Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 2
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Investigation of Cd-free Sb2Se3 Thin-Film Solar Cells by ALD-ZnSnO Electron Transport Layer

  • Lázaro-Castrillón, Luna
  • Sánchez, Yudania
  • Payno, David
  • Razi, Umair
  • Bonal, Víctor
  • Cabello, Fátima
  • Galiana, Beatriz
  • Pérez-Rodríguez, Alejandro
  • Merino, José Manuel
  • Caballero, Raquel
4 pages, 5 figures, 1 table . -- 42nd European Photovoltaic Solar Energy Conference and Exhibition , 22-26 September, Bilbao, España, Most of the efficient Sb2Se3-based PV devices use CdS as electron transport layer (ETL) or/and an organic hole transport layer. With the objective of fabricating non-toxic and stable solar cells, we investigate substrate Sb2Se3 thin-film PV devices by the replacement of CdS by Zn1-xSnxO (ZTO) layer without using an organic material in the device structure. In this work, Sb2Se3 thin films have been grown by selenization of evaporated Sb layer onto Mo/SLG substrates. ZTO films are fabricated by atomic layer deposition (ALD) to develop Cd-free solar cells, while the reference CdS layer is deposited by chemical bath. The absorber presents an orthorhombic structure with [hk1] preferred orientation, and a compact structure free of pinholes. The different techniques used for the fabrication of the ETLs show the different CdS and ZTO morphologies, with a conformal growth and uniform surface for the ZTO. ITO/ZnO/CdS/Sb2Se3/Mo/SLG and ITO/ZnO/ZnSnO/Sb2Se3/Mo/SLG solar cells are fabricated. A total efficiency of 4.3 % for the CdS/Sb2Se3 solar cell and of 3.0 % for the Cd-free PV device are obtained. It is revealed that ZTO thickness is a critical parameter to optimize the heterojunction. In this work, 40 nm ZTO layer leads to higher device performances., This work was supported by SUNLIFE (PCI2024 155033-2) project funded by MICIU/AEI/10.13039/501100011033/UE, ASSESS (TED2021-129666B-C21 and TED2021-129666B-C22) project funded by MCIN/AEI/10.13039/501100011033 and by the “European Union Next Generation EU/PRTR” and InnoPV (PID 2022-140226OB-C3) funded by MICIU/AEI/10.13039/501100011033 and by “FEDER/UE”. We also acknowledge the service from the MiNa Laboratory at IMN-CSIC, and funding from CM (project S2018/NMT-4291 TEC2SPACE), MINECO (project CSIC13-4E-1794) and EU (FEDER, FSE)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Monolithic Interconnection of Thin Film Minimodule Prepared by a CNC Mechanical Scribing

  • Payno, David
  • Andrade-Arvizu, Jacob
  • Miró-Llorente, Marta
  • Vidal-Fuentes, Pedro
  • Caballero, Raquel
  • Izquierdo-Roca, Víctor
  • Pérez-Rodríguez, Alejandro
3 pages, 5 figures, 1 table . -- 42nd European Photovoltaic Solar Energy Conference and Exhibition , 22-26 September, Bilbao, España, Monolithic interconnection is a key strategy for thin-film photovoltaic (PV) modules, enabling dense series-connected cell arrays without external wiring. Conventional laser scribing, however, requires complex optimization and can be unsuitable for high-melting-point or highly transparent materials. This work demonstrates a low-cost, flexible alternative based on fully mechanical scribing using a computer numerical control (CNC) system. Kesterite (Cu₂ZnSnSe₄) thin-film minimodules with Mo/CZTSe/CdS/ZnO/ITO architecture were fabricated and interconnected into an 8-cell series configuration. By selecting scribing tips of different hardness, specific layers were selectively removed without damaging underlying contacts, achieving effective P1–P2-P3 patterning. The interconnected module delivered a total open-circuit voltage of 2.65 V, consistent with the sum of individual cell voltages, while maintaining comparable current and shunt resistance. Main performance losses arose from increased series resistance and reduced active area, limiting power conversion efficiency to 2% for the module, 3.1% for the module active area, versus a efficiency of 6% for an individual reference cell. These results highlight mechanical scribing as a practical method for early-stage PV technologies and a potential complement to laser scribing in industrial applications, This project has received funding from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 952982 (Custom-Art) and the Project ASSESS (TED2021-129666B-C21) funded by MCIN/AEI/ 10.13039/501100011033, Peer reviewed