Skip to main content

METODOLOGIA PARA LA PREDICCION DE EMISIONES DE CO2 Y CONTAMINANTES DE UN MOTOR ALTERNATIVO

TRA2017-89894-R

•
Funding agency name Agencia Estatal de Investigación
Funding agency acronym AEI
Program Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Call Proyectos I+D+i Retos de Investigación
Call year 2017
State Plan 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Beneficiary centre UNIVERSITAT POLITÈCNICA DE VALÈNCIA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 9
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Development and Validation of a Submodel for Thermal Exchanges in the Hydraulic Circuits of a Global Engine Model

  • Broatch, A.|||0000-0001-9991-1039
  • Olmeda, P.|||0000-0002-3161-0165
  • Martín, Jaime|||0000-0002-0496-3176
  • Salvador-Iborra, Josep
[EN] To face the current challenges of the automotive industry, there is a need for computational models capable to simulate the engine behavior under low-temperature and low-pressure conditions. Internal combustion engines are complex and have interconnected systems where many processes take place and influence each other. Thus, a global approach to engine simulation is suitable to study the entire engine performance. The circuits that distribute the hydraulic fluids -liquid fuels, coolants and lubricants- are critical subsystems of the engine. This work presents a 0D model which was developed and set up to make possible the simulation of hydraulic circuits in a global engine model. The model is capable of simulating flow and pressure distributions as well as heat transfer processes in a circuit. After its development, the thermo-hydraulic model was implemented in a physical based engine model called Virtual Engine Model (VEMOD), which takes into account all the relevant relations among subsystems. In the present paper, the thermo-hydraulic model is described and then it is used to simulate oil and coolant circuits of a diesel engine. The objective of the work is to validate the model under steady-state and transient operation, with focus on the thermal evolution of oil and coolant. For validation under steady-state conditions, 22 operating points were measured and simulated, some of them in cold environment. In general, good agreement was obtained between simulation and experiments. Next, the WLTP driving cycle was simulated starting from warmed-up conditions and from ambient temperature. Results were compared with the experiment, showing that modeled trends were close to those experimentally measured. Thermal evolutions of oil and coolant were predicted with mean errors between 0.7 °C and 2.1 °C. In particular, the warm-up phase was satisfactorily modeled., This research has been partially funded by the European Union’s Horizon 2020 Framework Programme for research, technological development and demonstration under grant agreement 723976 (“DiePeR”) and by the Spanish government under the grant agreement TRA2017-89894-R. Josep SalvadorIborra was supported by Universitat Politècnica de València through the contract FPI-S2-2016-1357 of the program PAID01-16. The authors wish to thank Renault SAS, especially P. Mallet and E. Gaïffas, for supporting this research. Jaime Monfort San Segundo is acknowledged for his helpful collaboration in the code implementation
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Development of a Variable Valve Actuation Control to Improve Diesel Oxidation Catalyst Efficiency and Emissions in a Light Duty Diesel Engine

  • Serrano, J.R.|||0000-0003-0692-3917
  • Arnau Martínez, Francisco José|||0000-0003-2902-0630
  • Martín, Jaime|||0000-0002-0496-3176
  • Auñón-García, Ángel
[EN] Growing interest has arisen to adopt Variable Valve Timing (VVT) technology for automotive engines due to the need to fulfill the pollutant emission regulations. Several VVT strategies, such as the exhaust re-opening and the late exhaust closing, can be used to achieve an increment in the after-treatment upstream temperature by increasing the residual gas amount. In this study, a one-dimensional gas dynamics engine model has been used to simulate several VVT strategies and develop a control system to actuate over the valves timing in order to increase diesel oxidation catalyst efficiency and reduce the exhaust pollutant emissions. A transient operating conditions comparison, taking the Worldwide Harmonized Light-Duty Vehicles Test Cycle (WLTC) as a reference, has been done by analyzing fuel economy, HC and CO pollutant emissions levels. The results conclude that the combination of an early exhaust and a late intake valve events leads to a 20% reduction in CO emissions with a fuel penalty of 6% over the low speed stage of the WLTC, during the warm-up of the oxidation catalyst. The same set-up is able to reduce HC emissions down to 16% and NO(x)emission by 13%., This research has been partially funded by the Spanish government under the grant agreement TRA2017-89894-R ("Mecoem"). Angel Aunon was supported through the "Apoyo para la investigacion y Desarrollo (PAID)" grant for doctoral studies (FPI S2 2018 1048) by Universitat Politecnica de Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Analysis of temperature and altitude effects on the Global Energy Balance during WLTC

  • Payri, F.|||0000-0002-3314-4911
  • Martín, Jaime|||0000-0002-0496-3176
  • Arnau Martínez, Francisco José|||0000-0003-2902-0630
  • Artham, Sushma
[EN] In this work, the Global Energy Balance (GEB) of a 1.6 L compression ignition engine is analyzed during WLTC using a combination of experimental measurements and simulations, by means of a Virtual Engine. The energy split considers all the relevant energy terms at two starting temperatures (20 degrees C and 7 degrees C) and two altitudes (0 and 1000 m). It is shown that reducing ambient temperature from 20 degrees C to -7 degrees C decreases brake efficiency by 1% and increases fuel consumption by 4%, mainly because of the higher friction due to the higher oil viscosity, while the effect of increasing altitude 1000 m decreases brake efficiency by 0.8% and increases fuel consumption by 2.5% in the WLTC mainly due to the change in pumping. In addition, GEB shows that ambient temperature is affecting exhaust enthalpy by 4.5%, heat rejection to coolant by 2%, and heat accumulated in the block by 2.5%, while altitude does not show any remarkable variations other than pumping and break power., The author(s) disclosed receipt of the following financial support for the research, authorship, and/or publication of this article: This research has been partially funded by the European Union's Horizon 2020 Framework Programme for research, technological development and demonstration under grant agreement 723976 ("DiePeR'') and by the Spanish government under the grant agreement TRA2017-89894-R ("MECOEM'') and Sushma Artham was supported by FPI grant with reference PRE2018-084411. The authors wish to thank Renault SAS, especially P. Mallet and E. Gaiffas, for supporting this research.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Diesel engine optimization and exhaust thermal management by means of variable valve train strategies

  • Arnau Martínez, Francisco José|||0000-0003-2902-0630
  • Martín, Jaime|||0000-0002-0496-3176
  • Pla Moreno, Benjamín|||0000-0001-9238-2939
  • Auñón-García, Ángel
[EN] Due to the need to achieve a fast warm-up of the after-treatment system in order to fulfill the pollutant emission regulations, a growing interest has arisen to adopt variable valve timing technology for automotive engines. Several variable valve timing strategies can be used to achieve an increment in the after-treatment upstream temperature by increasing the residual gas amount. In this study, a one-dimensional gas dynamics engine model has been used to carry out a simulation study comparing several exhaust variable valve actuation strategies. A steady-state analysis has been done in order to evaluate the potential of the different strategies at different operating points. Finally, the effect on the after-treatment warm-up, fuel economy and pollutant emission levels was evaluated over the worldwide harmonized light vehicles test cycle. As a conclusion, the combination of an advanced exhaust (early exhaust valve opening and early exhaust valve closing) and a delayed intake (late intake valve opening and late intake valve closing) presented the best trade-off between exhaust temperature increment and fuel consumption, which achieved a mean temperature increment during low-speed phase of the worldwide harmonized light vehicles test cycle of 27¿°C with a fuel penalty of 6%. The exhaust valve re-opening technique offers a worse trade-off. However, the exhaust valve re-opening leads to lower nitrogen oxide (29% less) and carbon monoxide (11% less) pollutant emissions., The author(s) disclosed receipt of the following financial support for the research, authorship, and/or publication of this article: This research has been partially funded by the European Union's Horizon 2020 Framework Programme for research, technological development and demonstration under grant agreement 723976 ("DiePeR") and by the Spanish government under the grant agreement TRA2017-89894-R. The authors want to acknowledge the "Apoyo para la investigacion y Desarrollo (PAID)," grant for doctoral studies (FPI S2 2018 1048), of Universitat Politecnica de Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Development of an Integrated Virtual Engine Model to Simulate New Standard Testing Cycles

  • Martín, Jaime|||0000-0002-0496-3176
  • Arnau Martínez, Francisco José|||0000-0003-2902-0630
  • Piqueras, P.|||0000-0002-3767-0839
  • Auñón-García, Ángel
[EN] The combination of more strict regulation for pollutant and CO2 emissions and the new testing cycles, covering a wider range of transient conditions, makes very interesting the development of predictive tools for engine design and pre-calibration. This paper describes a new integrated Virtual Engine Model (VEMOD) that has been developed as a standalone tool to simulate new standard testing cycles. The VEMOD is based on a wave-action model that carries out the thermo-and fluid dynamics calculation of the gas in each part of the engine. In the model, the engine is represented by means of 1D ducts, while the volumes, such as cylinders and reservoirs, are considered as 0D elements. Different sub-models are included in the VEMOD to take into account all the relevant phenomena. Thus, the combustion process is calculated by the Apparent Combustion Time (ACT) 1D model, responsible for the prediction of the rate of heat release and NOx formation. Experimental correlations are used to determine the rest of pollutants. In order to predict tailpipe pollutant emissions to the ambient, different sub-models have been developed to reproduce the behavior of the aftertreatment devices (DOC and DPF) placed in the exhaust system. Dedicated friction and auxiliaries sub-models allow obtaining the brake power. The turbocharger consists of 0D compressor and turbine sub-models capable of extrapolating the available maps of both devices. The VEMOD includes coolant and lubricant circuits linked, on the one hand, with the engine block and the turbocharger through heat transfer lumped models; and on the other hand with the engine heat exchangers. A control system emulating the ECU along with vehicle and driver sub-models allow completing the engine simulation. The Virtual Engine Model has been validated with experimental tests in a 1.6 L Diesel engine using steady and transient tests in both hot and cold conditions. Engine torque was predicted with a mean error of 3 Nm and an error below 14 Nm for 90 % of the cycle duration. CO2 presented a mean error of 0.04 g/s, while during 80 % of the cycle, error was below 0.44 g/s., This research has been partially funded by the European Union’s Horizon 2020 Framework Programme for research, technological development and demonstration under grant agreement 723976 (“DiePeR”) and by the Spanish government under the grant agreement TRA2017-89894-R. The authors wish to thank Renault SAS, especially P. Mallet and E. Gaïffas, for supporting this research.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Analysis of the energy balance during World harmonized Light vehicles Test Cycle in warmed and cold conditions using a Virtual Engine

  • Olmeda, P.|||0000-0002-3161-0165
  • Martín, Jaime|||0000-0002-0496-3176
  • Arnau Martínez, Francisco José|||0000-0003-2902-0630
  • Artham, Sushma
[EN] In recent years, the interests on transient operation and real driving emissions have increased because of the global concern about environmental pollution that has led to new emissions regulation and new standard testing cycles. In this framework, it is mandatory to focus the engines research on the transient operation, where a Virtual Engine has been used to perform the global energy balance of a 1.6-L diesel engine during a World harmonized Light vehicles Test Cycle. Thus, the energy repartition of the chemical energy has been described with warmed engine and cold start conditions, analyzing in detail the mechanisms affecting the engine consumption. The first analysis focuses on the ¿delay¿ effect affecting the instantaneous energy balance due to the time lag between the in-cylinder processes and pipes: as a main conclusion, it is obtained that it leads to an apparent unbalance than can reach more than 10% of the cumulated fuel energy at the beginning of the cycle, becoming later negligible. Energy split analysis in cold starting World harmonized Light vehicles Test Cycle shows that in this condition the energy accumulation in the block is a key term at the beginning (about 50%) that diminishes its weight until about 10% at the end of the cycle. In warmed conditions, energy accumulation is negligible, but the heat transfer to coolant and oil are higher than in cold starting conditions (21% vs 28%). The lower values of the mean brake efficiency at the beginning of the World harmonized Light vehicles Test Cycle (only about 20%) is affected, especially in cold starting, by the higher mechanical losses due to the higher oil viscosity and the heat rejection from the gases. The friction plays an important role only during the first half of the cycle, with a percentage of about 65% of the total mechanical losses and 10% of the total fuel energy at the end of the World harmonized Light vehicles Test Cycle. However, at the end of the cycle, it does not affect dramatically the mean brake efficiency which is about 31% both in cold starting and warmed World harmonized Light vehicles Test Cycle., The author(s) disclosed receipt of the following financial support for the research, authorship and/or publication of this article: This research has been partially funded by the European Union's Horizon 2020 Framework Programme for research, technological development and demonstration under grant agreement 723976 ("DiePeR'') and by the Spanish government under the grant agreement TRA2017-89894-R. The authors wish to thank Renault SAS, especially P. Mallet and E. Gaiffas, for supporting this research.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Assessing the optimum combustion under constrained conditions

  • Olmeda, P.|||0000-0002-3161-0165
  • Martín, Jaime|||0000-0002-0496-3176
  • Novella Rosa, Ricardo|||0000-0002-5123-6924
  • Blanco-Cavero, Diego
[EN] This work studies the optimum heat release law of a direct injection diesel engine under constrained conditions. For this purpose, a zero-dimensional predictive model of a diesel engine is coupled to an optimization tool used to shape the heat release law in order to optimize some outputs (maximize gross indicated efficiency and minimize NOx emissions) while keeping several restrictions (mechanical limits such as maximum peak pressure and maximum pressure rise rate). In a first step, this methodology is applied under different heat transfer scenarios without restrictions to evaluate the possible gain obtained through the thermal isolation of the combustion chamber. Results derived from this study show that heat transfer has a negative effect on gross indicated efficiency ranging from -4% of the fuel energy (m(f)H(v)), at high engine speed and load, up to -8% m(f)H(v), at low engine speed and load. In a second step, different mechanical limits are applied resulting in a gross indicated efficiency worsening from -1.4% m(f)H(v) up to -2.8% m(f)H(v) compared to the previous step when nominal constraints are applied. In these conditions, a temperature swing coating that covers the piston top and cylinder head is considered obtaining a maximum gross indicated efficiency improvement of +0.5% m(f)H(v) at low load and engine speed. Finally, NOx emissions are also included in the optimization obtaining the expected tradeoff between gross indicated efficiency and NOx. Under this optimization, cutting down the experimental emissions by 50% supposes a gross indicated efficiency penalty up to -8% m(f)H(v) when compared to the optimum combustion under nominal limits, while maintaining the experimental gross indicated efficiency allows to reduce the experimental emissions 30% at high load and 65% at low load and engine speed., This work was partially funded by GM Global R&D and the Government of Spain through Project TRA2017-89894-R. In addition, the authors acknowledge that some equipment used in this work has been partially supported by FEDER project funds (FEDER-ICTS-2012-06), framed in the operational programme of unique scientific and technical infrastructure of the Ministry of Science and Innovation of Spain. Diego Blanco-Cavero is partially supported through contract FPI-S2-2016-1356 of the Programa de Apoyo para la Investigacion y Desarrollo (PAID) of Universitat Politcenica de Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Effect of the exhaust thermal insulation on the engine efficiency and the exhaust temperature under transient conditions

  • Arnau Martínez, Francisco José|||0000-0003-2902-0630
  • Martín, Jaime|||0000-0002-0496-3176
  • Piqueras, P.|||0000-0002-3767-0839
  • Auñón-García, Ángel
[EN] As well as new advances in the after-treatment systems are required to achieve the new pollutant emission requirements, new designs of the exhaust line can be considered in order to increase the engine efficiency and the after-treatment effectiveness. In the present work, a one-dimensional gas dynamic model has been used to carry out a simulation study comparing several exhaust insulation solutions. This solutions include the insulation of the exhaust ports, the exhaust manifold, the internal surface of the turbine volute, the turbine external housing, as well as different combinations of these solutions. A transient analysis has been done in order to evaluate the increment in the exhaust gases temperature, fuel economy and pollutant emission levels over the WLTC (Worldwide harmonized Light vehicles Test Cycle) at three different temperature conditions. As a conclusion, a 12% increment in the turbine outlet gas enthalpy can be achieved by insulating both the exhausts ports and the exhaust manifold. Moreover, more than 30% less pollutant emissions are released to the environment with this setup., The author(s) disclosed receipt of the following financial support for the research, authorship, and/or publication of this article: This research has been partially funded by the European Union's Horizon 2020 Framework Programme for research, technological development and demonstration under grant agreement 723976 ("DiePeR'') and by the Spanish government under the grant agreement TRA2017-89894-R ("Mecoem''). Angel Aunon was supported through the "Apoyo para la investigacion y Desarrollo (PAID)'' grant for doctoral studies (FPI S2 2018 1048) by Universitat Politecnica de Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

One-Dimensional Modeling of Mechanical and Friction Losses Distribution in a Four-Stroke Internal Combustion Engine

  • Tormos, B.|||0000-0002-8852-3783
  • Martín, Jaime|||0000-0002-0496-3176
  • Blanco-Cavero, Diego
  • Jiménez-Reyes, Antonio José
[EN] As the road transport accounts between 15%-18% of worldwide CO2 emissions, the automotive sector has a deep commitment to mitigate global warming. Consequently, stricter regulations have been adopted by the European Union and worldwide to reduce that big impact. Approximately, 10% of the energy generated by fuel combustion in the engine is destined to the auxiliaries components activation and the movement of mechanical elements with relative motion between themselves. A reduction on that figure or alternatively a mechanical efficiency improvement can be directly translated on target alignment. The aim of this work is developing a model to predict the mechanical and friction losses and its distribution in a four-stroke direct injection-diesel engine and simulating different strategies, which increment the engine efficiency. A 1D model has been developed and fitted in GT-SUITE based on the experimental results of a 1.6-L diesel engine. Additionally, a description of the tribological performance has been realized in different parts of the engine where friction is present. Finally, the engine friction maps have been broken down in order to quantify the friction losses produced in the piston ring assembly, crankshaft bearings, and valvetrain