Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 5
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Development and Validation of a Submodel for Thermal Exchanges in the Hydraulic Circuits of a Global Engine Model

  • Broatch, A.|||0000-0001-9991-1039
  • Olmeda, P.|||0000-0002-3161-0165
  • Martín, Jaime|||0000-0002-0496-3176
  • Salvador-Iborra, Josep
[EN] To face the current challenges of the automotive industry, there is a need for computational models capable to simulate the engine behavior under low-temperature and low-pressure conditions. Internal combustion engines are complex and have interconnected systems where many processes take place and influence each other. Thus, a global approach to engine simulation is suitable to study the entire engine performance. The circuits that distribute the hydraulic fluids -liquid fuels, coolants and lubricants- are critical subsystems of the engine. This work presents a 0D model which was developed and set up to make possible the simulation of hydraulic circuits in a global engine model. The model is capable of simulating flow and pressure distributions as well as heat transfer processes in a circuit. After its development, the thermo-hydraulic model was implemented in a physical based engine model called Virtual Engine Model (VEMOD), which takes into account all the relevant relations among subsystems. In the present paper, the thermo-hydraulic model is described and then it is used to simulate oil and coolant circuits of a diesel engine. The objective of the work is to validate the model under steady-state and transient operation, with focus on the thermal evolution of oil and coolant. For validation under steady-state conditions, 22 operating points were measured and simulated, some of them in cold environment. In general, good agreement was obtained between simulation and experiments. Next, the WLTP driving cycle was simulated starting from warmed-up conditions and from ambient temperature. Results were compared with the experiment, showing that modeled trends were close to those experimentally measured. Thermal evolutions of oil and coolant were predicted with mean errors between 0.7 °C and 2.1 °C. In particular, the warm-up phase was satisfactorily modeled., This research has been partially funded by the European Union’s Horizon 2020 Framework Programme for research, technological development and demonstration under grant agreement 723976 (“DiePeR”) and by the Spanish government under the grant agreement TRA2017-89894-R. Josep SalvadorIborra was supported by Universitat Politècnica de València through the contract FPI-S2-2016-1357 of the program PAID01-16. The authors wish to thank Renault SAS, especially P. Mallet and E. Gaïffas, for supporting this research. Jaime Monfort San Segundo is acknowledged for his helpful collaboration in the code implementation
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Tesis doctoral (DoctoralThesis)

A contribution to the global modeling of heat transfer processes in Diesel engines

  • Salvador Iborra, Josep
[EN] Current challenges in research and development of powertrains demand new computational tools capable of simulating vehicle operation under very diverse conditions. This is due, among other reasons, to new homologation standards in the automotive sector requiring compliance of exhaust emissions regulations under any possible driving condition on the road. Global engine or vehicle models provide many advantages to engineers because they allow to reproduce the entire system under study, considering the physical processes that take place in different components and the interactions among them. This thesis aims to enable the modeling of heat transfer processes in a complete engine simulation tool developed at CMT-Motores Térmicos research institute. This 0D/1D simulation tool is called Virtual Engine Model (VEMOD). The development of heat transfer models comprises the engine block and the ancillary systems. The model of heat transfer in the engine block deals with the central problem of in-cylinder convection by means of a combination of experimental research, CFD simulation and multizone 0D modeling. The other thermal processes present in the engine block are examined in order to implement suitable submodels. Once the model is complete, it undergoes a validation with experimental transient tests. Afterwards, the ancillary systems for engine thermal management are brought into focus. These systems are considered by means of two new models: a model of heat exchangers and a model of thermo-hydraulic circuits. The development of those models is reported in detail. Lastly, with the referred thermal models integrated in the global simulation tool, a validation study is undertaken. The goal is to validate the ability of the Virtual Engine Model to capture the thermal response of a real engine under various operating conditions. To achieve that, an experimental campaign combining tests under steady-state operation, under transient operation and at different temperatures is conducted in parallel to the corresponding simulation campaign. The capacity of the global engine simulations to replicate the measured thermal evolution is finally demonstrated., [ES] Los retos actuales en la investigación y desarrollo de trenes de potencia demandan nuevas herramientas computacionales capaces de simular el funcionamento de un vehículo en condiciones muy diversas. Esto se debe, entre otras razones, a que los nuevos estándares de homologación en el sector de la automoción obligan al cumplimiento de las regulaciones de emisiones en cualquier condición posible de conducción en carretera. Los modelos globales de motor o de vehículo proporcionan muchas ventajas a los ingenieros porque permiten reproducir el sistema entero a estudiar, considerando los procesos físicos que tienen lugar en los distintos componentes y las interacciones entre ellos. Esta tesis pretende hacer posible el modelado de los procesos de transmisión de calor en una completa herramienta de simulación de motor desarrollada en el instituto de investigación CMT-Motores Térmicos. Esta herramienta de simulación 0D/1D se denomina Motor Virtual o Virtual Engine Model (VEMOD). El desarrollo de modelos de transmisión de calor comprende el bloque motor y los sistemas auxiliares. El modelo de transmisión de calor en el bloque motor aborda el problema central de la convección en el interior del cilindro mediante una combinación de investigación experimental, simulación CFD y modelado 0D multizona. El resto de procesos térmicos presentes en el bloque motor son examinados para poder implementar submodelos adecuados. Una vez el modelo está terminado, se realiza una validación con ensayos experimentales en régimen transitorio. A continuación, el foco de atención pasa a los sistemas auxiliares de gestión térmica. Estos sistemas se toman en consideración por medio de dos nuevos modelos: un modelo de intercambiadores de calor y un modelo de circuitos termohidráulicos. El desarrollo de los modelos se explica en detalle en esta tesis. Por último, con los citados modelos integrados en el Motor Virtual, se lleva a cabo un estudio de validación. El objectivo es validar la capacidad del Motor Virtual para reproducir la respuesta térmica de un motor real en varias condiciones de funcionamento. Para conseguirlo, se realiza una campaña experimental que combina ensayos en régimen estacionario, en régimen transitorio y a diferentes temperaturas, en paralelo a la campaña de simulación correspondiente. La capacidad de las simulaciones globales de motor para replicar la evolución térmica medida experimentalmente queda finalmente demostrada., [CA] Els reptes actuals en la recerca i el desenvolupament de trens de potència demanden noves eines computacionals capaces de simular el funcionament d'un vehicle en condicions molt diverses. Açò es deu, entre altres raons, a que els nous estàndards d'homologació al sector de l'automoció obliguen al compliment de les regulacions d'emissions en qualsevol condició possible de conducció en carretera. Els models globals de motor o de vehicle proporcionen molts avantatges als enginyers perquè permeten reproduir el sistema sencer a estudiar, considerant els processos físics que tenen lloc als distints components i les interaccions entre ells. Aquesta tesi pretén fer possible el modelat dels processos de transmissió de calor en una completa eina de simulació de motor desenvolupada a l'institut de recerca CMT-Motores Térmicos. Aquesta eina de simulació 0D/1D s'anomena Motor Virtual o Virtual Engine Model (VEMOD). El desenvolupament de models de transmissió de calor comprén el bloc motor i els sistemes auxiliars. El model de transmissió de calor al bloc motor aborda el problema central de la convecció a l'interior del cilindre mitjançant una combinació de recerca experimental, simulació CFD i modelat 0D multizona. La resta de processos tèrmics presents al bloc motor són examinats per a poder implementar submodels adequats. Una vegada el model està acabat, es fa una validació amb assajos experimentals en règim transitori. A continuació, el focus d'atenció passa als sistemes auxiliars de gestió tèrmica. Aquests sistemes es prenen en consideració per mitjà de dos nous models: un model d'intercanviadors de calor i un model de circuits termohidràulics. El desenvolupament dels models s'explica en detall en aquesta tesi. Per últim, amb els referits models integrats al Motor Virtual, es porta a terme un estudi de validació. L'objectiu és validar la capacitat del Motor Virtual per a reproduir la resposta tèrmica d'un motor real en diverses condicions de funcionament. Per a assolir-ho, es realitza una campanya experimental que combina assajos en règim estacionari, en règim transitori i a diferents temperatures, en paral·lel a la campanya de simulació corresponent. La capacitat de les simulacions globals de motor per a replicar l'evolució tèrmica observada experimentalment queda finalment demostrada., European funds received in the framework of Horizon 2020’s DiePeR project have contributed to the validation and improvement of the Virtual Engine Model. My own dedication has been funded by Universitat Politècnica de València through the predoctoral contract FPI-S2-2016-1357 of “Programa de Apoyo para la Investigaci´on y Desarrollo (PAID-01-16)”.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Influence of the number of injections on piston heat rejection under low temperature combustion conditions in an optical compression-ignition engine

  • Tanov, Slavey
  • Salvador-Iborra, Josep
  • Andersson, Öivind
  • Olmeda, P.|||0000-0002-3161-0165
  • García Martínez, Antonio|||0000-0001-5783-4936
[EN] New combustion concepts are being investigated to develop cleaner engines. One of the most promising is partially premixed combustion. The mechanisms of this combustion mode and its impact on performance and emissions have been studied in the previous years. Nevertheless, little research has been done from the point of view of heat transfer. In particular, the influence of the injection strategy on heat transfer is of great interest in partially premixed combustion. This work presents a method to calculate convective heat transfer to the piston. The method uses a combination of gas velocity models and experimental velocity data measured with the PIV technique. This method was applied to achieve the goal of studying the effect of the number of injections on heat rejection. First, the influence of the injection strategy on gas motion was examined. To do that, an analysis of the velocity components relevant to gas-surface convection was conducted, as well as of the resulting heat transfer coefficient. Next, heat flux results were discussed. The single injection strategy showed the highest heat transfer, followed by triple injection and double injection. Important instantaneous variations of heat flux were observed at different locations of the piston bowl. All findings were associated with concurring conditions of high gas velocity, density and temperature., The authors gratefully acknowledge the Swedish Energy Agency Sweden and the Competence Center for Combustion Processes KCFP. The authors also would like to acknowledge that part of the work has been partially funded by the Spanish government under the grant José Castillejo (JC2015/0036). Research leading to this work has also received funding from Universitat Politècnica de València Spain through the contract FPI-S2-2016 1357 of Programa de Apoyo para la Investigación y Desarrollo (PAID-01 16) .
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Color degradation mapping of rock art paintings using microfading spectrometry

  • Carrión-Ruiz, Berta
  • Riutort-Mayol, Gabriel
  • Molada-Tebar, Adolfo
  • Villaverde, Valentín
  • Lerma, José Luis|||0000-0001-9443-9214
[EN] Rock art documentation is a complex task that should be carried out in a complete, rigorous and exhaustive way, in order to take particular actions that allow stakeholders to preserve the archaeological sites under constant deterioration. The pigments used in prehistoric paintings present high light sensitivity and rigorous scientific color degradation mapping is not usually undertaken in overall archaeological sites. Microfading spectrometry is a suitable technique for determining the light-stability of pigments found in rock art paintings in a non-destructive way. Spectral data can be transformed into colorimetric information following the recommendations published by the Commission Internationale de l'Eclairage(CIE). The fading degree can be evaluated through the color changes produced, computing both color and chromatic differences. Microfading Tester (MFT) measurements on spot samples are time-consuming and difficult to materialize on-site. This paper presents the results of statistical Gaussian process interpolation to map the potential MFT spectral variations overtime on a scene full of prehistoric rock art paintings. In addition, a descriptive analysis of color variations that may suffer the rock art motifs overtime has been carried out. The advanced statistical methodology implemented can highlight potential changes on some rock support areas, and stable conditions on the painted red motifs over time, which can help to establish future conservation actions in the archaeological site. (C) 2020 Elsevier Masson SAS. All rights reserved., This research was partially supported by Research and Development Aid Program PAID-01-16 from the Universitat Politècnica de València [FPI-UPV2016 Sub 1 grant].
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Experimental study of the influence of exhaust gas recirculation on heat transfer in the firedeck of a direct injection diesel engine

  • Torregrosa, A. J.|||0000-0003-0933-1626
  • Broatch, A.|||0000-0001-9991-1039
  • Olmeda, P.|||0000-0002-3161-0165
  • Salvador-Iborra, Josep
  • Warey, Alok
[EN] Emissions control is a key topic for internal combustion engine development. One of the most widespread technologies to reduce the formation of nitrogen oxides is the recirculation of exhaust gas to the engine intake. Besides, carbon dioxide emissions from internal combustion engines can be reduced by increasing engine efficiency. A relevant factor for engine efficiency is heat rejection. The interaction between heat transfer and exhaust gas recirculation is not fully understood. In this paper, an experimental study is presented which aims to shed light on the influence of high pressure exhaust gas recirculation on heat transfer. Three operating points were analyzed. Heat flux was calculated at several locations of the firedeck from temperature measurements. The results showed that the influence of exhaust gas recirculation on heat transfer was significant. Reductions of heat flux up to 18% were observed. The largest reduction was found in the area near the center of the firedeck. To contextualize the findings in the framework of emissions reduction, the trade-off between nitrogen oxides and carbon dioxide was assessed for all test points., The authors acknowledge General Motors Global R&D for supporting this research. The equipment used in this work was partially supported by FEDER project funds Dotación de infraestructuras científico técnicas para el Centro Integral de Mejora Energética y Medioambiental de Sistemas de Transporte (CiMeT), (FEDER-ICTS-2012-06) , framed in the operational program of unique scientific and technical infrastructure of the Ministry of Science and Innovation of Spain. Josep Salvador-Iborra was partially supported through contract FPI-S2-2016-1357 of Programa de Apoyo para la Investigación y Desarrollo (PAID-01-16) of Universitat Politècnica de València.