Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 4
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Testing of battery separators: transducers and methods for air-coupled ultrasonic sensing

  • Patricia Salso
  • Vicente Genovés
  • Tomás Gómez Álvarez-Arenas
Battery separator me3mbranes are thin polymeric microporous films placed between battery electrodes. They are a key component that strongly affects both battery performance and security and controlling its main properties is critical for the industry. In particular, the manufacturing process demands tests that allow checking both the mechanical integrity (porosity, thickness, pore size, etc.) of the materials and the consistency of these properties during the construction of the batteries. The use of an air-coupled ultrasonic system is proposed in this work. It is expected that this will make possible the non-destructive and quick testing of these materials, in order to evaluate thickness, stiffness, pore distribution and pore size of the separator. By means of three pairs of transducers, the modulus and phase of the transmission coefficient was measured from 0.35 to 1.4 MHz in different materials. The measurements show a clear modification of the film response produced by the presence of porosity. This suggests that the transmission of ultrasonic waves in battery separators using air-coupled ultrasound may have two contributions: one corresponds to the propagation though the solid part, the other corresponds to propagation in the pores. The former allows to determine properties like film thickness and elastic constants, while the latter allows to determine porosity and pore size and pore tortuosity. This work set the basis for the development of a quality test for the in-line inspection of these materials during their fabrication. The observed ultrasonic response in microporous separators suggest the possibility to use low frequency air-coupled transducers with limited sensitivity, where the use of MEM transducers at industrial scale can be advantageous, m project Listen2Future. Under grant 101096884, Listen2Future is co-funded by the European Union and by the Project Ref. PCI2022-135060-2 funded by CIN/AEI/10.13039/501100011033 and by EU “NextGenerationEU”/PRTR., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

High frequency venting of MEMS ultrasonic transducers and sensors: materials solutions

  • Gómez Álvarez-Arenas, Tomás
  • Salso, P.
  • Genovés, V.
. This paper introduces the concept of ultrasonic venting. Similar to acoustic vents, ultrasonic vents refer to the aperture in air-coupled MEMS ultrasonic transducers (either PMUT or CMUT) intended to allow the equalization of internal and external pressures, the transfer of heat and the pass of ultrasonic waves, while impeding the penetration of fluids or particles that can affect the transducer membrane. To that end, vents are covered with a porous membrane whose properties are tuned to meet the afore mentioned requirements. The main difficulty in ultrasonic venting, compared with acoustic venting, is that the required “transparency” to ultrasonic waves is much more difficult to achieve. This involves two main problems as both transmission loss and frequency distortion are much larger at ultrasonic frequencies than in the audio range. The objectives of this paper are: to measure the response of acoustic venting materials in the ultrasonic frequency range, to determine the usability of these materials in ultrasonic vents, and to extract useful information for the design of efficient ultrasonic venting materials. Transmission coefficient spectra of different acoustic venting materials is measured in the frequency range 0.2 – 2.7 MHz. The origin of the ultrasonic losses and frequency distortion are analysed as well as the role of mode conversion, internal interferences, modes interference, etc. Results reveal that none of the acoustic venting materials analysed can be used in ultrasonic venting applications, but the obtained knowledge about the response of these materials in the ultrasonic frequency range permit to advance in the selection of successful candidate materials for this application., Project Listen2Future funding is acknowledged. Under grant 101096884, Listen2Future is co-funded by the EU and by the Project Ref. PCI2022-135060-2 funded by CIN/AEI/10.13039/501100011033 and by EU “Next Generation EU”/PRTR, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Testing of polymeric battery separators using air-coupled, high-frequency and wideband ultrasonic pulses

  • Salso, Patricia
  • Genovés, Vicente
  • Merillas Valero, Beatriz
  • Gómez Álvarez-Arenas, Tomás
15 páginas, 7 figuras, 9 tablas., Separator membranes are one of the components in batteries and, although being a passive component, they may strongly affect both battery performance and security. Hence, effective control of both its main properties and their variability are critical issues for the battery industry. This work proposes testing these membranes by the measurement of the spectra of the ultrasonic transmission coefficient (magnitude and phase) using high- frequency and wideband air-coupled ultrasonic pulses. This non-conventional ultrasonic technique for mate- rials testing offers several advantages: it is completely contactless and non-invasive, it is very fast, and it has the potential to be deployed in the fabrication line to test the 100 % of the production in real time. This work shows that it is possible: a) to propagate high-frequency, wideband air-coupled ultrasonic pulses in the frequency range 0.15–2.4 MHz in battery separators, b) to obtain the transmission coefficient spectra, both magnitude and phase; c) to theoretically model this propagation and the transmission coefficient spectra in thin films and then d) to solve the inverse problem to extract some separator properties of interest. The obtained properties depend on the theoretical model use to describe the propagation. For separators with porosity <60 % and pore size big enough (approximately <1 μm for the separators studied here), effective medium approach can be successfully used, while for the other cases, the porous nature of the separator has to be taken into account and the Biot’s theory is used., Authors acknowledges funding from project Listen2Future. Under grant 101096884, Listen2Future is co-funded by the European Union and by the Project Ref. PCI2022-135060-2 funded by CIN/AEI/ 10.13039/501100011033 and by EU “NextGenerationEU”/PRTR. Views and opinions expressed are however those of the author(s) only and do not necessarily reflect those of the European Union or Key Digital Technologies Joint Undertaking. Neither the European Union nor the granting authority can be held responsible for them. The project is supported by the Key Digital Technologies Joint Undertaking and its members (including top-up funding by Austria, Belgium, Czechia, Ger- many, Netherlands, Norway, and Spain)., Peer reviewed
Archivo Digital UPM
Publication Artículo científico (JournalArticle)

Floating Capacitor Integrated DAB for Single-Phase, Single-Stage PFC in Wireless Battery Charging Application

  • Alzuguren Almorza, Itziar|||0000-0003-0147-5334
  • Garcia Bediaga, Asier|||0000-0002-8788-3875
  • Avila del Pozo, Ander|||0000-0002-1668-8933
  • Rujas Fernández, Alejandro
  • Vasic, Miroslav|||0000-0001-9597-6409