Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 2
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Testing of battery separators: transducers and methods for air-coupled ultrasonic sensing

  • Patricia Salso
  • Vicente Genovés
  • Tomás Gómez Álvarez-Arenas
Battery separator me3mbranes are thin polymeric microporous films placed between battery electrodes. They are a key component that strongly affects both battery performance and security and controlling its main properties is critical for the industry. In particular, the manufacturing process demands tests that allow checking both the mechanical integrity (porosity, thickness, pore size, etc.) of the materials and the consistency of these properties during the construction of the batteries. The use of an air-coupled ultrasonic system is proposed in this work. It is expected that this will make possible the non-destructive and quick testing of these materials, in order to evaluate thickness, stiffness, pore distribution and pore size of the separator. By means of three pairs of transducers, the modulus and phase of the transmission coefficient was measured from 0.35 to 1.4 MHz in different materials. The measurements show a clear modification of the film response produced by the presence of porosity. This suggests that the transmission of ultrasonic waves in battery separators using air-coupled ultrasound may have two contributions: one corresponds to the propagation though the solid part, the other corresponds to propagation in the pores. The former allows to determine properties like film thickness and elastic constants, while the latter allows to determine porosity and pore size and pore tortuosity. This work set the basis for the development of a quality test for the in-line inspection of these materials during their fabrication. The observed ultrasonic response in microporous separators suggest the possibility to use low frequency air-coupled transducers with limited sensitivity, where the use of MEM transducers at industrial scale can be advantageous, m project Listen2Future. Under grant 101096884, Listen2Future is co-funded by the European Union and by the Project Ref. PCI2022-135060-2 funded by CIN/AEI/10.13039/501100011033 and by EU “NextGenerationEU”/PRTR., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

High frequency venting of MEMS ultrasonic transducers and sensors: materials solutions

  • Gómez Álvarez-Arenas, Tomás
  • Salso, P.
  • Genovés, V.
. This paper introduces the concept of ultrasonic venting. Similar to acoustic vents, ultrasonic vents refer to the aperture in air-coupled MEMS ultrasonic transducers (either PMUT or CMUT) intended to allow the equalization of internal and external pressures, the transfer of heat and the pass of ultrasonic waves, while impeding the penetration of fluids or particles that can affect the transducer membrane. To that end, vents are covered with a porous membrane whose properties are tuned to meet the afore mentioned requirements. The main difficulty in ultrasonic venting, compared with acoustic venting, is that the required “transparency” to ultrasonic waves is much more difficult to achieve. This involves two main problems as both transmission loss and frequency distortion are much larger at ultrasonic frequencies than in the audio range. The objectives of this paper are: to measure the response of acoustic venting materials in the ultrasonic frequency range, to determine the usability of these materials in ultrasonic vents, and to extract useful information for the design of efficient ultrasonic venting materials. Transmission coefficient spectra of different acoustic venting materials is measured in the frequency range 0.2 – 2.7 MHz. The origin of the ultrasonic losses and frequency distortion are analysed as well as the role of mode conversion, internal interferences, modes interference, etc. Results reveal that none of the acoustic venting materials analysed can be used in ultrasonic venting applications, but the obtained knowledge about the response of these materials in the ultrasonic frequency range permit to advance in the selection of successful candidate materials for this application., Project Listen2Future funding is acknowledged. Under grant 101096884, Listen2Future is co-funded by the EU and by the Project Ref. PCI2022-135060-2 funded by CIN/AEI/10.13039/501100011033 and by EU “Next Generation EU”/PRTR, Peer reviewed