Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 9
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Development and Validation of a Submodel for Thermal Exchanges in the Hydraulic Circuits of a Global Engine Model

  • Broatch, A.|||0000-0001-9991-1039
  • Olmeda, P.|||0000-0002-3161-0165
  • Martín, Jaime|||0000-0002-0496-3176
  • Salvador-Iborra, Josep
[EN] To face the current challenges of the automotive industry, there is a need for computational models capable to simulate the engine behavior under low-temperature and low-pressure conditions. Internal combustion engines are complex and have interconnected systems where many processes take place and influence each other. Thus, a global approach to engine simulation is suitable to study the entire engine performance. The circuits that distribute the hydraulic fluids -liquid fuels, coolants and lubricants- are critical subsystems of the engine. This work presents a 0D model which was developed and set up to make possible the simulation of hydraulic circuits in a global engine model. The model is capable of simulating flow and pressure distributions as well as heat transfer processes in a circuit. After its development, the thermo-hydraulic model was implemented in a physical based engine model called Virtual Engine Model (VEMOD), which takes into account all the relevant relations among subsystems. In the present paper, the thermo-hydraulic model is described and then it is used to simulate oil and coolant circuits of a diesel engine. The objective of the work is to validate the model under steady-state and transient operation, with focus on the thermal evolution of oil and coolant. For validation under steady-state conditions, 22 operating points were measured and simulated, some of them in cold environment. In general, good agreement was obtained between simulation and experiments. Next, the WLTP driving cycle was simulated starting from warmed-up conditions and from ambient temperature. Results were compared with the experiment, showing that modeled trends were close to those experimentally measured. Thermal evolutions of oil and coolant were predicted with mean errors between 0.7 °C and 2.1 °C. In particular, the warm-up phase was satisfactorily modeled., This research has been partially funded by the European Union’s Horizon 2020 Framework Programme for research, technological development and demonstration under grant agreement 723976 (“DiePeR”) and by the Spanish government under the grant agreement TRA2017-89894-R. Josep SalvadorIborra was supported by Universitat Politècnica de València through the contract FPI-S2-2016-1357 of the program PAID01-16. The authors wish to thank Renault SAS, especially P. Mallet and E. Gaïffas, for supporting this research. Jaime Monfort San Segundo is acknowledged for his helpful collaboration in the code implementation
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Tesis doctoral (DoctoralThesis)

A contribution to the global modeling of heat transfer processes in Diesel engines

  • Salvador Iborra, Josep
[EN] Current challenges in research and development of powertrains demand new computational tools capable of simulating vehicle operation under very diverse conditions. This is due, among other reasons, to new homologation standards in the automotive sector requiring compliance of exhaust emissions regulations under any possible driving condition on the road. Global engine or vehicle models provide many advantages to engineers because they allow to reproduce the entire system under study, considering the physical processes that take place in different components and the interactions among them. This thesis aims to enable the modeling of heat transfer processes in a complete engine simulation tool developed at CMT-Motores Térmicos research institute. This 0D/1D simulation tool is called Virtual Engine Model (VEMOD). The development of heat transfer models comprises the engine block and the ancillary systems. The model of heat transfer in the engine block deals with the central problem of in-cylinder convection by means of a combination of experimental research, CFD simulation and multizone 0D modeling. The other thermal processes present in the engine block are examined in order to implement suitable submodels. Once the model is complete, it undergoes a validation with experimental transient tests. Afterwards, the ancillary systems for engine thermal management are brought into focus. These systems are considered by means of two new models: a model of heat exchangers and a model of thermo-hydraulic circuits. The development of those models is reported in detail. Lastly, with the referred thermal models integrated in the global simulation tool, a validation study is undertaken. The goal is to validate the ability of the Virtual Engine Model to capture the thermal response of a real engine under various operating conditions. To achieve that, an experimental campaign combining tests under steady-state operation, under transient operation and at different temperatures is conducted in parallel to the corresponding simulation campaign. The capacity of the global engine simulations to replicate the measured thermal evolution is finally demonstrated., [ES] Los retos actuales en la investigación y desarrollo de trenes de potencia demandan nuevas herramientas computacionales capaces de simular el funcionamento de un vehículo en condiciones muy diversas. Esto se debe, entre otras razones, a que los nuevos estándares de homologación en el sector de la automoción obligan al cumplimiento de las regulaciones de emisiones en cualquier condición posible de conducción en carretera. Los modelos globales de motor o de vehículo proporcionan muchas ventajas a los ingenieros porque permiten reproducir el sistema entero a estudiar, considerando los procesos físicos que tienen lugar en los distintos componentes y las interacciones entre ellos. Esta tesis pretende hacer posible el modelado de los procesos de transmisión de calor en una completa herramienta de simulación de motor desarrollada en el instituto de investigación CMT-Motores Térmicos. Esta herramienta de simulación 0D/1D se denomina Motor Virtual o Virtual Engine Model (VEMOD). El desarrollo de modelos de transmisión de calor comprende el bloque motor y los sistemas auxiliares. El modelo de transmisión de calor en el bloque motor aborda el problema central de la convección en el interior del cilindro mediante una combinación de investigación experimental, simulación CFD y modelado 0D multizona. El resto de procesos térmicos presentes en el bloque motor son examinados para poder implementar submodelos adecuados. Una vez el modelo está terminado, se realiza una validación con ensayos experimentales en régimen transitorio. A continuación, el foco de atención pasa a los sistemas auxiliares de gestión térmica. Estos sistemas se toman en consideración por medio de dos nuevos modelos: un modelo de intercambiadores de calor y un modelo de circuitos termohidráulicos. El desarrollo de los modelos se explica en detalle en esta tesis. Por último, con los citados modelos integrados en el Motor Virtual, se lleva a cabo un estudio de validación. El objectivo es validar la capacidad del Motor Virtual para reproducir la respuesta térmica de un motor real en varias condiciones de funcionamento. Para conseguirlo, se realiza una campaña experimental que combina ensayos en régimen estacionario, en régimen transitorio y a diferentes temperaturas, en paralelo a la campaña de simulación correspondiente. La capacidad de las simulaciones globales de motor para replicar la evolución térmica medida experimentalmente queda finalmente demostrada., [CA] Els reptes actuals en la recerca i el desenvolupament de trens de potència demanden noves eines computacionals capaces de simular el funcionament d'un vehicle en condicions molt diverses. Açò es deu, entre altres raons, a que els nous estàndards d'homologació al sector de l'automoció obliguen al compliment de les regulacions d'emissions en qualsevol condició possible de conducció en carretera. Els models globals de motor o de vehicle proporcionen molts avantatges als enginyers perquè permeten reproduir el sistema sencer a estudiar, considerant els processos físics que tenen lloc als distints components i les interaccions entre ells. Aquesta tesi pretén fer possible el modelat dels processos de transmissió de calor en una completa eina de simulació de motor desenvolupada a l'institut de recerca CMT-Motores Térmicos. Aquesta eina de simulació 0D/1D s'anomena Motor Virtual o Virtual Engine Model (VEMOD). El desenvolupament de models de transmissió de calor comprén el bloc motor i els sistemes auxiliars. El model de transmissió de calor al bloc motor aborda el problema central de la convecció a l'interior del cilindre mitjançant una combinació de recerca experimental, simulació CFD i modelat 0D multizona. La resta de processos tèrmics presents al bloc motor són examinats per a poder implementar submodels adequats. Una vegada el model està acabat, es fa una validació amb assajos experimentals en règim transitori. A continuació, el focus d'atenció passa als sistemes auxiliars de gestió tèrmica. Aquests sistemes es prenen en consideració per mitjà de dos nous models: un model d'intercanviadors de calor i un model de circuits termohidràulics. El desenvolupament dels models s'explica en detall en aquesta tesi. Per últim, amb els referits models integrats al Motor Virtual, es porta a terme un estudi de validació. L'objectiu és validar la capacitat del Motor Virtual per a reproduir la resposta tèrmica d'un motor real en diverses condicions de funcionament. Per a assolir-ho, es realitza una campanya experimental que combina assajos en règim estacionari, en règim transitori i a diferents temperatures, en paral·lel a la campanya de simulació corresponent. La capacitat de les simulacions globals de motor per a replicar l'evolució tèrmica observada experimentalment queda finalment demostrada., European funds received in the framework of Horizon 2020’s DiePeR project have contributed to the validation and improvement of the Virtual Engine Model. My own dedication has been funded by Universitat Politècnica de València through the predoctoral contract FPI-S2-2016-1357 of “Programa de Apoyo para la Investigaci´on y Desarrollo (PAID-01-16)”.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Analysis of temperature and altitude effects on the Global Energy Balance during WLTC

  • Payri, F.|||0000-0002-3314-4911
  • Martín, Jaime|||0000-0002-0496-3176
  • Arnau Martínez, Francisco José|||0000-0003-2902-0630
  • Artham, Sushma
[EN] In this work, the Global Energy Balance (GEB) of a 1.6 L compression ignition engine is analyzed during WLTC using a combination of experimental measurements and simulations, by means of a Virtual Engine. The energy split considers all the relevant energy terms at two starting temperatures (20 degrees C and 7 degrees C) and two altitudes (0 and 1000 m). It is shown that reducing ambient temperature from 20 degrees C to -7 degrees C decreases brake efficiency by 1% and increases fuel consumption by 4%, mainly because of the higher friction due to the higher oil viscosity, while the effect of increasing altitude 1000 m decreases brake efficiency by 0.8% and increases fuel consumption by 2.5% in the WLTC mainly due to the change in pumping. In addition, GEB shows that ambient temperature is affecting exhaust enthalpy by 4.5%, heat rejection to coolant by 2%, and heat accumulated in the block by 2.5%, while altitude does not show any remarkable variations other than pumping and break power., The author(s) disclosed receipt of the following financial support for the research, authorship, and/or publication of this article: This research has been partially funded by the European Union's Horizon 2020 Framework Programme for research, technological development and demonstration under grant agreement 723976 ("DiePeR'') and by the Spanish government under the grant agreement TRA2017-89894-R ("MECOEM'') and Sushma Artham was supported by FPI grant with reference PRE2018-084411. The authors wish to thank Renault SAS, especially P. Mallet and E. Gaiffas, for supporting this research.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Lumped Approach for Flow-Through and Wall-Flow Monolithic Reactors Modelling for Real-Time Automotive Applications

  • Payri, F.|||0000-0002-3314-4911
  • Arnau Martínez, Francisco José|||0000-0003-2902-0630
  • Piqueras, P.|||0000-0002-3767-0839
  • Ruiz Lucas, María José
[EN] The increasingly restrictive legislation on pollutant emissions is involving new homologation procedures driven to be representative of real driving emissions. This context demands an update of the modelling tools leading to an accurate assessment of the engine and aftertreatment systems performance at the same time as these complex systems are understood as a single element. In addition, virtual engine models must retain the accuracy while reducing the computational effort to get closer to real-time computation. It makes them useful for pre-design and calibration but also potentially applicable to on-board diagnostics purposes. This paper responds to these requirements presenting a lumped modelling approach for the simulation of aftertreatment systems. The basic principles of operation of flow-through and wall-flow monoliths are covered leading the focus to the modelling of gaseous emissions conversion efficiency and particulate matter abatement, i.e. filtration and regeneration processes. The model concept is completed with the solution of pressure drop and heat transfer processes. The lumped approach hypotheses and the solution of the governing equations for every sub-model are detailed. While inertial pressure drop contributions are computed from the characteristic pressure drop coefficient, the porous medium effects in wall-flow monoliths are considered separately. Heat transfer sub-model applies a nodal approach to account for heat exchange and thermal inertia of the monolith substrate and the external canning. In wall-flow monoliths, the filtration and porous media properties are computed as a function of soot load applying a spherical packed bed approach. The soot oxidation mechanism including adsorption reactant phase is presented. Concerning gaseous emissions, the general scheme to solve the chemical species transport in the bulk gas and washcoat regions is also described. In particular, it is finally applied to the modelling of CO and HC abatement in a DOC and DPF brick. The model calibration steps against a set of steady-state in-engine experiments allowing separate certain phenomena are discussed. As a final step, the model performance is assessed against a transient test during which all modelled processes are taking place simultaneously under highly dynamic driving conditions. This test is simulated imposing different integration time-steps to demonstrate the model’s potential for real-time applications., This research has been partially supported by FEDER and the Government of Spain through project TRA2016-79185-R and by the European Union’s Horizon 2020 Framework Programme for research, technological development and demonstration under grant agreement number 723976.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Tesis doctoral (DoctoralThesis)

Contribution to the simulation of new standard testing cycles by means of a 0D/1D tool

  • Artham, Sushma
[ES] El objetivo principal de esta tesis es establecer una metodología para predecir el consumo de combustible y las emisiones de un motor de encendido por compresión en condiciones transitorias. Además, su objetivo es explorar cómo las diferentes configuraciones del motor y los factores ambientales impactan el comportamiento del motor utilizando un enfoque de modelado 0D/1D. Además, el estudio pretende extender esta metodología a los motores duales, analizando específicamente las características de combustión de metano-diésel e hidrógeno-diésel. Para lograrlo, la herramienta de modelado 0D/1D se ajustó y validó meticulosamente utilizando un motor diésel de cuatro cilindros. Esta alineación entre la simulación y datos experimentales se centró especialmente en factores cruciales como la presión, la liberación de calor, las temperaturas en los fluidos del motor y el par. Se realizó un análisis exhaustivo del Balance Energético Global (GEB) utilizando VEMOD (Virtual Engine Model). Este análisis proporcionó información detallada sobre el consumo del motor y su reacción en diversas condiciones de funcionamiento, particularmente durante el Ciclo de ensayo mundial armonizado de vehículos ligeros (WLTC). La comparación de términos energéticos entre diferentes condiciones ambientales y de motor destacó aspectos como la fricción, la transferencia de calor y la acumulación de calor. Además, el análisis GEB permitió explorar cómo se distribuía la energía con diferentes temperaturas y altitudes ambientes. El estudio también evaluó las emisiones de NOx, revelando patrones influenciados por factores como las tasas de recirculación de gases de escape (EGR) y la temperatura de admisión. En el ámbito de los motores de combustible dual, se elaboró y validó un modelo de combustión utilizando la herramienta de simulación 0D/1D. La atención inicial se centró en la combustión de metano-Diesel, validada con datos experimentales. Posteriormente, el alcance de este modelo se amplió para simular la combustión de hidrógeno-Diesel. Esta tesis ha introducido con éxito una metodología que utiliza VEMOD para predecir el consumo y las emisiones del motor en distintos escenarios. El análisis exhaustivo arrojó luz sobre cómo funcionan los mecanismos de distribución de energía y cómo diferentes factores influyen en el comportamiento del motor. La aplicación de esta metodología a motores de encendido por compresión ha demostrado su versatilidad y capacidad de predicción, lo que la convierte en una herramienta valiosa para investigar escenarios futuros, también con combustiones duales., [CA] L'objectiu principal d'aquesta tesi és establir una metodologia per predir el consum de combustible i les emissions d'un motor d'encesa per compressió en condicions transitòries. A més, pretén explorar com diferents configuracions de motors i factors ambientals afecten el comportament del motor mitjançant un enfocament de modelització 0D/1D. A més, l'estudi s'esforça a estendre aquesta metodologia als motors de doble combustible (duals), analitzant específicament les característiques de combustió de metà-dièsel i hidrogendièsel. Per aconseguir-ho, l'eina de modelització 0D/1D es va ajustar minuciosament i es va validar mitjançant un motor dièsel de quatre cilindres. Aquesta alineació entre dades de simulació i món real es va centrar especialment en factors crucials com la pressió, l'alliberament de calor, les temperatures dels fluids del motor i el parell. Es va realitzar una anàlisi completa del Balanç Global d'Energia (GEB) mitjançant VEMOD (Virtual Engine Model). Aquesta anàlisi va proporcionar una visió profunda sobre el consum del motor i la seua reacció en diverses condicions de funcionament, especialment durant el Cicle mundial d'assaig de vehicles lleugers harmonitzats (WLTC). La comparació de termes energètics entre diferents condicions ambientals i del motor van posar de manifest aspectes com la fricció, la transferència de calor i l'acumulació de calor. A més, l'anàlisi GEB va explorar com es va distribuir l'energia amb diferents temperatures i altituds ambientals. L'estudi també va valorar les emissions de NOx, revelant patrons influenciats per factors com la recirculació de gasos d'escapament (EGR) i la temperatura d'admissió. En l'àmbit dels motors duals, es va elaborar i validar un model de combustió mitjançant l'eina de simulació 0D/1D. El focus inicial es va centrar en la combustió metà-Diesel, validada amb dades experimentals. Posteriorment, l'abast d'aquest model es va ampliar per simular la combustió hidrogen-Diesel. Aquesta tesi ha introduït amb èxit una metodologia que utilitza VEMOD per predir el consum i les emissions del motor en diferents escenaris. L'anàlisi completa va donar llum a com funcionen els mecanismes de distribució d'energia i com diferents factors influeixen en el comportament del motor. L'aplicació d'aquesta metodologia als motors d'encesa per compressió va demostrar la seva versatilitat i capacitats de predicció, convertint-la en una valuosa eina per investigar els futurs escenaris, fins i tot amb combustions duals., [EN] The main aim of this thesis is to establish a methodology for predicting fuel consumption and emissions of a compression ignition engine in transient conditions. Additionally, it aims to explore how different engine setups and environmental factors impact the engine's performance using a 0D/1D modelling approach. Moreover, the study strives to extend this methodology to dual fuel engines, specifically analysing methane-Diesel and hydrogen- Diesel combustion characteristics. The 0D/1D modelling tool was meticulously fine-tuned and validated using a four-cylinder Diesel engine to achieve this. This alignment between simulation and experimental data focused on crucial factors such as pressure, heat release, engine fluid temperatures and torque. A comprehensive Global Energy Balance (GEB) analysis was conducted using VEMOD (Virtual Engine Model). This analysis provided insights into the engine consumption and performance under diverse operating conditions, particularly during the Worldwide Harmonized Light Vehicles Test Cycle (WLTC). The comparison of energy terms across different engine and boundary conditions highlighted aspects such as friction, heat rejection, and heat accumulation. Additionally, the GEB analysis allowed exploration of how energy was split across varying ambient temperatures and altitudes. The study also assessed NOx emissions, revealing patterns influenced by factors such as Exhaust Gas Recirculation (EGR) rates and intake temperature. A combustion model was developed and validated using the 0D/1D simulation tool in the scope of dual fuel engines. The initial focus was on methane-Diesel combustion, validated against experimental data. Subsequently, this model scope was expanded to simulate hydrogen-Diesel combustion. This thesis has successfully introduced a methodology based on VEMOD to predict engine consumption and emissions across varying scenarios. The comprehensive analysis illuminated how energy distribution mechanisms operate and how factors influence engine performances. The application of this methodology to compression ignition engines demonstrated its versatility and prediction capabilities, making it a valuable tool for investigating future combustion scenarios, including dual fuel operation., This research has been partially funded by the European Union’s Horizon 2020 Framework Programme for research, technological development and demonstration under grant agreement 723976 (“DiePeR”) and by the Spanish government under the grant agreement TRA2017-89894-R (”MECOEM”) and I was supported by FPI grant with reference PRE2018-084411.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Diesel engine optimization and exhaust thermal management by means of variable valve train strategies

  • Arnau Martínez, Francisco José|||0000-0003-2902-0630
  • Martín, Jaime|||0000-0002-0496-3176
  • Pla Moreno, Benjamín|||0000-0001-9238-2939
  • Auñón-García, Ángel
[EN] Due to the need to achieve a fast warm-up of the after-treatment system in order to fulfill the pollutant emission regulations, a growing interest has arisen to adopt variable valve timing technology for automotive engines. Several variable valve timing strategies can be used to achieve an increment in the after-treatment upstream temperature by increasing the residual gas amount. In this study, a one-dimensional gas dynamics engine model has been used to carry out a simulation study comparing several exhaust variable valve actuation strategies. A steady-state analysis has been done in order to evaluate the potential of the different strategies at different operating points. Finally, the effect on the after-treatment warm-up, fuel economy and pollutant emission levels was evaluated over the worldwide harmonized light vehicles test cycle. As a conclusion, the combination of an advanced exhaust (early exhaust valve opening and early exhaust valve closing) and a delayed intake (late intake valve opening and late intake valve closing) presented the best trade-off between exhaust temperature increment and fuel consumption, which achieved a mean temperature increment during low-speed phase of the worldwide harmonized light vehicles test cycle of 27¿°C with a fuel penalty of 6%. The exhaust valve re-opening technique offers a worse trade-off. However, the exhaust valve re-opening leads to lower nitrogen oxide (29% less) and carbon monoxide (11% less) pollutant emissions., The author(s) disclosed receipt of the following financial support for the research, authorship, and/or publication of this article: This research has been partially funded by the European Union's Horizon 2020 Framework Programme for research, technological development and demonstration under grant agreement 723976 ("DiePeR") and by the Spanish government under the grant agreement TRA2017-89894-R. The authors want to acknowledge the "Apoyo para la investigacion y Desarrollo (PAID)," grant for doctoral studies (FPI S2 2018 1048), of Universitat Politecnica de Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Development of an Integrated Virtual Engine Model to Simulate New Standard Testing Cycles

  • Martín, Jaime|||0000-0002-0496-3176
  • Arnau Martínez, Francisco José|||0000-0003-2902-0630
  • Piqueras, P.|||0000-0002-3767-0839
  • Auñón-García, Ángel
[EN] The combination of more strict regulation for pollutant and CO2 emissions and the new testing cycles, covering a wider range of transient conditions, makes very interesting the development of predictive tools for engine design and pre-calibration. This paper describes a new integrated Virtual Engine Model (VEMOD) that has been developed as a standalone tool to simulate new standard testing cycles. The VEMOD is based on a wave-action model that carries out the thermo-and fluid dynamics calculation of the gas in each part of the engine. In the model, the engine is represented by means of 1D ducts, while the volumes, such as cylinders and reservoirs, are considered as 0D elements. Different sub-models are included in the VEMOD to take into account all the relevant phenomena. Thus, the combustion process is calculated by the Apparent Combustion Time (ACT) 1D model, responsible for the prediction of the rate of heat release and NOx formation. Experimental correlations are used to determine the rest of pollutants. In order to predict tailpipe pollutant emissions to the ambient, different sub-models have been developed to reproduce the behavior of the aftertreatment devices (DOC and DPF) placed in the exhaust system. Dedicated friction and auxiliaries sub-models allow obtaining the brake power. The turbocharger consists of 0D compressor and turbine sub-models capable of extrapolating the available maps of both devices. The VEMOD includes coolant and lubricant circuits linked, on the one hand, with the engine block and the turbocharger through heat transfer lumped models; and on the other hand with the engine heat exchangers. A control system emulating the ECU along with vehicle and driver sub-models allow completing the engine simulation. The Virtual Engine Model has been validated with experimental tests in a 1.6 L Diesel engine using steady and transient tests in both hot and cold conditions. Engine torque was predicted with a mean error of 3 Nm and an error below 14 Nm for 90 % of the cycle duration. CO2 presented a mean error of 0.04 g/s, while during 80 % of the cycle, error was below 0.44 g/s., This research has been partially funded by the European Union’s Horizon 2020 Framework Programme for research, technological development and demonstration under grant agreement 723976 (“DiePeR”) and by the Spanish government under the grant agreement TRA2017-89894-R. The authors wish to thank Renault SAS, especially P. Mallet and E. Gaïffas, for supporting this research.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Analysis of the energy balance during World harmonized Light vehicles Test Cycle in warmed and cold conditions using a Virtual Engine

  • Olmeda, P.|||0000-0002-3161-0165
  • Martín, Jaime|||0000-0002-0496-3176
  • Arnau Martínez, Francisco José|||0000-0003-2902-0630
  • Artham, Sushma
[EN] In recent years, the interests on transient operation and real driving emissions have increased because of the global concern about environmental pollution that has led to new emissions regulation and new standard testing cycles. In this framework, it is mandatory to focus the engines research on the transient operation, where a Virtual Engine has been used to perform the global energy balance of a 1.6-L diesel engine during a World harmonized Light vehicles Test Cycle. Thus, the energy repartition of the chemical energy has been described with warmed engine and cold start conditions, analyzing in detail the mechanisms affecting the engine consumption. The first analysis focuses on the ¿delay¿ effect affecting the instantaneous energy balance due to the time lag between the in-cylinder processes and pipes: as a main conclusion, it is obtained that it leads to an apparent unbalance than can reach more than 10% of the cumulated fuel energy at the beginning of the cycle, becoming later negligible. Energy split analysis in cold starting World harmonized Light vehicles Test Cycle shows that in this condition the energy accumulation in the block is a key term at the beginning (about 50%) that diminishes its weight until about 10% at the end of the cycle. In warmed conditions, energy accumulation is negligible, but the heat transfer to coolant and oil are higher than in cold starting conditions (21% vs 28%). The lower values of the mean brake efficiency at the beginning of the World harmonized Light vehicles Test Cycle (only about 20%) is affected, especially in cold starting, by the higher mechanical losses due to the higher oil viscosity and the heat rejection from the gases. The friction plays an important role only during the first half of the cycle, with a percentage of about 65% of the total mechanical losses and 10% of the total fuel energy at the end of the World harmonized Light vehicles Test Cycle. However, at the end of the cycle, it does not affect dramatically the mean brake efficiency which is about 31% both in cold starting and warmed World harmonized Light vehicles Test Cycle., The author(s) disclosed receipt of the following financial support for the research, authorship and/or publication of this article: This research has been partially funded by the European Union's Horizon 2020 Framework Programme for research, technological development and demonstration under grant agreement 723976 ("DiePeR'') and by the Spanish government under the grant agreement TRA2017-89894-R. The authors wish to thank Renault SAS, especially P. Mallet and E. Gaiffas, for supporting this research.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Effect of the exhaust thermal insulation on the engine efficiency and the exhaust temperature under transient conditions

  • Arnau Martínez, Francisco José|||0000-0003-2902-0630
  • Martín, Jaime|||0000-0002-0496-3176
  • Piqueras, P.|||0000-0002-3767-0839
  • Auñón-García, Ángel
[EN] As well as new advances in the after-treatment systems are required to achieve the new pollutant emission requirements, new designs of the exhaust line can be considered in order to increase the engine efficiency and the after-treatment effectiveness. In the present work, a one-dimensional gas dynamic model has been used to carry out a simulation study comparing several exhaust insulation solutions. This solutions include the insulation of the exhaust ports, the exhaust manifold, the internal surface of the turbine volute, the turbine external housing, as well as different combinations of these solutions. A transient analysis has been done in order to evaluate the increment in the exhaust gases temperature, fuel economy and pollutant emission levels over the WLTC (Worldwide harmonized Light vehicles Test Cycle) at three different temperature conditions. As a conclusion, a 12% increment in the turbine outlet gas enthalpy can be achieved by insulating both the exhausts ports and the exhaust manifold. Moreover, more than 30% less pollutant emissions are released to the environment with this setup., The author(s) disclosed receipt of the following financial support for the research, authorship, and/or publication of this article: This research has been partially funded by the European Union's Horizon 2020 Framework Programme for research, technological development and demonstration under grant agreement 723976 ("DiePeR'') and by the Spanish government under the grant agreement TRA2017-89894-R ("Mecoem''). Angel Aunon was supported through the "Apoyo para la investigacion y Desarrollo (PAID)'' grant for doctoral studies (FPI S2 2018 1048) by Universitat Politecnica de Valencia.