Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 6
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Naproxen electrooxidation using carbon paper electrodes modified with reduced graphene oxide and platinum nanoparticles

  • Molina Puerto, Javier|||0000-0003-3378-8271
  • Bonastre Cano, José Antonio|||0000-0002-5068-6608
  • Cases, Francisco|||0000-0001-8105-4489
  • Olcina, L.
[EN] This research study investigates the electrooxidation of naproxen (NPX), an anti-inflammatory pharmaceutical, on modified carbon paper (CP) electrodes. Electrochemical modification of CP electrodes was accomplished with Pt or reduced graphene oxide (RGO)-Pt coatings, resulting in the production of electroactive electrodes. RGO coatings synthesized by cyclic voltammetry (CV) for 10 scans provided the optimal coverage for the CP electrode surface. The deposition of Pt nanoparticles (Pt NPs) on the electrodes (CP or CP-RGO) by CV produced a good electrode surface coverage with 20 synthesis scans. The voltammetric analysis of the electrodes in 230 mg/L NPX solution showed oxidation peaks around 1.0 to 1.2 V. Moreover, the inclusion of RGO in the coating led to an increase in the current density of these oxidation peaks and a decrease of the electrode electron transfer resistance as measured by electrochemical impedance spectroscopy. The electrolysis of NPX in different electrolytes (Na2SO4 and Na2SO4/NaCl) was conducted at 1.4 V, and the removal of NPX was analyzed using high-performance liquid chromatography. The CP-RGO-Pt electrode in Na2SO4/NaCl media showed the fastest NPX degradation kinetics, resulting in a 90 % degradation in only 90 min with low charge consumption (0.07 AhL-1). The smaller size of Pt NPs deposited on CP-RGO, as observed by field emission scanning electron microscopy and transmission electron microscopy, contributed to the higher electrochemical response in CV and a faster kinetic degradation of NPX., This research is part of the Spanish R + D + i contract TED2021-130905B-I00 funded by MCIN/AEI/10.13039/501100011033 and by the European Union NextGenerationEU/PRTR as well as the Red E3Tech Plus: Proyecto Redes de Investigacion de la AEI Network E3Tech PLUS (RED2022-134552-T) project. Funding for open access charge: CRUE-Universitat Politecnica de Valencia. The Electron Microscopy Service of the UPV (Universitat Politecnica de Valencia) is gratefully acknowledged for help with FESEM and EDX characterization.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Electrochemical degradation of micro/nanoplastics in water: recent results

  • Rodrigo, R.
  • Bonastre Cano, José Antonio|||0000-0002-5068-6608
  • Molina Puerto, Javier|||0000-0003-3378-8271
  • Cases, Francisco|||0000-0001-8105-4489
[EN] Microplastics and nanoplastics have emerged as critical environmental contaminants due to their ubiquitous presence, persistence, and potential risks to human health and ecosystems. These particles, derived from the fragmentation of plastic waste, can adsorb other contaminants, penetrate biological barriers, and accumulate in living organisms. Wastewater treatment plants act as both sources and sinks of microplastics and nanoplastics, retaining a significant fraction of these pollutants but failing to remove them completely. In addition, conventional treatment processes can induce the fragmentation of microplastics into nanoplastics, increasing the problem. Given the limited effectiveness of traditional physical, chemical, or biological separation methods, advanced oxidation processes have emerged as promising alternatives. Among them, electrochemical oxidation, based on the in situ generation of reactive oxygen species such as hydroxyl radicals, has demonstrated high efficiency in degrading organic pollutants. This review analyses the most recent advancements in the use of electrochemical oxidation, highlighting the use of boron-doped diamond anodes and other electrochemical configurations. Experimental studies with different operating conditions, combinations with complementary techniques and the impact of electrocatalytic materials on the efficiency of the process are addressed. The reported results demonstrate degradation rates above 90% under specific conditions, without generating toxic by-products, and with reasonable energy consumption. Electrochemical oxidation enables the mineralization of polymeric particles and adapts to different water matrices. Further research at pilot- and industrial-scale is required to optimize operations and validate its long-term feasibility. Overall, electrochemical oxidation is emerging as a strategic tool for advanced wastewater treatment., This research is part of the Spanish R+D+i contract TED2021-130905B-I00 funded by MCIN/ AEI/10.13039/501100011033 and by the European Union NextGenerationEU/PRTR as well as the Red E3Tech Plus: Proyecto Redes de Investigación de la AEI Network E3Tech PLUS (RED2022-134552-T) project. Funding for open access charge: CRUE-Universitat Politècnica de València.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

High surface area modified Ti-felt electrodes for the degradation of polystyrene nanoplastics

  • Rodrigo-Roca, Rubén
  • Bonastre Cano, José Antonio|||0000-0002-5068-6608
  • Molina Puerto, Javier|||0000-0003-3378-8271
  • Cases, Francisco|||0000-0001-8105-4489
[EN] Ti-felt electrodes with high surface area have been used as supports of electroactive coatings (Pt and SnO2-Sb-Pt). The electrodes obtained have been employed for the electrochemical oxidation of polystyrene nanoplastics (NPs) (100 nm) in solution. Voltammetric characterization of the electrodes with Ru(NH3)6Cl3 and K3Fe(CN)6 redox mediators showed a substantial increase in the redox peaks¿ current density compared to the boron-dopeddiamond electrode. For example, this increase was >68-fold for the SnO2-Sb-Pt electrode when using the Ru (NH3)6Cl3 redox mediator. This can be attributed to the enhanced surface area of Ti-felt, composed of 20 m diameter fibers, and the roughness of the electrocatalyst coatings. Voltammetric characterization of Ti-Pt and TiSnO2-Sb-Pt in 0.03 M Na2SO4 media showed an increase in the anodic current density when adding NPs, which would account for a direct mechanism of electrooxidation of the electrode. OH, S2O82, H2O2, and O3 generation were also determined for both types of electrodes. The degradation of NPs was monitored by fluorescence spectroscopy, taking advantage of the fluorescence of styrene. In addition, it was observed that the scattering of the second-order diffraction light (this phenomenon takes place in the diffraction grating of the monochromator) by NPs could also be used to monitor the evolution of the NPs concentration in solution. The electrochemical degradation of polystyrene NPs was faster with SnO2-Sb-Pt modified Ti-felt based electrodes than with the Ptmodified one (reaching 90 % degradation in 100 and 210 min at 25 mA cm 2, respectively). Electrochemical energy consumption per order was also lower for SnO2-Sb-Pt-modified electrodes., This research is part of the Spanish R + D + i contract TED2021-130905B-I00 funded by MCIN/AEI /10.13039/501100011033 and by the European Union NextGenerationEU/PRTR as well as the Red E3Tech Plus: Proyecto Redes de Investigacion ¿ de la AEI Network E3Tech PLUS (RED2022-134552-T) project. Funding for open access charge: CRUE Universitat Polit`ecnica de Val`encia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Electrochemical removal of polystyrene nanoplastics in a filter-press reactor using modified Ti-felt anodes: comparison of flow-through and flow-by configurations

  • Rodrigo-Roca, Rubén
  • Bonastre Cano, José Antonio|||0000-0002-5068-6608
  • Molina Puerto, Javier|||0000-0003-3378-8271
  • Cases, Francisco|||0000-0001-8105-4489
[EN] Ti-felt anodes with high surface area were used as supports for Pt and SnO₂–Sb–Pt electrocatalysts. The anodes were tested in a filter-press electrochemical reactor for the electrooxidation of polystyrene nanoplastics (NPs) at an initial concentration of 100 mg·L⁻¹. Two reactor configurations were evaluated. In the first one (flow-through, F–T), the NP suspension was forced through the porous anode, which acted as a permeable electrode, enhancing contact between the NPs and both the anode surface and the oxidizing species generated in situ. In the second configuration (flow-by, F–B), the NP suspension flowed parallel to the anode surface. At 25 mA·cm⁻², the flow-through configuration substantially outperformed the flow-by configuration. For the Ti–Pt anode, F–T reduced energy consumption by approximately 7-fold and treatment time by about 15-fold relative to F–B. For the Ti–SnO₂–Sb–Pt anode, the corresponding reductions were ~6.5-fold in energy consumption and ~13-fold in treatment time. The influence of current density (50, 25, 12.5, and 5 mA·cm⁻²) was also investigated. For the Ti–Pt electrode operating in the F–T mode at 25 mA·cm⁻², a treatment time of only 40 min was achieved, with a Faradaic efficiency of 62.09% and an electrochemical energy per order (EEO) of 21.91 kW·h·m⁻³·order⁻¹. In contrast, under the F–B configuration at the same current density, the treatment time increased to 600 min, with a Faradaic efficiency of 8.27% and an EEO of 156.57 kW·h·m⁻³·order⁻¹., This research is part of the Spanish R+D+i contract TED2021-130905B-I00 funded by MCIN/AEI /10.13039/501100011033 and by the European Union NextGenerationEU/PRTR as well as the Red E3Tech Plus: Proyecto Redes de Investigación de la AEI Network E3Tech PLUS (RED2022-134552-T) project. Funding for open access charge: CRUE-Universitat Politecnica de Valencia is acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Influence of the doping level of boron-doped diamond electrodes in the electrooxidation of polystyrene nanoplastics

  • Rodrigo-Roca, Rubén
  • Muñoz, Lucía
  • Molina Puerto, Javier|||0000-0003-3378-8271
  • Bonastre Cano, José Antonio|||0000-0002-5068-6608
  • Cases, Francisco|||0000-0001-8105-4489
[EN] Microplastics and nanoplastics have arisen as contaminants of emerging concern due to the wide use of plastics, and the application of boron-doped diamond (BDD) electrodes for their removal is promising. In this study, we report the influence of BDD doping levels (500, 2500, and 10000 ppm B doping) on the electrooxidation of polystyrene nanoplastics (100 nm, 20 mg¿L-1). Different current densities (50, 25, 12.5, and 5 mA¿cm¿ 2 ) have been applied to determine the best electrolysis conditions for each electrode type. In addition, hydroxyl radical (¿OH), persulphate (S2O8 2-), and hydrogen peroxide (H2O2) reactive species have been determined to understand the influence of the species generated on the degradation of NPs. BDD500 electrode presents the fastest degradation of PS NPs at low current densities (12.5 and 5 mA¿cm¿ 2 ), BDD2500 at 25 mA¿cm¿ 2 , and BDD10000 at 50 mA¿cm¿ 2 . Among oxidative species determined, S2O8 2- is the one generated with the highest concentration and seems to command the degradation of PS NPs, since at 25, 12.5, and 5 mA¿cm¿ 2 , the electrodes that produce more S2O8 2- degrade faster PS NPs. At 50 mA¿cm¿ 2 , the differences between the different electrodes were minimal. The highest mineralization (as measured by non-purgeable organic carbon measurements) was obtained for BDD500 at 50, 25, and 12.5 mA¿cm¿ 2 , and BDD2500 at 5 mA¿cm¿ 2 ., This research is part of the Spanish R + D + i contract TED2021-130905B-I00 funded by MCIN/AEI /10.13039/501100011033 and by the European Union NextGenerationEU/PRTR as well as the Red E3Tech Plus: Proyecto Redes de Investigacion ¿ de la AEI Network E3Tech PLUS (RED2022-134552-T) project. Funding for open access charge: CRUEUniversitat Polit`ecnica de Val`encia
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Development and application of an electrolysis cell prototype based on textile electrodes: dyestuff wastewater electrolysis

  • Soler-Micó, Ignacio
  • Orts Maiques, Francisco José|||0000-0001-8254-8042
  • Molina Puerto, Javier|||0000-0003-3378-8271
  • Micó-Vicent, B.|||0000-0001-8845-1495
  • Bonastre Cano, José Antonio|||0000-0002-5068-6608
  • Cases, Francisco|||0000-0001-8105-4489
[EN] This research work studies the development of an electrochemical cell prototype based on textile electrodes for treating wastewater via electrochemical processes. The present prototype proposes a system that offers greater efficiency regarding the size/surface of electrodes in electrolysis processes. This prototype enables the treatment of large volumes of dissolution. Moreover, this prototype could surface modify textile electrodes by an electrochemical process in the same cell, specifically, an electrochemically reduced graphene oxide intermediate layer and an outer layer of electrochemically reduced metal nanoparticles are proposed. Surface modification by reduced graphene oxide increase the textile electrode¿s stability, conductivity, and specific surface, whilst Pt nanoparticles increase electroactivity. Amaranth was selected to validate the use of this prototype in treating emerging pollutants. This is an azoic dye with a simple structure. Various analytical techniques demonstrate that colour removal takes place with an electrical energy consumption of between 0.29 and 4.66 kWh m¿3 (depending on the operational specifications of the electrolysis performed). Once the colour is removed, total organic carbon and chemical oxygen demand decreases by up to 49% and 37%, respectively., This research is part of the Spanish R+D+i contract (TED2021-130905B-I00 funded by MCIN/ AEI/10.13039/501100011033 and the European Union NextGenerationEU/PRTR ). The authors wish to acknowledge the Spanish AEI Research Network (Contract RED2022-134552-T). Chemviron Carbon, who kindly donated the FlexzorbTM FM10 activated carbon fabrics and Funding for open access charge CRUE-Universitat Politècnica de València, are acknowledged too.