts, to eliminate polarization noise in a BOTDA. It is based on the use of passive depolarization of the pump pulse together with balanced detection among orthogonally polarized Stokes and anti-Stokes bands of the probe signal. The setup requires no alignment readjustment over time and provides a performance similar to a conventional BOTDA using scrambler., Ministerio de Economía y Competitividad, Comunidad de Madrid, European Commission
e_Buah Biblioteca Digital Universidad de Alcalá
Publication Artículo científico (JournalArticle)

Raman-assisted Vector Brillouin Optical Time Domain Analysis

  • Angulo Vinuesa, Xabier
  • Bacquet, D.
  • Martín López, Sonia|||0000-0001-5203-6206
  • Corredera Guillén, Pedro
  • Szriftgiser, P.
  • González Herráez, Miguel|||0000-0003-2555-2971
Raman-assistance (RA) has become a promising technique to enhance the sensing range of standard Brillouin Optical Time Domain Analysis (BOTDA) fiber sensors due to its ability to amplify in a distributed way all the interacting signals within the fiber. Unfortunately, Raman amplification introduces a great amount of Relative Intensity Noise (RIN) to the detected low-frequency probe wave. This RIN transfer problem has been widely identified as a major limitation in RABOTDA. In Vector Brillouin Optical Time Domain Analysis (VBOTDA) the detected signal is transferred to a highfrequency carrier where the Raman RIN transfer turns out to be much less harmful. In this work we demonstrate, for the first time to our knowledge, Raman-assistance in a VBOTDA. Our results show significant reduction of the RIN transfer effect in RA-VBOTDA compared to standard RA-BOTDA, making this type of scheme particularly interesting for long range distributed sensing., European Commission, Ministerio de Economía y Competividad, Comunidad de Madrid
e_Buah Biblioteca Digital Universidad de Alcalá
Publication Artículo científico (JournalArticle)

Gain vs phase in BOTDA setups

  • López Gil, Alexia Inés
  • Angulo Vinuesa, Xabier
  • Soto Hernández, Marcelo Alfonso
  • Domínguez López, Alejandro|||0000-0001-6065-6106
  • Martín López, Sonia|||0000-0001-5203-6206
  • Thévenaz, Luc
  • González Herráez, Miguel|||0000-0003-2555-2971
We evaluate the Brillouin frequency shift (BFS) determination error when using the Brillouin phase spectrum (BPS) instead of the Brillouin gain spectrum (BGS) in BOTDA setups. We compare the error obtained in the BFS determination in both cases, both with theoretical arguments and experimental data. In comparison to the gain, for an equal SNR and linewidth, the phase generally provides a better fit of the BFS for smaller frequency spans. This result opens a possible way to reduce the measurement time of certain BOTDA systems by using the phase feature, Ministerio de Economía y Competitividad, Comunidad de Madrid, Universidad de Alcalá, European Commission
e_Buah Biblioteca Digital Universidad de Alcalá
Publication Artículo científico (JournalArticle)

Compound lasing fiber optic ring resonators for sensing

  • Rota Rodrigo, Sergio
  • González Herráez, Miguel|||0000-0003-2555-2971
  • López Amo, M.
In this work, we present a new method for increasing simultaneously the sensitivity and interrogation stability of fiberoptic intensity sensors. The configuration is based on a double-coupler ring resonator. On one side, the attenuation sensitivity of the sensor is enhanced by placing it inside a ring resonator. On the other side, the stability of the interrogation method is rendered close to perfect by creating an external lasing ring resonator with matched spectral response. The resulting lasers allow the stable interrogation of the sensors with an impressive sensitivity enhancement. In our experiments, the dynamic range of the intensity sensor (and consequently its sensitivity) is increased 15 dB by using this laser-based interrogation system. Simultaneously, the instability of the system is reduced to ±0.05 dB. In comparison with systems based on external interrogation, our method is <100 times more stable and also simpler, as no wavelength tunable elements are required., Ministerio de Ciencia e Innovación, Ministerio de Economía y Competitividad, European Commission
e_Buah Biblioteca Digital Universidad de Alcalá
Publication Artículo científico (JournalArticle)

Exploiting nonreciprocity in BOTDA systems

  • López Gil, Alexia Inés
  • Angulo Vinuesa, Xabier
  • Domínguez López, Alejandro|||0000-0001-6065-6106
  • Martín López, Sonia|||0000-0001-5203-6206
  • González Herráez, Miguel|||0000-0003-2555-2971
In this Letter, we present and demonstrate a novel technique for distributed measurements in Brillouin optical time-domain analysis based on the use of the nonlinear phase-shift induced by stimulated Brillouin scattering. Employing a Sagnac interferometer (SI), the position-resolved Brillouin phase-shift spectrum (BPS) along the fiber can be obtained, benefiting from the sensitivity to nonreciprocal phase-shifts of the SI scheme. This proposal simplifies the existing methods to retrieve the BPS distribution along an optical fiber since phase modulation, filtering, and high-bandwidth detectors are not required. The fundamentals of the technique are described theoretically and validated through numerical simulations and experimental measurements., European Commission, Ministerio de Economía y Competitivdad, Comunidad de Madrid, Universidad de Alcalá
e_Buah Biblioteca Digital Universidad de Alcalá
Publication Artículo científico (JournalArticle)

Distributed phase birefringence measurements based on polarization correlation in phase-sensitive optical time-domain reflectometers

  • Soto Hernández, Marcelo Alfonso
  • Fidalgo Martins, Hugo|||0000-0003-3927-8125
  • González Herráez, Miguel|||0000-0003-2555-2971
  • Thévenaz, Luc
In this paper a technique to measure the distributed birefringence profile along optical fibers is proposed and experimentally validated. The method is based on the spectral correlation between two sets of orthogonally-polarized measurements acquired using a phase-sensitive optical time-domain reflectometer (φOTDR). The correlation between the two measured spectra gives a resonance (correlation) peak at a frequency detuning that is proportional to the local refractive index difference between the two orthogonal polarization axes of the fiber. In this way the method enables local phase birefringence measurements at any position along optical fibers, so that any longitudinal fluctuation can be precisely evaluated with metric spatial resolution. The method has been experimentally validated by measuring fibers with low and high birefringence, such as standard single-mode fibers as well as conventional polarizationmaintaining fibers. The technique has potential applications in the characterization of optical fibers for telecommunications as well as in distributed optical fiber sensing., European Commission, Ministerio de Economía y Competitividad, Comunidad de Madrid
e_Buah Biblioteca Digital Universidad de Alcalá
Publication Artículo científico (JournalArticle)

Waveguide saturable absorbers at 1.55 μm based on intraband transitions in GaN/AlN QDs

  • Monteagudo Lerma, Laura
  • Valdueza Felip, Sirona|||0000-0003-1817-5354
  • Naranjo Vega, Fernando Bernabé|||0000-0002-2119-6749
  • Corredera Guillén, Pedro
  • Rapenne, L.
  • Sarigiannidou, E.
  • Strasser, G.
  • Monroy, Eva
  • González Herráez, Miguel|||0000-0003-2555-2971
We report on the design, fabrication and optical characterization of GaN/AlN quantum-dot-based waveguides for all-optical switching via intraband absorption saturation at 1.55 µm. The transmittance of the TM-polarized light increases with the incident optical power due to the saturation of the s-pz intraband absorption in the QDs. Single-mode waveguides with a ridge width of 2 µm and a length of 1.5 mm display 10 dB absorption saturation of the TM-polarized light for an input pulse energy of 8 pJ and 150 fs., Ministerio de Economía y Competitividad, Comunidad de Madrid
e_Buah Biblioteca Digital Universidad de Alcalá
Publication Artículo científico (JournalArticle)

Limits of BOTDA Range Extension Techniques

  • Angulo Vinuesa, Xabier
  • Domínguez López, Alejandro|||0000-0001-6065-6106
  • López Gil, Alexia Inés
  • Ania Castañón, Juan Diego
  • Martín López, Sonia|||0000-0001-5203-6206
  • González Herráez, Miguel|||0000-0003-2555-2971
Brillouin-based temperature and strain sensors have attracted great attention of both the academic and industrial sectors in the past few decades due to their ability to perform distributed measurements. Particularly, Brillouin Optical Time Domain Analysis (BOTDA) systems have been applied in many different scenarios, proving particularly useful in those requiring especially wide coverage ranging extremely long distances, such as in civil structure monitoring, energy transportation or environmental applications. The extension of the measuring range in these sensors has therefore become one of the main areas of research and development around BOTDA. To do so, it is necessary to increase the Signal to Noise Ratio (SNR) of the retrieved signal. So far, several techniques have been applied in order to achieve this goal, such as pre-amplification before detection, pulse coding or Raman amplification. Here, we analyze these techniques in terms of their performance limits and provide guidelines that can assist in finding out which is the best configuration to break current range limitations. Our analysis is based on physical arguments as well as current literature results., European Commission, Ministerio de Economía y Competitividad, Universidad de Alcalá, Ministerio de Ciencia e Innovación, Comunidad de Madrid
e_Buah Biblioteca Digital Universidad de Alcalá
Publication Artículo científico (JournalArticle)

Strong Cancellation of RIN Transfer in a Raman-Assisted BOTDA Using Balanced Detection

  • Domínguez López, Alejandro|||0000-0001-6065-6106
  • López Gil, Alexia Inés
  • Martín López, Sonia|||0000-0001-5203-6206
  • González Herráez, Miguel|||0000-0003-2555-2971
Raman assistance is one of the most interesting routes toward extending the range of Brillouin optical timedomain analysis (BOTDA) systems. Unfortunately, the use of Raman amplification normally entails an important relative intensity noise (RIN) transfer toward the probe wave, which severely limits this approach. In this letter, we show that the RIN transfer problem can be effectively avoided using a slightly modified scheme comprising a dual-sideband modulated probe and balanced detection. Our measurements clearly indicate a nearly complete cancellation of the RIN noise in the detected trace signal. The use of balanced detection in our Raman-assisted BOTDA setup implies a fivefold increase in figure of merit compared with the same setup using conventional detection., European Commission, Ministerio de Economía y Competitividad
e_Buah Biblioteca Digital Universidad de Alcalá
Publication Artículo científico (JournalArticle)

Distributed vibration sensing over 125 km with enhanced SNR using ΦOTDR over a URFL cavity

  • Fidalgo Martins, Hugo|||0000-0003-3927-8125
  • Martín López, Sonia|||0000-0001-5203-6206
  • Corredera Guillén, Pedro
  • Ania Castañón, Juan Diego
  • Frazão, O.
  • González Herráez, Miguel|||0000-0003-2555-2971
We describe the use of a phase-sensitive optical time domain reflectometer (ΦOTDR) over an ultra-long Raman fiber laser cavity allowing fully distributed detection of vibrations over 125 km. Compared to a first-order Raman-assisted ΦOTDR, this scheme shows an enhanced signal-to-noise ratio (SNR). This is due to the fact that the relative intensity noise introduced by the Raman amplification is mostly transferred to a lower frequency range, where the balanced detection implemented in the setup provides better suppression of the common-mode noise. The sensor was able to measure vibrations of up to 380 Hz (limit set by the time of flight of light pulses) in a distance of 125 km with a resolution of 10 m and an average SNR of 8 dB with no postprocessing. This implies a >3 dB improvement in SNR over a first-order Raman-assisted setup with similar characteristics, Ministerio de Economía y Competitividad, Ministerio de Ciencia e Innovación, Comunidad de Madrid, European Commission
e_Buah Biblioteca Digital Universidad de Alcalá
Publication Artículo científico (JournalArticle)

PROUD-based method for simple real-time in-line characterization of propagation-induced distortions in NRZ data signals

  • Fidalgo Martins, Hugo|||0000-0003-3927-8125
  • Pastor Graells, Juan
  • Cortés, L.R.
  • Piote, D.
  • Martín López, Sonia|||0000-0001-5203-6206
  • Azaña, José
  • González Herráez, Miguel|||0000-0003-2555-2971
A simple, in-line method for real-time full characterization (amplitude and phase) of propagation distortions arising due to group velocity dispersion and self-phase modulation on 10-20 Gbps transmitted NRZ optical signals is reported. It is based on phase reconstruction using optical ultrafast differentiation (PROUD), a linear and self-referenced technique. The flexibility of the technique is demonstrated by characterizing different data stream scenarios. Experimental results were modelled using conventional propagation equations, showing good agreement with the measured data. It is envisaged that the proposed method could be used in combination with DSP techniques for the estimation and compensation of propagation distortions in fiber links, not only in conventional IM/DD systems but also in coherent systems with advanced modulation formats., European Commission, Comunidad de Madrid, Ministerio de Economía y Competitividad, Universidad de Alcalá
e_Buah Biblioteca Digital Universidad de Alcalá
Publication Artículo científico (JournalArticle)

Phase-sensitive optical time domain reflectometer assisted by first-order raman amplification for distributed vibration sensing over >100 km

  • Fidalgo Martins, Hugo|||0000-0003-3927-8125
  • Martín López, Sonia|||0000-0001-5203-6206
  • Corredera Guillén, Pedro
  • Filograno, M. L.
  • Frazão, O.
  • González Herráez, Miguel|||0000-0003-2555-2971
In this study, the authors present an experimental and theoretical description of the use of first order Raman amplification to improve the performance of a Phase-sensitive optical time domain reflectometer (φ OTDR) when used for vibration measurements over very long distances. A special emphasis is given to the noise which is carefully characterized and minimized along the setup. A semiconductor optical amplifier and an optical switch are used to greatly decrease the intra-band coherent noise of the setup and balanced detection is used to minimize the effects of RIN transferred from the Raman pumps. The sensor was able to detect vibrations of up to 250 Hz (close to the limits set by the time of flight of light pulses) with a resolution of 10 m in a range of 125 km. To achieve the above performance, no post-processing was required in the φOTDR signal. The evolution of the φOTDR signal along the fiber is also shown to have a good agreement with the theoretical model., European Commission, Ministerio de Economía y Competitividad, Comunidad de Madrid
e_Buah Biblioteca Digital Universidad de Alcalá
Publication Artículo científico (JournalArticle)

Long-range static and dynamic distributed sensing

  • González Herráez, Miguel|||0000-0003-2555-2971
  • Domínguez López, Alejandro|||0000-0001-6065-6106
  • López Gil, Alexia Inés
  • Fidalgo Martins, Hugo|||0000-0003-3927-8125
  • Martín López, Sonia|||0000-0001-5203-6206
  • Angulo Vinuesa, Xabier
  • Corredera Guillén, Pedro
In the past few decades, Brillouin-based distributed temperature and strain sensors have attracted the attention of both the academic and industrial sectors. In particular, B-OTDA systems have been lately a trendy study area due to their numerous and well proofed applications, such as in monitoring large civil structures, energy transportation or environmental applications. One of the main areas of research in B-OTDA sensors focuses on the extension of the measuring range. To do so, it becomes necessary to increase the signal to noise ratio (SNR) of the sensor, in particular considering the reduced signal contrast at the far end of the fiber. Several techniques have been applied in order to achieve this goal, such as Raman amplification and pulse coding. Here, we review some of these techniques (particularly Raman amplification) and their application for range extension of these sensors beyond the 100 km range. In addition, we discuss routes to perform dynamic measurements over such ultra-long spans, European Commission, Ministerio de Economía y Competitividad, Comunidad de Madrid
e_Buah Biblioteca Digital Universidad de Alcalá
Publication Artículo científico (JournalArticle)

Study of high In-content AlInN deposition on p-Si (111) by RF-sputtering

  • Núñez Cascajero, Arántzazu
  • Monteagudo Lerma, Laura
  • Valdueza Felip, Sirona|||0000-0003-1817-5354
  • Navío, C.
  • Monroy, Eva
  • González Herráez, Miguel|||0000-0003-2555-2971
  • Naranjo Vega, Fernando Bernabé|||0000-0002-2119-6749
In this work, we investigate the effects of deposition conditions on the structural and morphological properties of AlInN thin films deposited on p-doped Si(111) substrates by reactive radio-frequency sputtering. The aluminum composition can be tuned in the 0 to 0.36 range by changing the power applied to the aluminum target. Al incorporation leads to a change in the layer morphology and improvement of the rms surface roughness of the layers. The compact Al0.36In0.64N sample grown at 550 °C exhibits intense room-temperature photoluminescence centered at 1.75 eV., Ministerio de Economía y Competitividad, Comunidad de Madrid, Universidad de Alcalá, European Commission
e_Buah Biblioteca Digital Universidad de Alcalá
Publication Artículo científico (JournalArticle)

Infrared SPR sensing with III-nitride dielectric layers

  • Núñez Cascajero, Arántzazu
  • Esteban Martinez, Óscar|||0000-0002-2824-6593
  • Méndez, J.A.
  • González Herráez, Miguel|||0000-0003-2555-2971
  • Naranjo Vega, Fernando Bernabé|||0000-0002-2119-6749
In this work, Aluminum Indium Nitride (AlxIn1-xN) has been used as the dielectric overlay for a surface plasmon resonance sensor. The use of a ternary compound such as AlxIn1-xN for the dielectric allows a fine tuning of its refractive index by varying its composition, thus improving the sensor performance. Narrower transmittance resonances and higher sensitivities are obtained for transducers where the substrate rotates while depositing the ternary compound, which is attributed to the deposition of ternary layers with enhanced homogeneity. The calculated average sensitivity of the devices increases when rising the Al content of the dielectric layer, it being of 4360 nm/RIU, 5230 nm/RIU and 5730 nm/RIU for 0%, 36% and 100%, respectively. The device grown with 36% of Al shows the highest coupling strength. These results show the suitability of AlxIn1-xN compounds as dielectric layers in SPR sensors., Ministerio de Economía y Competitividad, Comunidad de Madrid, Universidad de Alcalá
e_Buah Biblioteca Digital Universidad de Alcalá
Publication Artículo científico (JournalArticle)

Slow-light and enhanced sensitivity in a displacement sensor using a lossy fiber-based ring resonator, Slow-light assisted displacement sensor using a lossy fiber-based ring resonator

  • Bravo, M.
  • Angulo Vinuesa, Xabier
  • Martín López, Sonia|||0000-0001-5203-6206
  • López-Amo, M.
  • González Herráez, Miguel|||0000-0003-2555-2971
Along the last years, much debate has been done on the efficiency of slow-light phenomena in order to enhance light-matter interactions, especially for sensing purposes. This improvement could be key to develop more compact and sensitive devices. In this work we develop an all-fiber sub-micrometric displacement sensor using slow-light sensitivity enhancement in a lossy ring resonator. In the proposed structure the losses produced by the displacement of a mechanic transducer can be translated into strong variations of group index and therefore strong transmittance variations. We show that this effect is strictly related to slow light, and not related to confinement effects or any other., European Commission, Ministerio de Economía y Competitividad, Comunidad de Madrid, Ministerio de Ciencia e Innovación
e_Buah Biblioteca Digital Universidad de Alcalá
Publication Artículo científico (JournalArticle)

Coherent noise reduction in high visibility phase-sensitive optical time domain reflectometer for distributed sensing of ultrasonic waves

  • Fidalgo Martins, Hugo|||0000-0003-3927-8125
  • Martín López, Sonia|||0000-0001-5203-6206
  • Corredera Guillén, Pedro
  • Filograno, M. L.
  • Frazão, O.
  • González Herráez, Miguel|||0000-0003-2555-2971
Phase-sensitive optical time domain reflectometry (\phi \hbox{OTDR}) is a simple and effective tool allowing the distributed monitoring of vibrations along single-mode fibers. Up to now, \phi {\rm OTDRs} have been used mostly for the measurement of sub-kHz vibrations, normally in the context of intrusion sensing. In this paper, the authors present an experimental and theoretical description of a high-visibility \phi {\rm OTDR} and its performance when used for ultrasonic vibration measurements. The use of a semiconductor optical amplifier in the setup allows to suppress coherent noise and also to improve the spectral response of the pump pulses. These two advantages greatly decrease the detected intra-band noise thus allowing frequency measurements in the limits set by the time of flight of the light pulses while maintaining the simplicity of the scheme, as no post-processing, extremely high coherence lasers or coherent detection methods are required. The sensor was able to measure vibrations of up to 39.5 kHz with a resolution of 5 m over a range which could go up to 1.25 km. This is the first time to our knowledge that a fully distributed measurement of ultrasonic waves was achieved. The statistical behavior of the system was also described theoretically and characterized experimentally, European Commission, Ministerio de Economía y Competitividad, Comunidad de Madrid
e_Buah Biblioteca Digital Universidad de Alcalá
Publication Artículo científico (JournalArticle)

Non-local effects in dual-probe-sideband Brillouin optical time domain analysis

  • Domínguez López, Alejandro|||0000-0001-6065-6106
  • Angulo Vinuesa, Xabier
  • López Gil, Alexia Inés
  • Martín López, Sonia|||0000-0001-5203-6206
  • González Herráez, Miguel|||0000-0003-2555-2971
According to recent models, non-local effects in dual-probesideband Brillouin Optical Time Domain Analysis (BOTDA) systems should be essentially negligible whenever the probe power is below the Stimulated Brillouin Scattering (SBS) threshold. This paper shows that actually there appear non-local effects in this type of systems before the SBS threshold. To explain these effects it is necessary to take into account a full spectral description of the SBS process. The pump pulse experiences a frequency-dependent spectral deformation that affects the readout process differently in the gain and loss configurations. This paper provides a simple analytical model of this phenomenon, which is validated against compelling experimental data, showing good agreement. The main conclusion of our study is that the measurements in gain configuration are more robust to this non-local effect than the loss configuration. Experimental and theoretical results show that, for a total probe wave power of ~1 mW (500 μW on each sideband), there is an up-shifting of ~1 MHz in the Brillouin Frequency Shift (BFS) retrieved from the Brillouin Loss Spectrum, whereas the BFS extracted from the measured Brillouin Gain Spectrum is up-shifted only ~0.6 MHz. These results are of particular interest for manufacturers of longrange BOTDA systems., European Commission, Ministerio de Economía y Competitividad, Comunidad de Madrid, Universidad de Alcalá
e_Buah Biblioteca Digital Universidad de Alcalá
Publication Artículo científico (JournalArticle)

Widely power-tunable polarization-independent ultrafast mode-locked fiber laser using bulk InN as saturable absorber

  • Jiménez Rodríguez, Marco
  • Monteagudo Lerma, Laura
  • Monroy, Eva
  • González Herráez, Miguel|||0000-0003-2555-2971
  • Naranjo Vega, Fernando Bernabé|||0000-0002-2119-6749
The growing demand of ultrafast mode-locked fiber lasers in the near infrared has boosted the research activity in this area. One of the most convenient ways to achieve passive mode locking consists of inserting a semiconductor saturable absorber in the laser cavity to modulate the losses. However, in such a configuration, the limited power range of operation is still an unsolved issue. Here we report the fabrication of an ultrafast, high-power, widely power-tunable and non-polarization-dependent mode-locked fiber laser operating at 1.55 μm, using an InN layer as saturable absorber. With post-amplification, this laser delivers 55-fs pulses with a repetition rate of 4.84 MHz and peak power in the range of 1 MW in an all-fiber arrangement., Ministerio de Economía y Competitividad, Comunidad de Madrid
e_Buah Biblioteca Digital Universidad de Alcalá
Publication Artículo científico (JournalArticle)

Toward prevention of pipeline integrity threats using a smart fiber-optic surveillance system

  • Tejedor Noguerales, Javier
  • Fidalgo Martins, Hugo|||0000-0003-3927-8125
  • Piote, D.
  • Macías Guarasa, Javier|||0000-0002-3303-3963
  • Pastor Graells, Juan
  • Martín López, Sonia|||0000-0001-5203-6206
  • Corredera Guillén, Pedro
  • De Smet, F.
  • Postvoll, W.
  • González Herráez, Miguel|||0000-0003-2555-2971
This paper presents the first available report in the literature of a system aimed at the detection and classification of threats in the vicinity of a long gas pipeline. The system is based on phase-sensitive optical time-domain reflectometry technology for signal acquisition and pattern recognition strategies for threat identification. The system operates in two different modes: 1) machine+activity identification, which outputs the activity being carried out by a certain machine; and 2) threat detection, aimed at detecting threats no matter what the real activity being conducted is. Different strategies dealing with position selection and normalization methods are presented and evaluated using a rigorous experimental procedure on realistic field data. Experiments are conducted with eight machine+activity pairs, which are further labeled as threat or nonthreat for the second mode of the system. The results obtained are promising given the complexity of the task and open the path to future improvements toward fully functional pipeline threat detection systems operating in real conditions., European Commission, Comunidad de Madrid, Ministerio de Economía y Competitividad, Universidad de Alcalá
e_Buah Biblioteca Digital Universidad de Alcalá
Publication Artículo científico (JournalArticle)

III-nitride-based waveguides for ultrafast all-optical signal processing at 1.55 μm

  • Monteagudo Lerma, Laura
  • Naranjo Vega, Fernando Bernabé|||0000-0002-2119-6749
  • Valdueza Felip, Sirona|||0000-0003-1817-5354
  • Jiménez Rodríguez, Marco
  • Monroy, Eva
  • Postigo, P.A.
  • Corredera Guillén, Pedro
  • González Herráez, Miguel|||0000-0003-2555-2971
We present an overview of the recently developed III-nitride-based optical waveguides for application in ultrafast signal processing at telecom wavelengths. We focus on different active and passive optical devices for further implementation within all-optical integrated circuits. Optical waveguides based on GaN/AlN quantum dots have been demonstrated to act as saturable absorbers requiring ∼3 pJ of input pulse energy to reach +3 dB transmittance contrast for TM-polarized light. On the contrary, sputtered-InN-based devices show -3 dB transmittance contrast associated to two-photon absorption for input pulse energies of ∼1 pJ, making them suitable to act as highly-efficient reverse saturable absorbers. Finally, the passive optical nature of waveguides based on sputtered AlN at 1.55 μm makes them suitable for further connections between different III-nitride-based active devices. Similar to the development of electronic integrated circuits, photonic integrated circuits are being widely investigated to implement active and passive optical functions in different material platforms. III-nitrides on sapphire substrates emerge as efficient all-optical solutions within the photonic integrated circuit presenting high nonlinear behavior and ultrafast response. These heterostructures make possible the full exploitation of the optical fiber bandwidth which is highly required in today's globalized world. © 2015 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim., Ministerio de Economía y Competitividad, Comunidad de Madrid, Universidad de Alcalá, European Commission
e_Buah Biblioteca Digital Universidad de Alcalá
Publication Artículo científico (JournalArticle)

Morphology and arrangement of InN nanocolumns deposited by radio-frequency sputtering: Effect of the buffer layer

  • Monteagudo Lerma, Laura
  • Valdueza Felip, Sirona|||0000-0003-1817-5354
  • Núñez Cascajero, Arántzazu
  • Ruiz, A.
  • González Herráez, Miguel|||0000-0003-2555-2971
  • Monroy, Eva
  • Naranjo Vega, Fernando Bernabé|||0000-0002-2119-6749
We present the structural and optical properties of (0001)-oriented nanocolumnar films of InN deposited on c-sapphire substrates by radio-frequency reactive sputtering. It is observed that the column density and dimensions are highly dependent on the growth parameters of the buffer layer. We investigate four buffer layers consisting of (i) 30 nm of low-growth-rate InN, (ii) 30 nm of AlN deposited on the unbiased substrate (us), (iii) 30 nm of AlN deposited on the reverse-biased substrate (bs), and (iv) a 60-nm-thick bilayer consisting of 30-nm-thick bs-AlN deposited on top of 30-nm-thick us-AlN. Differences in the layer nucleation process due to the buffer layer induce variations of the column density in the range of (2.5-16)×109 cm-2, and of the column diameter in the range of 87-176 nm. Best results in terms of mosaicity are obtained using the bs-AlN buffer layer, which leads to a full width at half-maximum of the InN(0002) rocking curve of 1.2°. A residual compressive strain is still present in the nanocolumns. All samples exhibit room temperature photoluminescence emission at ∼1.6 eV, and an apparent optical band gap at ∼1.7 eV estimated from linear optical transmittance measurements., Ministerio de Economía y Competitividad, Comunidad de Madrid, Universidad de Alcalá, European Commission
e_Buah Biblioteca Digital Universidad de Alcalá
Publication Artículo científico (JournalArticle)

InN-based optical waveguides developed by RF sputtering for all-optical applications at 1.55 μm

  • Monteagudo Lerma, Laura
  • Naranjo Vega, Fernando Bernabé|||0000-0002-2119-6749
  • Jiménez Rodríguez, Marco
  • Postigo, P.A.
  • Barrios, E.
  • Corredera Guillén, Pedro
  • González Herráez, Miguel|||0000-0003-2555-2971
We report on the design, fabrication, and optical characterization of InN-based optical waveguides aiming at their application as all-optical limiters at 1.55 $\mu \text{m}$. The InN guiding layers are grown by radio frequency (RF) sputtering on sapphire substrates. Experimental cutback method and nonlinear optical transmittance measurements were performed for the developed devices. The waveguides present nonlinear behavior associated with two photon absorption process. A nonlinear absorption coefficient ranging from $\sim 43$ to 114 cm/GW is estimated from optical measurements. These results open the possibility of using RF sputtering as a low cost and thermally harmless technique for the development and overgrowth of InN-based optical waveguides in future III-nitride all-optical integrated circuits working at telecom wavelengths, Ministerio de Economía y Competitividad, Comunidad de Madrid, Universidad de Alcalá
e_Buah Biblioteca Digital Universidad de Alcalá
Publication Artículo científico (JournalArticle)

A microstructured capillary electrophoresis method for nitrocellulose detection in dynamite

  • Calcerrada Guerreiro, Matías
  • Fernández de la Ossa, María de los Ángeles
  • Roy, Philippe
  • González Herráez, Miguel|||0000-0003-2555-2971
  • García Ruiz, Carmen|||0000-0001-5925-3449
In this article we present a microstructured-capillary electrophoresis method for the determination of minimal amounts of nitrocellulose in dynamite samples. A 6-hole microstructured capillary (MSC) was selected for the method development. First, the hydrodynamic behaviour of the MSC was studied at varying lengths (31, 41 and 51 cm), which had never been studied before. Next, one of the MSC segments (31 cm) was employed to develop a microstructured-capillary electrophoresis method to determine nitrocellulose in dynamite. In a first evaluation, the dynamite derivatization process was investigated to obtain an efficient derivatization yield. Afterwards, the instrumental parameters, more specifically voltage and capillary cartridge temperature, were optimized. Afterwards, the analytical performance of the developed methodology was assessed. Dynamite analyses during a period of 15 days were performed to establish intra-day (10 analyses) and inter-day (40 analyses) precision, obtaining RSDs lower than 6 and 10%, respectively. Besides, RSDs for migration time (<0.5%), peak asymmetry (<3%), resolution (<3.9%) and S/N (<9%) were obtained. Finally, a diluted sample of dynamite was analysed, detecting amounts of nitrocellulose in the order of 220-400 pg., Ministerio de Economía, Industria y Competitividad
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Artículo científico (JournalArticle)

Compound lasing fiber optic ring resonators for sensor sensitivity enhancement

  • Rota Rodrigo, Sergio
  • González Herráez, Miguel
  • López-Amo Sáinz, Manuel
In this work, a new method for increasing simultaneously the sensitivity and interrogation stability of fiberoptic intensity sensors is presented. The configuration is based on a double-coupler ring resonator. On one side, the attenuation sensitivity of the sensor is enhanced by placing it inside a ring resonator. On the other side, the stability of the interrogation method is widely improved by creating an external lasing ring resonator with matched spectral response. The combination of the wavelength selective response of the ring resonator and optical amplification from Er-doped fiber amplifier is used to create different fiber lasers. The resulting lasers present an impressive sensitivity enhancement and a dynamic range increment up to 15 dB. Simultaneously, the instability of the system is reduced to ±0.05 dB. In comparison with systems based on tunable laser interrogation, our method is >100 times more stable and also simpler, as no wavelength tunable elements are required., The authors would like to acknowledge the financial support from the Spanish Ministerio de Educación y Ciencia through projects TEC2010-20224-C02-01, TEC2013-47264-C2-2-R, TEC2012-37958-C02-01 and Innocampus; from the European FEDER funding, ECOAL-MGT SUDOE project and from the European Research Council through Starting Grant U-FINE (Grant No. 307441).
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Artículo científico (JournalArticle)

Slow-light and enhanced sensitivity in a displacement sensor using a lossy fiber-based ring resonator

  • Bravo Acha, Mikel
  • Angulo Vinuesa, X.
  • Martín López, Sonia
  • López-Amo Sáinz, Manuel
  • González Herráez, Miguel
Along the last years, much debate has been done on the efficiency of slow-light phenomena in order to enhance lightmatter interactions, especially for sensing purposes. This improvement could be key to develop more compact and sensitive devices. In this work we develop an all-fiber submicrometric displacement sensor using slow-light sensitivity enhancement in a lossy ring resonator. In the proposed structure the losses produced by the displacement of a mechanic transducer can be translated into strong variations of group index and therefore strong transmittance variations. We show that this effect is strictly related to slow light, and not related to confinement effects or any other., This work was supported by the European Research Council through Starting Grant U-FINE (Grant no. 307441), by the Spanish Ministry of Science and Innovation through projects TEC2010-20224-C02-01, TEC2012-37958-C02-01, Innocampus and the Comunidad de Madrid through project FACTOTEM-2.