Skip to main content

METODOLOGIA PARA LA PREDICCION DE EMISIONES DE CO2 Y CONTAMINANTES DE UN MOTOR ALTERNATIVO

TRA2017-89894-R

•
Funding agency name Agencia Estatal de Investigación
Funding agency acronym AEI
Program Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Call Proyectos I+D+i Retos de Investigación
Call year 2017
State Plan 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Beneficiary centre UNIVERSITAT POLITÈCNICA DE VALÈNCIA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 11
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Development and Validation of a Submodel for Thermal Exchanges in the Hydraulic Circuits of a Global Engine Model

  • Broatch, A.|||0000-0001-9991-1039
  • Olmeda, P.|||0000-0002-3161-0165
  • Martín, Jaime|||0000-0002-0496-3176
  • Salvador-Iborra, Josep
[EN] To face the current challenges of the automotive industry, there is a need for computational models capable to simulate the engine behavior under low-temperature and low-pressure conditions. Internal combustion engines are complex and have interconnected systems where many processes take place and influence each other. Thus, a global approach to engine simulation is suitable to study the entire engine performance. The circuits that distribute the hydraulic fluids -liquid fuels, coolants and lubricants- are critical subsystems of the engine. This work presents a 0D model which was developed and set up to make possible the simulation of hydraulic circuits in a global engine model. The model is capable of simulating flow and pressure distributions as well as heat transfer processes in a circuit. After its development, the thermo-hydraulic model was implemented in a physical based engine model called Virtual Engine Model (VEMOD), which takes into account all the relevant relations among subsystems. In the present paper, the thermo-hydraulic model is described and then it is used to simulate oil and coolant circuits of a diesel engine. The objective of the work is to validate the model under steady-state and transient operation, with focus on the thermal evolution of oil and coolant. For validation under steady-state conditions, 22 operating points were measured and simulated, some of them in cold environment. In general, good agreement was obtained between simulation and experiments. Next, the WLTP driving cycle was simulated starting from warmed-up conditions and from ambient temperature. Results were compared with the experiment, showing that modeled trends were close to those experimentally measured. Thermal evolutions of oil and coolant were predicted with mean errors between 0.7 °C and 2.1 °C. In particular, the warm-up phase was satisfactorily modeled., This research has been partially funded by the European Union’s Horizon 2020 Framework Programme for research, technological development and demonstration under grant agreement 723976 (“DiePeR”) and by the Spanish government under the grant agreement TRA2017-89894-R. Josep SalvadorIborra was supported by Universitat Politècnica de València through the contract FPI-S2-2016-1357 of the program PAID01-16. The authors wish to thank Renault SAS, especially P. Mallet and E. Gaïffas, for supporting this research. Jaime Monfort San Segundo is acknowledged for his helpful collaboration in the code implementation
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Development of a Variable Valve Actuation Control to Improve Diesel Oxidation Catalyst Efficiency and Emissions in a Light Duty Diesel Engine

  • Serrano, J.R.|||0000-0003-0692-3917
  • Arnau Martínez, Francisco José|||0000-0003-2902-0630
  • Martín, Jaime|||0000-0002-0496-3176
  • Auñón-García, Ángel
[EN] Growing interest has arisen to adopt Variable Valve Timing (VVT) technology for automotive engines due to the need to fulfill the pollutant emission regulations. Several VVT strategies, such as the exhaust re-opening and the late exhaust closing, can be used to achieve an increment in the after-treatment upstream temperature by increasing the residual gas amount. In this study, a one-dimensional gas dynamics engine model has been used to simulate several VVT strategies and develop a control system to actuate over the valves timing in order to increase diesel oxidation catalyst efficiency and reduce the exhaust pollutant emissions. A transient operating conditions comparison, taking the Worldwide Harmonized Light-Duty Vehicles Test Cycle (WLTC) as a reference, has been done by analyzing fuel economy, HC and CO pollutant emissions levels. The results conclude that the combination of an early exhaust and a late intake valve events leads to a 20% reduction in CO emissions with a fuel penalty of 6% over the low speed stage of the WLTC, during the warm-up of the oxidation catalyst. The same set-up is able to reduce HC emissions down to 16% and NO(x)emission by 13%., This research has been partially funded by the Spanish government under the grant agreement TRA2017-89894-R ("Mecoem"). Angel Aunon was supported through the "Apoyo para la investigacion y Desarrollo (PAID)" grant for doctoral studies (FPI S2 2018 1048) by Universitat Politecnica de Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Analysis of temperature and altitude effects on the Global Energy Balance during WLTC

  • Payri, F.|||0000-0002-3314-4911
  • Martín, Jaime|||0000-0002-0496-3176
  • Arnau Martínez, Francisco José|||0000-0003-2902-0630
  • Artham, Sushma
[EN] In this work, the Global Energy Balance (GEB) of a 1.6 L compression ignition engine is analyzed during WLTC using a combination of experimental measurements and simulations, by means of a Virtual Engine. The energy split considers all the relevant energy terms at two starting temperatures (20 degrees C and 7 degrees C) and two altitudes (0 and 1000 m). It is shown that reducing ambient temperature from 20 degrees C to -7 degrees C decreases brake efficiency by 1% and increases fuel consumption by 4%, mainly because of the higher friction due to the higher oil viscosity, while the effect of increasing altitude 1000 m decreases brake efficiency by 0.8% and increases fuel consumption by 2.5% in the WLTC mainly due to the change in pumping. In addition, GEB shows that ambient temperature is affecting exhaust enthalpy by 4.5%, heat rejection to coolant by 2%, and heat accumulated in the block by 2.5%, while altitude does not show any remarkable variations other than pumping and break power., The author(s) disclosed receipt of the following financial support for the research, authorship, and/or publication of this article: This research has been partially funded by the European Union's Horizon 2020 Framework Programme for research, technological development and demonstration under grant agreement 723976 ("DiePeR'') and by the Spanish government under the grant agreement TRA2017-89894-R ("MECOEM'') and Sushma Artham was supported by FPI grant with reference PRE2018-084411. The authors wish to thank Renault SAS, especially P. Mallet and E. Gaiffas, for supporting this research.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Tesis doctoral (DoctoralThesis)

Contribution to the simulation of new standard testing cycles by means of a 0D/1D tool

  • Artham, Sushma
[ES] El objetivo principal de esta tesis es establecer una metodología para predecir el consumo de combustible y las emisiones de un motor de encendido por compresión en condiciones transitorias. Además, su objetivo es explorar cómo las diferentes configuraciones del motor y los factores ambientales impactan el comportamiento del motor utilizando un enfoque de modelado 0D/1D. Además, el estudio pretende extender esta metodología a los motores duales, analizando específicamente las características de combustión de metano-diésel e hidrógeno-diésel. Para lograrlo, la herramienta de modelado 0D/1D se ajustó y validó meticulosamente utilizando un motor diésel de cuatro cilindros. Esta alineación entre la simulación y datos experimentales se centró especialmente en factores cruciales como la presión, la liberación de calor, las temperaturas en los fluidos del motor y el par. Se realizó un análisis exhaustivo del Balance Energético Global (GEB) utilizando VEMOD (Virtual Engine Model). Este análisis proporcionó información detallada sobre el consumo del motor y su reacción en diversas condiciones de funcionamiento, particularmente durante el Ciclo de ensayo mundial armonizado de vehículos ligeros (WLTC). La comparación de términos energéticos entre diferentes condiciones ambientales y de motor destacó aspectos como la fricción, la transferencia de calor y la acumulación de calor. Además, el análisis GEB permitió explorar cómo se distribuía la energía con diferentes temperaturas y altitudes ambientes. El estudio también evaluó las emisiones de NOx, revelando patrones influenciados por factores como las tasas de recirculación de gases de escape (EGR) y la temperatura de admisión. En el ámbito de los motores de combustible dual, se elaboró y validó un modelo de combustión utilizando la herramienta de simulación 0D/1D. La atención inicial se centró en la combustión de metano-Diesel, validada con datos experimentales. Posteriormente, el alcance de este modelo se amplió para simular la combustión de hidrógeno-Diesel. Esta tesis ha introducido con éxito una metodología que utiliza VEMOD para predecir el consumo y las emisiones del motor en distintos escenarios. El análisis exhaustivo arrojó luz sobre cómo funcionan los mecanismos de distribución de energía y cómo diferentes factores influyen en el comportamiento del motor. La aplicación de esta metodología a motores de encendido por compresión ha demostrado su versatilidad y capacidad de predicción, lo que la convierte en una herramienta valiosa para investigar escenarios futuros, también con combustiones duales., [CA] L'objectiu principal d'aquesta tesi és establir una metodologia per predir el consum de combustible i les emissions d'un motor d'encesa per compressió en condicions transitòries. A més, pretén explorar com diferents configuracions de motors i factors ambientals afecten el comportament del motor mitjançant un enfocament de modelització 0D/1D. A més, l'estudi s'esforça a estendre aquesta metodologia als motors de doble combustible (duals), analitzant específicament les característiques de combustió de metà-dièsel i hidrogendièsel. Per aconseguir-ho, l'eina de modelització 0D/1D es va ajustar minuciosament i es va validar mitjançant un motor dièsel de quatre cilindres. Aquesta alineació entre dades de simulació i món real es va centrar especialment en factors crucials com la pressió, l'alliberament de calor, les temperatures dels fluids del motor i el parell. Es va realitzar una anàlisi completa del Balanç Global d'Energia (GEB) mitjançant VEMOD (Virtual Engine Model). Aquesta anàlisi va proporcionar una visió profunda sobre el consum del motor i la seua reacció en diverses condicions de funcionament, especialment durant el Cicle mundial d'assaig de vehicles lleugers harmonitzats (WLTC). La comparació de termes energètics entre diferents condicions ambientals i del motor van posar de manifest aspectes com la fricció, la transferència de calor i l'acumulació de calor. A més, l'anàlisi GEB va explorar com es va distribuir l'energia amb diferents temperatures i altituds ambientals. L'estudi també va valorar les emissions de NOx, revelant patrons influenciats per factors com la recirculació de gasos d'escapament (EGR) i la temperatura d'admissió. En l'àmbit dels motors duals, es va elaborar i validar un model de combustió mitjançant l'eina de simulació 0D/1D. El focus inicial es va centrar en la combustió metà-Diesel, validada amb dades experimentals. Posteriorment, l'abast d'aquest model es va ampliar per simular la combustió hidrogen-Diesel. Aquesta tesi ha introduït amb èxit una metodologia que utilitza VEMOD per predir el consum i les emissions del motor en diferents escenaris. L'anàlisi completa va donar llum a com funcionen els mecanismes de distribució d'energia i com diferents factors influeixen en el comportament del motor. L'aplicació d'aquesta metodologia als motors d'encesa per compressió va demostrar la seva versatilitat i capacitats de predicció, convertint-la en una valuosa eina per investigar els futurs escenaris, fins i tot amb combustions duals., [EN] The main aim of this thesis is to establish a methodology for predicting fuel consumption and emissions of a compression ignition engine in transient conditions. Additionally, it aims to explore how different engine setups and environmental factors impact the engine's performance using a 0D/1D modelling approach. Moreover, the study strives to extend this methodology to dual fuel engines, specifically analysing methane-Diesel and hydrogen- Diesel combustion characteristics. The 0D/1D modelling tool was meticulously fine-tuned and validated using a four-cylinder Diesel engine to achieve this. This alignment between simulation and experimental data focused on crucial factors such as pressure, heat release, engine fluid temperatures and torque. A comprehensive Global Energy Balance (GEB) analysis was conducted using VEMOD (Virtual Engine Model). This analysis provided insights into the engine consumption and performance under diverse operating conditions, particularly during the Worldwide Harmonized Light Vehicles Test Cycle (WLTC). The comparison of energy terms across different engine and boundary conditions highlighted aspects such as friction, heat rejection, and heat accumulation. Additionally, the GEB analysis allowed exploration of how energy was split across varying ambient temperatures and altitudes. The study also assessed NOx emissions, revealing patterns influenced by factors such as Exhaust Gas Recirculation (EGR) rates and intake temperature. A combustion model was developed and validated using the 0D/1D simulation tool in the scope of dual fuel engines. The initial focus was on methane-Diesel combustion, validated against experimental data. Subsequently, this model scope was expanded to simulate hydrogen-Diesel combustion. This thesis has successfully introduced a methodology based on VEMOD to predict engine consumption and emissions across varying scenarios. The comprehensive analysis illuminated how energy distribution mechanisms operate and how factors influence engine performances. The application of this methodology to compression ignition engines demonstrated its versatility and prediction capabilities, making it a valuable tool for investigating future combustion scenarios, including dual fuel operation., This research has been partially funded by the European Union’s Horizon 2020 Framework Programme for research, technological development and demonstration under grant agreement 723976 (“DiePeR”) and by the Spanish government under the grant agreement TRA2017-89894-R (”MECOEM”) and I was supported by FPI grant with reference PRE2018-084411.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Diesel engine optimization and exhaust thermal management by means of variable valve train strategies

  • Arnau Martínez, Francisco José|||0000-0003-2902-0630
  • Martín, Jaime|||0000-0002-0496-3176
  • Pla Moreno, Benjamín|||0000-0001-9238-2939
  • Auñón-García, Ángel
[EN] Due to the need to achieve a fast warm-up of the after-treatment system in order to fulfill the pollutant emission regulations, a growing interest has arisen to adopt variable valve timing technology for automotive engines. Several variable valve timing strategies can be used to achieve an increment in the after-treatment upstream temperature by increasing the residual gas amount. In this study, a one-dimensional gas dynamics engine model has been used to carry out a simulation study comparing several exhaust variable valve actuation strategies. A steady-state analysis has been done in order to evaluate the potential of the different strategies at different operating points. Finally, the effect on the after-treatment warm-up, fuel economy and pollutant emission levels was evaluated over the worldwide harmonized light vehicles test cycle. As a conclusion, the combination of an advanced exhaust (early exhaust valve opening and early exhaust valve closing) and a delayed intake (late intake valve opening and late intake valve closing) presented the best trade-off between exhaust temperature increment and fuel consumption, which achieved a mean temperature increment during low-speed phase of the worldwide harmonized light vehicles test cycle of 27¿°C with a fuel penalty of 6%. The exhaust valve re-opening technique offers a worse trade-off. However, the exhaust valve re-opening leads to lower nitrogen oxide (29% less) and carbon monoxide (11% less) pollutant emissions., The author(s) disclosed receipt of the following financial support for the research, authorship, and/or publication of this article: This research has been partially funded by the European Union's Horizon 2020 Framework Programme for research, technological development and demonstration under grant agreement 723976 ("DiePeR") and by the Spanish government under the grant agreement TRA2017-89894-R. The authors want to acknowledge the "Apoyo para la investigacion y Desarrollo (PAID)," grant for doctoral studies (FPI S2 2018 1048), of Universitat Politecnica de Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Development of an Integrated Virtual Engine Model to Simulate New Standard Testing Cycles

  • Martín, Jaime|||0000-0002-0496-3176
  • Arnau Martínez, Francisco José|||0000-0003-2902-0630
  • Piqueras, P.|||0000-0002-3767-0839
  • Auñón-García, Ángel
[EN] The combination of more strict regulation for pollutant and CO2 emissions and the new testing cycles, covering a wider range of transient conditions, makes very interesting the development of predictive tools for engine design and pre-calibration. This paper describes a new integrated Virtual Engine Model (VEMOD) that has been developed as a standalone tool to simulate new standard testing cycles. The VEMOD is based on a wave-action model that carries out the thermo-and fluid dynamics calculation of the gas in each part of the engine. In the model, the engine is represented by means of 1D ducts, while the volumes, such as cylinders and reservoirs, are considered as 0D elements. Different sub-models are included in the VEMOD to take into account all the relevant phenomena. Thus, the combustion process is calculated by the Apparent Combustion Time (ACT) 1D model, responsible for the prediction of the rate of heat release and NOx formation. Experimental correlations are used to determine the rest of pollutants. In order to predict tailpipe pollutant emissions to the ambient, different sub-models have been developed to reproduce the behavior of the aftertreatment devices (DOC and DPF) placed in the exhaust system. Dedicated friction and auxiliaries sub-models allow obtaining the brake power. The turbocharger consists of 0D compressor and turbine sub-models capable of extrapolating the available maps of both devices. The VEMOD includes coolant and lubricant circuits linked, on the one hand, with the engine block and the turbocharger through heat transfer lumped models; and on the other hand with the engine heat exchangers. A control system emulating the ECU along with vehicle and driver sub-models allow completing the engine simulation. The Virtual Engine Model has been validated with experimental tests in a 1.6 L Diesel engine using steady and transient tests in both hot and cold conditions. Engine torque was predicted with a mean error of 3 Nm and an error below 14 Nm for 90 % of the cycle duration. CO2 presented a mean error of 0.04 g/s, while during 80 % of the cycle, error was below 0.44 g/s., This research has been partially funded by the European Union’s Horizon 2020 Framework Programme for research, technological development and demonstration under grant agreement 723976 (“DiePeR”) and by the Spanish government under the grant agreement TRA2017-89894-R. The authors wish to thank Renault SAS, especially P. Mallet and E. Gaïffas, for supporting this research.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Analysis of the energy balance during World harmonized Light vehicles Test Cycle in warmed and cold conditions using a Virtual Engine

  • Olmeda, P.|||0000-0002-3161-0165
  • Martín, Jaime|||0000-0002-0496-3176
  • Arnau Martínez, Francisco José|||0000-0003-2902-0630
  • Artham, Sushma
[EN] In recent years, the interests on transient operation and real driving emissions have increased because of the global concern about environmental pollution that has led to new emissions regulation and new standard testing cycles. In this framework, it is mandatory to focus the engines research on the transient operation, where a Virtual Engine has been used to perform the global energy balance of a 1.6-L diesel engine during a World harmonized Light vehicles Test Cycle. Thus, the energy repartition of the chemical energy has been described with warmed engine and cold start conditions, analyzing in detail the mechanisms affecting the engine consumption. The first analysis focuses on the ¿delay¿ effect affecting the instantaneous energy balance due to the time lag between the in-cylinder processes and pipes: as a main conclusion, it is obtained that it leads to an apparent unbalance than can reach more than 10% of the cumulated fuel energy at the beginning of the cycle, becoming later negligible. Energy split analysis in cold starting World harmonized Light vehicles Test Cycle shows that in this condition the energy accumulation in the block is a key term at the beginning (about 50%) that diminishes its weight until about 10% at the end of the cycle. In warmed conditions, energy accumulation is negligible, but the heat transfer to coolant and oil are higher than in cold starting conditions (21% vs 28%). The lower values of the mean brake efficiency at the beginning of the World harmonized Light vehicles Test Cycle (only about 20%) is affected, especially in cold starting, by the higher mechanical losses due to the higher oil viscosity and the heat rejection from the gases. The friction plays an important role only during the first half of the cycle, with a percentage of about 65% of the total mechanical losses and 10% of the total fuel energy at the end of the World harmonized Light vehicles Test Cycle. However, at the end of the cycle, it does not affect dramatically the mean brake efficiency which is about 31% both in cold starting and warmed World harmonized Light vehicles Test Cycle., The author(s) disclosed receipt of the following financial support for the research, authorship and/or publication of this article: This research has been partially funded by the European Union's Horizon 2020 Framework Programme for research, technological development and demonstration under grant agreement 723976 ("DiePeR'') and by the Spanish government under the grant agreement TRA2017-89894-R. The authors wish to thank Renault SAS, especially P. Mallet and E. Gaiffas, for supporting this research.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Tesis de maestría (MasterThesis)

Modelado 1D de las pérdidas mecánicas en un MCIA y su distribución durante un ciclo real de conducción

  • Jiménez Reyes, Antonio José
[ES] En la última década, el incremento de las emisiones de gases de efecto invernadero a la atmósfera ha servido de impulso a investigadores y fabricantes para el desarrollo de motores más eficientes, con menos consumo de combustible y, por lo tanto, con una menor emisión de CO2 a la atmósfera. Con este propósito se propone la siguiente estrategia: desarrollar un modelo 1D de pérdidas mecánicas para profundizar en el fenómeno de la fricción en motores de combustión interna y, así, ser capaz de reducir las pérdidas mecánicas por fricción y aumentar el rendimiento del motor. Las pérdidas mecánicas en un motor de combustión interna representan, aproximadamente, el 18% de la energía introducida en el motor. Estas pérdidas mecánicas representan el consumo energético destinado a accionar los elementos auxiliares tales como: bomba de combustible, bomba de aceite y bomba de refrigerante entre otros, necesarios para el funcionamiento del motor; a vencer las pérdidas por bombeo producidas durante el proceso de renovación de la carga y finalmente, a vencer las pérdidas por fricción existente en los elementos con movimientos relativos entre sí. Actualmente, diferentes estudios han demostrado que las pérdidas mecánicas pueden ser disminuidas mediante el uso de aceites de baja viscosidad, básicamente por la reducción de la fricción viscosa en aquellos elementos dónde la película de aceite tiene un mayor espesor, esto es, trabaja en régimen de lubricación hidrodinámica, véase los cojinetes principales. Sin embargo, el hecho de disminuir la viscosidad redunda en la disminución de la película de aceite entre los elementos, lo que puede provocar un aumento, a su vez, de la fricción por contacto directo (régimen límite). Acorde a lo descrito anteriormente, una manera de disminuir el coste experimental asociado a la medición del comportamiento de distintos aceites lubricantes y diferentes elementos mecánicos con diferentes acabados superficiales en el motor es implementar un modelo que prediga el comportamiento de las pérdidas mecánicas por fricción en el mismo. Para ello, el objetivo de este trabajo es desarrollar un modelo 1D aplicable a cualquier MCIA con sus correspondientes parámetros geométricos, datos específicos de sus elementos auxiliares, acabados superficiales y parámetros termodinámicos de los puntos de operación para obtener los datos de las pérdidas mecánicas por fricción., [CA] En l'última dècada, l'increment de les emissions de gasos d'efecte hivernacle a l'atmosfera ha servit d'impuls a investigadors i fabricants per al desenvolupament de motors més eficients, amb menys consum de combustible i, per tant, amb una menor emissió de CO2 a l'atmosfera. Amb aquest propòsit es proposa la següent estratègia: desenvolupar un model 1D de pèrdues mecàniques per aprofundir en el fenomen de la fricció en motors de combustió interna i, així, ser capaç de reduir les pèrdues mecàniques per fricció i augmentar el rendiment del motor. Les pèrdues mecàniques en un motor de combustió interna representen, aproximadament, el 18% de l'energia introduïda en el motor. Aquestes pèrdues mecàniques representen el consum energètic destinat a accionar els elements auxiliars com ara: bomba de combustible, bomba d'oli i bomba de refrigerant entre d'altres, necessaris per al funcionament del motor; a vèncer les pèrdues per bombeig produïdes durant el procés de renovació de la càrrega i finalment, a vèncer les pèrdues per fricció existent en els elements amb moviments relatius entre ells. Actualment, diferents estudis han demostrat que les pèrdues mecàniques poden ser disminuïdes mitjançant l'ús d'olis de baixa viscositat, bàsicament per la reducció de la fricció viscosa en aquells elements on la pel·lícula d'oli té un major gruix, és a dir, treballa en règim de lubricació hidrodinàmica, com podria ser als coixinets principals. No obstant això, el fet de disminuir la viscositat redunda en la disminució de la pel·lícula d'oli entre els elements, la qual cosa pot provocar un augment, al seu torn, de la fricció per contacte directe (règim límit). Concorde al descrit anteriorment, una manera de disminuir el cost experimental associat al mesurament del comportament de diferents olis lubrificants i diferents elements mecànics amb diferents acabats superficials en el motor és implementar un model que prediga el comportament de les pèrdues mecàniques per fricció en aquest. Per a això, l'objectiu d'aquest treball és desenvolupar un model 1D aplicable a qualsevol **MCIA amb els seus corresponents paràmetres geomètrics, dades específiques dels seus elements auxiliars, acabats superficials i paràmetres termodinàmics dels punts d'operació per a obtenir les dades de les pèrdues mecàniques per fricció., [EN] In the last decade, the increase in GHG emissions into the atmosphere has served as a boost for researchers and engine manufacturers to develop more efficient engines, with less fuel consumption and, therefore, with lower emissions of CO2 into the atmosphere. For this purpose, the following strategy is proposed: develop a 1D model of mechanical losses to look deeper into the friction phenomenon in internal combustion engines and, thus, be able to reduce mechanical losses due to friction and increase engine performance. The mechanical losses in an internal combustion engine represent approximately 18% of the energy introduced into the engine. These mechanical losses represent the energy consumption used to drive the auxiliary elements such as: fuel pump, oil pump and coolant pump, among others, necessary for the operation of the engine; to overcome the pumping losses produced during the air intake-exhaust process and finally, to overcome the friction losses existing in the elements with relative motion between them. Currently, different studies have shown that mechanical losses can be decreased through the use of low-viscosity oils, basically due to the reduction of viscous friction in those elements where the oil film has higher thickness that is, working under hydrodynamic lubrication. However, the fact of reducing the viscosity can lead to a reduction of the oil film between the lubricated elements, which in turn can cause an increase in the friction force by direct contact (boundary lubrication regime). According to this, one way of reducing the experimental cost associated with measuring the performance of different lubricating oils and different mechanical elements with different surface textures in the engine is to implement a model that predicts the performance of friction mechanical losses. Attending that, the objective of this work is to develop a 1D model applicable to an ICE with its corresponding geometric parameters, specific data about its auxiliary elements, surface textures and thermodynamic parameters of the operating points to obtain accurate data on friction mechanical losses., This research has been partially funded by the Spanish government under the grant agreement TRA2017-89894-R. The authors would like to thank different members of the CMT-Motores Térmicos team of the Universitat Politècnica de València fortheir contribution to this work. The authors would also like to thank the Spanish Ministry of Science, Innovation and Universities for financing the PhD. Studies of Antonio J. Jiménez-Reyes (grant FPU18/02116)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Assessing the optimum combustion under constrained conditions

  • Olmeda, P.|||0000-0002-3161-0165
  • Martín, Jaime|||0000-0002-0496-3176
  • Novella Rosa, Ricardo|||0000-0002-5123-6924
  • Blanco-Cavero, Diego
[EN] This work studies the optimum heat release law of a direct injection diesel engine under constrained conditions. For this purpose, a zero-dimensional predictive model of a diesel engine is coupled to an optimization tool used to shape the heat release law in order to optimize some outputs (maximize gross indicated efficiency and minimize NOx emissions) while keeping several restrictions (mechanical limits such as maximum peak pressure and maximum pressure rise rate). In a first step, this methodology is applied under different heat transfer scenarios without restrictions to evaluate the possible gain obtained through the thermal isolation of the combustion chamber. Results derived from this study show that heat transfer has a negative effect on gross indicated efficiency ranging from -4% of the fuel energy (m(f)H(v)), at high engine speed and load, up to -8% m(f)H(v), at low engine speed and load. In a second step, different mechanical limits are applied resulting in a gross indicated efficiency worsening from -1.4% m(f)H(v) up to -2.8% m(f)H(v) compared to the previous step when nominal constraints are applied. In these conditions, a temperature swing coating that covers the piston top and cylinder head is considered obtaining a maximum gross indicated efficiency improvement of +0.5% m(f)H(v) at low load and engine speed. Finally, NOx emissions are also included in the optimization obtaining the expected tradeoff between gross indicated efficiency and NOx. Under this optimization, cutting down the experimental emissions by 50% supposes a gross indicated efficiency penalty up to -8% m(f)H(v) when compared to the optimum combustion under nominal limits, while maintaining the experimental gross indicated efficiency allows to reduce the experimental emissions 30% at high load and 65% at low load and engine speed., This work was partially funded by GM Global R&D and the Government of Spain through Project TRA2017-89894-R. In addition, the authors acknowledge that some equipment used in this work has been partially supported by FEDER project funds (FEDER-ICTS-2012-06), framed in the operational programme of unique scientific and technical infrastructure of the Ministry of Science and Innovation of Spain. Diego Blanco-Cavero is partially supported through contract FPI-S2-2016-1356 of the Programa de Apoyo para la Investigacion y Desarrollo (PAID) of Universitat Politcenica de Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Effect of the exhaust thermal insulation on the engine efficiency and the exhaust temperature under transient conditions

  • Arnau Martínez, Francisco José|||0000-0003-2902-0630
  • Martín, Jaime|||0000-0002-0496-3176
  • Piqueras, P.|||0000-0002-3767-0839
  • Auñón-García, Ángel
[EN] As well as new advances in the after-treatment systems are required to achieve the new pollutant emission requirements, new designs of the exhaust line can be considered in order to increase the engine efficiency and the after-treatment effectiveness. In the present work, a one-dimensional gas dynamic model has been used to carry out a simulation study comparing several exhaust insulation solutions. This solutions include the insulation of the exhaust ports, the exhaust manifold, the internal surface of the turbine volute, the turbine external housing, as well as different combinations of these solutions. A transient analysis has been done in order to evaluate the increment in the exhaust gases temperature, fuel economy and pollutant emission levels over the WLTC (Worldwide harmonized Light vehicles Test Cycle) at three different temperature conditions. As a conclusion, a 12% increment in the turbine outlet gas enthalpy can be achieved by insulating both the exhausts ports and the exhaust manifold. Moreover, more than 30% less pollutant emissions are released to the environment with this setup., The author(s) disclosed receipt of the following financial support for the research, authorship, and/or publication of this article: This research has been partially funded by the European Union's Horizon 2020 Framework Programme for research, technological development and demonstration under grant agreement 723976 ("DiePeR'') and by the Spanish government under the grant agreement TRA2017-89894-R ("Mecoem''). Angel Aunon was supported through the "Apoyo para la investigacion y Desarrollo (PAID)'' grant for doctoral studies (FPI S2 2018 1048) by Universitat Politecnica de Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

One-Dimensional Modeling of Mechanical and Friction Losses Distribution in a Four-Stroke Internal Combustion Engine

  • Tormos, B.|||0000-0002-8852-3783
  • Martín, Jaime|||0000-0002-0496-3176
  • Blanco-Cavero, Diego
  • Jiménez-Reyes, Antonio José
[EN] As the road transport accounts between 15%-18% of worldwide CO2 emissions, the automotive sector has a deep commitment to mitigate global warming. Consequently, stricter regulations have been adopted by the European Union and worldwide to reduce that big impact. Approximately, 10% of the energy generated by fuel combustion in the engine is destined to the auxiliaries components activation and the movement of mechanical elements with relative motion between themselves. A reduction on that figure or alternatively a mechanical efficiency improvement can be directly translated on target alignment. The aim of this work is developing a model to predict the mechanical and friction losses and its distribution in a four-stroke direct injection-diesel engine and simulating different strategies, which increment the engine efficiency. A 1D model has been developed and fitted in GT-SUITE based on the experimental results of a 1.6-L diesel engine. Additionally, a description of the tribological performance has been realized in different parts of the engine where friction is present. Finally, the engine friction maps have been broken down in order to quantify the friction losses produced in the piston ring assembly, crankshaft bearings, and valvetrain