Skip to main content

DESARROLLO DE HERRAMIENTAS EXPERIMENTALES Y COMPUTACIONALES PARA LA CARACTERIZACION DE SISTEMAS DE POST-TRATAMIENTO DE GASES DE ESCAPE EN MOTORES DE ENCENDIDO POR COMPRESION

TRA2016-79185-R

•
Funding agency name Agencia Estatal de Investigación
Funding agency acronym AEI
Program Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Call Proyectos I+D+i Retos de Investigación
Call year 2016
State Plan 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Beneficiary centre UNIVERSITAT POLITÈCNICA DE VALÈNCIA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 26
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Lumped Approach for Flow-Through and Wall-Flow Monolithic Reactors Modelling for Real-Time Automotive Applications

  • Payri, F.|||0000-0002-3314-4911
  • Arnau Martínez, Francisco José|||0000-0003-2902-0630
  • Piqueras, P.|||0000-0002-3767-0839
  • Ruiz Lucas, María José
[EN] The increasingly restrictive legislation on pollutant emissions is involving new homologation procedures driven to be representative of real driving emissions. This context demands an update of the modelling tools leading to an accurate assessment of the engine and aftertreatment systems performance at the same time as these complex systems are understood as a single element. In addition, virtual engine models must retain the accuracy while reducing the computational effort to get closer to real-time computation. It makes them useful for pre-design and calibration but also potentially applicable to on-board diagnostics purposes. This paper responds to these requirements presenting a lumped modelling approach for the simulation of aftertreatment systems. The basic principles of operation of flow-through and wall-flow monoliths are covered leading the focus to the modelling of gaseous emissions conversion efficiency and particulate matter abatement, i.e. filtration and regeneration processes. The model concept is completed with the solution of pressure drop and heat transfer processes. The lumped approach hypotheses and the solution of the governing equations for every sub-model are detailed. While inertial pressure drop contributions are computed from the characteristic pressure drop coefficient, the porous medium effects in wall-flow monoliths are considered separately. Heat transfer sub-model applies a nodal approach to account for heat exchange and thermal inertia of the monolith substrate and the external canning. In wall-flow monoliths, the filtration and porous media properties are computed as a function of soot load applying a spherical packed bed approach. The soot oxidation mechanism including adsorption reactant phase is presented. Concerning gaseous emissions, the general scheme to solve the chemical species transport in the bulk gas and washcoat regions is also described. In particular, it is finally applied to the modelling of CO and HC abatement in a DOC and DPF brick. The model calibration steps against a set of steady-state in-engine experiments allowing separate certain phenomena are discussed. As a final step, the model performance is assessed against a transient test during which all modelled processes are taking place simultaneously under highly dynamic driving conditions. This test is simulated imposing different integration time-steps to demonstrate the model’s potential for real-time applications., This research has been partially supported by FEDER and the Government of Spain through project TRA2016-79185-R and by the European Union’s Horizon 2020 Framework Programme for research, technological development and demonstration under grant agreement number 723976.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Late Fuel Post-Injection Influence on the Dynamics and Efficiency of Wall-Flow Particulate Filters Regeneration

  • Serrano, J.R.|||0000-0003-0692-3917
  • Piqueras, P.|||0000-0002-3767-0839
  • De La Morena, Joaquín|||0000-0003-0208-508X
  • Sanchis, Enrique José|||0000-0002-6856-8992
[EN] Late fuel post-injections are the most usual strategy to reach high exhaust temperature for the active regeneration of diesel particulate filters. However, it is important to optimise these strategies in order to mitigate their negative effect on the engine fuel consumption. This work aims at understanding the influence of the post-injection parameters, such as its start of injection and its fuel quantity, on the duration of the regeneration event and the fuel consumption along it. For this purpose, a set of computational models are employed to figure out in a holistic way the involved phenomena in the interaction between the engine and the exhaust gas aftertreatment system. Firstly, an engine model is implemented to evaluate the effect of the late fuel post-injection pattern on the gas properties at the exhaust aftertreatment system inlet in different steady-state operating conditions. These are selected to provide representative boundary conditions of the exhaust gas flow concerning dwell time, exhaust temperature and O2 concentration. In this way, the results are later applied to the analysis of the diesel oxidation catalyst and wall-flow particulate filter responses. The dependence of the diesel particulate filter (DPF) inlet temperature is discussed based on the efficiency of each post-injection strategy to increase the exhaust gas temperature. Next, the influence on the dynamics of the regeneration of the post-injection parameters through the change in gas temperature and O2 concentration is finally studied distinguishing the pre-heating, maximum reactivity and late soot oxidation stages as well as the required fuel consumption to complete the regeneration process., This work has been partially supported by FEDER and the Ministerio de Ciencia, Innovacion y Universidades of the Government of Spain through Grant No. TRA2016-79185-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

A holistic methodology to correct heat transfer and bearing friction losses from hot turbocharger maps in order to obtain adiabatic efficiency of the turbomachinery

  • Serrano, J.R.|||0000-0003-0692-3917
  • Olmeda, P.|||0000-0002-3161-0165
  • Arnau Martínez, Francisco José|||0000-0003-2902-0630
  • Samala, Vishnu
[EN] Turbocharger performance maps provided by manufacturers are usually far from the assumption of reproducing the isentropic performance. The reason being, those maps are usually measured using a hot gas stand. The definition of the effective turbocharger efficiency maps include the mechanical losses and heat transfer that has occurred during the gas stand test for the turbine maps and only the heat transfer for the compressor maps. Thus, a turbocharger engine model that uses these maps provides accurate results only when simulating turbocharger operative conditions similar to those at which the maps are recorded. However, for some critical situations such as Worldwide harmonized Light vehicles Test Cycles (WLTC) driving cycle or off-design conditions, it is difficult to ensure this assumption. In this article, an internal and external heat transfer model combined with mechanical losses model, both previously developed and calibrated, has been used as an original tool to ascertain a calculation procedure to obtain adiabatic maps from diabatic standard turbocharger maps. The turbocharger working operative conditions at the time of map measurements and geometrical information of the turbocharger are necessary to discount both effects precisely. However, the maps from turbocharger manufacturers do not include all required information. These create additional challenges to develop the procedure to obtain approximated adiabatic maps making some assumptions based on SAE standards for non-available data. A sensitivity study has been included in this article to check the validity of the hypothesis proposed by changing the values of parameters which are not included in the map data. The proposed procedure becomes a valuable tool either for Original Equipment Manufacturers (OEMs) to parameterize turbocharger performance accurately for benchmarking and turbocharged engine design or to turbocharger manufacturers to provide much-appreciated information of their performance maps., The author(s) disclosed receipt of the following financial support for the research, authorship and/or publication of this article: This work has been partially supported by FEDER and the Government of Spain through Grant No. TRA2016-79185-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Turbine and exhaust ports thermal insulation impact on the engine efficiency and aftertreatment inlet temperature

  • Luján, José M.|||0000-0001-6133-8943
  • Serrano, J.R.|||0000-0003-0692-3917
  • Piqueras, P.|||0000-0002-3767-0839
  • Diesel Costa, Barbara
[EN] Worldwide emission regulations are driven the efforts of the automotive industry to meet challenging targets concerning pollution reduction. Nowadays, advances in exhaust aftertreatment systems are primarily required to achieve regulation requirements within the whole engine operating range. Nevertheless, flow parameters, such as the exhaust gas temperature, must be also addressed. This makes engine calibration a fundamental step, but also leads to reconsider the passive design of the exhaust line as a way to improve the engine efficiency. Under this context, a study has been conducted to explore the benefits of heat losses limitation looking for aftertreatment inlet temperature increase at the same time fuel economy is improved. To do so, a baseline diesel engine has been modeled using a gas dynamic software taking special care of the heat transfer processes in the exhaust. The investigation covers the definition of different strategies for exhaust ports and turbine thermal insulation, which are evaluated in a representative range of steady-state operating conditions. As a first step, the theoretical limits and representative technology solutions are considered for each exhaust region. Then, a combination of the most promising strategies has been computed to provide a comprehensive database and analysis of the potential of passive exhaust heat losses control., This research has been partially supported by FEDER and the Government of Spain through project TRA2016-79185-R. Additionally, the Ph.D. student Bárbara Diesel has been funded by a grant from the Government of Generalitat Valenciana with reference ACIF/2018/109.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

A modelling tool for engine and exhaust aftertreatment performance analysis in altitude operation

  • Serrano, J.R.|||0000-0003-0692-3917
  • Piqueras, P.|||0000-0002-3767-0839
  • Sanchis, Enrique José|||0000-0002-6856-8992
  • Diesel Costa, Bárbara
[EN] New regulation standards on engine pollutant emissions are widening the engine operating conditions subjected to type approval tests as a way to prevent from the gap between regulated and real-driving emissions. In this regard, ambient temperature and driving altitude are new boundaries to be considered. Although the basis of the impact of these variables has been studied concerning the engine performance, new challenges appear to meet the emission limits and the aftertreatment conversion efficiency. In this work, a gas dynamic modelling tool is approached to explore the maximisation of the engine torque when operating at high altitude in a wide range of ambient temperatures. Particular focus is put on the modelling of the combustion, the turbocharger and the exhaust aftertreatment system. Starting from a sea-level calibration, the proposed methodology accounts for mechanical criteria as well as the impact on the engine raw emissions and exhaust flow properties to define new combustion settings for altitude operation. Next, these boundaries are applied to the exhaust aftertreatment system to analyse the impact on the catalyst conversion efficiency and the particulate filter performance concerning pressure drop and filtration efficiency., This research has been partially supported by FEDER and the Government of Spain through project TRA2016-79185-R. Additionally, the Ph.D. student Bárbara Diesel has been funded by a grant from the Government of Generalitat Valenciana with reference ACIF/2018/109.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Experimental procedure for the characterization of turbocharger s waste-gate discharge coefficient

  • Serrano, J.R.|||0000-0003-0692-3917
  • Arnau Martínez, Francisco José|||0000-0003-2902-0630
  • Tiseira, Andrés-Omar|||0000-0001-9472-2386
  • Samala, Vishnu
[EN] Nowadays, the turbocharger has become one of the key components for automotive spark-ignition engine improvements (fed with both liquid and gaseous fuels), as a support for the boosting and downsizing concept to reduce fuel consumption and exhaust emission. In gasoline engines, the usage of the waste-gate valve typically regulates the maximum boost pressure in the turbocharger system, to protect the engine and the turbocharger at high engine speeds. To improve the transient response at low engine speeds two-stage turbocharger is widely used. Two-stage systems are composed of several valves to regulate the flow to control the boosting of the system. Like, a by-pass valve between the turbines, a check valve between the compressor and a waste-gate valve for the low-pressure turbines. This paper deals with a methodology for characterizing the discharge coefficient of an electronic waste-gate valve in the turbocharger. To estimate the gas flow over the same in one-dimensional models, an empirical model is correlated and validated. For this, a constant stream experimental work has been carried out on a test rig at different valve position openings, with high turbine inlet temperatures. Finally, an optimal MAP of discharge coefficient has been drawn out through interpolation method, which can integrate into the full one-dimensional turbocharged engine model system, to calculate the actual mass flow through the waste-gate valve., The author(s) disclosed receipt of the following financial support for the research, authorship, and/or publication of this article: This work was partially funded by FEDER and Government of Spain through Project TRA2016-79185-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Sensitivity of pollutants abatement in oxidation catalysts to the use of alternative fuels

  • Piqueras, P.|||0000-0002-3767-0839
  • Ruiz-Lucas, María José
  • Martin Herreros, Jose
  • Tsolakis, Athanasios
[EN] The aim to reduce well to wheel emissions incentives the utilisation of alternative fuels (low to zero carbon content and/or low well to tank emissions) as well as the enhancement of engine efficiency. In parallel, the reduction of engine tailpipe emissions brings new challenges such as the decrease of the exhaust gas temperature. This trend penalises the ability of the exhaust aftertreatment system to eliminate pollutant emissions. In addition, the combustion of alternative fuels and new combustion modes induce changes in the nature and concentration of the exhaust species, which is known to affect the pollutants abatement mechanisms. This investigation provides new understanding on the sensitivity of pollutants abatement in oxidation catalysts to the use of alternative fuels. The studied fuels are conventional diesel, alternative fuels (rapeseed methyl ester and gas to liquid) as well as propane using a dual-fuel combustion strategy. The research combines experimental conversion efficiency from genuine exhaust gases with modelling work useful to explain the reasons for the change in light-off temperature as a function of the fuel. In addition to the CO and NO impact, HC surrogates are proposed distinguishing species of different reactivity for each fuel based on the experimental HC speciation. The results highlight the role of the engine-out emissions on the pollutants conversion efficiency. Their fashion with different fuels contributes to evidence the interest for low engine-out emissions along with low light alkanes content in total HC, as promoted by alternative fuels, to reduce the oxidation light-off temperature., This research has been partially supported by FEDER and the Government of Spain through project TRA2016-79185-R and by Universitat Politecnica de Valencia under a grant with reference number FPI-2018-S2-10 to the Ph.D. student Maria Jose Ruiz
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Turbocharger turbine rotor tip leakage loss and mass flow model valid up to extreme off-design conditions with high blade to jet speed ratio

  • Serrano, J.R.|||0000-0003-0692-3917
  • Navarro, Roberto|||0000-0003-2587-4954
  • García-Cuevas González, Luis Miguel|||0000-0001-9340-0617
  • Inhestern, Lukas Benjamin
[EN] Due to the power consumption restriction of the turbocharger compressor, common turbine maps are rather narrow. To extrapolate them, reliable physical submodels are needed that are valid for broad ranges. Plenty of research has been done referring to tip leakage losses in axial and traditional radial turbomachinery. However, less effort has been put into the tip leakage analysis of radial turbocharger turbines, whose characteristics including high rotational speed and geometry are rather different. Commonly developed tip leakage loss models in radial turbines are mainly based on correlations with the rotational speed, while in axial turbomachinery they are mainly based on blade loading assumptions. Wide range computational fluid dynamics (CFD) data of a medium sized automotive turbine have been used to analyze tip leakage mass flow under extremely diverse running conditions. To be able to fit a model in a broad range of the map, blade loading and rotational speed have to be considered. A novel tip clearance model has been derived from the Navier Stokes Equations. The model owns a dependency on the rotational speed and the blade loading. With this approach CFD data have been fitted in a very good quality to model the tip leakage mass flow rate and tip leakage losses., The work has been partially supported by FEDER and the Spanish Ministry of Economy and Competitiveness through grant number TRA2016-79185-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Tesis de maestría (MasterThesis)

Estudio de la importancia de un modelo de turbogrupos integral para la simulación de la operación en transitorio de carga de los motores Diesel turbo-sobrealimentados

  • Gómez-Vilanova, Alejandro|||0000-0002-6627-7075
[ES] Los motores de combustión turbosobrealimentados son los principales propulsores de los vehículos actuales. Continuar estudiando el acoplamiento entre el turbogrupo y el motor alternativo es fundamental para mejorar su eficiencia y reducir las emisiones contaminates de los mismos. En este TFM se analiza la importancia de usar modelos integrales (holísticos) del turbogrupo. Por modelo integral se entiende aquel que aborda tres aspectos: Eficiencia aerodinámica de las turbomáquinas, pérdidas mecánicas del eje del turbogrupo y fenómenos de transmisión de calor en el turbogrupo. En la actualidad no existen modelos comerciales que aborden los tres aspectos de manera combinada, lo que dificulta enormemente el modelado numérico con precisión de los motores turbo-sobrealimentados. En el TFM se analiza las ventajas de usar este tipo de modelos frente a la práctica standard con el foco en la buena predicción de la contrapresión de escape del motor y la temperatura del aire y los gases de escape a la salida de las turbomáquinas. Este análisis se hace para un motor Diesel con EGR de baja presión y tanto para funcionamiento estacionario como transitorio. Una parte importante del trabajo ha consistido en proponer un protocolo de calibración de los modelos 1D para este tipo de motores. Además se proponen nuevos submodelos para abordar los procesos de transmisión de calor en turbogrupos con características innovadoras como son los compresores con voluta refrigerada y los e-chargers (turbocompresores eléctricos)., [EN] Turbocharged combustion engines are the main engines of current vehicles. Continuing to study the coupling between the turbogroup and the alternative engine is fundamental to improve its efficiency and reduce pollutant emissions from them. In this TFM the importance of using integral (holistic) models of the turbogroup is analyzed. Integral model refers to one that addresses three aspects: aerodynamic efficiency of turbomachinery, mechanical losses of the turbogroup axis and heat transfer phenomena in the turbogroup. At present there are no commercial models that address all three aspects in a combined manner, which makes it extremely difficult to numerically model the turbo-supercharged engines with precision. In the TFM, the advantages of using this type of models in comparison with the standard practice are analyzed with the focus on the good prediction of the exhaust back pressure of the engine and the temperature of the air and the exhaust gases at the exit of the turbomachines. This analysis is made for a diesel engine with low pressure EGR and for both stationary and transient operation. An important part of the work has been to propose a calibration protocol for the 1D models for this type of engine. In addition, new submodels are proposed to address heat transfer processes in turbogroups with innovative features such as compressors with refrigerated volute and e-chargers (electric turbochargers), This work was partially funded by FEDER and Government of Spain through Project TRA2016-79185-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Design, Optimization, and Analysis of Supersonic Radial Turbines

  • Inhestern, Lukas Benjamin
  • Braun, James
  • Paniagua, Guillermo
  • Serrano, J.R.|||0000-0003-0692-3917
[EN] New compact engine architectures such as pressure gain combustion require ad hoc turbomachinery to ensure an adequate range of operation with high performance. A critical factor for supersonic turbines is to ensure the starting of the flow passages, which limits the flow turning and airfoil thickness. Radial outflow turbines inherently increase the cross section along the flow path, which holds great potential for high turning of supersonic flow with a low stage number and guarantees a compact design. First, the preliminary design space is described. Afterward a differential evolution multi-objective optimization with 12 geometrical design parameters is deducted. With the design tool autoblade 10.1, 768 geometries were generated and hub, shroud, and blade camber line were designed by means of Bezier curves. Outlet radius, passage height, and axial location of the outlet were design variables as well. Structured meshes with around 3.7 x 10(6) cells per passage were generated. Steady three-dimensional (3D) Reynolds-averaged Navier-Stokes (RANS) simulations, enclosed by the k-omega shear stress transport turbulence model were solved by the commercial solver CFD++. The geometry was optimized toward low entropy and high-power output. To prove the functionality of the new turbine concept and optimization, a full wheel unsteady RANS simulation of the optimized geometry exposed to a nozzled rotating detonation combustor (RDC) has been performed and the advantageous flow patterns of the optimization were also observed during transient operation., National Energy Technology Laboratory (Faculty Research Participation Program) (Funder ID: 10.13039/100013165). Spanish Ministry of Economy and Competitiveness (Grant No. TRA2016-7918-R). Universitat Politecnica de Valencia (Travel Grant). U.S. Department of Energy (Part-Time Faculty Appointment, Funder ID: 10.13039/100000015)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

On the impact of DPF downsizing and cellular geometry on filtration efficiency in pre- and post-turbine placement

  • Serrano, J.R.|||0000-0003-0692-3917
  • Bermúdez, Vicente|||0000-0002-2781-5598
  • Piqueras, P.|||0000-0002-3767-0839
  • Angiolini, Emanuele
[EN] the current work a computational study to evaluate the effect of the DPF downsizing on filtration efficiency is performed. The DPF is conventionally placed downstream of the turbine. However, its placement upstream of the turbine is growing in interest because of the benefits in specific fuel consumption, passive regeneration and aptitude to downsizing. Hence both pre- and post-turbine placement are considered in presence of clean and soot loaded substrates. An in-house 1D wall-flow DPF model for unsteady compressible flow is used. Volume reduction is approached considering diameter and length variation. In parallel, the cell density is also varied modifying the meso-geometry, i.e. cell size and porous wall thickness, imposing constant thermal integrity factor. The sensitivity to this last parameter is also analysed resulting its influence of second order in comparison to volume and cellular geometry effects. The lower Peclet number in the pre-turbine placement leads to higher filtration efficiency than post-turbine location comparing at the same DPF volume. Diameter based volume reduction provides slightly better results in filtration efficiency than length based reduction because of the way the filtration velocity field is varied. This general behaviour involves additional advantages to the potential for volume reduction of pre-turbine DPFs. Thus, different strategies with boundaries defined by volume reduction at constant filtration area or at constant specific filtration area can be approached looking for the best balance between fuel economy reduction and filtration efficiency increase provided by pre-turbine DPF placement., This work has been partially funded by FEDER and Government of Spain through Project No. TRA2016-79185-R. Additionally, the Ph.D. student E. Angiolini has been funded by a grant from Conselleria de Educacio, Cultura i Esport of the Generalitat Valenciana with reference GRISOLIA/2013/036. These supports are gratefully acknowledged by the authors.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Assessment of acoustic reciprocity and conservativeness in exhaust aftertreatment systems

  • Torregrosa, A. J.|||0000-0003-0933-1626
  • Piqueras, P.|||0000-0002-3767-0839
  • Sanchis, Enrique José|||0000-0002-6856-8992
  • Guilain, S.
  • Dubarry, M.
[EN] Tightening emission standards limiting gas and aerosol emissions from internal combustion engines have led to the extensive use of exhaust aftertreatment systems (EATS) with different chemical functions as a solution to meet standards requirements. Incidentally, the placement of aftertreatment monolithic devices into the exhaust line also plays a key role on the exhaust noise emission. Their presence disturbs the pattern of the pressure waves and sets the boundary conditions for the silencer design. The impact of the EATS on wave transmission can be analyzed by means of the transmission or scattering matrix. The present work discusses the implications of acoustic reciprocity and conservativeness on the definition of the scattering matrix elements. The fulfillment of these properties in real operating conditions was evaluated against a set of experimental data obtained for several exhaust aftertreatment monolithic bricks in an impulse test rig. The influence of different excitation amplitudes and superimposed mean flows was also considered. Once it was shown that the devices are reciprocal, the need to account for dissipation phenomena was evidenced. Finally, the application of reciprocity and conservativeness together with dissipation provided simple expressions allowing to predict the response of the EATS in the inverse direction, i.e. from outlet to inlet, from the transmission and reflection properties obtained in the direct direction. Thus, the proposed procedure becomes useful to reduce both the required number of tests and the gas dynamics modelling work in methodologies driven to assess the acoustic response of EATS based on the use of experimental and computational tools. (C) 2018 Elsevier Ltd. All rights reserved., This research has been partially supported by FEDER and the Government of Spain through project TRA2016-79185-R. Additionally, the Ph.D. student Enrique José Sanchis has been funded by a grant from Universitat Politècnica de València with reference FPI-2016-S2-1355.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Contribution to Tip Leakage Loss Modeling in Radial Turbines Based on 3D Flow Analysis and 1D Characterization

  • Serrano, J.R.|||0000-0003-0692-3917
  • Navarro, Roberto|||0000-0003-2587-4954
  • García-Cuevas González, Luis Miguel|||0000-0001-9340-0617
  • Inhestern, Lukas Benjamin
[EN] The characterization of tip leakage flow plays an important role for one-dimesional loss modeling and design in radial turbine research. Tip leakage losses can be expressed as function of fluid momentum and mass flow passing through the tip gap. Friction-driven flow and contrariwise oriented pressure gradient-driven flow are highly coupled. However, these numbers are mostly unknown and dependent on tip gap geometry and turbine running condition. Based on a commonly used definition of a non-dimensional tip leakage momentum ratio, a novel correlation has been derived. This allows a consistent characterization for variable tip gap sizes over a wide range of operating conditions. The correlation has been validated by means of CFD data with high variety in reduced speed tip gap geometry and expansion ratios. Results of the novel number show significant improvements of quantitative and qualitative results over a wide range of running conditions in comparison to existing correlations. Furthermore, correlations for tip leakage velocities, that can easily be used in one-dimensional models, have been derived. Finally, it has been demonstrated, that the influence of inlet flow momentum on the tip leakage flow can be analyzed with presented correlations., The work has been partially supported by FEDER and the Spanish Ministry of Economy and Competitiveness through grant number TRA2016-79185-R. The authors would also like to acknowledge the Research and Development Aid Program PAID-01-16 of the Universitat Politecnica de Valencia, Spain.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

On the Impact of Particulate Matter Distribution on Pressure Drop of Wall-Flow Particulate Filters

  • Bermúdez, Vicente|||0000-0002-2781-5598
  • Serrano, J.R.|||0000-0003-0692-3917
  • Piqueras, P.|||0000-0002-3767-0839
  • Sanchis, Enrique José|||0000-0002-6856-8992
[EN] Wall-flow particulate filters are a required exhaust aftertreatment system to abate particulate matter emissions and meet current and incoming regulations applying worldwide to new generations of diesel and gasoline internal combustion engines. Despite the high filtration efficiency covering the whole range of emitted particle sizes, the porous substrate constitutes a flow restriction especially relevant as particulate matter, both soot and ash, is collected. The dependence of the resulting pressure drop, and hence the fuel consumption penalty, on the particulate matter distribution along the inlet channels is discussed in this paper taking as reference experimental data obtained in water injection tests before the particulate filter. This technique is demonstrated to reduce the particulate filter pressure drop without negative effects on filtration performance. In order to justify these experimental data, the characteristics of the particulate layer are diagnosed applying modeling techniques. Different soot mass distributions along the inlet channels are analyzed combined with porosity change to assess the new properties after water injection. Their influence on the subsequent soot loading process and regeneration is assessed. The results evidence the main mechanisms of the water injection at the filter inlet to reduce pressure drop and boost the interest for control strategies able to force the re-entrainment of most of the particulate matter towards the inlet channels' end., This work has been partially supported by the Spanish Ministry of Economy and Competitiveness through Grant No. TRA2016-79185-R. Additionally, the Ph.D. student Enrique Jose Sanchis has been funded by a grant from Universitat Politecnica de Valencia with the reference FPI-2016-S2-1355.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Computational Methodology for Knocking Combustion Analysis in Compression-Ignited Advanced Concepts

  • Serrano, J.R.|||0000-0003-0692-3917
  • Novella Rosa, Ricardo|||0000-0002-5123-6924
  • Gómez-Soriano, Josep|||0000-0002-2742-9224
  • Martínez-Hernándiz, Pablo José
[EN] In the present work, a numerical methodology based on three-dimensional (3D) computational fluid dynamics (CFD) was developed to predict knock in a 2-Stroke engine operating with gasoline Partially Premixed Combustion (PPC) concept. Single-cycle Unsteady Reynolds-Averaged Navier Stokes (URANS) simulations using the renormalization group (RNG) k - epsilon model were performed in parallel while the initial conditions are accordingly perturbed in order to imitate the variability in the in-cylinder conditions due to engine operation. Results showed a good agreement between experiment and CFD simulation with respect to cycle-averaged and deviation of the ignition timing, combustion phasing, peak pressure magnitude and location. Moreover, the numerical method was also demonstrated to be capable of predicting knock features, such as maximum pressure rise rate and knock intensity, with good accuracy. Finally, the CFD solution allowed to give more insight about in-cylinder processes that lead to the knocking combustion and its subsequent effects., The work has been partially supported by the Spanish Ministerio de Economia y Competitividad through grant number TRA2016-79185-R. The equipment used in this work has been partially supported by FEDER project funds "Dotacion de infraestructuras cientifico tecnicas para el Centro Integral de Mejora Energetica y Medioambiental de Sistemas de Transporte (CiMeT), (FEDER-ICTS-2012-06)" from the operational program of unique scientific and technical infrastructure of the Spanish Ministerio de Economia y Competitividad. In addition, J. Gomez-Soriano is partially supported by an FPI contract (FPI-S2-2016-1353) of the "Programa de Apoyo para la Investigacion y Desarrollo (PAID-01-16)" of the Universitat Politecnica de Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Influence of the cell geometry on the conversion efficiency of oxidation catalysts under real driving conditions

  • Piqueras, P.|||0000-0002-3767-0839
  • Ruiz, María José
  • Martín Herreros, José
  • Tsolakis, Athanasios
[EN] Worldwide pollutant regulations applied to the transportation sector are progressively tightening the emission limits and widening the operating conditions of the type approval tests. As a result, the layout and thermal management of the exhaust system is becoming highly complex looking to achieve early catalytic converter activation. On this regard, the monolith meso-geometry plays a primary role to optimise the pollutants con -version efficiency. The geometrical characteristics simultaneously affect and trade-off multiple flow phenomena as the exhaust gas is transported through the channels. These include the bulk gas and internal pore diffusion towards the active sites in addition to the heat transfer including convection, radial conductivity and thermal capacitance. In this work, the impacts of the cell size, cross-section shape, washcoat loading and substrate material on CO and HC conversion efficiency have been investigated under representative real driving condi-tions. From the real driving conditions experimental data, the study decouples the influence of the washcoat loading from the cell size and material applying a catalytic converter model. Detailed expressions are provided for the calculation of the specific surfaces and heat and mass transfer parameters as a function of the cell and washcoat meso-geometry in square and triangular cells. Therefore, this work enables to identify the processes which govern the catalytic abatement of pollutant emissions. In particular, the role of the gas and washcoat specific surfaces is highlighted because of its importance on the optimization of the mass transfer process by means of a proper cell geometry selection. In parallel, the differences in the change of the CO and HC abatement patterns, which are explained by the characteristic CO emission spikes in accelerations and the HC accumulation, contribute to evidence the limitations on the conversion efficiency benefit that the optimum cell geometry and washcoat loading can provide., The authors acknowledge FEDER and Spanish Ministerio de Economia y Competitividad for partially supporting this research through project TRA2016-79185-R. Additionally, the Ph.D. student Maria Jose Ruiz has been funded by a grant from Universitat Politecnica de Valencia with reference number FPI-2018-S2-10.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Influence of Pre-Turbine Small-Sized Oxidation Catalyst on Engine Performance and Emissions under Driving Conditions

  • Serrano, J.R.|||0000-0003-0692-3917
  • Piqueras, P.|||0000-0002-3767-0839
  • De La Morena, Joaquín|||0000-0003-0208-508X
  • Ruiz-Lucas, María José
[EN] The earlier activation of the catalytic converters in internal combustion engines is becoming highly challenging due to the reduction in exhaust gas temperature caused by the application of CO2 reduction technologies. In this context, the use of pre-turbine catalysts arises as a potential way to increase the conversion efficiency of the exhaust aftertreatment system. In this work, a small-sized oxidation catalyst consisting of a honeycomb thin-wall metallic substrate was placed upstream of the turbine to benefit from the higher temperature and pressure prior to the turbine expansion. The change in engine performance and emissions in comparison to the baseline configuration are analyzed under driving conditions. As an individual element, the pre-turbine catalyst contributed positively with a relevant increase in the overall CO and HC conversion efficiency. However, its placement produced secondary effects on the engine and baseline aftertreatment response. Although small-sized monoliths are advantageous to minimize the thermal inertia impact on the turbocharger lag, the catalyst cross-section is in trade-off with the additional pressure drop that the monolith causes. As a result, the higher exhaust manifold pressure in pre-turbine pre-catalyst configuration caused a fuel consumption increase higher than 3% while the engine-out CO and HC emissions did around 50%. These increments were not completely offset despite the high pre-turbine pre-catalyst conversion efficiency (>40%) because the partial abatement of the emissions in this device conditioned the performance of the close-coupled oxidation catalyst., This research has been partially supported by FEDER and the Government of Spain through project TRA2016-79185-R and by Universitat Politecnica de Valencia under a grant with reference number FPI-2018-S2-10 to the Ph.D. student Maria Jose Ruiz.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

A methodology to study oil-coking problem in small turbochargers

  • Serrano, J.R.|||0000-0003-0692-3917
  • Tiseira, Andrés-Omar|||0000-0001-9472-2386
  • García-Cuevas González, Luis Miguel|||0000-0001-9340-0617
  • Rodriguez-Usaquen, Yuly Tatiana
  • Guillaume, Mijotte
[EN] In compliance with oncoming emission directives, turbocharging and increasing complexity in the turbocharger system demands a great effort from researchers on the development of effective procedures and tools to cope with the new technological exigencies. This article describes a methodology for studying oil-coking influence in turbocharger performance. A preliminary evaluation and calibration is done. The aim of this work focuses on the development of methodologies and tools that help to evaluate and understand the consequences that degraded oils can generate in the bearing system during enhanced oil-coking procedure. Several experimental tests have been carried out in an engine test bench and using an independent lubrication system that only feeds the turbocharger. The test campaign is done under a specific engine cycle and using oil artificially contaminated at two different levels. The work is divided into two parts. The first part provides a description and definition of test conditions for measuring of the maximum temperature in the bearing system and the second part tackles the measurement and post-processing of the main instantaneous parameters defining the engine and turbocharger behavior., The authors would like to acknowledge the Apoyo para la investigación y Desarrollo (PAID) grant for doctoral studies (FPI-2016-S2-1354). This work was partially supported by FEDER and the Spanish Ministry of Economy and Competitiveness through Grant Number TRA2016-79185-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Impact on Reduction of Pollutant Emissions from Passenger Cars when Replacing Euro 4 with Euro 6d Diesel Engines Considering the Altitude Influence

  • Serrano, J.R.|||0000-0003-0692-3917
  • Piqueras, P.|||0000-0002-3767-0839
  • Abbad Andaloussi, Ali
  • Tabet, Roberto
  • Bender, Stefan
  • Gómez-Gil, Javier
[EN] The impact of Euro 4 compression ignition engines over the air quality in Europe has been analyzed in this work by comparing them with Euro 6d emissions regulation. The Euro 6d diesel engine has been chosen as the preferred replacement according to its advantages in global warming potential (GWP) emissions, like methane hydrocarbons (MHC) and CO2, with respect to Euro 6d petrol-based powertrains. The motivation for this study is that the effects of the emissions reduction policies, as the implementation of the regulation Euro 6d, are necessarily limited due to the great number of passenger cars still in circulation that were homologated under Euro 4 or older standards. To address the impact of the old vehicle pool, a Worldwide harmonized Light-vehicles Test Cycle (WLTC) has been used to analyze the performance and pollutant emissions of a Euro 4 diesel engine in altitude conditions. This driving cycle and engine are considered as a baseline for the subsequent discussion, where the altitude plays a key role because of the European geography. It forces passenger cars to drive over sea level during a significant number of trips. Thus, an analysis of how significant would be the impact of energy policies promoting the substitution of the pre-Euro 5 diesel fleet (>10 years old) by modern Euro 6d engines in the short term on the pollutants and GWP emissions reduction is presented., This research has been partially supported by FEDER and the Government of Spain through project TRA2016-79185-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Tesis de maestría (MasterThesis)

Análisis comparado de las emisiones de los motores E4 en altura

  • Tabet Aleixandre, Roberto
[ES] El funcionamiento de los motores de combustión en altura no ha sido tradicionalmente bien estudiado desde el punto de vista del análisis de sus emisiones. La posibilidad de disponer de un simulador de altura en laboratorios a cualquier cota permite realizar estos estudios en detalle. En el presente TFM se ha usado un simulador de altura comercialmente conocido como MEDAS (multifunctional efficient and dynamic altitude simulator) y desarrolado en el I.U. CMT-Motores Térmicos para su comercialización por la multinacional Horiba. MEDAS se ha validado previamente en una cámara altimétrica comparando los resultados de emisiones en estacionario de un motor comercial con la cámara altimétrica y con el simulador de altura (MEDAS). A continuación, se ha hecho un estudio usando el ciclo transitorio WLTC (World Harmonized Light Duty Transient Cycle) para comparar la emisiones de un motor E4 en altura con las que establece la norma actual de los motores Diesel E6d. Se ha concluido que el reemplazo de los motores E4 por E6d supondría una disminución importante de las emisiones contaminantes. En el análisis se ha discriminado entre la operación a nivel del mar en un tráfico como el de Barcelona y la operación en altura en una ciudad como Madrid. También se han analizado las operaciones a 2000m y 3000m de altura, que aunque no hay centros de población importantes a esas alturas en Europa, sí los hay en otras areas geográficas como Sudamerica o Asia., [EN] The operation of combustion engines in height has not traditionally been well studied from the point of view of the analysis of their emissions. The possibility of having a height simulator in laboratories at any altitude level allows these studies to be carried out in detail. In the present TFM, a height simulator commercially known as MEDAS (multifunctional efficient and dynamic altitude simulator) has been used and developed in the I.U. CMT-Motores Térmicos for its commercialisation by the multinational Horiba. MEDAS has been previously validated in a hypobaric chamber comparing the results of stationary emissions of a commercial engine with the altimeter camera and with the height simulator (MEDAS). Next, a study has been made using the transient cycle WLTC (World Harmonised Light Duty Transient Cycle) to compare the emissions of an E4 engine in height with those established by the current standard of the E6d Diesel engines. It has been concluded that the replacement of the E4 engines by E6d would imply a significant reduction of the polluting emissions. The analysis has discriminated between the operation at sea level in a traffic like at Barcelona and the operation at height in a city like Madrid. The operations at 2000m and 3000m have also been analysed, although there are no important population areas at this heights in Europe, although there are other geographical areas such as South America or Asia., This work was partially funded by FEDER and Government of Spain through Project TRA2016-79185-R
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Internal pore diffusion and adsorption impact on the soot oxidation in wall-flow particulate filters

  • Macian Martinez, Vicente
  • Serrano, J.R.|||0000-0003-0692-3917
  • Piqueras, P.|||0000-0002-3767-0839
  • Sanchis, Enrique José|||0000-0002-6856-8992
[EN] The automotive industry is driven its efforts to cleaner internal combustion engines. As a result, the engine has become conditioned by the exhaust aftertreatment systems. The regeneration of wall-flow particulate filters (PFs) evidences such an interaction. The PFs prevent the soot emission whereas, as a counterpart, the fuel consumption increases. Consequently, passive and active regeneration strategies are needed to clean the filter back and limit the penalty in CO2. In this context, modelling tools play a key role to achieve a comprehensive understanding and control of the regeneration. In this work, a regeneration model coupled to a one-dimensional compressible unsteady flow solver for PFs is presented. The importance of the main physical and chemical steps related to the soot oxidation is discussed. The influence of the diffusion of gaseous reactants inside the primary soot particles is firstly addressed. The inclusion of this step into the definition of the reaction rate provides temperature dependence to the soot specific surface. Next, the reactants adsorption is analysed. This step leads to define a surface coverage, which behave as an equivalent reaction order. It allows figuring out the influence of the gaseous reactants concentration on the reaction rate and its dependence with the temperature. (C) 2019 Elsevier Ltd. All rights reserved., This research has been partially supported by FEDER and the Government of Spain through project TRA2016-79185-R. Additionally, the Ph.D. student Enrique José Sanchis has been funded by a grant from Universitat Politècnica de València with reference FPI-2016-S2-1355.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Analysis of Passenger Car Turbocharged Diesel Engines Performance When Tested at Altitude and of the Altitude Simulator Device Used

  • Broatch, A.|||0000-0001-9991-1039
  • Bermúdez, Vicente|||0000-0002-2781-5598
  • Serrano, J.R.|||0000-0003-0692-3917
  • Tabet, Roberto
  • Gómez, Javier
  • Bender, Stefan
[EN] According to current worldwide trends for homologation vehicles in real driving conditions is forced to test the engines in altitude and in highly dynamic driving cycles in order to approach nowadays and next future emissions standard. Up to now, there were two main options to perform this type of tests: round-robin tests of the whole vehicle or hypobaric chambers, both with high costs and low repeatability. In this paper a new device is described, which can emulate ambient conditions at whatever altitude between sea level and 5000m high. Even it can be used to emulate ambient conditions at sea level when test bench is placed up to 2000m high. The main advantages of the altitude simulation equipment are as follows: dynamic emulation of all the psychrometric variables affecting the vehicles during round-robin tests; lower space usage and low-energy consumption. The altitude simulator (AS) has been validated comparing with results from a hypobaric chamber at different altitudes. Previously a research about the dispersion in the measurements of both testing devices has been done for assessing the results of the comparison experiment. Final conclusion resulted in the same operating performance and emissions of the studied engine with both types of testing equipment for altitude simulation., FEDER, Government of Spain through Project TRA2016-79185-R (Funder ID: 10.13039/501100002924).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Analysis of the Driving Altitude and Ambient Temperature Impact on the Conversion Efficiency of Oxidation Catalysts

  • Serrano, J.R.|||0000-0003-0692-3917
  • Piqueras, P.|||0000-0002-3767-0839
  • Sanchis, Enrique José|||0000-0002-6856-8992
  • Diesel Costa, Bárbara
[EN] Worldwide emission standards are extending their requirements to cover engine operation under extreme ambient conditions and fill the gap between the type-approval and real driving conditions. The new ambient boundaries affect the engine performance and raw emissions as well as the efficiency of the exhaust aftertreatment systems. This study evaluates the impact of high altitude and low ambient temperature on the light-off temperature and conversion efficiency of an oxidation catalyst. The results are compared in a common range of exhaust mass flow and temperature with the baseline sea-level operation at 20 degrees C. A reduction of CO and HC conversion efficiencies was found at 2500 m and -7 degrees C, with a relevant increase of the light-off temperature for both of the pollutants. The analysis of the experimental data was complemented with the use of a catalyst model to identify the causes leading to the deterioration of the CO and HC light-off. The use of the model allowed for identifying, for the same exhaust mass flow and temperature, the contributions to the variation of conversion efficiency caused by the change in engine-out emissions and tailpipe pressure, which are, in turn, manifested in the variation of the reactants partial pressure and dwell time as governing parameters., This research has been partially supported by FEDER and the Government of Spain through project TRA2016-79185-R. Additionally, the PhD candidate Barbara Diesel has been funded by a grant from the Government of Generalitat Valenciana and FSE (European Union) with reference ACIF/2018/109.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Evaluating the oxidation kinetic parameters of gasoline direct injection soot from thermogravimetric analysis experiments

  • Piqueras, P.|||0000-0002-3767-0839
  • Sanchis, Enrique José|||0000-0002-6856-8992
  • Herreros, J.M.
  • Tsolakis, A.
[EN] The abatement of particulate matter in gasoline direct injection (GDI) engines requires the use of particulate filters. In turn, the optimisation of their regeneration is based on a deep knowledge of the soot oxidation behaviour. The determination of the intrinsic kinetic parameters of GDI soot is explored based on thermogravimetric analysis (TGA) and reaction rate modelling. New understanding on the oxidation of GDI soot is provided enabling an accurate prediction in a wide range of temperature and O-2 concentration. Firstly, the dependence of the soot reaction order on the boundary conditions is discussed. The analysis of the Arrhenius equation parameters reveals variable O-2 reaction order. It leads to consider the effect of mass transfer and adsorption (Langmuir and Dubinin-Radushkevich isotherms) as reaction rate limiters. Combined with the soot reaction order approach, the prediction ability of the proposed model is assessed in an extended range of isothermal and non-isothermal TGA experiments., This research has been partially supported by FEDER and the Government of Spain through project TRA2016-79185-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Experimental approach for the characterization and performance analysis of twin entry radial-inflow turbines in a gas stand and with different flow admission conditions

  • Serrano, J.R.|||0000-0003-0692-3917
  • Arnau Martínez, Francisco José|||0000-0003-2902-0630
  • García-Cuevas González, Luis Miguel|||0000-0001-9340-0617
  • Samala, Vishnu
  • Smith, Les
[EN] In an internal combustion engine, twin entry turbine operates under different unequal admission conditions by feeding the turbine with a dissimilar amount of flow in each entry for a majority of the time. Despite of the impact on turbine performance, normal characteristic maps of these turbines are usually available only for full admission conditions. The current study investigates the best way of building characteristic maps of twin entry radial inflow turbines working under different admission conditions. The mass flow conditions are varied independently for each entry and results are examined to characterize the turbine performance parameters. The new methodology provides a practical approach regarding the reduced turbine speed; mass flow ratio; pressure ratios and efficiencies of a twin entry turbine. The most important conclusion of this work is the protocol of data analysis itself, which allows systematizing the testing procedure of this type of turbines with different steady flow admission and in quasi-adiabatic conditions. By sorting the experimental data in an orderly manner through proposed analysis, the readers can get benefit of this procedure to calibrate their own quasi-steady models for both: mass flow rate and efficiency; or to build new quasi-steady models with clear merit functions for fitting., Vishnu Samala is partially supported through contract FPI-2017-S2-1256 of Programa de Apoyo para la Investigacion y Desarrollo (PAID) of Universitat Politecnica de Valencia. This work was partially funded by FEDER and Government of Spain through Project TRA2016-79185-R. The authors wish to thank M.A. Ortiz and R. Carrascosa for their invaluable work during the experimental setup and campaign.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Performance of a diesel oxidation catalyst under diesel-gasoline reactivity controlled compression ignition combustion conditions

  • Piqueras, P.|||0000-0002-3767-0839
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Ruiz, María José
[EN] Reactivity controlled compression ignition is a promising combustion strategy due to the combination of excellent thermal efficiency with ultra-low nitrogen oxides and particulate matter raw emissions. However, very high levels of unburned hydrocarbons and carbon monoxide emissions are found. It limits the reactivity controlled compression ignition use at very low loads and presents an additional challenge for the diesel oxidation catalyst. The low exhaust temperature and high carbon monoxide and hydrocarbon concentration can penalise the catalyst conversion efficiency. The objective of this work is to evaluate the response of an automotive diesel oxidation catalyst when used for reactivity controlled compression ignition combustion combining experimental and modelling approaches. For this purpose, dedicated tests have been done using diesel-gasoline as fuel combination in a single-cylinder engine. This way, the catalyst conversion efficiency has been determined within a wide operating range covering hydrocarbon adsorption conditions and the pollutants abatement dependence on the mass flow and temperature. The experimental results in the full-size catalyst has been analysed by modelling. A lumped diesel oxidation catalyst model has been applied to extend the results to multi-cylinder engine conditions and to determine the light-off curves for both carbon monoxide and hydrocarbons. These tests evidence the penalty in light-off temperature due to high pollutants mass fraction, which promotes inhibition limitations to the reaction rate., This research has been partially supported by FEDER and the Government of Spain through project TRA2016-79185-R. Additionally, the Ph.D. student Maria Jose Ruiz has been funded by a grant from Universitat Politecnica de Valencia with reference number FPI-2018S2-10.