Skip to main content

APLICACIONES MEDIOAMBIENTALES Y ENERGETICAS DE LA TECNOLOGIA ELECTROQUIMICA FRENTE A LOS RETOS DEL NEXO AGUA-ENERGIA

RED2022-134552-T

•
Funding agency name Agencia Estatal de Investigación
Funding agency acronym AEI
Program Programa Estatal para Impulsar la Investigación Científico-Técnica y su Transferencia
Subprogram Subprograma Estatal de Generación de Conocimiento
Call Redes Investigación /Redes Excelencia
Call year 2022
State Plan 2021-2023 Plan Estatal de Investigación Científica y Técnica y de Innovación
Beneficiary centre UNIVERSIDAD DE CASTILLA-LA MANCHA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 24
Encontrada(s) 1 página(s)

Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Electrochemical reduction mechanism of 4-nitrobenzyl bromide in ionogel membranes

  • Naeem, Tehreema|||0009-0007-6034-0348
  • Mena Fernández, Silvia|||0000-0002-2800-2388
  • Hernando, Jordi|||0000-0002-1126-4138
  • Guirado, Gonzalo|||0000-0003-2128-7007
Ionic liquid-based electrolytes (ILs) have gained tremendous attention as sustainable, green electrolytes for electrochemical processes due to their negligible vapour pressure and high boiling points. A rising trend is to fabricate solid electrolytes based on ionic liquids to address the risk of leakage associated to liquid electrolytes. These solid electrolytes, which are commonly known as ionogel membranes (IGs), contain the intrinsic properties of ILs, while having excellent mechanical strength. These characteristics make them ideal for investigating reaction mechanisms and facilitating electrosynthesis processes. By providing a stable and conductive environment, ionogels enable precise control and monitoring of electrochemical reactions in solid electrolytes, leading to more accurate and reproducible results. Their application not only enhances our understanding of fundamental electrochemical processes but also paves the way for innovative advancements in electrosynthesis, contributing significantly to the development of new materials and technologies. In this body of research, the reduction mechanism of p-nitrobenzyl bromide (p-NBBr) is studied and disclosed in IG membranes for a first time. We successfully performed a controlled potential electrolysis of p-NBBr in IG membranes, as well as studying two different electrochemical setups to obtain the most optimal configuration. We also demonstrate that the addition of electrolyte additives, such as lithium bis(trifluorometahnesulfonyl)imide (Li TFSI), in the IG composition raises the ionic conductivity of the resulting membrane from 0.15 up to 0.2 mS/cm.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Research data Set de datos (Dataset)

Cell prototype based on textile electrodes for dyestuff wastewater electrolysis [Dataset], Development and application of an electrolysis cell prototype based on textile electrodes: dyestuff wastewater electrolysis

  • Cases, Francisco|||0000-0001-8105-4489
  • Soler Micó, Ignacio
  • Orts Maiques, Francisco José|||0000-0001-8254-8042
  • Bonastre Cano, José Antonio|||0000-0002-5068-6608
  • Molina Puerto, Javier|||0000-0003-3378-8271
  • Micó-Vicent, B.|||0000-0001-8845-1495
[EN] This research work studies the development of an electrochemical cell prototype based on textile electrodes for treating wastewater via electrochemical processes. The present prototype proposes a system that offers greater efficiency regarding the size/surface of electrodes in electrolysis processes. This prototype enables the treatment of large volumes of dissolution. Moreover, this prototype could surface modify textile electrodes by an electrochemical process in the same cell, specifically, an electrochemically reduced graphene oxide intermediate layer and an outer layer of electrochemically reduced metal nanoparticles are proposed. Surface modification by reduced graphene oxide increase the textile electrode’s stability, conductivity, and specific surface, whilst Pt nanoparticles increase electroactivity. Amaranth was selected to validate the use of this prototype in treating emerging pollutants. This is an azoic dye with a simple structure. Various analytical techniques demonstrate that colour removal takes place with an electrical energy consumption of between 0.29 and 4.66 kWh m−3 (depending on the operational specifications of the electrolysis performed). Once the colour is removed, total organic carbon and chemical oxygen demand decreases by up to 49% and 37%, respectively., This research is part of the Spanish R+D+i contract (TED2021-130905B-I00 funded by MCIN/ AEI/10.13039/501100011033 and the “European Union NextGenerationEU/PRTR”). The authors wish to acknowledge the Spanish AEI Research Network (Contract RED2022-134552-T). Chemviron Carbon, who kindly donated the FlexzorbTM FM10 activated carbon fabrics and Funding for open access charge CRUE-Universitat Politècnica de València, are acknowledged too. The authors are grateful for the English revision by John Rawlins and Tim Vickers.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Naproxen electrooxidation using carbon paper electrodes modified with reduced graphene oxide and platinum nanoparticles

  • Molina Puerto, Javier|||0000-0003-3378-8271
  • Bonastre Cano, José Antonio|||0000-0002-5068-6608
  • Cases, Francisco|||0000-0001-8105-4489
  • Olcina, L.
[EN] This research study investigates the electrooxidation of naproxen (NPX), an anti-inflammatory pharmaceutical, on modified carbon paper (CP) electrodes. Electrochemical modification of CP electrodes was accomplished with Pt or reduced graphene oxide (RGO)-Pt coatings, resulting in the production of electroactive electrodes. RGO coatings synthesized by cyclic voltammetry (CV) for 10 scans provided the optimal coverage for the CP electrode surface. The deposition of Pt nanoparticles (Pt NPs) on the electrodes (CP or CP-RGO) by CV produced a good electrode surface coverage with 20 synthesis scans. The voltammetric analysis of the electrodes in 230 mg/L NPX solution showed oxidation peaks around 1.0 to 1.2 V. Moreover, the inclusion of RGO in the coating led to an increase in the current density of these oxidation peaks and a decrease of the electrode electron transfer resistance as measured by electrochemical impedance spectroscopy. The electrolysis of NPX in different electrolytes (Na2SO4 and Na2SO4/NaCl) was conducted at 1.4 V, and the removal of NPX was analyzed using high-performance liquid chromatography. The CP-RGO-Pt electrode in Na2SO4/NaCl media showed the fastest NPX degradation kinetics, resulting in a 90 % degradation in only 90 min with low charge consumption (0.07 AhL-1). The smaller size of Pt NPs deposited on CP-RGO, as observed by field emission scanning electron microscopy and transmission electron microscopy, contributed to the higher electrochemical response in CV and a faster kinetic degradation of NPX., This research is part of the Spanish R + D + i contract TED2021-130905B-I00 funded by MCIN/AEI/10.13039/501100011033 and by the European Union NextGenerationEU/PRTR as well as the Red E3Tech Plus: Proyecto Redes de Investigacion de la AEI Network E3Tech PLUS (RED2022-134552-T) project. Funding for open access charge: CRUE-Universitat Politecnica de Valencia. The Electron Microscopy Service of the UPV (Universitat Politecnica de Valencia) is gratefully acknowledged for help with FESEM and EDX characterization.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Electrochemical degradation of micro/nanoplastics in water: recent results

  • Rodrigo, R.
  • Bonastre Cano, José Antonio|||0000-0002-5068-6608
  • Molina Puerto, Javier|||0000-0003-3378-8271
  • Cases, Francisco|||0000-0001-8105-4489
[EN] Microplastics and nanoplastics have emerged as critical environmental contaminants due to their ubiquitous presence, persistence, and potential risks to human health and ecosystems. These particles, derived from the fragmentation of plastic waste, can adsorb other contaminants, penetrate biological barriers, and accumulate in living organisms. Wastewater treatment plants act as both sources and sinks of microplastics and nanoplastics, retaining a significant fraction of these pollutants but failing to remove them completely. In addition, conventional treatment processes can induce the fragmentation of microplastics into nanoplastics, increasing the problem. Given the limited effectiveness of traditional physical, chemical, or biological separation methods, advanced oxidation processes have emerged as promising alternatives. Among them, electrochemical oxidation, based on the in situ generation of reactive oxygen species such as hydroxyl radicals, has demonstrated high efficiency in degrading organic pollutants. This review analyses the most recent advancements in the use of electrochemical oxidation, highlighting the use of boron-doped diamond anodes and other electrochemical configurations. Experimental studies with different operating conditions, combinations with complementary techniques and the impact of electrocatalytic materials on the efficiency of the process are addressed. The reported results demonstrate degradation rates above 90% under specific conditions, without generating toxic by-products, and with reasonable energy consumption. Electrochemical oxidation enables the mineralization of polymeric particles and adapts to different water matrices. Further research at pilot- and industrial-scale is required to optimize operations and validate its long-term feasibility. Overall, electrochemical oxidation is emerging as a strategic tool for advanced wastewater treatment., This research is part of the Spanish R+D+i contract TED2021-130905B-I00 funded by MCIN/ AEI/10.13039/501100011033 and by the European Union NextGenerationEU/PRTR as well as the Red E3Tech Plus: Proyecto Redes de Investigación de la AEI Network E3Tech PLUS (RED2022-134552-T) project. Funding for open access charge: CRUE-Universitat Politècnica de València.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Amorphous surface modification and scalability of WO3 nanostructures for photoelectrocatalytic degradation of organic pollutants

  • Cifre-Herrando, Mireia|||0000-0002-8800-3585
  • Garcia-Anton, Jose|||0000-0002-0289-1324
  • Roselló-Márquez, Gemma
  • Mais, L.
  • Mascia, M.
[EN] This work explores the use of WO3 nanostructures as an effective solution for the removal of emerging contaminants from water, specifically focusing on the degradation of diethyl phthalate (DEP), a widely recognized environmental pollutant. A key aspect of the study is the scaling of the electrochemically active area and surface modification of WO3 nanostructures, progressing from 0.5 cm2 to 2.5 cm2, followed by a surface reduction treatment that induces amorphization and enhances their photoelectrocatalytic activity after applying a 5-minute reduction treatment. Scaling was further extended to 15 cm2, with the 15 cm2 nanostructures exhibiting the highest DEP degradation rate, achieving a degradation constant of 0.0988 h-1. The study also investigates the effect of key operational parameters such as applied voltage (1 V and 1.5 V), contaminant concentration (10 ppm, 25 ppm and 100 ppm). Reusability was also tested, with optimal conditions identified as 10 ppm DEP, 1 V, and the ability to reuse the nanostructures up to three times. Finally, under these optimal conditions, the degradation of DEP was monitored, leading to the identification of ten intermediate products and the proposal of a degradation pathway, highlighting the potential of WO3 for sustainable and efficient water treatment applications., The authors wish to thank the economic support granted by AEI (PID2019 105844RB-I00/AEI/10.13039/501100011033). M. CifreHerrando acknowledges the Ministerio de Universidades for the predoctoral grant (FPU19/02466). G. Rosello-Marquez is also grateful to UPV for the post-doctoral grant (PAID-10 21) and the grant to support postdoctoral research at UPV (PAID-PD-22). Additionally, funding from the Spanish Research Network E3TECH-PLUS (RED2022 134552-T, MICINN/AEI) is acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Research data Set de datos (Dataset)

Electrooxidation of polystyrene nanoplastics by modified Ti-felt electrodes, High surface area modified Ti-felt electrodes for the degradation of polystyrene nanoplastics

  • Cases, Francisco|||0000-0001-8105-4489
  • Bonastre Cano, José Antonio|||0000-0002-5068-6608
  • Molina Puerto, Javier|||0000-0003-3378-8271
  • Rodrigo Roca, Rubén
[EN] Ti-felt electrodes with high surface area have been used as supports of electroactive coatings (Pt and SnO₂–Sb–Pt). The electrodes obtained have been employed for the electrochemical oxidation of polystyrene nanoplastics (NPs) (100 nm) in solution. Voltammetric characterization of the electrodes with Ru(NH₃)₆Cl₃ and K₃Fe(CN)₆ redox mediators showed a substantial increase in the redox peaks' current density compared to the boron‑doped diamond electrode. For example, this increase was >68‑fold for the SnO₂–Sb–Pt electrode when using the Ru(NH₃)₆Cl₃ redox mediator. This can be attributed to the enhanced surface area of Ti‑felt, composed of 20 μm diameter fibers, and the roughness of the electrocatalyst coatings. Voltammetric characterization of Ti‑Pt and Ti‑SnO₂–Sb–Pt in 0.03 M Na₂SO₄ media showed an increase in the anodic current density when adding NPs, which would account for a direct mechanism of electrooxidation of the electrode. •OH, S₂O₈²⁻, H₂O₂, and O₃ generation were also determined for both types of electrodes. The degradation of NPs was monitored by fluorescence spectroscopy, taking advantage of the fluorescence of styrene. In addition, it was observed that the dispersion of the second‑order diffraction light (this phenomenon takes place in the diffraction grating of the monochromator) by NPs could also be used to monitor the evolution of the NPs concentration in solution. The electrochemical degradation of polystyrene NPs was faster with SnO₂–Sb–Pt modified Ti‑felt‑based electrodes than with the Pt‑modified one (reaching 90 % degradation in 100 and 210 minutes at 25 mA·cm⁻², respectively). Electrochemical energy consumption per order was also lower for SnO₂–Sb–Pt‑modified electrodes., This research is part of the Spanish R+D+i contract TED2021-130905B-I00 funded by MCIN/AEI /10.13039/501100011033 and by the European Union NextGenerationEU/PRTR as well as the Red E3Tech Plus: Proyecto Redes de Investigación de la AEI Network E3Tech PLUS (RED2022-134552-T) project. Funding for open access charge: CRUE-Universitat Politècnica de València. The Electron Microscopy Service of the UPV (Universitat Politècnica de València) is gratefully acknowledged for its help with FESEM, EDX, and TEM characterization.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Surface modification of jute fabrics by reduced graphene oxide-conducting polymer coatings for their application in low-cost and eco-friendly supercapacitors

  • Bonastre Cano, José Antonio|||0000-0002-5068-6608
  • Molina Puerto, Javier|||0000-0003-3378-8271
  • Cases, Francisco|||0000-0001-8105-4489
[EN] In this study, flexible textile supercapacitors were obtained on jute fabrics. Insulating jute fibers were converted into electrically conducting using an optimized reduced graphene oxide (rGO) deposition method. Supercapacitors were made of jute fabric and polypyrrole (PPy) as conducting polymer. rGO improved the electrical behavior of PPy-jute supercapacitors obtained by chemical polymerization. These chemical PPy-jute supercapacitors presented a low surface resistivity (6 & omega;/sq) suitable for subsequent electrochemical polymerization. The best results were obtained for rGO-PPy-jute supercapacitors synthesized by electrochemical polymerization, with capacitance values of 5127 mF cm-2 (117 F g-1) in a 3-electrode system; and1770 mF cm-2, 39.9 F g-1, 250 & mu;W h cm-2 and 1100 & mu;W cm-2 in a 2-electrode system. It is essential to highlight that the jute supercapacitors obtained are eco-friendly, low cost, flexible and with very competitive energy-storage values compared to recent investigations., This research is part of the Spanish R + D + i contract PDC2021- 121617-C22 funded by MCIN/AEI/10.13039/501100011033 and by the "European Union NextGenerationEU/PRTR" as well as the Red E3Tech Plus: Proyecto Redes de Investigacion de la AEI Network E3Tech PLUS (RED2022-134552-T) project. Funding for open access charge: CRUE-Universitat Politecnica de Valencia. Electron Microscopy Service of Universitat Politecnica de Valencia is gratefully acknowledged for help with FESEM microscope.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Research data Set de datos (Dataset)

Surface modification of jute fabrics by rGO-ICP for eco-friendly supercapacitors, Journal of Energy Storage 2023, Surface modification of jute fabrics by reduced graphene oxide-conducting polymer coatings for their application in low-cost and eco-friendly supercapacitors

  • Cases, Francisco|||0000-0001-8105-4489
  • Bonastre Cano, José Antonio|||0000-0002-5068-6608
  • Molina Puerto, Javier|||0000-0003-3378-8271
[EN] In this study, flexible textile supercapacitors were obtained on jute fabrics. Insulating jute fibers were converted into electrically conducting using an optimized reduced graphene oxide (rGO) deposition method. Supercapacitors were made of jute fabric and polypyrrole (PPy) as conducting polymer. rGO improved the electrical behavior of PPy-jute supercapacitors obtained by chemical polymerization. These chemical PPy-jute supercapacitors presented a low surface resistivity (6 Ω/sq) suitable for subsequent electrochemical polymerization. The best results were obtained for rGO-PPy-jute supercapacitors synthesized by electrochemical polymerization, with capacitance values of 5127 mF cm-2 (117 F g-1) in a 3-electrode system; and 1770 mF cm-2, 39.9 F g-1, 250 μW h cm-2 and 1100 μW cm-2 in a 2-electrode system. It is essential to highlight that the jute supercapacitors obtained are eco-friendly, low cost, flexible and with very competitive energy-storage values compared to recent investigations., This research is part of the Spanish R + D + i contract PDC2021-121617-C22 funded by MCIN/AEI/10.13039/501100011033 and by the “European Union NextGenerationEU/PRTR” as well as the Red E3Tech Plus: Proyecto Redes de Investigación de la AEI Network E3Tech PLUS (RED2022-134552-T) project. Funding for open access charge: CRUE-Universitat Politècnica de València. Electron Microscopy Service of Universitat Politècnica de València is gratefully acknowledged for help with FESEM microscope.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Research data Set de datos (Dataset)

Electrooxidation of polystyrene nanoplastics by BDD electrodes [Dataset], Influence of the doping level of boron-doped diamond electrodes in the electrooxidation of polystyrene nanoplastics

  • Cases, Francisco|||0000-0001-8105-4489
  • Rodrigo Roca, Rubén
  • Molina Puerto, Javier|||0000-0003-3378-8271
  • Bonastre Cano, José Antonio|||0000-0002-5068-6608
  • Muñoz Ortuño, Lucía
[EN] Microplastics and nanoplastics have arisen as contaminants of emerging concern due to the wide use of plastics, and the application of boron-doped diamond (BDD) electrodes for their removal is promising. In this study, we report the influence of BDD doping levels (500, 2500, and 10000 ppm B doping) on the electrooxidation of polystyrene nanoplastics (100 nm, 20 mg⋅L-1). Different current densities (50, 25, 12.5, and 5 mA⋅cm-2) have been applied to determine the best electrolysis conditions for each electrode type. In addition, hydroxyl radical (•OH), persulphate (S2O82-), and hydrogen peroxide (H2O2) reactive species have been determined to understand the influence of the species generated on the degradation of NPs. BDD500 electrode presents the fastest degradation of PS NPs at low current densities (12.5 and 5 mA⋅cm-2), BDD2500 at 25 mA⋅cm-2, and BDD10000 at 50 mA⋅cm-2. Among oxidative species determined, S2O82- is the one generated with the highest concentration and seems to command the degradation of PS NPs, since at 25, 12.5, and 5 mA⋅cm-2, the electrodes that produce more S2O82- degrade faster PS NPs. At 50 mA⋅cm-2, the differences between the different electrodes were minimal. The highest mineralization (as measured by non-purgeable organic carbon measurements) was obtained for BDD500 at 50, 25, and 12.5 mA⋅cm-2, and BDD2500 at 5 mA⋅cm-2., This research is part of the Spanish R +D +i contract TED2021-130905B-I00 funded by MCIN/AEI /10.13039/501100011033 and by the European Union NextGenerationEU/PRTR as well as the Red E3Tech Plus: Proyecto Redes de Investigación de la AEI Network E3Tech PLUS (RED2022-134552-T) project. Funding for open access charge: CRUE- Universitat Politècnica de València. The Electron Microscopy Service of the UPV (Universitat Politècnica de València) is gratefully acknowledged for help with TEM and FESEM characterization.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Electrolyte influence on light-assisted electrooxidation of an herbicide employing an Sb-SnO2 electrode coated with a Bi2WO6 photocatalyst

  • Domingo-Torner, Carlos|||0000-0002-3457-581X
  • Pérez-Herranz, Valentín|||0000-0002-4010-0888
  • García Gabaldón, Montserrat|||0000-0003-4254-6733
  • Mestre, S.
[EN] In this work, a series of photoelectrooxidation experiments of the herbicide bentazon (BTZ) under three different electrolytes (Na2SO4, NaCl, and a mixture of both) and using ceramic anodes of Sb-SnO2 coated with a photocatalyst (Bi2WO6) were carried out. Using Na2SO4 as an electrolyte, 74.6 % of BTZ was degraded and 48.5 % was mineralized at 50 mA·cm¿2 without light. Under light application, mineralization increased at this current density by a 31.6 %. This increase was partly due to the activation of persulfates towards the formation of high oxidative SO4radical dot¿ radicals. Using NaCl, up to 85.1 % of BTZ was degraded and 57.2 % was mineralized. Light noticeably fastened the degradation and increased its final value by 8.9 %, otherwise this effect was not as intense in the mineralization. Observed differences between degradation and mineralization under light application were attributed to the formation of photogenerated reactive chlorine species (RCS), which were proven to transform the BTZ faster into different chlorinated molecules, degrading but not mineralizing it. The mixed electrolyte achieved 85.1 % degradation and 54.5 % mineralization at 50 mA·cm¿2 in absence of light. Under light application, degradation was enhanced by a final 6.8 % but the effect was lower than with pure NaCl, due to its lower concentration of the salt and therefore, lesser formation of derivative RCS. Mineralization was also enhanced by a 14.5 % under light application. The mixed electrolyte showed trends in between both pure electrolytes. Scavenging tests for radical dotOHfree using tert-butanol, showed an inhibition of up to 11 % in the presence of light, meaning an important role of this species in the oxidation process. Detection of short-stringed carbon molecules such as formate and acetate confirmed proper oxidation of BTZ, and the detection of chlorate confirmed the formation of RCS. In general, Mineralization Current Efficiency (MCE), energy consumption, and extent of electrochemical combustion (¿) showed improvements with light application, aligning with what was observed during the photoelectrooxidations. These results confirm that these photoanodes are quite sensitive to light, and are capable of oxidizing complex organic molecules, opening to future possibilities in the advanced environmental treatment., This study forms part of the ThinkInAzul programme and was supported by MCIN with funding from European Union NextGenerationEU (PRTR-C17.I1) and by Generalitat Valenciana (GVA-THINKINAZUL/2021/013; principle investigator: V. Perez-Herranz, Universitat Politecnica de Valencia), and the Spanish Research Network E3TECHPLUS (RED2022-134552-T, MICINN/AEI) for their financial support.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Research data Set de datos (Dataset)

Electrochemical removal of polystyrene nanoplastics in a filter-press reactor using modified Ti-felt anodes [Dataset]

  • Cases, Francisco|||0000-0001-8105-4489
  • Molina Puerto, Javier|||0000-0003-3378-8271
  • Bonastre Cano, José Antonio|||0000-0002-5068-6608
  • Rodrigo Roca, Rubén
Ti-felt anodes, with high surface area, have been used as supports of Pt and SnO2-Sb-Pt electrocatalysts. Anodes have been applied in a filter-press electrochemical reactor for the electrooxidation of polystyrene nanoplastics (NPs) (100 mg·L-1). Two types of configurations have been used. In the first, the solution with NPs flows through the anode, taking advantage of its porosity (acting as a sort of membrane) to enhance the contact of NPs with the anode and the oxidative species generated. In the second configuration, the solution of NPs flows parallel to the anode, and the NPs flow parallel to it. Comparing both configurations at 25 mA·cm-2, for the Ti-Pt anode, the flow-through configuration decreases energy consumption by ~7-fold and treatment time by ~15-fold when compared to the flow-by configuration. For Ti-SnO2-Sb-Pt anode, ratios of ~6.5-fold and ~13-fold were obtained, respectively. Moreover, the effect of the current density (50, 25, 12.5, and 5 mA·cm-2) was studied. For the Ti-Pt electrode, a treatment time of only 40 minutes was achieved at a current density of 25 mA·cm-2 with the F-T configuration, with a faradaic efficiency of 62.09 %, and electrochemical energy per order (EEO) of 21.91 kW·h·m-3·order-1. In the case of the F-B configuration at 25 mA·cm-2 the treatment time increases until 600 min, with a faradaic efficiency of 8.27 % and EEO of 156.57 kW·h·m- 3·order-1., This research is part of the Spanish R+D+i contract TED2021-130905B-I00 funded by MCIN/AEI /10.13039/501100011033 and by the European Union NextGenerationEU/PRTR as well as the Red E3Tech Plus: Proyecto Redes de Investigación de la AEI Network E3Tech PLUS (RED2022-134552-T) project. Funding for open access charge: CRUE-Universitat Politècnica de València. The Electron Microscopy Service of the UPV (Universitat Politècnica de València) is gratefully acknowledged for its help with FESEM, EDX, TEM, and XRM characterization.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

High surface area modified Ti-felt electrodes for the degradation of polystyrene nanoplastics

  • Rodrigo-Roca, Rubén
  • Bonastre Cano, José Antonio|||0000-0002-5068-6608
  • Molina Puerto, Javier|||0000-0003-3378-8271
  • Cases, Francisco|||0000-0001-8105-4489
[EN] Ti-felt electrodes with high surface area have been used as supports of electroactive coatings (Pt and SnO2-Sb-Pt). The electrodes obtained have been employed for the electrochemical oxidation of polystyrene nanoplastics (NPs) (100 nm) in solution. Voltammetric characterization of the electrodes with Ru(NH3)6Cl3 and K3Fe(CN)6 redox mediators showed a substantial increase in the redox peaks¿ current density compared to the boron-dopeddiamond electrode. For example, this increase was >68-fold for the SnO2-Sb-Pt electrode when using the Ru (NH3)6Cl3 redox mediator. This can be attributed to the enhanced surface area of Ti-felt, composed of 20 m diameter fibers, and the roughness of the electrocatalyst coatings. Voltammetric characterization of Ti-Pt and TiSnO2-Sb-Pt in 0.03 M Na2SO4 media showed an increase in the anodic current density when adding NPs, which would account for a direct mechanism of electrooxidation of the electrode. OH, S2O82, H2O2, and O3 generation were also determined for both types of electrodes. The degradation of NPs was monitored by fluorescence spectroscopy, taking advantage of the fluorescence of styrene. In addition, it was observed that the scattering of the second-order diffraction light (this phenomenon takes place in the diffraction grating of the monochromator) by NPs could also be used to monitor the evolution of the NPs concentration in solution. The electrochemical degradation of polystyrene NPs was faster with SnO2-Sb-Pt modified Ti-felt based electrodes than with the Ptmodified one (reaching 90 % degradation in 100 and 210 min at 25 mA cm 2, respectively). Electrochemical energy consumption per order was also lower for SnO2-Sb-Pt-modified electrodes., This research is part of the Spanish R + D + i contract TED2021-130905B-I00 funded by MCIN/AEI /10.13039/501100011033 and by the European Union NextGenerationEU/PRTR as well as the Red E3Tech Plus: Proyecto Redes de Investigacion ¿ de la AEI Network E3Tech PLUS (RED2022-134552-T) project. Funding for open access charge: CRUE Universitat Polit`ecnica de Val`encia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Electrochemical removal of polystyrene nanoplastics in a filter-press reactor using modified Ti-felt anodes: comparison of flow-through and flow-by configurations

  • Rodrigo-Roca, Rubén
  • Bonastre Cano, José Antonio|||0000-0002-5068-6608
  • Molina Puerto, Javier|||0000-0003-3378-8271
  • Cases, Francisco|||0000-0001-8105-4489
[EN] Ti-felt anodes with high surface area were used as supports for Pt and SnO₂–Sb–Pt electrocatalysts. The anodes were tested in a filter-press electrochemical reactor for the electrooxidation of polystyrene nanoplastics (NPs) at an initial concentration of 100 mg·L⁻¹. Two reactor configurations were evaluated. In the first one (flow-through, F–T), the NP suspension was forced through the porous anode, which acted as a permeable electrode, enhancing contact between the NPs and both the anode surface and the oxidizing species generated in situ. In the second configuration (flow-by, F–B), the NP suspension flowed parallel to the anode surface. At 25 mA·cm⁻², the flow-through configuration substantially outperformed the flow-by configuration. For the Ti–Pt anode, F–T reduced energy consumption by approximately 7-fold and treatment time by about 15-fold relative to F–B. For the Ti–SnO₂–Sb–Pt anode, the corresponding reductions were ~6.5-fold in energy consumption and ~13-fold in treatment time. The influence of current density (50, 25, 12.5, and 5 mA·cm⁻²) was also investigated. For the Ti–Pt electrode operating in the F–T mode at 25 mA·cm⁻², a treatment time of only 40 min was achieved, with a Faradaic efficiency of 62.09% and an electrochemical energy per order (EEO) of 21.91 kW·h·m⁻³·order⁻¹. In contrast, under the F–B configuration at the same current density, the treatment time increased to 600 min, with a Faradaic efficiency of 8.27% and an EEO of 156.57 kW·h·m⁻³·order⁻¹., This research is part of the Spanish R+D+i contract TED2021-130905B-I00 funded by MCIN/AEI /10.13039/501100011033 and by the European Union NextGenerationEU/PRTR as well as the Red E3Tech Plus: Proyecto Redes de Investigación de la AEI Network E3Tech PLUS (RED2022-134552-T) project. Funding for open access charge: CRUE-Universitat Politecnica de Valencia is acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Research data Set de datos (Dataset)

Electrochemical degradation of Naproxen by carbon paper electrodes coated by RGO and Pt, Naproxen electrooxidation using carbon paper electrodes modified with reduced graphene oxide and platinum nanoparticles

  • Molina Puerto, Javier|||0000-0003-3378-8271
  • Bonastre Cano, José Antonio|||0000-0002-5068-6608
  • Cases, Francisco|||0000-0001-8105-4489
  • Olcina Doménech, Laura
This research study investigates the electrooxidation of naproxen (NPX), an anti-inflammatory pharmaceutical, on modified carbon paper (CP) electrodes. Electrochemical modification of CP electrodes was accomplished with Pt or reduced graphene oxide (RGO)-Pt coatings, resulting in the production of electroactive electrodes. RGO coatings synthesized by cyclic voltammetry (CV) for 10 scans provided the optimal coverage for the CP electrode surface. The deposition of Pt nanoparticles (Pt NPs) on the electrodes (CP or CP-RGO) by CV produced a good electrode surface coverage with 20 synthesis scans. The voltammetric analysis of the electrodes in 230 mg/L NPX solution showed oxidation peaks around 1.0 to 1.2 V. Moreover, the inclusion of RGO in the coating led to an increase in the current density of these oxidation peaks and a decrease of the electrode electron transfer resistance as measured by electrochemical impedance spectroscopy. The electrolysis of NPX in different electrolytes (Na2SO4 and Na2SO4/NaCl) was conducted at 1.4 V, and the removal of NPX was analyzed using high-performance liquid chromatography. The CP-RGO-Pt electrode in Na2SO4/NaCl media showed the fastest NPX degradation kinetics, resulting in a 90 % degradation in only 90 min with low charge consumption (0.07 A⋅h⋅L-1). The smaller size of Pt NPs deposited on CP-RGO, as observed by field emission scanning electron microscopy and transmission electron microscopy, contributed to the higher electrochemical response in CV and a faster kinetic degradation of NPX., This research is part of the Spanish R + D + i contract TED2021-130905B-I00 funded by MCIN/AEI/10.13039/501100011033 and by the European Union NextGenerationEU/PRTR as well as the Red E3Tech Plus: Proyecto Redes de Investigaci´on de la AEI Network E3Tech PLUS (RED2022-134552-T) project. Funding for open access charge: CRUE Universitat Polit`ecnica de Val`encia. The Electron Microscopy Service of the UPV (Universitat Polit`ecnica de Val`encia) is gratefully acknowledged for help with FESEM and EDX characterization.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Influence of the doping level of boron-doped diamond electrodes in the electrooxidation of polystyrene nanoplastics

  • Rodrigo-Roca, Rubén
  • Muñoz, Lucía
  • Molina Puerto, Javier|||0000-0003-3378-8271
  • Bonastre Cano, José Antonio|||0000-0002-5068-6608
  • Cases, Francisco|||0000-0001-8105-4489
[EN] Microplastics and nanoplastics have arisen as contaminants of emerging concern due to the wide use of plastics, and the application of boron-doped diamond (BDD) electrodes for their removal is promising. In this study, we report the influence of BDD doping levels (500, 2500, and 10000 ppm B doping) on the electrooxidation of polystyrene nanoplastics (100 nm, 20 mg¿L-1). Different current densities (50, 25, 12.5, and 5 mA¿cm¿ 2 ) have been applied to determine the best electrolysis conditions for each electrode type. In addition, hydroxyl radical (¿OH), persulphate (S2O8 2-), and hydrogen peroxide (H2O2) reactive species have been determined to understand the influence of the species generated on the degradation of NPs. BDD500 electrode presents the fastest degradation of PS NPs at low current densities (12.5 and 5 mA¿cm¿ 2 ), BDD2500 at 25 mA¿cm¿ 2 , and BDD10000 at 50 mA¿cm¿ 2 . Among oxidative species determined, S2O8 2- is the one generated with the highest concentration and seems to command the degradation of PS NPs, since at 25, 12.5, and 5 mA¿cm¿ 2 , the electrodes that produce more S2O8 2- degrade faster PS NPs. At 50 mA¿cm¿ 2 , the differences between the different electrodes were minimal. The highest mineralization (as measured by non-purgeable organic carbon measurements) was obtained for BDD500 at 50, 25, and 12.5 mA¿cm¿ 2 , and BDD2500 at 5 mA¿cm¿ 2 ., This research is part of the Spanish R + D + i contract TED2021-130905B-I00 funded by MCIN/AEI /10.13039/501100011033 and by the European Union NextGenerationEU/PRTR as well as the Red E3Tech Plus: Proyecto Redes de Investigacion ¿ de la AEI Network E3Tech PLUS (RED2022-134552-T) project. Funding for open access charge: CRUEUniversitat Polit`ecnica de Val`encia
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

A Macroscopic Interpretation of the Correlation between Electrical Percolation and Mechanical Properties of Poly-(Ethylene Vinyl Acetate)/Zn Composites

  • Agrisuelas, Jerónimo
  • García-Jareño, José J.
  • Vicente, Francisco
  • Balart, Rafael|||0000-0001-5670-7126
  • López-Martínez, Juan|||0000-0001-6904-2282
[EN] Elastic composites were prepared using a procedure involving hot plates and zinc powder that was directly dispersed into an EVA matrix. The correlation between the zinc content and the conductive properties of the material was studied via impedance spectroscopy, the thermal properties of the material were studied via differential calorimetry and the mechanical properties of the composites were studied via tensile strength curves, representing an important advancement in the characterization of this type of composite material. The composites¿ tensile strength and elongation at break decrease with the addition of filler since zinc particles act as stress-concentrating centres, while the composites¿ hardness and Young¿s modulus increase because of an increase in the stiffness of the material. The AC perturbation across the EVA/Zn composites was characterized using an RC parallel equivalent circuit that allowed us to easily measure their resistivity (¿p) and permittivity (¿ p). The dependence of these electrical magnitudes on the zinc content is correlated with their mechanical properties across the characteristic time constant ¿p = ¿p·¿ p of this equivalent circuit. The dependence of the mechanical and electrical magnitudes on the zinc content is consistent with the formation of percolation clusters. The addition of graphite particles increases their potential performance. Three possible mechanisms for the electrical transport of the ac-perturbation across the EVA/Zn composites have been identified. Chemical corrosion in acid media causes the loss of zinc surface particles, but their bulk physical properties practically remain constant., Spanish E3TECH-PLUS Research Network (RED2022-134552-T), MICINN/AEI. This research is a part of the grant PID2020-116496RB-C22 funded by MCIN/AEI/10.13039/5 01100011033 and the European Union Next Generation EU /PRTR.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

EIS Behavior of Polyethylene plus Graphite Composite Considered as an Approximation to an Ensemble of Microelectrodes

  • Navarro-Laboulais, J.|||0000-0001-6347-5407
  • García-Jareño, José Juan
  • Agrisuelas, Jerónimo
  • Vicente, Francisco
[EN] The electrical percolation of alternating current through two-phase polyethylene/graphite composite electrodes with different contents of graphite microparticles immersed in aqueous KCl solutions has been studied. Above the graphite content of the first percolation threshold, the electrochemical impedance response of this electrode is associated with an equivalent circuit of resistance Ru in series with a constant phase element (CPE). An insulator material + conducting filler model is proposed in which the electroactive surface is considered as the intersection of the percolation cluster through the solid and the cluster associated with the interfacial region. CPE is analyzed assuming a distribution of microcapacitors of the graphite particles in contact with the dielectric solution and inside the dielectric polymeric phase., Thanks to the support of the Spanish Network of Excellence Environmental and Energy Applications of Electrochemical Technology. MICINN/AEI: RED2022-134552-T.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Structural and electrochemical characterization of modified WO3 nanostructures for lithium-ion battery anodes

  • Cifre-Herrando, Mireia|||0000-0002-8800-3585
  • Garcia-Anton, Jose|||0000-0002-0289-1324
  • Roselló-Márquez, Gemma
[EN] This research explores the electrochemical performance of tungsten trioxide (WO3) nanostructures as anodes in lithium-ion batteries, with a focus on the impact of synthesis modifications. Three types of WO3 nanostructures have been synthesized: basic (B-WO3), isopropanol-modified (Isop-WO3), and molybdenum-doped (Mo-WO3). Characterization was performed using Field Emission Scanning Electron Microscopy, X-ray Diffraction, and X-ray Photoelectron Spectroscopy to analyze their structural and chemical properties. Electrochemical tests were carried out to the nanostructures, showing that modifications in the electrolyte composition significantly enhanced the electrochemical properties of WO3 nanostructures. Particularly, the incorporation of isopropanol and molybdenum into the synthesis process led to nanostructures with increased donor density and enhanced electrical conductivity, thereby improving the overall electrochemical performance of the nanostructures. Finally, lithium-ion batteries were fabricated using the nanostructures as anode and their performance was evaluated. Electrochemical assessments included Cyclic Voltammetry, Electrochemical Impedance Spectrocopy and Charge-Discharge tests. The hybrid Mo-WO3 nanostructure exhibited the best performance, showing lower charge transfer resistance and greater structural stability, attributed to molybdenum's beneficial effects. These findings suggest that tailored nanostructure synthesis can significantly enhance lithium-ion battery efficiency, contributing to the progression of advanced energy storage solutions., The authors wish to thank the economic support granted by Ministerio de Ciencia e Innovacion (PID2019-105844RB-I00/AEI/10.13039/501100011033) . M. Cifre-Herrando acknowledges the Ministerio de Universidades for the pre-doctoral grant (FPU19/02466) . G. Rosello -Marquez is also grateful to UPV for the post-doctoral grant (PAID-10-21) and the grant to support postdoctoral research at UPV (PAID-PD-22) . The authors wish to thank the project co-funded by the FEDER operational program 2014-2020 of the Comunitat Valenciana (IDIFEDER/18/044) for the financial funding. Additionally, funding from the Spanish Research Network E3TECH-PLUS (RED2022-134552-T, MICINN/AEI) is acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Tesis doctoral (DoctoralThesis)

Nanotecnología con WO3 y aplicaciones: Degradación fotoelectroquímica de disruptores endocrinos y ánodos avanzados para baterías de ion de litio

  • Cifre-Herrando, Mireia|||0000-0002-8800-3585
[ES] La presente Tesis Doctoral se centra en la síntesis, caracterización y optimización de nanoestructuras de óxido de wolframio (WO3) y nanoestructuras híbridas de WO3-MoO3 mediante anodizado electroquímico. Estas nanoestructuras se emplean como fotocatalizadores para la degradación de contaminantes y como ánodos para baterías de ion de litio. El WO3 destaca por sus propiedades semiconductoras, ópticas y eléctricas excepcionales. En aplicaciones medioambiental, las nanoestructuras de WO3 son de gran interés para la fotoelectrocatalisis, un proceso prometedor para la degradación de contaminantes en el agua. El WO3 destaca como fotoánodo debido a su fotoestabilidad, alta conductividad eléctrica y capacidad de absorción de la luz visible. En el campo energético, el WO3 muestra un gran potencial como ánodo en baterías de ion de litio ya que su estructura cristalina permite la inserción y extracción eficiente de iones de litio, mejorando la capacidad de almacenamiento y la durabilidad de las baterías gracias a su estabilidad electroquímica. Para mejorar las nanoestructuras de WO3, se ha estudiado su combinación con óxido de molibdeno (MoO3). El molibdeno, con propiedades químicas y estructurales similares al wolframio, facilita la deposición efectiva en las nanoestructuras de WO3, ajusta el ancho de banda prohibida, mejora la conductividad, la difusión iónica y reduce la recombinación de portadores de carga. Esta combinación de óxidos resulta en una mayor eficiencia electroquímica, haciendo de las nanoestructuras híbridas WO3-MoO3 una solución prometedora para aplicaciones energéticas. En primer lugar, se sintetizaron las nanoestructuras de WO3, estudiando la influencia de la temperatura de calentamiento tras la síntesis y la adición de disolventes en el electrolito de síntesis. La temperatura óptima fue de 600 °C, obteniendo nanoestructuras cristalinas con excelentes propiedades fotoelectroquímicas. Además, se demuestra que la incorporación de disolventes en el electrolito de síntesis influye significativamente en las propiedades de las nanoestructuras, obteniendo que la adición de un 50 % de isopropanol en el electrolito mejora notablemente sus propiedades electroquímicas. En segundo lugar, se sintetizaron nanoestructuras híbridas de WO3- MoO3·añadiendo diferentes concentraciones de molibdato al electrolito de síntesis. La concentración de 0,1 M de molibdato produjo nanoestructuras con propiedades electroquímicas superiores, destacándolas como prometedoras para su uso como ánodo en baterías. Las nanoestructuras fueron exhaustivamente caracterizadas morfológica, estructural, química, electroquímica y fotoelectroquímicamente. Por último, las nanoestructuras con mejores propiedades fotoelectroquímicas y electroquímicas se emplearon como ánodo en aplicaciones medioambientales y energéticas, respectivamente. En el ámbito medioambiental, se evaluó la eficiencia de las nanoestructuras en la degradación de disruptores endocrinos pertenecientes a diferentes familias químicas, así como sus mezclas y su toxicidad. Las nanoestructuras de WO3 demostraron ser efectivas, logrando una degradación del 100 % de pesticidas, parabenos y fenoles en menos de 4 horas. Sin embargo, la técnica no fue eficiente para eliminar ftalatos, generando productos finales más tóxicos. En el ámbito energético, se estudió el rendimiento de las nanoestructuras como ánodos en baterías de ion de litio, considerando también el impacto del electrolito. La nanoestructura híbrida WO3-MoO3 mostró el mejor rendimiento cuando se utilizó un electrolito que combinaba bisoxalato borato de litio (LiBOB) con aditivos y solventes adicionales. Este trabajo ofrece una contribución significativa al desarrollo de soluciones sostenibles para problemas medioambientales y energéticos, subrayando el potencial de las nanoestructuras de WO3 y WO3-MoO3., [CA] La present Tesi Doctoral se centra en la síntesi, caracterització i optimització de nanoestructures d'òxid de wolframi (WO3) i nanoestructures híbrides de WO3-MoO3 mitjançant anodització electroquímica. Aquestes nanoestructures s'utilitzen com a fotocatalitzadors per a la degradació de contaminants i com a ànodes per a bateries d'ió de liti. El WO3 destaca per les seues propietats semiconductores, òptiques i elèctriques excepcionals. En aplicacions mediambientals, les nanoestructures de WO3 són de gran interès per a la fotoelectrocatalisi, un procés prometedor per a la degradació de contaminants en l'aigua. El WO3 destaca com a fotoànode per la seua fotoestabilitat, alta conductivitat elèctrica i capacitat d'absorció de la llum visible. En el camp energètic, el WO3 mostra un gran potencial com a ànode en bateries d'ió de liti ja que la seua estructura cristal·lina permet la inserció i extracció eficient d'ions de liti, millorant la capacitat d'emmagatzematge i la durabilitat de les bateries gràcies a la seua estabilitat electroquímica. Per a millorar les nanoestructures de WO3, s'ha estudiat la seua combinació amb òxid de molibdè (MoO3). El molibdè, amb propietats químiques i estructurals similars al wolframi, facilita la deposició efectiva en les nanoestructures de WO3, ajusta l'amplada de banda prohibida, millora la conductivitat, la difusió iònica i redueix la recombinació de portadors de càrrega. Això resulta en una major eficiència electroquímica, fent de les nanoestructures híbrides WO3-MoO3 una solució prometedora per a aplicacions energètiques. En primer lloc, es van sintetitzar les nanoestructures de WO3, estudiant la influència de la temperatura de calentament després de la síntesi i l'addició de dissolvents en l'electròlit de síntesi. La temperatura òptima va ser de 600 °C, obtenint nanoestructures cristal·lines amb excel·lents propietats fotoelectroquímiques. A més, es demostra que la incorporació de dissolvents en l'electròlit de síntesi influeix significativament en les propietats de les nanoestructures, obtenint que l'addició d'un 50 % d'isopropanol en l'electròlit millora notablement les seues propietats electroquímiques. En segon lloc, es van sintetitzar nanoestructures híbrides de WO3-MoO3 afegint diferents concentracions de molibdat a l'electròlit de síntesi. La concentració de 0,1 M de molibdat va produir nanoestructures amb propietats electroquímiques superiors, destacant-les com a prometedores per al seu ús com a ànode en bateries. Les nanoestructures van ser exhaustivament caracteritzades morfològicament, estructuralment, químicament, electroquímicament i fotoelectroquímicament. Finalment, les nanoestructures amb millors propietats fotoelectroquímiques i electroquímiques s'utilizaren com a ànode en aplicacions mediambientals i energètiques, respectivament. En l'àmbit mediambiental, s'avaluà l'eficiència de les nanoestructures en la degradació de disruptors endocrins pertanyents a diferents famílies químiques, així com una mescla d'ells i la seua toxicitat. Les nanoestructures de WO3 demostraren ser efectives, aconseguint una degradació del 100 % de pesticides, parabens i fenols en menys de 4 hores. No obstant això, la tècnica no va ser eficient per a eliminar ftalats, generant productes finals més tòxics. En l'àmbit energètic, s'estudià el rendiment de les nanoestructures com a ànodes en bateries d'ió de liti, considerant també l'impacte de l'electròlit. La nanoestructura híbrida WO3-MoO3 mostrà el millor rendiment quan s'utilitzà un electròlit que combinava bis(oxalat)borat de liti (LiBOB) amb additius i dissolvents addicionals. Aquest treball ofereix una contribució significativa al desenvolupament de solucions sostenibles per a problemes mediambientals i energètics, subratllant el potencial de les nanoestructures de WO3 i WO3-MoO3., [EN] This Doctoral Thesis focuses on the synthesis, characterization, and optimization of tungsten oxide (WO3) nanostructures and hybrid WO3-MoO3 nanostructures through electrochemical anodization. These nanostructures are used as photocatalysts for contaminant degradation and as anodes for lithium-ion batteries. WO3 stands out for its exceptional semiconductor, optical, and electrical properties. In environmental applications, WO3 nanostructures are of great interest for photoelectrocatalysis, a promising process for contaminant degradation in water. WO3 is highly effective as a photoanode due to its photostability, high electrical conductivity, and visible light absorption capacity. In the energy field, WO3 shows great potential as an anode in lithium-ion batteries because its crystalline structure allows efficient insertion and extraction of lithium ions, improving storage capacity and battery durability thanks to its electrochemical stability. To improve WO3 nanostructures, their combination with molybdenum oxide (MoO3) has been studied. Molybdenum, with chemical and structural properties similar to tungsten, facilitates effective deposition in WO3 nanostructures, adjusts the bandgap, improves conductivity, ionic diffusion, and reduces charge carrier recombination. This results in greater electrochemical efficiency, making hybrid WO3-MoO3 nanostructures a promising solution for energy applications. Firstly, WO3 nanostructures were synthesized, studying the influence of the annealing temperature and the addition of solvents to the synthesis electrolyte. The optimal temperature was 600 °C, obtaining crystalline nanostructures with excellent photoelectrochemical properties. Additionally, it was demonstrated that the incorporation of solvents in the synthesis electrolyte significantly influences the properties of the nanostructures, showing that the addition of 50 % isopropanol in the electrolyte notably improves their electrochemical properties. Secondly, hybrid WO3-MoO3 nanostructures were synthesized by adding different concentrations of molybdate to the synthesis electrolyte. The concentration of 0.1 M molybdate produced nanostructures with superior electrochemical properties, making them promising for use as anodes in batteries. The nanostructures were exhaustively characterized morphologically, structurally, chemically, electrochemically, and photoelectrochemically. Finally, the nanostructures with the best photoelectrochemical and electrochemical properties were used as anodes in environmental and energy applications, respectively. In the environmental field, the efficiency of the nanostructures in the degradation of endocrine disruptors from different chemical families, as well as their mixtures and toxicity, was evaluated. WO3 nanostructures proved to be effective, achieving 100 % degradation of pesticides, parabens, and phenols in less than 4 hours. However, the technique was not efficient in eliminating phthalates, generating more toxic final products. In the energy field, the performance of the nanostructures as anodes in lithium-ion batteries was studied, also considering the impact of the electrolyte. The hybrid WO3-MoO3 nanostructure showed the best performance when an electrolyte combining Lithium bis(oxalate)borate (LiBOB) with additional additives and solvents was used. This work offers a significant contribution to the development of sustainable solutions for environmental and energy problems, highlighting the potential of WO3 and WO3-MoO3 nanostructures., Agradezco al Ministerio de Universidades por la ayuda predoctoral recibida para la realización de la presente Tesis Doctoral (FPU19/02466). También al Ministerio de Economía, Industria y Competitividad, por la concesión de los proyectos CTQ2016-79203-R (2016) y PID2019-105844RB-I00 (2019) en los cuales he podido participar durante la Tesis Doctoral. Además, agradezco la financiación a la Red Española de Investigación E3TECH-PLUS (RED2022- 134552-T, MICINN/AEI).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Development and application of an electrolysis cell prototype based on textile electrodes: dyestuff wastewater electrolysis

  • Soler-Micó, Ignacio
  • Orts Maiques, Francisco José|||0000-0001-8254-8042
  • Molina Puerto, Javier|||0000-0003-3378-8271
  • Micó-Vicent, B.|||0000-0001-8845-1495
  • Bonastre Cano, José Antonio|||0000-0002-5068-6608
  • Cases, Francisco|||0000-0001-8105-4489
[EN] This research work studies the development of an electrochemical cell prototype based on textile electrodes for treating wastewater via electrochemical processes. The present prototype proposes a system that offers greater efficiency regarding the size/surface of electrodes in electrolysis processes. This prototype enables the treatment of large volumes of dissolution. Moreover, this prototype could surface modify textile electrodes by an electrochemical process in the same cell, specifically, an electrochemically reduced graphene oxide intermediate layer and an outer layer of electrochemically reduced metal nanoparticles are proposed. Surface modification by reduced graphene oxide increase the textile electrode¿s stability, conductivity, and specific surface, whilst Pt nanoparticles increase electroactivity. Amaranth was selected to validate the use of this prototype in treating emerging pollutants. This is an azoic dye with a simple structure. Various analytical techniques demonstrate that colour removal takes place with an electrical energy consumption of between 0.29 and 4.66 kWh m¿3 (depending on the operational specifications of the electrolysis performed). Once the colour is removed, total organic carbon and chemical oxygen demand decreases by up to 49% and 37%, respectively., This research is part of the Spanish R+D+i contract (TED2021-130905B-I00 funded by MCIN/ AEI/10.13039/501100011033 and the European Union NextGenerationEU/PRTR ). The authors wish to acknowledge the Spanish AEI Research Network (Contract RED2022-134552-T). Chemviron Carbon, who kindly donated the FlexzorbTM FM10 activated carbon fabrics and Funding for open access charge CRUE-Universitat Politècnica de València, are acknowledged too.
Investigo. Repositorio Institucional de la Universidade de Vigo
Publication Artículo científico (JournalArticle)

Spinel high-entropy oxides as powerful electrocatalysts for degradation of recalcitrant organic pollutant

  • Bernárdez Rodas, Nuria
  • Barreiro Xardon, Xan
  • Pazos Currás, Marta María
  • Rosales Villanueva, Emilio
  • Sanromán Braga, María Ángeles
In this work a high entropy spinel oxide xerogel (X_HEO), (MnCoFeNi)₃O₄, was synthesized and proposed as a feasible heterogeneous catalyst for electrochemical degradation process. The physicochemical analysis allowed the identification of a structure belonging to the Fd-3 m group and crystalline phases of Fe, Co, Ni, and Mn were detected. A high catalytic activity based on its electrochemical properties was also observed, with an η10 of 307 mV, a Tafel slope of 35.12 mV/dec, and enhanced charge transfer kinetics. The performance of X_HEO as a heterogeneous catalyst was evaluated in the electrooxidation of Rhodamine B and the treatment conditions optimized. The reaction kinetics in the presence of X_HEO increased 2.9 times compared to a process in its absence, attaining 96.67 % removal in 30 min at a current density of 1.6 mA/cm². The reaction mechanism was found to follow a non-radical pathway, dominated by the electrochemical activation of high-valence oxo-metal specie, as supported by XPS analysis and scavenger experiments. Likewise, TOC analysis revealed a mineralization of 91.51 % in 240 min, and the eco toxicity of the final sample was reduced by a factor of 26 times compared to the initial value. X_HEO also showed high electrocatalytic degradation capabilities for pesticides. In particular, total degradation of pymetrozine was reached in just 15 min, with a 45.73 % reduction in TOC by the end of the treatment and the detection of short-chain carboxylic acids confirmed the mineralization process. X_HEO proved to have great potential as a heterogeneous catalyst in electrooxidation treatment and also as sustainable and energy-efficient alternative for the removal of recalcitrant pollutants., Agencia Estatal de Investigación | Ref. TED2021-129590A-I00, Agencia Estatal de Investigación | Ref. PID2023-146133NB-I00, Xunta de Galicia | Ref. ED431C 2025/47, Agencia Estatal de Investigación | Ref. RED2022-134552-T, Xunta de Galicia | Ref. ED481A 2025/046, Universidade de Vigo/CISUG
Investigo. Repositorio Institucional de la Universidade de Vigo
Publication Artículo científico (JournalArticle)

Laser-activated potato peel-derived catalysts for enhanced oxygen evolution reaction

  • Díez Sarabia, Aida Maria
  • Chiussi , Stefano
  • Pazos Currás, Marta María
  • Sanromán Braga, María Ángeles
Oxygen evolution reaction (OER) is the rate-limiting step of the overall water splitting process. To promote this reaction holistic application, inexpensive, stable and environmentally friendly catalyst should be developed. This study is based on the usage of hydrothermally treated potato peels (HPP) as OER catalyst. To compete with well-performant benchmark catalysts, the unreported method of using UV laser activation (LA) was carried out. This, coupled to the water splitting process set-up optimization (electrodes selection, pH effect, catalyst loading and deposition method) as well as the use of an electrochemical activation (applying 350 consecutive voltammetry cycles) ensured the obtention of Ni foam-HPP-LA electrodes with an astonishing OER performance. Current density values of 10, 50 and 100 mA/cm2 were obtained with low overpotentials of 360, 397 and 416 mV, respectively, and a low Tafel slope of 46.6 mV/dec revealed the quick OER kinetics. FTIR, SEM-EDS and XPS results explain these promising results, highlighting a homogeneous HPP distribution and the fact that laser and electrochemical activations enhanced functional groups presence. The optimal catalyst exhibited a high stability, requiring <1.4 % overpotential increase for keeping 10, 50 and 100 mA/cm2 during 30 h each, obtaining minor physicochemical modifications, which are related to surface oxidation and molecules breakage., Agencia Estatal de Investigación | Ref. RED2022-134552-T, Agencia Estatal de Investigación | Ref. RYC2023-044934-I, Universidade de Vigo/CISUG
RUA. Repositorio Institucional de la Universidad de Alicante
Publication Otros (Other)

Exploring the electro-oxidation of the iodinated contrast iopamidol on different electrode materials for wastewater treatment

  • González Almendros, Sherezade
  • Quintero-Jaime, Andrés Felipe
  • Berenguer Betrián, Raúl
  • Morallon, Emilia
  • Berenguer Betrián, Raúl|||/items/660b8462-63ec-4910-98e0-ac425e6bd7a6
  • González Almendros, Sherezade|||/items/bfde18a9-eaa9-4807-9032-190a15d23ba8
  • Morallon, Emilia|||/items/a15cf511-9365-4c40-afcb-ea29d4418244
Emerging contaminants in water pose a serious threat to the environment and human health, stressing the need of developing efficient treatment processes. In this work, the electrochemical degradation of iopamidol (IOPA), as model iodinated organic pollutant, and the formation of its by-products were investigated on different electrode materials, including commercial anodes (Ti/Pt and Si/BDD) and a synthetized Ti/SnO2-Sb-Pt(13 %) electrode. The electrochemical behaviour and catalytic activity were studied in Na2SO4 by cyclic voltammetry, electrochemical impedance spectroscopy, and galvanostatic experiments in a filter-press reactor. The results show that IOPA can be effectively degraded with all the studied anodes by anodic treatment, involving both the direct and radical dotOHs-mediated oxidation routes. The degradation efficiency achieved after 3 h of electrolysis was found greater than 80 % for all electrodes, being Si/BDD the most efficient anode. By-products analyses with HPLC/MS and ionic chromatography demonstrate the selective dehalogenation of IOPA as the main reaction pathway, giving rise to the formation of non-toxic deiodinated organic compounds. The unselective and highly oxidizing capability of Si/BDD results in rapid and complete mineralization but promotes the accumulation of toxic oxidants and most oxidized inorganic products in the treated residue. By contrast, the lower but more controllable oxidative conditions associated to Pt-containing electrodes enable the conversion of pollutants into valuable compounds and the production of non-toxic aqueous residues. The promoted IOPA interaction and radical dotOHs generation induced by Pt and the SnO2-Sb matrix, respectively, observed for Ti/SnO2-Sb-Pt(13 %), together with its comparatively lower cost, make this anode a good candidate to revalorize or eliminate iodinated organic contrast media.
RUA. Repositorio Institucional de la Universidad de Alicante
Publication Otros (Other)

Altered electrochemistry of poly(3,4-ethylenedioxythiophene) after activation of the inserted cobalt ions

  • Guillén-Bas, Esteban
  • Agrisuelas, Jerónimo
  • García-Jareño, José J.
  • Vicente, Francisco
  • Guillén-Bas, Esteban|||/items/99088a57-13a2-4300-b85d-b09c87183030
Cobalt ions were inserted into poly(3,4-ethylenedioxythiophene) by cyclic voltammetry in a 0.1M Co(NO3)2 aqueous solution (PEDOT(Co)). After activation of the inserted cobalt, the PEDOT(aCo) system was investigated by cyclic voltammetry, digital video electrochemistry, spectroelectrogravimetry, and coupled impedance techniques (ac-electrogravimetry) to elucidate the key role of inserted cobalt ions in the altered electrochemistry of PEDOT. The incorporation of Co2+ involves slow transfer of cations for charge compensation during 𝐶𝑜2+⇄𝐶𝑜3+ conversion inside the PEDOT. This fact explains the enhanced charge storage showed by PEDOT(aCo) compared with pristine PEDOT at similar potentials. Finally, the stability of PEDOT(aCo) was investigated by cyclic voltammetry measuring at the same time current, mass and motional resistance variation during 100 cycles offering high stability at all times.