Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 4
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Sensitivity of pollutants abatement in oxidation catalysts to the use of alternative fuels

  • Piqueras, P.|||0000-0002-3767-0839
  • Ruiz-Lucas, María José
  • Martin Herreros, Jose
  • Tsolakis, Athanasios
[EN] The aim to reduce well to wheel emissions incentives the utilisation of alternative fuels (low to zero carbon content and/or low well to tank emissions) as well as the enhancement of engine efficiency. In parallel, the reduction of engine tailpipe emissions brings new challenges such as the decrease of the exhaust gas temperature. This trend penalises the ability of the exhaust aftertreatment system to eliminate pollutant emissions. In addition, the combustion of alternative fuels and new combustion modes induce changes in the nature and concentration of the exhaust species, which is known to affect the pollutants abatement mechanisms. This investigation provides new understanding on the sensitivity of pollutants abatement in oxidation catalysts to the use of alternative fuels. The studied fuels are conventional diesel, alternative fuels (rapeseed methyl ester and gas to liquid) as well as propane using a dual-fuel combustion strategy. The research combines experimental conversion efficiency from genuine exhaust gases with modelling work useful to explain the reasons for the change in light-off temperature as a function of the fuel. In addition to the CO and NO impact, HC surrogates are proposed distinguishing species of different reactivity for each fuel based on the experimental HC speciation. The results highlight the role of the engine-out emissions on the pollutants conversion efficiency. Their fashion with different fuels contributes to evidence the interest for low engine-out emissions along with low light alkanes content in total HC, as promoted by alternative fuels, to reduce the oxidation light-off temperature., This research has been partially supported by FEDER and the Government of Spain through project TRA2016-79185-R and by Universitat Politecnica de Valencia under a grant with reference number FPI-2018-S2-10 to the Ph.D. student Maria Jose Ruiz
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Influence of the cell geometry on the conversion efficiency of oxidation catalysts under real driving conditions

  • Piqueras, P.|||0000-0002-3767-0839
  • Ruiz, María José
  • Martín Herreros, José
  • Tsolakis, Athanasios
[EN] Worldwide pollutant regulations applied to the transportation sector are progressively tightening the emission limits and widening the operating conditions of the type approval tests. As a result, the layout and thermal management of the exhaust system is becoming highly complex looking to achieve early catalytic converter activation. On this regard, the monolith meso-geometry plays a primary role to optimise the pollutants con -version efficiency. The geometrical characteristics simultaneously affect and trade-off multiple flow phenomena as the exhaust gas is transported through the channels. These include the bulk gas and internal pore diffusion towards the active sites in addition to the heat transfer including convection, radial conductivity and thermal capacitance. In this work, the impacts of the cell size, cross-section shape, washcoat loading and substrate material on CO and HC conversion efficiency have been investigated under representative real driving condi-tions. From the real driving conditions experimental data, the study decouples the influence of the washcoat loading from the cell size and material applying a catalytic converter model. Detailed expressions are provided for the calculation of the specific surfaces and heat and mass transfer parameters as a function of the cell and washcoat meso-geometry in square and triangular cells. Therefore, this work enables to identify the processes which govern the catalytic abatement of pollutant emissions. In particular, the role of the gas and washcoat specific surfaces is highlighted because of its importance on the optimization of the mass transfer process by means of a proper cell geometry selection. In parallel, the differences in the change of the CO and HC abatement patterns, which are explained by the characteristic CO emission spikes in accelerations and the HC accumulation, contribute to evidence the limitations on the conversion efficiency benefit that the optimum cell geometry and washcoat loading can provide., The authors acknowledge FEDER and Spanish Ministerio de Economia y Competitividad for partially supporting this research through project TRA2016-79185-R. Additionally, the Ph.D. student Maria Jose Ruiz has been funded by a grant from Universitat Politecnica de Valencia with reference number FPI-2018-S2-10.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Influence of Pre-Turbine Small-Sized Oxidation Catalyst on Engine Performance and Emissions under Driving Conditions

  • Serrano, J.R.|||0000-0003-0692-3917
  • Piqueras, P.|||0000-0002-3767-0839
  • De La Morena, Joaquín|||0000-0003-0208-508X
  • Ruiz-Lucas, María José
[EN] The earlier activation of the catalytic converters in internal combustion engines is becoming highly challenging due to the reduction in exhaust gas temperature caused by the application of CO2 reduction technologies. In this context, the use of pre-turbine catalysts arises as a potential way to increase the conversion efficiency of the exhaust aftertreatment system. In this work, a small-sized oxidation catalyst consisting of a honeycomb thin-wall metallic substrate was placed upstream of the turbine to benefit from the higher temperature and pressure prior to the turbine expansion. The change in engine performance and emissions in comparison to the baseline configuration are analyzed under driving conditions. As an individual element, the pre-turbine catalyst contributed positively with a relevant increase in the overall CO and HC conversion efficiency. However, its placement produced secondary effects on the engine and baseline aftertreatment response. Although small-sized monoliths are advantageous to minimize the thermal inertia impact on the turbocharger lag, the catalyst cross-section is in trade-off with the additional pressure drop that the monolith causes. As a result, the higher exhaust manifold pressure in pre-turbine pre-catalyst configuration caused a fuel consumption increase higher than 3% while the engine-out CO and HC emissions did around 50%. These increments were not completely offset despite the high pre-turbine pre-catalyst conversion efficiency (>40%) because the partial abatement of the emissions in this device conditioned the performance of the close-coupled oxidation catalyst., This research has been partially supported by FEDER and the Government of Spain through project TRA2016-79185-R and by Universitat Politecnica de Valencia under a grant with reference number FPI-2018-S2-10 to the Ph.D. student Maria Jose Ruiz.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Performance of a diesel oxidation catalyst under diesel-gasoline reactivity controlled compression ignition combustion conditions

  • Piqueras, P.|||0000-0002-3767-0839
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Ruiz, María José
[EN] Reactivity controlled compression ignition is a promising combustion strategy due to the combination of excellent thermal efficiency with ultra-low nitrogen oxides and particulate matter raw emissions. However, very high levels of unburned hydrocarbons and carbon monoxide emissions are found. It limits the reactivity controlled compression ignition use at very low loads and presents an additional challenge for the diesel oxidation catalyst. The low exhaust temperature and high carbon monoxide and hydrocarbon concentration can penalise the catalyst conversion efficiency. The objective of this work is to evaluate the response of an automotive diesel oxidation catalyst when used for reactivity controlled compression ignition combustion combining experimental and modelling approaches. For this purpose, dedicated tests have been done using diesel-gasoline as fuel combination in a single-cylinder engine. This way, the catalyst conversion efficiency has been determined within a wide operating range covering hydrocarbon adsorption conditions and the pollutants abatement dependence on the mass flow and temperature. The experimental results in the full-size catalyst has been analysed by modelling. A lumped diesel oxidation catalyst model has been applied to extend the results to multi-cylinder engine conditions and to determine the light-off curves for both carbon monoxide and hydrocarbons. These tests evidence the penalty in light-off temperature due to high pollutants mass fraction, which promotes inhibition limitations to the reaction rate., This research has been partially supported by FEDER and the Government of Spain through project TRA2016-79185-R. Additionally, the Ph.D. student Maria Jose Ruiz has been funded by a grant from Universitat Politecnica de Valencia with reference number FPI-2018S2-10.