Skip to main content

DESARROLLO DE CODIGOS Y ALGORITMOS PARALELOS DE ALTAS PRESTACIONES CON FINES AL DISEÑO OPTIMIZADO DE SISTEMAS Y EQUIPOS TERMICOS

ENE2010-17801

•
Funding agency name Ministerio de Ciencia e Innovación
Funding agency acronym MICINN
Program Programa Nacional de Proyectos de Investigación Fundamental
Subprogram Subprograma de Proyectos de Investigación Fundamental no Orientada
Call Proyectos I+D
Call year 2010
State Plan 2008-2011 Plan Nacional de Investigación Científica, Desarrollo e Innovación Tecnológica
Management unit Subdirección General de Proyectos de Investigación
Beneficiary centre UNIVERSITAT POLITECNICA DE CATALUNYA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 12
Encontrada(s) 1 página(s)

UPCommons. Portal del coneixement obert de la UPC
Publication Contribución de congreso (ConferenceOutput)

Optimization of the thermal and fluid dynamic behaviour of air curtains: analysis of the plenum by means of LES

  • Giráldez García, Héctor
  • Pérez Segarra, Carlos David|||0000-0003-1007-3142
  • Rodríguez Pérez, Ivette María|||0000-0002-3749-277X
  • Oliva Llena, Asensio|||0000-0002-2805-4794
The improvement procedure of an air curtain unit (ACU) is described in the present study. The procedure is based on Large Eddy Simulations (LES) and Hot Wire Anemometry (HWA) measurements. Initially, the flow provided by the air curtain is evaluated experimentally according to the AMCA standard [1] and employing HWA technology. The initial measurements indicate an undesired behavior of the device: the velocity at the discharge exhibits a non homogeneous distribution. According to the literature, the efficiency of air curtains is closely related to its capacity to provide an homogeneous jet with high enough velocity and with low turbulence levels [2]. On this study, the criteria for optimization applied to the plenum chamber consist in finding out what design increases both the homogeneity and the mean velocity values produced at the discharge. An air curtain producing a jet with these features will minimize the air interchange between outdoor and indoor spaces. Alternative plenums are evaluated by means of fully 3D LES. Previous works indicate that a fully three-dimensional treatment is required in the simulations of ACUs [3], due to its no-bidimensional behaviour. The results of the simulations indicate that a more smooth plenum is required to avoid recirculations. The prototype of the designs with the best behavior, according to the simulations, are constructed and its flow are characterized with HWA measurements. The measurements show consistent results with LES. It is concluded that the proposed plenum geometry improves the initial design both in homogeneity and in mean velocity values at the discharge. The downstream jet evolution is characterised with semianalytical and experimental approaches. The code TermoFluids[4] has been used for the simulations of the plenum., This work has been financially supported by the Ministerio de Educacion y Ciencia, Spain (Project: ’Development of high performance parallel codes for the optimal design of thermal equipments’, reference ENE2010-17801) together with the companies Termofluids and Airtecnics., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Contribución de congreso (ConferenceOutput)

An OpenCL-based parallel CFD code for simulations on hybrid systems with massively-parallel accelerators

  • Gorobets, Andrei
  • Trias Miquel, Francesc Xavier|||0000-0002-5966-0703
  • Oliva Llena, Asensio|||0000-0002-2805-4794
A parallel finite-volume CFD algorithm for modeling of incompressible flows on hybrid supercomputers is presented. It is based on a symmetry-preserving high-order numerical scheme for structured meshes. A multilevel approach that combines di erent parallel models is used for large-scale simulations on computing systems with massively-parallel accelerators. MPI is used on the first level within the distributed memory model to couple computing nodes of a supercomputer. On the second level OpenMP is used to engage multiple CPU cores of a computing node. The third level exploits the computing potential of massively-parallel accelerators such as GPU (Graphics Processing Units) of AMD and NVIDIA, or Intel Xeon Phi accelerators of the MIC (Many Integrated Core) architecture. The hardware independent OpenCL standard is used to compute on accelerators of di erent architectures within a general model for a combination of a central processor and a math co-processor., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Contribución de congreso (ConferenceOutput)

A free surface model for the numerical simulation of oscillating water column systems

  • Schillaci, Eugenio|||0000-0002-6690-6871
  • Balcázar Arciniega, Néstor|||0000-0003-0776-2086
  • Jofre Cruanyes, Lluís|||0000-0003-2437-259X
  • Lehmkuhl Barba, Oriol|||0000-0002-2670-1871
  • Castro González, Jesús|||0000-0002-8943-2402
The aim of this work is to propose and validate a numerical model that represents the hydrodynamic behavior of an Oscillating Water Column (OWC) device, that has been shown to be one of the most promising ways to extract energy from ocean waves: successful demonstrative set-up have been realized both on shore based structures (LIMPET device in Scotland and PICO plant in Azores) and on anchored floating ones (OE Buoy in Ireland) [1]. A Level Set scheme was employed to track the free moving interface in an incompressible, transient two-phase flow, globally governed by the Navier-Stokes and the mass conservation equations. After being validated, the model was used to investigate the interaction of linear waves with a submerged air chamber; several set-up were analyzed by monitoring the characteristics magnitudes, in order to assess the accuracy of the model and to optimize the hydrodynamic efficiency of the device. In the second part, a single phase Level Set method was developed and used to simulate the same problem., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Contribución de congreso (ConferenceOutput)

Advanced CFD&HT numerical modeling of solar tower receivers

  • Colomer Rey, Guillem|||0000-0003-4592-0217
  • Chiva Segura, Jorge|||0000-0001-5466-6869
  • Lehmkuhl Barba, Oriol|||0000-0002-2670-1871
  • Oliva Llena, Asensio|||0000-0002-2805-4794
This paper presents an advanced methodology for the detailed modeling of the heat transfer and fluid dynamics phenomena in solar tower receivers. It has been carried out in the framework of a more ambitious enterprise which aims at modeling all the complex heat transfer and fluid dynamics phenomena present in central solar receivers. The global model is composed of 4 sub-models (heat conduction, two-phase flow, thermal radiation and natural convection) which are described., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Contribución de congreso (ConferenceOutput)

Large eddy simulation model assessment of the turbulent flow through dynamic compressor valves

  • Estruch Pérez, Olga
  • Lehmkuhl Barba, Oriol|||0000-0002-2670-1871
  • Rigola Serrano, Joaquim|||0000-0002-6685-3677
  • Oliva Llena, Asensio|||0000-0002-2805-4794
  • Pérez Segarra, Carlos David|||0000-0003-1007-3142
The present paper attempts the dynamic simulation of the fluid flow through the valve reed taking into account valve movement due to piston displacement. This work widens previous studies based on numerical experiments with static geometry and constant boundary conditions. Hence, in this work attends the newly in-house implemented CFD and moving mesh coupled code TermoFluids. The CFD solver consists of a three-dimensional explicit finite volume fractional-step algorithm formulated in a second-order, conservative and collocated unstructured grid arrangement. Large eddy simulation is performed to solve the turbulent flow, using the subgrid scale WALE model. A radial basis function interpolation procedure is used to dynamically move the mesh according with the displacement of the valve. A simplified geometry of an axial hole plus a radial diffuser with a piston based inlet condition is considered. The valve dynamics is assumed to be given by a law according modal analysis of valve reed., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Contribución de congreso (ConferenceOutput)

On the CFD&HT of the flow around a parabolic trough solar collector under real working conditions

  • Amine Hachicha, Ahmed
  • Rodríguez Pérez, Ivette María|||0000-0002-3749-277X
  • Lehmkuhl Barba, Oriol|||0000-0002-2670-1871
  • Oliva Llena, Asensio|||0000-0002-2805-4794
Parabolic trough solar collector is currently one of the most mature and prominent solar applications for production of electricity. These systems are usually located in open terrain where strong winds may occur and affect their stability and optical performance, as well as, the heat exchange between the solar receiver and the ambient air. In this context, a wind flow analysis around a parabolic trough solar collector under real working conditions is performed. A numerical aerodynamic and heat transfer study based on Large Eddy Simulations is carried out to characterize the wind loads and the heat transfer coefficients. Computations are performed for two Reynolds number ReW1=3.9×10^5 and ReW2=1×10^6 and various pitch angles. The effects of wind speed and pitch angle on the averaged and instantaneous flow have been assessed. The aerodynamic coefficients are calculated around the solar collectorand validated with measurements performed in wind tunnel tests. The variation of the heat transfer coefficient around the heat collector element with the Reynolds number is presented and compared to the circular cylinder in cross flow., Peer Reviewed
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Large eddy simulation model assessment of the turbulent flow through dynamic compressor valves

  • Estruch Pérez, Olga
  • Lehmkuhl Barba, Oriol
  • Rigola Serrano, Joaquim
  • Oliva Llena, Asensio
  • Pérez Segarra, Carlos David
The present paper attempts the dynamic simulation of the fluid flow through the valve reed taking into account valve movement due to piston displacement. This work widens previous studies based on numerical experiments with static geometry and constant boundary conditions. Hence, in this work attends the newly in-house implemented CFD and moving mesh coupled code TermoFluids. The CFD solver consists of a three-dimensional explicit finite volume fractional-step algorithm formulated in a second-order, conservative and collocated unstructured grid arrangement. Large eddy simulation is performed to solve the turbulent flow, using the subgrid scale WALE model. A radial basis function interpolation procedure is used to dynamically move the mesh according with the displacement of the valve. A simplified geometry of an axial hole plus a radial diffuser with a piston based inlet condition is considered. The valve dynamics is assumed to be given by a law according modal analysis of valve reed., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

On the CFD&HT of the flow around a parabolic trough solar collector under real working conditions

  • Amine Hachicha, Ahmed
  • Rodríguez Pérez, Ivette María
  • Lehmkuhl Barba, Oriol
  • Oliva Llena, Asensio
Parabolic trough solar collector is currently one of the most mature and prominent solar applications for production of electricity. These systems are usually located in open terrain where strong winds may occur and affect their stability and optical performance, as well as, the heat exchange between the solar receiver and the ambient air. In this context, a wind flow analysis around a parabolic trough solar collector under real working conditions is performed. A numerical aerodynamic and heat transfer study based on Large Eddy Simulations is carried out to characterize the wind loads and the heat transfer coefficients. Computations are performed for two Reynolds number ReW1=3.9×10^5 and ReW2=1×10^6 and various pitch angles. The effects of wind speed and pitch angle on the averaged and instantaneous flow have been assessed. The aerodynamic coefficients are calculated around the solar collectorand validated with measurements performed in wind tunnel tests. The variation of the heat transfer coefficient around the heat collector element with the Reynolds number is presented and compared to the circular cylinder in cross flow., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Optimization of the thermal and fluid dynamic behaviour of air curtains: analysis of the plenum by means of LES

  • Giráldez García, Héctor
  • Pérez Segarra, Carlos David
  • Rodríguez Pérez, Ivette María
  • Oliva Llena, Asensio
The improvement procedure of an air curtain unit (ACU) is described in the present study. The procedure is based on Large Eddy Simulations (LES) and Hot Wire Anemometry (HWA) measurements. Initially, the flow provided by the air curtain is evaluated experimentally according to the AMCA standard [1] and employing HWA technology. The initial measurements indicate an undesired behavior of the device: the velocity at the discharge exhibits a non homogeneous distribution. According to the literature, the efficiency of air curtains is closely related to its capacity to provide an homogeneous jet with high enough velocity and with low turbulence levels [2]. On this study, the criteria for optimization applied to the plenum chamber consist in finding out what design increases both the homogeneity and the mean velocity values produced at the discharge. An air curtain producing a jet with these features will minimize the air interchange between outdoor and indoor spaces. Alternative plenums are evaluated by means of fully 3D LES. Previous works indicate that a fully three-dimensional treatment is required in the simulations of ACUs [3], due to its no-bidimensional behaviour. The results of the simulations indicate that a more smooth plenum is required to avoid recirculations. The prototype of the designs with the best behavior, according to the simulations, are constructed and its flow are characterized with HWA measurements. The measurements show consistent results with LES. It is concluded that the proposed plenum geometry improves the initial design both in homogeneity and in mean velocity values at the discharge. The downstream jet evolution is characterised with semianalytical and experimental approaches. The code TermoFluids[4] has been used for the simulations of the plenum., This work has been financially supported by the Ministerio de Educacion y Ciencia, Spain (Project: ’Development of high performance parallel codes for the optimal design of thermal equipments’, reference ENE2010-17801) together with the companies Termofluids and Airtecnics., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

A free surface model for the numerical simulation of oscillating water column systems

  • Schillaci, Eugenio
  • Balcázar Arciniega, Néstor
  • Jofre Cruanyes, Lluís
  • Lehmkuhl Barba, Oriol
  • Castro González, Jesús
The aim of this work is to propose and validate a numerical model that represents the hydrodynamic behavior of an Oscillating Water Column (OWC) device, that has been shown to be one of the most promising ways to extract energy from ocean waves: successful demonstrative set-up have been realized both on shore based structures (LIMPET device in Scotland and PICO plant in Azores) and on anchored floating ones (OE Buoy in Ireland) [1]. A Level Set scheme was employed to track the free moving interface in an incompressible, transient two-phase flow, globally governed by the Navier-Stokes and the mass conservation equations. After being validated, the model was used to investigate the interaction of linear waves with a submerged air chamber; several set-up were analyzed by monitoring the characteristics magnitudes, in order to assess the accuracy of the model and to optimize the hydrodynamic efficiency of the device. In the second part, a single phase Level Set method was developed and used to simulate the same problem., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Advanced CFD&HT numerical modeling of solar tower receivers

  • Colomer Rey, Guillem
  • Chiva Segura, Jorge
  • Lehmkuhl Barba, Oriol
  • Oliva Llena, Asensio
This paper presents an advanced methodology for the detailed modeling of the heat transfer and fluid dynamics phenomena in solar tower receivers. It has been carried out in the framework of a more ambitious enterprise which aims at modeling all the complex heat transfer and fluid dynamics phenomena present in central solar receivers. The global model is composed of 4 sub-models (heat conduction, two-phase flow, thermal radiation and natural convection) which are described., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

An OpenCL-based parallel CFD code for simulations on hybrid systems with massively-parallel accelerators

  • Gorobets, Andrei
  • Trias Miquel, Francesc Xavier
  • Oliva Llena, Asensio
A parallel finite-volume CFD algorithm for modeling of incompressible flows on hybrid supercomputers is presented. It is based on a symmetry-preserving high-order numerical scheme for structured meshes. A multilevel approach that combines di erent parallel models is used for large-scale simulations on computing systems with massively-parallel accelerators. MPI is used on the first level within the distributed memory model to couple computing nodes of a supercomputer. On the second level OpenMP is used to engage multiple CPU cores of a computing node. The third level exploits the computing potential of massively-parallel accelerators such as GPU (Graphics Processing Units) of AMD and NVIDIA, or Intel Xeon Phi accelerators of the MIC (Many Integrated Core) architecture. The hardware independent OpenCL standard is used to compute on accelerators of di erent architectures within a general model for a combination of a central processor and a math co-processor., Peer Reviewed, Postprint (published version)