Skip to main content

AVANCES EN MEMBRANAS DE FIBRA HUECA BASADAS EN MOFS Y GRAFENO ENFOCADAS A PROCESOS EFICIENTES DE SEPARACION

MAT2016-77290-R

•
Funding agency name Agencia Estatal de Investigación
Funding agency acronym AEI
Program Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Call Proyectos I+D+i Retos de Investigación
Call year 2016
State Plan 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Beneficiary centre UNIVERSIDAD DE ZARAGOZA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 4
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

MOF synthesis on carbon nanotubes buckypaper for gas separation

  • Berned-Samatán, Víctor
  • Galán, Alejandro
  • Rubio, César
  • Perea-Cachero, Adelaida
  • Muñoz, Edgar
  • Benito, Ana M.
  • Maser, Wolfgang K.
  • Téllez, Carlos
  • Coronas, Joaquín
Resumen del trabajo presentado a la XXXVII Reunión Bienal de la Real Sociedad Española de Química, celebrada en Donostia-San Sebastián del 26 al 30 de mayo de 2019., Financial support from the Spanish Ministry of Economy and Competitiveness (MINECO) and European Regional Development Fund (MAT2016-77290-R), ESF and the Aragón Government (T43-17R) is gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

TEM characterization of nanocomposite polymer membranes with MOF fillers for nanofiltration

  • Navarro, Marta
  • Paseta, Lorena
  • Echaide‐Górriz, Carlos
  • Benito, Javier
  • Gascón, Ignacio
  • Coronas, Joaquín
  • Téllez, Carlos
Póster presentado al Microscopy at the Frontiers of Science Congress Series (MFS), celebrado en el Parque de las Ciencias de Granada (España) del 11 al 13 de septiembre de 2019., Thin film composite (TFC) membranes consist of a polyamide (PA) thin film (35-100 nm thick) as a selective layer, grown via interfacial polymerization (IP) of monomeric acid chlorides and amines on top of an asymmetric polyimide support, cast over a polypropylene non-woven backing material by phase inversion. This type of membrane is very competitive for organic solvent nanofiltration, where chemical stable polymers are mandatory. In order to increase membrane flux without decreasing rejection, nanoparticles are incorporating during the IP process, giving rise to Thin film nanocomposite (TFN) membranes (Fig. 1a). Their performance is determined by the structural and physicochemical properties of the fillers and PA thin film. Metal organic frameworks (MOFs), built from organic linkers and metal-containing clusters, have been extensively included as fillers in TFN membranes, showing exceptional affinity with polymer chains and improved solvent permeation. The combination of nanoscale visualization via conventional Transmission electron microscopy (TEM) and Scanning transmission electron microscopy (STEM), and spectroscopic analysis via energy dispersive X-ray spectroscopy (EDX) and Electron energy loss spectroscopy (EELS), are some of the most potent techniques for shedding further light into the connection between the nanostructure of the MOF-PA film and their transport and rejection properties. Sample preparation is a key step to examine the presence, distribution and morphology of MOF nanoparticles within the PA film, but also to confirm their crystallinity after the IP process by electron microscopy, given the multilayer and heterogeneous character of these membranes and but also because of the beamsensitive nature of MOFs. Here, we report different sample preparation protocols for applying TEM, STEM-EDS/EELS and electron diffraction depending on the nature of the TFN sample and on the characterization aim: 1. When the aim was to confirm the presence, distribution and morphology of two types of MOFs of different chemical composition in the PA layer, a fragment of the MOF-PA film was detached from the polyimide support in the last stage of the IP process. The fragment was removed from the distilled water bath and placed onto a carbon film grid. TEM and STEM-EDS techniques were applied. 2. When the objective was to check the distribution of the MOF nanoparticles within the TFN membrane and their crystallinity, a MOF-TFN membrane was synthesized over a non-crosslinked polyimide support without backing material. Then, the membrane was immersed in N,N-dimethylformamide at room temperature for 5 min to dissolve the polyimide support. The separated PA top layer was placed onto a carbon film grid. TEM and electron diffraction were applied. 3. When the goal was to verify the presence of a defect free MOF monolayer film in between the two polymer layers (Fig. 1b), transferred by the Langmuir-Schaefer (LS) technique, a lamella (∼80 nm thick) was obtained from the upper 2 μm of the TFN membrane using cryo-focused ion beam (FIB) equipment (Dual Beam 3 Nova 200) and Ga atoms for the etching. STEM-EDS/EELS techniques were applied (Fig. 1c)., Financial support from the Research Project MAT2016-77290-R (MINECO/AEI/FEDER, UE) is gratefully acknowledged., Peer reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Contribución de congreso (ConferenceOutput)

Ultrathin composite polymeric membranes for CO2/N2 separation with minimum thickness and high co2 permeance

  • Benito, Javier
  • Sánchez-Laínez, Javier
  • Zornoza, Beatriz
  • Martín, Santiago
  • Carta, Mariolino
  • Malpass-Evans, Richard
  • Téllez, Carlos
  • McKeown, Neil B.
  • Coronas, Joaquín
  • Gascón, Ignacio
The use of ultrathin films as selective layers in composite membranes offers significant advantages in gas separation for increasing productivity while reducing the membrane size and energy costs. In this contribution, composite membranes have been obtained by the successive deposition of approximately 1 nm thick monolayers of a polymer of intrinsic microporosity (PIM) on top of dense membranes of the ultra-permeable poly[1-(trimethylsilyl)-1-propyne] (PTMSP). The ultrathin PIM films (30 nm in thickness) demonstrate CO2 permeance up to seven times higher than dense PIM membranes using only 0.04¿% of the mass of PIM without a significant decrease in CO2/N2 selectivity.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Contribución de congreso (ConferenceOutput)

The Effect of Hydrogen Peroxide on the synthesis of Terephthalate-Based metal-organic frameworks

  • Monteagudo-Olivan, Rebeca
  • Jiménez-Fernández, Isabel
  • López-Ram-de-Viu, Pilar
  • Sebastian, Víctor
  • Coronas, Joaquín
Metal-organic frameworks (MOFs) are versatile materials for applications in fields including the environment, energy and health. A synthetic route for improving the formation of MOFs has been developed and is triggered by hydrogen peroxide (H2O2) to promote the formation of terephthalate-based MOFs of MIL-53 and MIL-68 types, specifically those made from Fe3+ and Al3+ and mixtures of both. Different characterization techniques (TGA, XRD, SEM, TEM, N2 porosimetry and Raman, mass and NMR spectroscopies) gave insights into the effect of H2O2 on the MOF synthesis. The reaction yield was significantly improved (the highest yield being 74 % for MIL-53(Al)), while crystallinity and N2 adsorption properties were mostly maintained for phases based on Al and Al/Fe. Furthermore, a reaction mechanism was envisaged from the mass spectroscopic analysis of the reaction solutions, thus suggesting that H2O2 plays the role of a µ-hydroxo bridge promoter, favoring the link between terephthalate ligands and aluminum-containing species to give rise to the µ-carboxylate bridges, leading to a faster growth of the final MOF, and offering a novel MOF synthesis approach.