Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 27
Encontrada(s) 1 página(s)

Repisalud
Publication Tesis doctoral (DoctoralThesis)

Role of NRG1 in Mouse Heart Development

  • Gomez-Apinaniz, Paula
During embryonic development, cellular interactions are crucial to orchestrate the processes that give rise to the final body plan. The heart is the first organ to form and function during development. The formation of trabeculae, myocardial protrusions covered by endocardium that grow towards the lumen of the ventricles, is the first sign of chamber development, and occurs in response to signals from the endocardium that activate the overlying myocardium. Trabeculae are crucial for increasing the internal ventricular surface, favouring oxygen exchange and nourishment of the cardiomyocytes. Previous studies in mice have shown that NEUREGULIN1 (NRG1), a ligand belonging to the Epidermal Growth Factor family expressed in the endocardium, and its more widespread receptors -ERBB2,4- are crucial for ventricular trabeculation, but the cellular processes affected by Nrg1 loss in the heart are not well understood. To gain an insight into the role of NRG1 in heart development, we have used conditional loss- and gain-of-function mouse models. We have found that endothelial-specific, Tie2Cre-mediated, Nrg1 inactivation disrupts trabecular morphology and patterning, and reduces ventricular cardiomyocyte proliferation, while paradoxically, the compact myocardium appeared thickened. Global gene expression analysis in embryonic hearts by RNA-seq revealed a dysregulation of apico-basal polarity marker genes. We thus examined whether cellular polarity and oriented cell division were affected in chamber cardiomyocytes. We observed a loss of polarity (LAMININS-ITGα6, PKC, N-CADHERIN) in cardiomyocytes, and an increase in parallel divisions in chamber cardiomyocytes of Nrg1flox;Tie2Cre mutants. This finding would explain the thickened compact myocardium and the impaired trabeculation of these mice. In addition to trabeculation defects, Nrg1flox;Tie2Cre mutant hearts show hypoplastic valves, due to impaired epithelial-mesenchyme transition (EMT) of presumptive valve endocardial cells, presumably because binding and activation of the receptor ERBB2,3 by NRG1 in this region is impaired. To study the function of NRG1 signalling at later stages of ventricular chamber development, we have induced Nrg1 deletion during compaction, using the Cdh5CreERT2 driver. Late Nrg1 inactivation in cardiac endothelium leads to a thinner compact myocardium, and defective myocardial patterning and coronary vessel morphogenesis. We have also generated a conditional gain-of-function transgenic line for NRG1. Tie2Cre-mediated Nrg1 overexpression lead to thickened valves, and Nkx2.5Cre-mediated Nrg1 lead also to thickened valves, ventricular septal defect and ventricular chamber dilation. Our results indicate that NRG1 is essential from early to late stages of ventricular wall development. NRG1 is required for cardiomyocyte polarization and oriented cell division during trabeculation, for endocardial cushion formation during valve development, and for chamber maturation and coronary vessel formation during compaction.
Repisalud
Publication Tesis doctoral (DoctoralThesis)

Unraveling the molecular mechanisms behind the regulation of mesenchymal cell proliferation during cardiac valve remodeling

  • Ferreira Oliveira, Vera Lúcia
The importance of the cardiac valves is apparent when one considers how often they are required to open and shut on a minute-to-minute basis. The complexity of their formation is underlined by the frequent involvement of valvular defects in several forms of congenital heart disease. Even though many of these defects are subtle, they often lead to disease and significant mortality later in life. Therefore, a comprehensive understanding of the mechanisms underlying valvulogenesis is of critical clinical importance. The chemokine receptor CXCR4 and its ligand CXCL12 are known to play important roles in cell mobility and behavior in various contexts. Targeted deletion of Cxcr4 using an endothelial driver has been shown to hamper the remodeling of the cardiac valves, which develop thickened leaflets. Nonetheless, the precise mechanism through which these chemotactic cytokines act during cardiac valvulogenesis remains unclear. The growth factor HBEGF is synthe The growth factor HBEGF is synthesized as a membrane bound proprotein that, upon cleavage, is released in order to activate nearby receptors, such as EGFR. Both soluble HBEGF (sHBEGF) itself and members of its pathway have been established as important players in valve formation. Several studies have demonstrated that disruption of members of the HBEGF-EGFR pathway results in valvular phenotypes similar to the ones observed upon Cxcr4 deletion. Our understanding of the molecular mechanisms underlying valve maturation is still limited. Even though many of the proteins and pathways involved have been studied in the last two decades, there is still much to be determined regarding the role they play and how they interact. Using novel mouse models, our aim was to obtain new knowledge about the CXCL12-CXCR4 and the HBEGF-EGFR signaling pathways during the remodeling phase of valvulogenesis. With that in mind, we began by corroborating how endocardial loss of Cxcr4 recapitulated the thickened leaflets phenotype previously found in other studies, with an associated increase in the proliferation of mesenchymal cells. This in vivo observation was further confirmed with the ex vivo system of outflow tract (OFT) heart explants. Treatment of control OFT explants with the CXCR4 antagonist AMD3100 confirmed the increase in mesenchymal cell proliferation. Another genetic tool we have employed is a mouse model that specifically overexpresses sHBEGF in endothelial cells, which we have generated using restriction cloning techniques. Surprisingly, we have found that the extra release of sHBEGF also led enlarged valves, accompanied by increased valve mesenchymal cell proliferation. Control OFT explants treated with recombinant sHBEGF also resulted in a pronounced increase in mesenchymal proliferation. Activation of different receptors or receptor dimers might explain the discrepancies between these observations and previous studies. These preliminary results point towards a novel role for CXCR4 during valve remodeling. Furthermore, they highlight the importance of the precise regulation of sHBEGF levels during this process. Further analysis of both of these pathways could help uncover how the process of valvulogenesis goes awry in the many different forms of congenital valve disease.
Repisalud
Publication Tesis doctoral (DoctoralThesis)

Retrospective clonal analysis of the developing mouse heart

  • Lioux, Ghislaine
The cardiac OFT is composed of endothelial cells (ECs), smooth muscle cells (SMCs), fibroblasts (Fbs) and Cardiomyocytes (CMs) known to derive from neural crest and second heart field (SHF) progenitors. The OFT is also covered by a mesothelial sheet of arterial mesothelial cells (AMCs) continuous with the epicardium. While the epicardium arises from the proepicardium, the early progenitor of AMCs is unknown. Using mesothelial and SHF related Cre lines we identified the origin of AMCs to be in the dorsal pharyngeal mesoderm. During a systematic analysis of cardiac lineages by random clonal labelling in developing mouse hearts, we found that AMCs shared a clonal relationship with cells of the great arteries. AMC clones were of different nature along the great arteries. On one hand, distal AMCs in both vessels were clonally related to Fbs, SMCs and ECs. On the other hand, the proximal AMCs of the Pulmonary artery (PA), were clonally related to Fbs, SMCs, CMs and lymphatic endothelial cells (LECs) of the ventral part of the heart. These clones however, were never found together with lymphatic clones of the dorsal part of the heart suggesting multiple origins for cardiac lymphatic vessels. Fate mapping of VEGFR3+ progenitors at different stages showed that whereas dorsal lymphatics derive from pre-existing lymphatic vessels, formation of ventral lymphatics involves the late recruitment of nonlymphatic cells. Using a range of SHF-specific Cre lines, we found that SHF-derived cells form ventral but not dorsal cardiac lymphatics. These observations suggest that SHF progenitors are recruited in the mesothelial-sub-mesothelial region of the PA. To test this hypothesis, we transplanted portions of PA mesothelial/sub-mesothelial layers from fluorescent donors into wild type E14.5 hearts. Donor tissue invaded the host myocardium, forming lymphatic vessels. The exploration of molecular cues involved in the formation of that niche showed that Raldh2 is downregulated at transcriptional and protein levels in proximal AMCs. Moreover, the loss of RA signalling in mesothelial cells resulted in immature lymphatic vessels while an excess of RA triggered lymphatic hyper-remodelling in the PA. These data show that part of the ventral lymphatics form by recruitment of SHF progenitors at a vasculogenic niche specified in a low Raldh2 environment at the base of the PA.
Repisalud
Publication Tesis doctoral (DoctoralThesis)

The Role of Meis Transcription Factors in Cardiomyocytes

  • Munoz Martin, Noelia
The heart is the pump that irrigates the body to satisfy the nutrient and oxygen demands essential for keeping the organism alive. Understanding how the heart is formed and how its homeostasis is maintained in adulthood, is of great interest and can provide new insights on the etiology of cardiovascular diseases. In this doctoral thesis we studied the role of Meis1 and Meis2 transcription factors as possible regulators of cardiac development and homeostasis. We developed two mouse models for the conditional simultaneous deletion of Meis1 and Meis2 in cardiomyocytes either during development or during adulthood. Analysis of Meis1 and Meis2 double deletion in the developing heart revealed cardiac malformations and perinatal death, together with impaired electrical impulse propagation through the ventricles. Adult mice with Meis1 and Meis2 loss of function in cardiomyocytes presented mild cardiac hypertrophy, polyploidization of mononucleated cardiomyocytes and impaired electrical impulse conduction through ventricular myocardium. The transcriptomic analysis of the mutants suggests that Meis1 and Meis2 transcription factors regulate calcium and sodium currents and GAP junction communication in developing and adult cardiomyocytes, which is in accordance with the electrical phenotypes observed. Moreover, the set of genes sensitive to Meis1 and Meis2 deletion shows significant coincidence with those altered in mouse models of arrhythmogenic right ventricular cardiomyopathy, suggesting a role for these transcription factors in the pathogenesis of this disease.
Repisalud
Publication Tesis doctoral (DoctoralThesis)

P53 and PUMA in Pluripotent Cell Competition, P53 y PUMA en Competición Celular en células Pluripotentes

  • Valverde López, José Antonio
Cell Competition (CC) is a biological process in which viable cells are eliminated by the presence of neighbouring cells with increased fitness. First observed in Drosophila, Cell Competition has been described in numerous biological scenarios in metazoans both du¬ring embryonic development and in the adult. Cell Competition has been envisioned as a conserved and extended quality control system that eliminates less fit, mispatterned or non-well adapted cells, ensuring homeostasis and proper function of tissues and organs throughout life. During the early mouse development, the mouse epiblast and its in vitro counterpart, mouse embryonic stem cells (ESCs) are subjected to natural Cell Competition. Through this mechanism, suboptimal or potentially harmful cells are removed by the presence of fitter cells, optimizing the pool of cells that will give rise to the new individual. This endogenous CC model correlates with MYC transcription factor expression, so cells with low MYC levels are eliminated by the presence of cells with higher levels (Clavería et al., 2013; Díaz-Díaz et al., 2017; Sancho et al., 2013). This process relies on the interaction and comparison between cells with different fitness, which results in the elimination of less fit cells. However, these molecular mechanisms remain largely unknown, especially in mammals. Here, we have explored different factors and pathways regulating cell fitness and the execution of loser cell death. We have identified and analysed different candidates of the P53 pathway and propose a model based on increased susceptibility to apoptosis, autophagy and mitophagy induction and reduction of mitochondrial OXPHOS function, accounting, at least in part, for the loser “signature” in pluripotent Cell Competition. We have found that P53 and PUMA regulate apoptosis susceptibility in ESCs but their function and expression is not restricted to apoptotic cells. We have shown that P53 activity inhibits MYC expression and is strictly required for PUMA expression. P53 and PUMA regulate fitness and induces Cell Competition in ESCs. P53 regulation of competitive fitness depends on the pluripotency status, with the pathway being activated as the cells progress towards differentiation and their ability to induce Cell Competition is supressed in naïve pluripotency conditions. We propose a model that integrates the P53 pathway and MYC in the definition of the lo¬ser cell fitness “status” and suggests that an alteration in mitochondrial OXPHOS function regulated by P53-PUMA underlies competitive fitness in pluripotent cells.
Repisalud
Publication Tesis doctoral (DoctoralThesis)

Meis Transcription Factor in Axial Development

  • Lopez Delgado, Alejandra Cristina
Metazoan antero-posterior patterning is established during development and in vertebrates its organization can be studied through the specific morphologies of vertebrae depending on their position along the rostro-caudal axis. Hox genes encode DNA-binding homeodomain transcription factors essential for the specification of axial skeletal identities. The specificity and affinity of Hox proteins in DNA binding and axial identity specification depends on interactions with cofactors. Meis transcription factors form different molecular complexes required for Hox proteins to efficiently regulate their targets. In this thesis we show that Meis is involved in the specification of axial identities and skeletal patterning, by showing that the deletion of Meis produces anterior homeotic transformations and other skeletal defects affecting the occipital, cervical, thoracic and anterior lumbar region. The abnormalities observed in the skeleton of Meis-deficient mice do not involve changes in Hox gene expression, despite the extensive binding of Meis to Hox genetic complexes, and therefore, their role as Hox cofactors could underlie the homeotic functions described. Through molecular analyses, we found retinoic acid signaling deficiencies in Meis mutants and identified the gene Raldh2, which codifies for the main embryonic retinoic acid synthesizing enzyme, as a putative direct Meis target. A compared analysis of Meis and Raldh2 mutants identifies similar alterations of the skeletal pattern, which suggests that, at least in part, Meis roles in axial skeleton patterning are conveyed by regulation of the retinoic acid pathway. Besides homeotic transformation, we found defective patterning of the distal segments of ribs, which we correlated with defects in molecular pathways required for hypaxial muscle development. The results presented characterize the functions of Meis genes in axial skeletal patterning and identify molecular pathways by which they perform these functions.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Tesis doctoral (DoctoralThesis)

Study of Combinatorial Cell Therapy and Neuroprotective Agents for the Treatment of Spinal Cord Injury in Experimental Models

  • Bonilla Villamil, Pablo
[ES] La lesión medular (LM) es un trastorno neurológico devastador y debilitante que se caracteriza por un grado variable de disfunción motora, sensorial y/o autonómica permanente. El trasplante de células madre neurales (NSC) ofrece una herramienta terapéutica prometedora para el tratamiento de la LM al proporcionar neuroprotección y neuroregeneración. Sin embargo, el entorno generado tras la lesión limita el potencial terapéutico de las terapias celulares al dar lugar a una escasa supervivencia y engraftment de las células y a una diferenciación inadecuada. Además, las terapias celulares han mostrado hasta la fecha una recuperación funcional limitada en los ensayos clínicos. Por lo tanto, se ha postulado el uso de terapias combinatorias para superar estas limitaciones y potenciar los beneficios terapéuticos de las terapias celulares. En esta tesis doctoral, se han estudiado distintas estrategias de combinación con el trasplante de NSC, como el uso de fármacos y biomateriales, con el objetivo de mejorar y potenciar el efecto de la terapia celular en el rescate de la actividad neuronal, en la modulación del proceso inflamatorio, en la supervivencia del trasplante, así como en su integración y diferenciación en el tejido medular. Así, En el capítulo 1 evaluamos la terapia combinada de células madre neurales humanas derivadas de células madre pluripotentes inducidas (iPSC-NSCs), células madre mesenquimales (MSCs) y un nanoconjugado de curcumina (PA-C) en un modelo de LM subagudo, proporcionando un mayor grado de neuroprotección en comparación con los tratamientos individuales. En el capítulo 2 desarrollamos una estrategia mínimamente invasiva mediante el uso de un scaffold de ácido hialurónico en forma de semi-luna para el transplante de iPSC-NSCs combinado con PA-C. Así, los análisis histológicos demostraron que el tratamiento combinado de iPSC-NSCs y la PA-C presentaban una mayor preservación de fibras neuronales en la zona de la lesión y una reducción de la extensión de la cicatriz fibrótica. Por último, en el capítulo 3 se describe una estrategia terapéutica que se aproxima más a la traslación clínica mediante el trasplante de progenitores neurales fetales humanos (hfNPCs) condicionados previamente con una forma conjugada del inhibidor de Rho/Rock fasudil (PGA-SS-FAS). Así, la combinación de las hfNPCs con el PGA-SS-FAS favoreció la migración del transplante en el tejido medular, la preservación de las interneuronas somatosensoriales Lbx1 inhibitorias y las Tlx3 excitatorias, así como la activación neuronal alrededor del epicentro de la lesión. Así pues, en la presente tesis doctoral se estudia y describe el beneficio aportado por tres estrategias combinatorias, que incrementan los efectos neuroprotectores proporcionados por la terapia celular en el tratamiento de lesiones medulares agudas y sub-agudas., [CA] La lesió medul·lar (LM) és un trastorn neurològic devastador i debilitant que es caracteritza per un grau variable de disfunció motora, sensorial i/o autonòmica permanent. El trasplantament de cèl·lules mare neurals (NSC) ofereix una eina terapèutica prometedora per al tractament de la LM proporcionant neuroprotecció i neuroregeneració. Tot i això, l'entorn generat després de la lesió limita el potencial terapèutic de les teràpies cel·lulars donant lloc a una escassa supervivència i engraftment de les cèl·lules i a una diferenciació inadequada. A més, les teràpies cel·lulars han mostrat fins ara una recuperació funcional limitada als assajos clínics. Per tant, s'ha postulat l'ús de teràpies combinatòries per superar aquestes limitacions i potenciar els beneficis terapèutics de les teràpies cel·lulars. En aquesta tesi doctoral, s'han estudiat diferents estratègies de combinació amb el trasplantament de NSC, com ara l'ús de fàrmacs i biomaterials, amb l'objectiu de millorar i potenciar l'efecte de la teràpia cel·lular en el rescat de l'activitat neuronal, en la modulació del procés inflamatori, en la supervivència del trasplantament, així com en la seva integració i diferenciació al teixit medul·lar. Així, Al capítol 1 avaluem la teràpia combinada de cèl·llules mare neurals humanes derivades de cèl·lules mare pluripotents induïdes (iPSC-NSCs), cèl·lules mare mesenquimals (MSCs) i un nanoconjugat de curcumina (PA-C) en un model de LM subagut, proporcionant un major grau de neuroprotecció en comparació dels tractaments individuals. Al capítol 2 desenvolupem una estratègia mínimament invasiva mitjançant l'ús d'un scaffold d'àcid hialurònic en forma de semilluna per al trasplantament d'iPSC-NSC combinat amb PA-C. Així, els anàlisis histològics mostraren que el tractament combinat d'iPSC-NSCs i la PA-C incrementaba la preservació de fibres neuronals a la zona de la lesió i reduïa l'extensió de la cicatriu fibròtica. Finalment, al capítol 3 es descriu una estratègia terapèutica que s'aproxima més a la translació clínica mitjançant el trasplantament de progenitors neurals fetals humans (hfNPCs) condicionats prèviament amb una forma conjugada de l'inhibidor de Rho/Rock fasudil (PGA-SS-FAS. Així, la combinació de les hfNPCs amb el PGA-SS-FAS va afavorir la migració del trasplantament al teixit medul·lar, la preservació de les interneurones somatosensorials Lbx1 inhibitòries i les Tlx3 excitatòries, així com l'activació neuronal al voltant de l'epicentre de la lesió. Així doncs, en aquesta tesi doctoral s'estudia i descriu el benefici aportat per tres estratègies combinatòries, que incrementen els efectes neuroprotectors proporcionats per la teràpia cel·lular en el tractament de lesions medul·lars agudes i sub-agudes., [EN] Spinal cord injury (SCI) is a devastating and debilitating neurological disorder characterized by a variable degree of permanent motor, sensory and/or autonomic dysfunction. Neural stem cell (NSC) transplantation offers a promising therapeutic tool for the treatment of SCI by providing neuroprotection and neuroregeneration. However, the environment generated after injury limits the therapeutic potential of cell therapies by resulting in poor cell survival and engraftment and inadequate differentiation. In addition, cell therapies have shown limited functional recovery in clinical trials to date. Therefore, the use of combinatorial therapies has been postulated to overcome these limitations and enhance the therapeutic benefits of cell therapies. In this doctoral thesis, we have studied different combination strategies with NSC transplantation, such as the use of drugs and biomaterials, with the aim of improving and enhancing the effect of cell therapy in the rescue of neuronal activity, in the modulation of the inflammatory process, in the survival of the transplant, as well as in its integration and differentiation in the medullary tissue. Thus, In Chapter 1 we evaluated the combined therapy of human induced pluripotent stem cell-derived neural stem cells (iPSC-NSCs), mesenchymal stem cells (MSCs) and a curcumin nanoconjugate (PA-C) in a subacute LM model, providing a higher degree of neuroprotection compared to single treatments. In Chapter 2, we developed a minimally invasive strategy by using a demilune hyaluronic acid scaffold for combined transplantation of iPSC-NSCs with PA-C. Thus, histological analyses demonstrated that the combined treatment of iPSC-NSCs and PA-C exhibited increased preservation of neuronal fibers in the lesion area and a reduction in the extension of the fibrotic scar. Finally, Chapter 3 describes a therapeutic strategy that more closely approximates clinical translation by transplanting human fetal neural progenitors (hfNPCs) preconditioned with a conjugated form of the Rho/Rock inhibitor fasudil (PGA-SS-FAS). Thus, the combination of hfNPCs with PGA-SS-FAS favored transplant migration within the spinal parenchyma, preservation of endogenous inhibitory Lbx1 and excitatory Tlx3 somatosensory interneurons, as well as endogenous neuronal activation around the lesion epicenter. Thus, this PhD thesis studies and describes the benefit provided by three combinatorial strategies, which increase the neuroprotective effects provided by cell therapy in the treatment of acute and sub-acute spinal cord injury., This research was funded by Fundació Marató TV3 2017/refs.20172230, 20172231 and 20172110; FEDER/Ministerio de Ciencia e Innovación–Agencia Estatal de Investigación “RTI2018- 095872-B-C21/ERDF”, Agencia Valenciana de Innovación (AVI) INNVAL10/19/047 and TERCEL (RD12/0019/0011) funds from the Instituto de Salud Carlos III of Spain; Science by Women program, Women for Africa Foundation to HE and the grants FEDER/Ministerio de Ciencia e Innovación – Agencia Estatal de Investigación [RTI2018-095872-B-C21 and –C22/ERDF]; RISEUP project FetOpen in H2020 Program: H2020-ETOPEN-2018-2019-2020-01 and by Grants RTI2018-095872-B-C21 and PDI2021-1243590B-I00/ERDF funded by MCIN/AEI//10.13039/501100011033 and by ERDF A way of making Europe). This project was also funded by Project 964562 (RISEUP), H2020 FetOpen program
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Tesis doctoral (DoctoralThesis)

Producción de planta injertada de vid en vivero: evaluación del impacto de las características de la madera, el tipo de injerto y su alineación sobre la tasa de éxito y la calidad de la planta

  • Villa Llop, Ana
El tutor en la empresa es Javier Eraso Zabalegui, El viverismo vitícola, inexistente antes de la crisis de la filoxera a finales del siglo XIX, se consolidó como un sector estratégico al imponerse la necesidad de injertar la vid europea (Vitis vinifera L.) sobre portainjertos americanos resistentes. Desde entonces, el viverismo constituye el primer eslabón de la cadena vitivinícola, garantizando la calidad, la sanidad y la adaptación de los viñedos a nuevas condiciones. Actualmente, el sector se enfrenta a retos relacionados con el éxito del injerto, la longevidad de los viñedos y la sostenibilidad del sistema de producción. Esta Tesis doctoral industrial, desarrollada en Vitis Navarra SAT en colaboración con la Universidad Pública de Navarra, aborda estos tres retos mediante una investigación aplicada en condiciones reales de vivero y viñedo. El primer reto, mejorar el éxito del injerto, se abordó caracterizando el material vegetal previo al injerto. Se analizaron parámetros anatómicos, fisiológicos y moleculares de madera de 110R procedente de distintos orígenes de producción, y se evaluó el papel de las reservas de carbohidratos en estacas de los portainjertos SO4 y 110 Richter y en púas de las variedades Merlot y Tempranillo, tanto en vivero como en condiciones de hidroponía. Además, se examinó el estado sanitario en seis campos madre (siete variedades y cinco portainjertos), con especial atención a la presencia de virosis secundarias. Los resultados mostraron que un exceso de almidón en la púa redujo el éxito del injerto y el crecimiento en vivero, y que la coinfección viral comprometió la viabilidad del proceso. El segundo reto, recuperar la longevidad de los viñedos, se investigó comparando cinco métodos de injerto (omega, V, hendidura, inglés mecanizado y manual) durante tres años en vivero y siete campañas en viñedo. También se evaluó la alineación vascular en injertos omega, tanto en campo (tres años) como en maceta bajo condiciones de estrés hídrico moderado, y se realizaron análisis histológicos y pruebas de conductividad hidráulica en los diferentes métodos y alineaciones. Los ensayos, realizados con Tempranillo sobre 110 Richter, confirmaron que la alineación correcta es clave para garantizar una unión anatómica e hidráulica funcional, y que el injerto en omega, cuando se ejecuta con precisión, ofrece altas tasas de éxito y plantas con buena calidad fisiológica. El tercer reto, avanzar hacia un viverismo más sostenible, se abordó mediante la evaluación de la productividad en tres sistemas de conducción en campos madre de 140 Ruggeri y 110 Richter. Los resultados indicaron que los sistemas verticales tuvieron un rendimiento inferior en número de estacas comparado con la cabeza de mimbrera, lo que evidencia la necesidad de equilibrar sostenibilidad y productividad., The grapevine nursery sector emerged after the phylloxera crisis in the late 19th century. At that time, European grapevine (Vitis vinifera L.) had to be grafted onto resistant American Vitis rootstocks to guarantee the continuity of vineyards. Since then, nurseries have become essential in the wine industry. They ensure the quality, sanitary status and adaptation of vineyards. Today, the sector faces three main challenges: grafting success, vineyard longevity and sustainable production. This industrial PhD Thesis, carried out at Vitis Navarra SAT in collaboration with the Public University of Navarre, addressed these challenges through applied research under real nursery and vineyard conditions. The first challenge, improving grafting success, was addressed by characterising plant material prior to grafting. Anatomical, physiological and molecular parameters were analysed in 110 Richter wood from different production origins, and the role of carbohydrate reserves was evaluated in canes of the rootstocks SO4 and 110R and in scions of the varieties Merlot and Tempranillo, both in the nursery and under hydroponic conditions. In addition, the sanitary status of propagation material was assessed in six mother fields (seven varieties and five rootstocks), with special attention to secondary viruses. Results showed that high starch content in the scion reduced grafting success and growth in the nursery, and that viral co-infections compromised plant viability. The second challenge, recovering vineyard longevity, was investigated by comparing five grafting methods (omega, V, full cleft, whip and tongue, mechanical and manual) over three years in the nursery and seven seasons in the vineyard. Vascular alignment in omega grafts was also evaluated, both in the vineyard (three years) and in pots under moderate water stress, and histological observations and hydraulic conductivity tests were conducted across the different methods and alignments. Trials performed with Tempranillo grafted onto 110 Richter confirmed that complete alignment is essential to ensure a functional anatomical and hydraulic union, and that correctly executed omega grafting ensures high success rates and vigorous plants. The third challenge, advancing towards more sustainable nursery practices, was addressed by evaluating productivity in three training systems in rootstock mother fields of 140 Ruggeri and 110R. Results showed that vertical systems produced fewer cuttings compared with the traditional “cabeza de mimbrera”, highlighting the need to balance sustainability and productivity., La realización de esta tesis doctoral industrial ha sido posible gracias a la concesión de una “Ayuda para la contratación de doctorandos y doctorandas por empresas, centro de investigación y centros tecnológicos: Doctorados industriales 2021” (convocatoria 2021) por parte del Gobierno de Navarra, Departamento de Universidad, Innovación y Transformación Digital a la empresa Vitis Navarra S.A.T. (Resolución 283E/2020; Número expediente: 0011-1408-2021-000028)., Programa de Doctorado en Biotecnología (RD 99/2011), Bioteknologiako Doktoretza Programa (ED 99/2011)
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Tesis doctoral (DoctoralThesis)

Comparative transcriptomics and functional analysis of lignocellulose decay pathways in White Rot and Brown Rot fungi of the Agaricomycetes class. A focus on Pleurotus ostreatus, Transcriptoma comparativo y análisis funcional de las vías de descomposición de la lignocelulosa en hongos de podredumbre blanca y podredumbre parda de la clase Agaricomycetos. Enfoque en Pleurotus ostreatus, Agaricomycetes klaseko eta lignozelulosaren deskonposaketan parte hartzen duten usteldura zuri- eta marroidun onddoen transkriptoma konparatibo eta analisi funtzionala Pleurotus ostreatus-en arreta jarriz

  • Jiménez Miguel, Idoia
Los hongos degradadores de madera son fundamentales para los ecosistemas forestales, ya que descomponen la lignocelulosa —la matriz de celulosa, hemicelulosa y lignina de las paredes celulares vegetales—. Este proceso recicla nutrientes, favorece el crecimiento de las plantas y tiene aplicaciones industriales en biocombustibles y bioproductos. Los Agaricomycetes emplean dos estrategias para degradar la lignocelulosa: los hongos de pudrición blanca (WRF) descomponen lignina y carbohidratos, logrando una degradación completa, mientras que los de pudrición parda (BRF) actúan sobre carbohidratos y dejan la lignina intacta. Este estudio compara tres WRF (Pleurotus ostreatus, Phanerochaete chrysosporium, Heterobasidion irregulare) y dos BRF (Fomitopsis schrenkii, Rhodonia placenta) mediante transcriptómica, análisis enzimático y perfilado metabólico en glucosa y madera. Los WRF mostraron una fuerte inducción de enzimas degradadoras de lignina, mientras que los BRF carecían de estos genes y dependían de una química oxidativa tipo Fenton con un repertorio limitado de celulasas. Las GH16 fueron la única familia enzimática sobreexpresada en todos los hongos cuando estos eran cultivados en madera, lo que resalta su papel conservado pero versátil en el metabolismo de los carbohidratos. En P. ostreatus, las monooxigenasas líticas de polisacáridos (LPMO) de la familia AA9 formaban un grupo numeroso y diverso, regulado por motivos promotores e influenciado por elementos transponibles cercanos, lo que sugiere una evolución dinámica y una regulación afinada. El análisis metabólico mostró que los WRF empleaban vías oxidativas robustas (glucólisis, PPP, ciclo del TCA y ciclo del glioxilato), lo que favorece una utilización eficiente del carbono. Los BRF preferían la oxidación parcial de azúcares y la fermentación, en consonancia con su modo de descomposición centrado en los carbohidratos. En resumen, este trabajo aclara las bases moleculares, enzimáticas y metabólicas de la descomposición de la madera por hongos. Revela las estrategias contrastantes entre WRF y BRF, el papel central y conservado de las enzimas GH16, la diversidad y regulación de las LPMO AA9, así como adaptaciones diferenciadas en el metabolismo del carbono. Estos hallazgos profundizan en la comprensión de la ecología fúngica y aportan un conocimiento valioso para la biotecnología y la conversión de biomasa., Egurraren degradatzaile diren onddoak funtsezko eragileak dira baso-ekosistemetan, lignozelulosa —zelulosa, hemizelulosa eta lignina— deskonposatuz mantenugaien zikloa ixteko eta karbonoaren fluxua erregulatzeko. Prozesu honek, gainera, bioerregai eta balio erantsi handiko bioproduktu berriztagarrien ekoizpenerako aukerak eskaintzen ditu. Agaricomycetes taldean bi usteltze-estrategia nagusi bereizten dira: usteldura zuriko onddoek (WRF) lignina eta karbohidratoak mineralizazio osoz degradatzen dituzte, eta usteldura marroikoek (BRF), aldiz, karbohidratoetan zentratzen dira, lignina ia osorik mantenduz. Lan honetan hiru WRF (Pleurotus ostreatus, Phanerochaete chrysosporium, Heterobasidion irregulare) eta bi BRF (Fomitopsis schrenkii, Rhodonia placenta) alderatu dira, glukosa eta egur baldintzetan egindako transkriptomika azterketen bidez, CAZy entzima-familien karakterizazioarekin eta bide metabolikoen analisi integratuekin osatuta. WRF espezieek entzima ligninolitikoen indukzio sendoa erakutsi zuten eta BRF espezieek, berriz, Fenton kimikarekin eta zelulasa multzo minimoarekin lotutako entzima oxidatiboen aktibazioa. Transkriptomak espezifikotasun handiko gene gutxi batzuen espresioaren menpe zeuden espezie guztietan. GH16 glukanasak gainespresatuta agertu ziren espezie guztietan egur baldintzetan, hemizelulosa eta β-glukanoen degradazioan duten funtzio kontserbatua nabarmenduz. P. ostreatusen AA9 LPMO familiak aniztasun handia erakutsi zuen, promotore-motibo espezifikoek eta elementu transposagarriek erregulatuta, malgutasun genomikoaren eta erregulazio-moduluen garrantzia azpimarratuz. Maila metabolikoan, WRF espezieek bide oxidatibo osoak aktibatu zituzten (glukolisia, PPP, TCA eta glioxilato-zikloa), eta BRF espezieek oxidazio partzial eta hartzidura-bideak lehenetsi zituzten. Oro har, ikerketa honek erakusten du WRF espezieek lignozelulosa osorik mineralizatzeko gaitasuna dutela, BRF espezieek, aldiz, energia azkar eskuratzeko bideak optimizatzen dituztela. GH16ren paper nagusia, AA9ren aniztasun funtzionala eta espezie bakoitzaren egokitzapen metabolikoak ekologia fungikoaren ulermena sakontzen dute eta lignozelulosaren balorizaziorako aplikazio bioteknologiko berrien garapenerako oinarriak eskaintzen dituzte., Wood-decaying fungi are key to forest ecosystems, breaking down lignocellulose—the cellulose, hemicellulose, and lignin matrix of plant cell walls. This process recycles nutrients, supports plant growth, and has industrial applications in biofuels and bioproducts. Agaricomycetes use two main decay strategies for lignocellulose degradation. White rot fungi (WRF) degrade lignin and carbohydrates, achieving complete lignocellulose breakdown, while brown rot fungi (BRF) mainly attack carbohydrates and leave lignin intact. This study compared three WRF (Pleurotus ostreatus, Phanerochaete chrysosporium, Heterobasidion irregulare) and two BRF (Fomitopsis schrenkii, Rhodonia placenta) through transcriptomics, enzyme family analysis, and metabolic profiling under glucose and wood growth conditions. WRF showed strong induction of lignin-degrading enzymes such as peroxidases and laccases, while BRF lacked these genes and relied on oxidative chemistry with limited cellulases. GH16 glucanases were the only enzyme family consistently upregulated across all fungi, highlighting their conserved but versatile role in carbohydrate metabolism. Enzyme repertoires were highly species-specific, with transcriptomes dominated by a few strongly expressed genes. In P. ostreatus, AA9 lytic polysaccharide monooxygenases (LPMOs) formed a large, diverse family regulated by promoter motifs and influenced by nearby transposable elements, suggesting dynamic evolution and fine-tuned control. Metabolic analysis showed that WRF used robust oxidative pathways (glycolysis, PPP, TCA cycle, glyoxylate shunt), supporting efficient carbon utilization. BRF favored partial sugar oxidation and fermentation, reflecting their carbohydrate-focused decay mode. These metabolic differences align with ecological strategies: WRF dismantle lignin-rich substrates, while BRF optimize rapid carbohydrate extraction. In summary, this work clarifies the molecular, enzymatic, and metabolic bases of fungal wood decay. It reveals contrasting strategies between WRF and BRF, the conserved central role of GH16 enzymes, the diversity and regulation of AA9 LPMOs, and distinct carbon metabolism adaptations. These insights advance understanding of fungal ecology and provide valuable knowledge for biotechnology and biomass conversion., Este trabajo ha sido financiado por el Plan Estatal de Investigación Científica del Ministerio de Ciencia, Innovación y Universidades H2020 MUSA 727624 (UE), RTI2018-099371-B-I00 (MCIN/AEI/10.13039/5011000110333 y FEDER Una manera de hacer Europa) (Hybdown), PID2023-152373OB-I00 (MCIN/AEI/10.13039/5011000110333 y FEDER Una manera de hacer Europa) (Funlip), por el Departamento de Industria del Gobierno de Navarra con el Proyecto 0011-1365-2024-000117 (Funginsect) y por el Departamento de Energía de los Estados Unidos de América (U.S. Department of Energy, DOE) asociado al Joint Genome Institute con la Propuesta: 10.46936/10.25585/60000628 de la Oficina de Instalaciones de Usuario de la Oficina de Ciencia del DOE, bajo el Contrato No. DE-AC02-05CH11231 y por los fondos de la Universidad Pública de Navarra (UPNA) concedidos al Grupo de Investigación en Genética, Genómica y Microbiología., Programa de Doctorado en Biotecnología (RD 99/2011), Bioteknologiako Doktoretza Programa (ED 99/2011)
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Tesis doctoral (DoctoralThesis)

Data transmission analysis and forecasting in industrial process environments, Análisis de transmisión de datos y predicción en entornos de procesos industriales

  • Miguélez García, Fernando
En los sistemas modernos basados en datos, disponer de una información actualizada es crucial para una toma de decisiones precisa y eficiente. La utilidad de los datos en entornos industriales, sistemas autónomos y redes de comunicación depende no sólo de su precisión, sino también de su actualidad. Esta tesis se basa precisamente en la idea de que los datos más recientes permiten tomar decisiones más fiables y eficaces, y explora este principio desde perspectivas tanto teóricas como aplicadas. Los principales objetivos son mejorar la comprensión teórica de cómo evoluciona el valor temporal de la información bajo diferentes restricciones prácticas y diseñar enfoques de modelización que aprovechen los datos recientes para mejorar la previsión y la toma de decisiones en entornos industriales reales. Tras una breve introducción en el Capítulo 1 describiendo los principales retos de esta tesis, el Capítulo 2 ofrece un breve repaso de algunos conceptos de probabilidad, procesos estocásticos y teoría de colas, así como la definición formal de AoI, una medida de lo reciente que es la información, y de los sistemas híbridos estocásticos, una herramienta matemática relevante en el estudio de sistemas dinámicos complejos. También presenta nociones básicas de la teoría de juegos, como el equilibrio de Nash y el precio de la anarquía, para analizar las interacciones estratégicas en sistemas competitivos, y explica los modelos ocultos de Markov (HMM) y su extensión a los HMM de entrada-salida, que constituyen la base de la metodología de predicción desarrollada más adelante. Estos conceptos proporcionan los fundamentos necesarios para el desarrollo de los siguientes capítulos. El primer objetivo se aborda en los Capítulos 3 y 4. El Capítulo 3, “Sobre la edad de la información en colas de un solo servidor con actualizaciones con edad”, amplía el marco AoI a sistemas en los que los paquetes pueden llegar ya con cierta antigüedad, como en las redes multisalto o de preprocesamiento. Se deriva una fórmula general para el AoI promedio que tiene en cuenta las correlaciones entre la edad inicial del paquete y el proceso entre salidas, y también se establecen cotas para los casos en los que se desconocen estas dependencias. La aplicabilidad de este enfoque se demuestra en diversos modelos de colas, incluyendo las retransmisiones en colas con pérdidas, colas en tándem y colas de reintentos. El Capítulo 4, “Precio de la anarquía con múltiples fuentes de información en competencia”, examina escenarios de canales compartidos modelados como juegos no cooperativos. Se demuestra que las estrategias de transmisión egoístas degradan el rendimiento en comparación con los óptimos cooperativos, y la ineficiencia se mide mediante el precio de la anarquía. Los resultados ponen de relieve las vulnerabilidades de los sistemas descentralizados y sugieren mecanismos de coordinación para reducir la pérdida de rendimiento. El segundo objetivo se aborda en el Capítulo 5, “Un enfoque de aprendizaje adaptativo para la predicción multivariante de tiempos en procesos industriales”, que propone un modelo de Markov oculto de entrada-salida con actualizaciones adaptativas de parámetros para explotar datos multivariantes recientes. Aplicado a conjuntos de datos industriales reales, alcanza una precisión competitiva frente a los modelos de referencia y permite la detección temprana de ineficiencias. La tesis finaliza con las principales conclusiones y las futuras líneas de investigación., In modern data-driven systems, the timeliness of information is crucial for accurate and efficient decision-making. The usefulness of data in industrial environments, autonomous systems, and communication networks depends not only on its accuracy but also on its freshness. This thesis is motivated precisely by the idea that more recent data enables more reliable and effective decisions, and explores this principle from both theoretical and applied perspectives. The main goals are to improve the theoretical understanding of how information freshness behaves under different practical constraints and to design modelling approaches that leverage recent data to enhance forecasting and decision-making in real-world industrial settings. After a brief introduction describing the main challenges of this dissertation in Chapter 1, Chapter 2 provides a concise overview of probability, stochastic processes, and queueing theory, as well as the formal definition of the Age of Information (AoI), a metric that quantifies the information timeliness, and stochastic hybrid systems, a mathematical tool relevant for the study of complex dynamic systems. It also introduces basic notions of game theory, including Nash equilibrium and Price of Anarchy, for analysing strategic interactions in shared systems, and presents hidden Markov models (HMMs) and their extension to input-output HMMs, which form the basis for the forecasting methodology developed later. These concepts provide the necessary background for the developments in the following chapters. The first main objective of the thesis is addressed in Chapters 3 and 4. Chapter 3, “On the Age of Information in Single-Server Queues with Aged Updates”, extends the AoI framework to systems where packets may arrive already aged, as in multi-hop or pre-processing networks. A general formula for the average AoI is derived, accounting for correlations between initial packet age and inter-departure process, with bounds for cases where these dependencies are unknown. The applicability of the framework is demonstrated in various queueing settings, including retransmissions in lossy queues, tandem queues, and retrial queues. Chapter 4, “Price of Anarchy with Multiple Information Sources under Competition”, examines shared-channel scenarios modelled as non-cooperative games. Selfish transmission strategies are shown to degrade performance compared with cooperative optima, with inefficiency measured by the Price of Anarchy. Results highlight vulnerabilities of decentralised systems and suggest coordination mechanisms to reduce performance loss. The second main objective of this thesis is addressed in Chapter 5, “An Adaptive Learning Approach to Multivariate Time Forecasting in Industrial Processes”, which proposes an input-output hidden Markov model with adaptive parameter updates to exploit fresh, multivariate data. Applied to real industrial datasets, it achieves competitive accuracy against benchmarks and supports early detection of inefficiencies. The dissertation ends with the main conclusions and future research directions., This thesis has been supported by project SMART ZEO 0011-1365-2021-000085, project PDC2021-120796-I00/MCIN/AEI/10.13039/501100011033, project PID2020- 113125RB-I00/MCIN/AEI/10.13039/501100011033, and by the financial assistance granted by CNRS-IRIT., Programa de Doctorado en Matemáticas y Estadística (RD 99/2011), Matematikako eta Estatistikako Doktoretza Programa (ED 99/2011)
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Tesis doctoral (DoctoralThesis)

Optimización energética de muebles de refrigerados y congelados mediante estudio computacional y experimental de nuevas configuraciones de funcionamiento

  • Soto Armendariz, Ricardo
El incremento de las emisiones de gases de efecto invernadero, derivados del aumento de la demanda energética, ha provocado la implementación de políticas internacionales, cuyos objetivos tratan de afrontar problemas como la contaminación, las emisiones de CO2 o el incremento de la temperatura media global. En este contexto, el sector de la refrigeración comercial destaca por su elevado impacto, al representar alrededor del 20 % del consumo eléctrico mundial. Dentro de dicho sector, se encuentra la conservación de alimentos en supermercados, que, debido al funcionamiento continuo de los muebles, es responsable del 2.51 % del consumo nacional. Por ello, las normativas aplicables a dicho sector se han vuelto cada vez más restrictivas en cuanto a eficiencia energética, obligando a migrar hacia soluciones de muebles con menores consumos, con el objetivo de reducir las emisiones y limitar el ritmo de aumento de la temperatura media global. Tras revisar la literatura científica disponible, se ha detectado que los esfuerzos se han destinado históricamente a la optimización de muebles verticales. Por esta razón, la presente tesis doctoral aporta su granito de arena al desarrollar una metodología de optimización de muebles horizontales con función de venta directa basada en el desarrollo de modelos de Dinámica de Fluidos Computacional (CFD), en la que se analiza del comportamiento termo-fluidodinámico de los muebles, demostrando el potencial de mejora energética y térmica de estos equipos. Los desarrollos constan de modelos bidimensionales en régimen estacionario validados experimentalmente, capaces de reproducir la distribución de temperaturas en los paquetes de ensayo, y la distribución de velocidades y temperaturas del aire. Tanto los ensayos experimentales como los modelos CFD suministran información sobre los fenómenos que causan las ineficiencias energéticas del sistema, como son las infiltraciones de aire caliente del ambiente, las fugas de aire frío del interior del mueble, las turbulencias, o las pérdidas de presión en los conductos y rejillas. Analizando la ubicación y la causa de dichos fenómenos, se plantean modificaciones geométricas que interfieren en la distribución de temperaturas y velocidades, reduciendo las necesidades frigoríficas del sistema, a la vez que disminuye la temperatura del paquete caliente crítico y se mejora la uniformidad térmica del mueble. En función de la optimización planteada en los modelos CFD, se pueden alcanzar reducciones de potencia teóricas del 15.76 % en el mejor de los casos, así como descensos teóricos en la temperatura de los paquetes críticos de 1.56 ℃. Al evaluar experimentalmente algunas de las soluciones planteadas computacionalmente, se obtienen resultados similares, con reducciones del 16.10 % en el consumo energético del mueble, y reducciones de 0.78 ℃ en la temperatura del paquete caliente crítico. Estos resultados, han permitido reducir un nivel el etiquetado energético de los muebles estudiados. Un aspecto adicional por destacar es que la disminución de la temperatura máxima de los paquetes permite elevar la temperatura de evaporación sin rebasar los límites normativos asociados a la clasificación de los muebles según la temperatura del producto almacenado. Este planteamiento contribuye a obtener ahorros energéticos adicionales y posibilita un funcionamiento optimizado del ciclo frigorífico. En términos generales, los resultados muestran que los muebles horizontales cuentan con un importante potencial de mejora, tanto desde el punto de vista térmico como energético. Esto deriva en menores consumos energéticos, reducciones de la clase climática y mejoras en el etiquetado energético. Desde la perspectiva industrial, la metodología desarrollada se perfila como una herramienta eficaz para reducir los tiempos y costes vinculados al prototipado y a los ensayos experimentales, facilitando la toma de decisiones de diseño y acelerando la implantación de soluciones más eficientes en el mercado. Asimismo, las conclusiones de esta tesis doctoral evidencian que la dinámica de fluidos computacional resulta fundamental para la optimización de armarios con función de venta directa. Su aplicación, apoyada en criterios de diseño geométrico que influyen en la distribución de velocidades y temperaturas, tiene un impacto directo en la mejora de la eficiencia energética de los sistemas y del sector en última instancia., The increase in greenhouse gas emissions, resulting from the rise in energy demand, has led to the implementation of international policies aimed at addressing issues such as pollution, CO₂ emissions, and the increase in average global temperature. In this context, the commercial refrigeration sector stands out due to its significant impact, accounting for around 20 % of global electricity consumption. Within this sector, food preservation in supermarkets is particularly relevant since, due to the continuous operation of display cabinets, it is responsible for 2.51 % of national energy consumption. Therefore, the regulations applicable to this sector have become increasingly restrictive regarding energy consumption, forcing a shift toward more efficient display cabinet solutions in order to reduce emissions and limit the rate of increase in average global temperature. After reviewing the scientific literature, it has been found that efforts have historically been focused on optimizing vertical display cabinets. For this reason, this PhD contributes by developing an optimization methodology for horizontal display cabinets with direct sales function, based on the development of Computational Fluid Dynamics (CFD) models. These models analyze the thermo-fluid dynamic behavior of the cabinets, demonstrating their potential for energy and thermal improvement. The developments consist of two-dimensional steady-state models validated experimentally, capable of reproducing the temperature distribution within the test packages, as well as the air velocity and temperature distributions. Both the experimental tests and the CFD models provide information about the phenomena that cause energy inefficiencies, such as the infiltration of warm ambient air, cold air leakage, as well as turbulence and pressure losses in ducts and grilles. By analyzing the location and causes of these phenomena, geometric modifications are proposed that affect the distribution of temperatures and velocities, reducing the system’s refrigeration demand while lowering the temperature of the critical warm package and improving the thermal uniformity of the cabinet. Depending on the optimization proposed in the CFD models, theoretical power reductions of up to 15.76 % can be achieved in the best case, along with theoretical decreases of 1.56 ℃ in the temperature of the critical packages. When some of the computationally proposed solutions are experimentally evaluated, similar results are obtained, with reductions of 16.10 % in the cabinet’s energy consumption and decreases of 0.78 ℃ in the temperature of the critical warm package. These results have made it possible to improve the energy labeling of the studied cabinets by one level. the packages allows for an increase in the evaporation temperature without exceeding the regulatory limits associated with the classification of cabinets according to the temperature of the stored product. This approach contributes to additional energy savings and enables more optimized operation of the refrigeration cycle. In general terms, the results show that horizontal display cabinets have significant potential for improvement, both from a thermal and an energy perspective. This can lead to lower energy consumption, reductions in climate class, and improvements in energy labeling. From an industrial perspective, the developed methodology emerges as an effective tool to reduce the time and costs associated with prototyping and experimental testing, facilitating design decision-making and accelerating the implementation of more efficient solutions in the market. Furthermore, the conclusions of PhD demonstrate that computational fluid dynamics plays a key role in optimizing cabinets intended for direct sales. Its application, supported by geometric design criteria that influence the distribution of velocities and temperatures, has a direct impact on improving the energy efficiency of both the system and the sector., Gobierno de Navarra, mediante la convocatoria “Ayudas para la contratación de doctorandos y doctorandas: Doctorados industriales 2023", con Nº de expediente 0011-1408- 2023-000001., Programa de Doctorado en Tecnologías de las Comunicaciones, Bioingeniería y de las Energías Renovables, Bioingeniaritzako eta Komunikazioen eta Energia Berriztagarrien Teknologietako Doktoretza Programa Ofiziala
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Tesis doctoral (DoctoralThesis)

Subproductos vegetales en la alimentación de rumiantes: evaluación nutricional e inclusión en una ración alternativa para vacuno de cebo, efecto sobre el rendimiento productivo, la calidad de la canal y de la carne y la sostenibilidad ambiental

  • Goenaga Uceda, Irantzu
La producción ganadera desempeña un papel fundamental en la seguridad alimentaria global y la gestión responsable del medio ambiente. Los productos de origen animal asociados a la producción de rumiantes, son esenciales en la provisión de alimentos de alta calidad nutricional en la dieta humana. El aumento previsto de la población mundial, junto con la creciente preocupación por el impacto ambiental de la actividad ganadera, requieren una estrategia global que promueva un sistema de producción más eficiente, resiliente y sostenible. En este contexto, la incorporación de subproductos de la industria agroalimentaria a la alimentación de rumiantes presenta un gran potencial. El empleo de estos materiales proporciona ingredientes de proximidad y reduce la dependencia en el uso de otras materias primas, que requieren un elevado volumen de tierra cultivable y una cantidad apreciable de insumos. Es necesario desarrollar estrategias de alimentación alternativas que puedan ser aplicadas en la producción de rumiantes, con el objetivo de optimizar el aprovechamiento de los recursos naturales dentro del modelo productivo y de responder a la demanda actual de los consumidores, sobre la obtención de productos de origen animal seguros, saludables y producidos bajo criterios de mayor sostenibilidad. El objetivo general de esta Tesis Doctoral ha sido comparar el efecto de la alimentación en base a la utilización de subproductos vegetales respecto a una dieta convencional en la producción de carne de ternera, a través de técnicas in vitro e in vivo. Aunque valorizar los subproductos vegetales en la nutrición animal representa una oportunidad, la literatura científica disponible sobre la incorporación de los mismos en raciones de animales es limitada, y existe una notable falta de estudios que relacionen el uso de los mismos con el rendimiento de producción y la calidad de la carne, especialmente en ganado bovino. Por ello, la información generada en este trabajo, facilitará la inclusión de los subproductos vegetales en las dietas para rumiantes y ayudará a conocer el efecto de su aplicación en una dieta para ganado vacuno de cebo, respecto a una dieta convencional. Los resultados obtenidos en esta Tesis Doctoral indican el potencial de los subproductos vegetales generados en la industria agroalimentaria para la alimentación animal, debido a sus características nutricionales. A través de una correcta gestión, la utilización de los mismos en dietas para rumiantes podría reemplazar parcialmente a otros ingredientes convencionales, utilizados como fuente de energía, fibra o proteína. El empleo de los subproductos vegetales estudiados en una ración completa ensilada para el vacuno de cebo, ofrece la posibilidad de obtener una carne de calidad análoga a la procedente mediante la alimentación convencional. A pesar de ciertas disminuciones en el rendimiento animal, se alcanzan mejoras en cuanto al perfil nutricional de la grasa de la carne y a su calidad sensorial. De esta manera, se consigue una mayor sostenibilidad en el sistema de producción ganadera, pudiendo reducir la componente azul de la huella hídrica y la huella de carbono. Estos resultados contribuyen a ampliar el conocimiento sobre el efecto de la inclusión de los subproductos vegetales en raciones para ganado bovino, constituyendo una base útil para futuras investigaciones. Esta línea de trabajo, permitirá optimizar el uso de recursos disponibles localmente y promover la economía circular entre dos sectores estratégicos, como son la industria agroalimentaria y la producción ganadera, contribuyendo así a mejorar la sostenibilidad del sistema agroalimentario., Ayudas para la contratación de doctorandos y doctorandas por empresas, centros de investigación y centros tecnológicos: Doctorados industriales 2020. Gobierno de Navarra. Nº de expediente: 0011-1408-2020-000009., Programa de Doctorado en Agroalimentación (RD 99/2011), Nekazaritzako Elikagaietako Doktoretza Programa (ED 99/2011)
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Tesis doctoral (DoctoralThesis)

Characterisation of Huntington disease in the Spanish population: an epidemiological and molecular study of the HTT gene variability and CAG repeat somatic instability

  • Ruiz de Sabando, Ainara
El objetivo de esta tesis doctoral es describir la enfermedad rara, neurodegenerativa y autosómica dominante, conocida como enfermedad de Huntington (EH) en la población española. Para ello, estudiamos la epidemiología de la enfermedad, las características moleculares del gen de la EH (HTT) y la inestabilidad somática de las repeticiones de CAG, analizando su potencial efecto modificador del fenotipo clínico en portadores de alelos intermedios (AIs). Para el estudio epidemiológico, se identificaron casos con EH a través del Registro de Enfermedades Raras y del centro de Genética Médica de referencia de Navarra, estimándose la tasa de prevalencia con fecha 31 de diciembre de 2017, y las de incidencia y mortalidad, para un período de 27 años (1991-2017). La diversidad genética del gen HTT se analizó mediante el genotipado de SNPs y una secuenciación profunda del exón uno, en dos grandes cohortes nacionales: una muestra de controles poblacionales (n=520) y otra de familias con individuos sintomáticos (n=471), remitidos para diagnóstico genético de EH, incluyendo 331 sujetos índices con EH y 140 portadores de AIs (27-35 CAG repeticiones). También se recogieron los datos clínicos y las historias familiares disponibles, en base a lo cual los portadores de AIs se clasificaron en sintomáticos o controles de la población general. Se estudió la inestabilidad somática en sangre de individuos portadores de alelos de ≥27 CAGs, así como la posible asociación de las expansiones somáticas con la presencia de signos neurocognitivos en portadores de AIs (53 controles y 82 sintomáticos, incluyendo muestras de tejido cerebral de un paciente sintomático, portador de 33 CAGs). La prevalencia de EH en Navarra, en diciembre de 2017, fue de 4,94 (IC del 95%: 3,23, 6,65) por 100.000, con un aumento anual del 6,1% desde 1991 hasta 1999. Las tendencias de incidencia y mortalidad se mantuvieron estables desde 1995-96, con tasas medias anuales por 100.000 de 0,36 (IC del 95%: 0,27, 0,47) y 0,23 (IC del 95%: 0,16, 0,32), respectivamente. Las edades medias de inicio de síntomas y de fallecimiento en individuos EH fueron de 49.6 ± 18.8 y 66.6 ± 17.1 años, respectivamente, con una duración media de la enfermedad de 16.7 ± 8.1 años. El estudio molecular del gen HTT reveló que los alelos de <27 CAGs de la población española tienen una mayor proporción de haplotipos C (40,1%), mientras que el A1 (39,8%) y A2 (31,6%) predominan entre los alelos intermedios y expandidos, respectivamente. Los alelos de ≥50 CAGs están asociados principalmente a los haplotipos A2 (38,9%) y C (32%), también presentes en el 50% y el 21,4%, respectivamente, de familias EH con grandes expansiones intergeneracionales. La deleción de CAACAG en el exón uno del gen HTT se asocia con el haplotipo C y parece correlacionarse con mayores expansiones intergeneracionales y un inicio temprano de los síntomas. El fenotipo de portadores de AIs se caracterizó por signos motores (84%), cognitivos (29%) y/o conductuales (28%), con una edad tardía de comienzo de los síntomas (58.7 ± 18.6 años), sin correlación con la longitud de CAGs. Los AIs presentan expansiones somáticas dependientes del nº de CAG y de la edad, con un 0,4% y un 0,01% de moléculas de ADN que se expanden por cada CAG y año, respectivamente. Los portadores sintomáticos de AIs no presentaban una inestabilidad somática estadísticamente diferente a la de los controles de la población general (p=0,066). Se detectaron expansiones somáticas de +1 y +2 CAGs en el cerebro del paciente con 33 CAGs, presentes con la mayor proporción en el putamen (10.3%) y la menor en el cerebelo (4.8%). En conclusión, las estimaciones epidemiológicas de la EH en nuestra población están dentro del rango de las del sur de Europa y no experimentaron variaciones temporales reales durante el periodo de estudio. Los haplotipos de alelos EH españoles se caracterizan por una alta diversidad genética, posiblemente secundaria a la mezcla con otras poblaciones no caucásicas, con una representación más alta de los haplotipos A2 y C que en la mayoría de poblaciones europeas. Las diferencias en las distribuciones de haplotipos entre los distintos rangos de CAGs apoyan la existencia de distintos mecanismos de expansión germinal, siendo los haplotipos A2 y C los que muestran las mayores expansiones intergeneracionales, posiblemente influenciados por elementos cis específicos, como la deleción CAACAG. Las expansiones somáticas de repeticiones CAG siguen una correlación gradual con la longitud de CAGs, que afecta tanto a los alelos expandidos como a los intermedios, siendo, además, edad y tejido dependientes; pero no parecen ser un factor desencadenante de un fenotipo neurocognitivo asociado en portadores de AIs. Es posible, sin embargo, que algunos AIs del gen HTT, especialmente aquellos cercanos al umbral patológico, con determinadas características de susceptibilidad genética, puedan manifestar un fenotipo neurológico compatible con la EH., The aim of this doctoral thesis is to study the epidemiology and the genetic background of the rare and autosomal dominant neurodegenerative disorder of Huntington disease (HD) in the Spanish population. We study the patterns of frequency, distribution and magnitude of the disease, the molecular characteristics of the HD gene (HTT) and the somatic instability of the CAG repeat sequence as a potential modifying factor of the clinical phenotype in intermediate alleles (IAs). For the epidemiologic study, HD cases were ascertained through the Rare Disease Registry and the reference Medical Genetics Centre of Navarra; incidence and mortality rates were estimated for a 27-year period (1991-2017) and prevalence was calculated for December 31st, 2017. HTT diversity was examined by SNP genotyping and deep sequencing analysis of exon one, in two large nationwide cohorts: a population-based control sample (n=520), and 471 families with symptomatic individuals referred for HD genetic testing, which included 331 index HD cases and 140 index IA carriers (27-35 CAG repeats). Clinical and family history data were obtained when available and IA carriers were further classified as symptomatic or population control subjects. Somatic instability of the HTT-CAG repeat sequence was studied in blood DNA samples of individuals with ≥27 CAG repeats. We further analysed the potential association of somatic expansions with neurocognitive signs in IA carriers (53 population controls and 82 symptomatic subjects, including brain tissues of a symptomatic 33 CAG allele carrier). The HD prevalence in Navarra, in December 2017, was 4.94 (95% CI: 3.23, 6.65) per 100,000, with an annual 6.1% increase from 1991 to 1999. Incidence and mortality trends remained stable since 1995-96, with mean annual rates per 100,000 of 0.36 (95% CI: 0.27, 0.47) and 0.23 (95% CI: 0.16, 0.32), respectively. The mean age at onset and death of HD patients was 49.6 ± 18.8 and 66.6 ± 17.1 years, respectively, with an average duration of disease of 16.7 ± 8.1 years. The HTT molecular study revealed that Spanish normal alleles (<27 CAGs) are enriched in C haplotypes (40.1%), while A1 (39.8%) and A2 (31.6%) prevail among intermediate and expanded chromosomes, respectively. Alleles of ≥50 CAG repeats are primarily associated with haplotypes A2 (38.9%) and C (32%), which are also present in 50% and 21.4%, respectively, of HD families with large intergenerational expansions. The deletion of CAACAG in HTT exon one is associated with haplotype C and appears to correlate with larger intergenerational expansions and early onset of symptoms. The phenotype of IA carriers was characterised by motor (84%), cognitive (29%) and/or behavioural (28%) signs, with a late age at onset (58.7 ± 18.6 years) that was not inversely correlated with the CAG length. IAs present somatic expansions that are CAG- and agedependent, with 0.4% and 0.01% of DNA molecules expanding by CAG and year, respectively. Somatic instability was not statistically different in symptomatic vs population control IA carriers (p=0.066). Somatic expansions of +1 and +2 CAGs were detected in brain tissues of the individual with 33 CAGs, with the highest ratio in the putamen (10.3% of the DNA molecules) and the lowest in the cerebellum (4.8%). In conclusion, HD epidemiological estimates observed in our population are within the Southern European countries range, and they did not experience true temporary variations over the last decades of post-molecular testing. Spanish HD haplotypes are characterised by a high genetic diversity, potentially admixed with other non-Caucasian populations, with a higher representation of A2 and C haplotypes than most European populations. Differences in haplotype distributions across the CAG length range support differential germline expansion dynamics, with A2 and C showing the largest intergenerational expansions, possibly under the effect of specific cis-elements such as the CAACAG deletion. Somatic CAG expansions follow a gradual CAG correlation, ranging from expanded to intermediate alleles, in an age and tissue-dependent manner, but they do not seem to be a major triggering factor of an associated neurocognitive phenotype in IA carriers. However, it might be posible that some HTT IAs, especially those close to the pathological threshold with a predisposing background, may manifest with an HD-like phenotype., This thesis has been supported by a fellowship of Departamento de Salud, Gobierno de Navarra (Resolución 1400E/2018, ref. 0011-4809-2018-000001). Additional funding that has enabled this work has come from Instituto de Salud Carlos III (grant no. FIS PI15/02227), and the CHDI Foundation (Enroll-HD study). The international doctoral stay was supported by Universidad Pública de Navarra (UPNA)., Programa de Doctorado en Ciencias de la Salud (RD 99/2011), Osasun Zientzietako Doktoretza Programa (ED 99/2011)
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Tesis doctoral (DoctoralThesis)

Desarrollo de receptores solares volumétricos activos de elevadas prestaciones para centrales termoeléctricas deconcentración en torre

  • Rández Diago, Xabier
Como se ha comentado previamente, en el Capítulo 4 se ha desarrollado un modelo CFD del prototipo ensayado en el banco de ensayos. El objetivo de este modelo es reproducir las condiciones de flujo y radiación otorgadas por el banco de ensayos para validar los resultados del mismo. Una vez se validó el modelo, se pudieron obtener detalles del comportamiento térmico y fluido-dinámico del receptor. Además, la validación del modelo CFD permitió durante el capítulo 6 reproducir las condiciones de radiación homogéneas presentes en una central CSP real para estimar su rendimiento térmico en condiciones nominales de trabajo y su efecto en una central CSP.Además del comportamiento térmico del receptor, es importante asegurar su integridad estructural de este ante las condiciones de trabajo a las que se podría enfrentar durante su vida útil. Para ello, a lo largo del Capítulo 5 se ha desarrollado el estudio del comportamiento termo mecánico del receptor desde el punto de vista de la mecánica de la fractura. Se ha caracterizado el carburo de silicio, material del receptor, para alimentar un modelo FEM con el que se ha estudiado la expansión de las micro-grietas debido a las tensiones inducidas por los gradientes de tensiones producidos por la temperatura. Este estudio ha arrojado resultados prometedores en cuanto a la vida útil de los discos del receptor para todos los tamaños de disco estudiados, asegurando su durabilidad en su uso en planta y demostrando la viabilidad estructural del concepto. Una vez demostrado el concepto de manera térmica (en los capítulos 3 y 4) y mecánica (en el Capítulo 5), con el fin de comprobar si este concepto mejora en algo a la tecnología actual de receptores volumétricos de aire, durante el Capítulo 6 se ha estudiado mediante el modelo CFD validado previamente, el rendimiento térmico del receptor frente a condiciones de radiación iguales a las de planta (radiación homogénea de hasta 1000 kW/m2) y su efecto en la energía producida y en el coste de la energía en dos configuraciones de central CSP de torre. Los resultados mostrados en este capítulo muestran mejoras en el rendimiento térmico del receptor de más de 0.1, es decir, un 10%, a 750°C.Por último, en el Capítulo 7 se desarrollan las conclusiones generales de la tesis, muy positivas en términos de avance de la tecnología, debido a la innovación del concepto, y en términos de comportamiento térmico de este nuevo concepto. Además, también se han desarrollado las líneas futuras necesarias hasta el desarrollo final de un receptor basado en el concepto de discos., Electricity production from solar thermal power, also called concentrated solar power (CSP), is a renewable generation technology with great potential, as it directly uses solar radiation that reaches the earth's crust. Approximately this solar power provides a total of 85 Peta Watts (85x1015 W), which can be used by terrestrial solar collectors to generate electricity or energy for high-temperature processes. This amount of power is 5000 times higher than the current global energy consumption, which is more than 15 Tera Watts (15x1012 W). In addition to this, CSP technology is able to manage the energy it generates and discharges to the grid, which is an important advantage over other renewable technologies such as wind and photovoltaics, either through thermal storage or hybridization with photovoltaics. Concentrating solar power plants collect the direct solar radiation (direct normal irradiation or DNI) that reaches the earth's surface and redirect it by concentrating it on a receiving surface through which a fluid circulates, absorbing this energy. They transform the energy from solar radiation first into thermal energy and then into mechanical work and electricity through a power cycle. As the element that transforms radiation into thermal energy, the receiver is one of the crucial elements of the plant to achieve high performance and increase the profitability of this type of technology. Moreover, the designs used today do not differ much from those used in the early days as far as air receivers are concerned. Due to the key importance of this element and the little evolution in its development, this thesis has focused on the design and characterization of an air receiver that provides an evolution in this technology. In this work we have developed the design, analysis and experimentation of an innovative receiver geometry and design with the aim that this technology achieves improvements in the thermal efficiency of the receiver as well as improvements from the point of view of durability that make solar thermal plants more competitive in the current electricity market. Thus, the work of this thesis has been structured in 4 blocks corresponding to chapters 3 to 7. The first work of this thesis, contained in Chapter 3, is focused on the explanation of the concept of rotating disks on which the receiver is based and on the experimentation, by means of a prototype at laboratory scale, of this receiver in a test bench prepared for this thesis. The results obtained from this experimentation have served to validate the results obtained from the CFD model of the receiver developed in Chapter 4. Furthermore, with this experimentation, the operation and feasibility of the concept in a controlled, small-scale environment has also been demonstrated at operating temperatures of almost 700°C. As previously mentioned, a CFD model of the prototype tested on the test bench has been developed in Chapter 4. The objective of this model is to reproduce the flow and radiation conditions provided by the test rig in order to validate the results of the model. Once the model was validated, details of the thermal and fluid-dynamic behaviour of the receiver could be obtained. In addition, the validation of the CFD model allowed during Chapter 6 to reproduce the homogeneous radiation conditions present in a real CSP plant to estimate its thermal performance under nominal working conditions and its effect on a CSP plant. In addition to the thermal performance of the receiver, it is important to ensure its structural integrity under the operating conditions that it could face during its working life. To this end, throughout Chapter 5, the study of the thermo-mechanical behaviour of the receiver from the point of view of fracture mechanics has been developed. For this purpose, silicon carbide, the receiver material, has been characterized to feed a FEM model with which the expansion of the micro-cracks due to the stresses induced by the stress gradients produced by the temperature have been studied. This study has yielded promising results in terms of the lifetime of the receiver discs for all the disc sizes studied, ensuring their durability in plant use and demonstrating the structural feasibility of the concept. After demonstrating the concept thermally (in chapters 3 and 4) and mechanically (in Chapter 5), in order to check if this concept is an improvement over current volumetric air receiver technology, during Chapter 6 the thermal performance of the receiver under plant radiation conditions (homogeneous radiation up to 1000 kW/m2) and its effect on the energy produced and the cost of energy in two tower CSP plant configurations were studied using the previously validated CFD model. The results shown in this chapter demonstrate improvements in receiver thermal performance of more than 0.1, a 10%, at 750°C. Finally, Chapter 7 develops the overall conclusions of the thesis, which are very positive in terms of technology advancement, due to the innovation of the concept, and in terms of thermal performance of this new concept. In addition, the necessary future lines have also been developed until the final development of a receiver based on the concept of disks., Gobierno de Navarra, beca obtenida para el desarrollo de la presente tesis doctoral con el número de adjudicación 0011-1408-2017-000016., Programa de Doctorado en Tecnologías de las Comunicaciones, Bioingeniería y de las Energías Renovables (RD 99/2011), Bioingeniaritzako eta Komunikazioen eta Energia Berriztagarrien Teknologietako Doktoretza Programa (ED 99/2011)
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Tesis doctoral (DoctoralThesis)

Decoding molecular olfactory alterations in neurodegeneration: sex differences and drug repurposing strategies in Alzheimer’s and Parkinson’s diseases

  • Cartas Cejudo, Paz
La disfunción olfativa es una característica temprana y común de las enfermedades neurodegenerativas (EN), particularmente de la enfermedad de Alzheimer (EA) y la enfermedad de Parkinson (EP), donde los cambios patológicos en las regiones de procesamiento olfativo, como el tracto olfativo (TO), contribuyen a los déficits en el sentido del olfato. Esta tesis tiene como objetivo explorar los mecanismos moleculares subyacentes a estos trastornos, utilizando proteómica de alto rendimiento para analizar muestras post-mortem del TO de sujetos con EA, EP y controles. El análisis de expresión proteica diferencial reveló alteraciones proteómicas significativas tanto en la EA como en la EP, con variaciones dependientes del sexo observadas, particularmente en la expresión de sirtuinas (SIRTs). De manera notable, las mujeres mostraron una disfunción proteómica más grave en comparación con los hombres, independientemente de la enfermedad, con patrones alterados de acetilación de proteínas en regiones olfativas clave en el cerebro. Además, establecimos un flujo de trabajo utilizando firmas ómicas olfativas y del tronco encefálico en un enfoque computacional, Connectivity Map (CMap), con el objetivo de obtener posibles dianas para el reposicionamiento de fármacos en EA y EP. Además, varias clases farmacológicas parecían ser candidatas potenciales para restaurar las firmas ómicas alteradas. La validación in vitro confirma que varios de los inhibidores propuestos ejercieron efectos neuroprotectores, reduciendo el daño por estímulos neuropatológicos y la toxicidad por estrés oxidativo. Estos hallazgos subrayan el valor de la proteómica olfativa para entender los mecanismos moleculares específicos del sexo en la EA y la EP, y sugieren que las firmas ómicas podrían servir como plantilla para desarrollar nuevas estrategias terapéuticas frente a los síndromes neurológicos., Olfactory dysfunction is an early and common feature of neurodegenerative diseases (NDs), particularly Alzheimer’s disease (AD) and Parkinson’s disease (PD), where pathological changes in olfactory processing regions, such as the olfactory tract (OT) contribute to deficits in smell. This thesis aimed to explore the molecular mechanisms underlying these impairments, using high-throughput proteomics to analyze post-mortem OT samples from AD, PD, and control subjects. Differential protein expression analysis revealed significant proteomic alterations in both AD and PD, with sex-dependent variations observed, particularly in the expression of sirtuins (SIRTs). Notably women showed more severe proteomic dysregulation compared to men, regardless of the disease, with altered protein acetylation patterns in key olfactory brain regions. Moreover, we established a workflow using olfactory and brainstem omics signatures in a computational approach, Connectivity Map (CMap), with the aim of obtaining potential targets for drug repurposing in AD and PD. Furthermore, various pharmacological classes seemed to be potential candidates to restore disrupted omics signatures. In vitro validation confirmed that several of the proposed inhibitors exerted neuroprotective effects, reducing damage from neuropathological insults and oxidative stress toxicity. These findings underscore the value of olfactory proteomics in understanding sex-specific molecular mechanisms in AD and PD and suggest that omics signatures could serve as a template for developing novel therapeutic strategies against neurological syndromes., Ayudas y financiaciones que han permitido el desarrollo de esta tesis: Referencia: 0011-1411-2020-000028. Entidad: Departamento de Desarrollo Económico y Empresarial (Estratégicos S3) del Gobierno de Navarra. Convocatoria 2020 de ayudas a proyectos estratégicos de I+D. Título: INNOLFACT. Implementación de medicina de precisión olfatoria y desarrollo de terapias nasales inmunomoduladores en envejecimiento y neurodegeneración. Duración: 2020-2022; Referencia: 0011-1411-2023-000028. Entidad: Departamento de Desarrollo Económico y Empresarial (Estratégicos S4) del Gobierno de Navarra. Convocatoria 2023-2026 de ayudas a proyectos estratégicos de I+D. Título: INNOLFACT 2.0: Combinación de Inteligencia Artificial y Reposicionamiento de Fármacos en Medicina de Precisión Olfatoria Duración: 2023-2025; Referencia: PID2023-152593OB-I00. Entidad: AEI. Proyectos de Generación de Conocimiento» del Programa Estatal para Impulsar la Investigación Científico-Técnica y su Transferencia, en el marco del Plan Estatal de Investigación Científica, Técnica y de Innovación 2021-2023. Título: INTERFERENCIA ENTRE LA ACETILACION Y LA FOSFORILACION EN LA ENFERMEDAD DE ALZHEIMER: PAPEL DE LAS SIRTUINAS 3 Y 7 EN NEURODEGENERACION OLFATORIA., Programa de Doctorado en Ciencias de la Salud (RD 99/2011), Osasun Zientzietako Doktoretza Programa (ED 99/2011)
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Tesis doctoral (DoctoralThesis)

Micellar casein concentrates and isolates: changes induced by stabilization and preservation methods

  • García Amezketa, Arantza
El uso de concentrados proteínas lácteas como ingredientes alimentarios va en aumento debido a su alto valor nutricional y funcional. Una buena estrategia para la obtención de estos concentrados es la filtración por membranas, ya que permite separar y concentrar componentes concretos de la leche, pero manteniendo su estructura nativa. Este es el caso de los concentrados (MCC) o aislados de caseína micelar (MCI), los cuales han sido parcialmente separados de las proteínas del suero, lactosa y minerales solubles y finalmente secados por pulverización. Sin embargo, estos concentrados proteicos en polvo deben dispersarse y disolverse para desempeñar su función como ingredientes alimentarios, lo cual presenta un problema debido a su difícil reconstitución. Como alternativa, su manejo en forma líquida supondría una importante ventaja competitiva, pero se debe tener en cuenta que su manipulación en forma líquida los hace altamente vulnerables al deterioro microbiológico y a otros tipos de alteraciones. Por todo ello, en esta Tesis Doctoral se ha explorado el comportamiento y estabilidad de estos concentrados líquidos tratados por altas presiones; así como, su combinación con una barrera adicional antibacteriana como es la nisina. También se ha recurrido a esta tecnología no térmica para tratar mezclas de bases lácteas para la elaboración de yogures con alto contenido en proteína. Además, en las instalaciones de FrieslandCampina Innovation Centre (Wageningen, Países Bajos), se ha profundizado en el estudio del efecto de las sales secuestrantes, concretamente el hexametafosfato de sodio (SHMP) y citrato trisódico (TSC), sobre soluciones de MCI, así como en el efecto que tiene el SHMP sobre estas soluciones cuando son tratadas térmicamente y su estabilidad en el tiempo. En cuanto a los hallazgos más relevantes, indicar que el tratamiento de los concentrados de caseína micelar líquidos (LMCC) a 600 MPa durante 5 minutos ha conseguido garantizar la calidad microbiana, sin embargo, a esas altas presiones se producen procesos de fraccionamiento y reagrupación en las estructuras micelares que repercuten en la textura final. No obstante, se ha visto que la adición de nisina a los LMCC permite reducir la presión aplicada a 450 MPa alcanzado los niveles de reducción microbiana obtenidos a 600 MPa, pero sin afectar las propiedades fisicoquímicas de los concentrados. Respecto a los yogures elaborados con LMCC tratados tanto térmicamente como por altas presiones, se ha comprobado que ambos han presentado gran capacidad de retención de agua y firmeza, pero se han observado diferencias entre los dos tratamientos en cuanto a la viscosidad del yogur (batido), resaltando la potencialidad del tratamiento no térmico. Como aspectos relevantes de las investigaciones con MCI, se ha comprobado que ambas sales secuestrantes (TSC y SHMP) inducen la disrupción de la micela de caseína, pero su modo de acción es distinto. Así pues, se ha hipotetizado que TSC forma complejos solubles de Ca-Citrato solubilizando el fosfato inorgánico de la micela, mientras que SHMP actúa como agente peptizante induciendo a la disrupción del fosfato cálcico micelar, pero no solubilizándolo. Además, cuando el SHMP es añadido a una solución de MCI y calentado a distintas combinaciones de temperatura y tiempo, simulando las condiciones industriales, se produce una hidrólisis del SHMP que provoca un descenso acusado del pH y de la viscosidad. No obstante, estas soluciones con SHMP han mostrado muy buena estabilidad durante su almacenamiento, demostrando su capacidad como agente estabilizante., The use of milk protein concentrates as ingredients is increasing due to their excellent functional and nutritional value. A good strategy for obtaining these concentrates is the use of membrane filtration as it allows to separate and concentrate specific compounds of milk maintaining their native structure. This is the case of micellar casein concentrates (MCC) or isolates (MCI), which have been partially separated from whey proteins, lactose and soluble minerals and finally spray-dried. However, these powder protein concentrates have to be dispersed and dissolved before their use to perform their function as food ingredients, which presents a problem due to their difficult reconstitution. Alternatively, their use in liquid form would provide an important completive advantage, nevertheless, their handling in liquid form makes them highly vulnerable to microbiological spoilage and other alterations. This dissertation, therefore, set out to explore the behaviour and stability of these liquid concentrates treated by high-pressure processing as well as their combination with an antibacterial such as nisin. This non-thermal technology has also been used to treat dairy bases for high-protein content yogurt manufacture. In addition, during the predoctoral stay carried out in FrieslandCampina Innovation Centre (Wageningen, The Netherlands), it has been studied in depth the effect of sequestering salts: sodium hexametaphosphate (SHMP) and trisodium citrate (TSC) on MCI solutions, as well as the heat-induced changes of SHMP on MCI and their stability over time. Concerning the most relevant findings, the treatment of liquid micellar casein concentrates (LMCC) at 600 MPa for 5 minutes managed to guarantee microbial quality; however, at these high pressures, fractionation and regrouping processes occurred in the micellar structures that affected the final texture. It was also found that the addition of nisin to LMCC allowed reducing the pressure applied to 450 MPa reaching a similar microbial reduction level that the one obtained at 600 MPa but without affecting the physicochemical properties of the concentrates. Concerning the yogurts made with LMCC treated both thermally and by high pressure, it was found that both showed high water retention capacity and firmness, and the differences were observed between the two treatments in terms of yogurt viscosity (stirred), highlighting the potential of the non-thermal treatment. As the most relevant findings of the research carried out with MCI, it has been demonstrated that both sequestering salts induced the micelle disruption but their mechanism differed. Thus, it has been hypothesized that TSC forms soluble Ca-Citrate complexes by solubilizing the inorganic phosphate in the micelle, while SHMP acts as a peptizing agent inducing the disruption of micellar calcium phosphate, but not solubilizing it. Furthermore, when SHMP was added to an MCI solution and heated at different combinations of temperature and time, simulating industrial conditions, hydrolysis of SHMP occurred resulting in a marked decrease in pH and viscosity. However, these solutions with SHMP showed very good stability during storage, demonstrating its ability as a stabilizing agent., Para la realización de esta tesis doctoral, Arantza García obtuvo una ayuda predoctoral otorgada por el Instituto de Investigación IS-FOOD, adscrito a la Universidad Pública de Navarra (Resolución 1385/2017), así como dos ayudas para la realización de la estancia predoctoral otorgadas por el Gobierno de Navarra (Nº expediente: 0011-3564-2021-000015) y por Erasmus+ (CampusIberus), y que tuvo lugar en FrieslandCampina Innovation Centre, Wageningen (Países Bajos). La primera parte de este trabajo (Block 1) se incluye en el proyecto de investigación OPTICASEINAPPLY (Nº expediente: 0011-1365-2017-000173), financiado por el Gobierno de Navarra (Servicio de Innovación del Departamento de Desarrollo Económico del Gobierno de Navarra)., Programa de Doctorado en Agroalimentación (RD 99/2011), Nekazaritzako Elikagaietako Doktoretza Programa (ED 99/2011)
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Tesis doctoral (DoctoralThesis)

Sensitivity of photonic sensors through the textural properties of siliceous membrane materials with organic and/or inorganic guests, Sensibilidad de sensores fotónicos a través de las propiedades texturales de materiales de membrana silíceos con huéspedes orgánicos y/o inorgánico

  • Rosales Reina, María Beatriz
El objetivo de esta Tesis Doctoral es el desarrollo de sensores de fibra óptica (SFO) para la detección de vapores y iones metálicos en disolución acuosa, así como para la monitorización del pH. Con esta perspectiva, el analito es el adsorbato y la membrana el adsorbente. Esta analogía permite poner en un primer plano la importancia de la química de superficies en el mecanismo de medida de un sensor químico de fibra óptica, lo que implica el diseño de materiales para membranas. Dicho diseño debe buscar conseguir interacciones analito-membrana específicas, selectivas y lábiles que permitan medidas rápidas., The objective of this Doctoral Thesis is to develop optical fibre sensors (OFSs) for the detection of vapours and metal ions in solution, as well as for monitoring pH variations. Within this framework, the analyte is considered the adsorbate, and the fibre sensitive membrane acts as the adsorbent. This analogy underlines the importance of surface chemistry in the sensing mechanism of an optical fibre chemical sensor and the requirement of the tailored preparation of membranes. This approach seeks to achieve specific, selective, and reversible analyte-membrane interactions that facilitate rapid measurement., This Doctoral Thesis has been developed thanks to the funding received from Ministerio de Ciencia e Innovación of the Government of Spain (projects PID2020-113558RB-CB42 and PID2022-137437OB-I00). The financial support provided by the Government of Navarre for a predoctoral grant within the Project ‘Sensores de Fibra Óptica Preparados con Membranas Silíceas Dopadas con Complejos de Lantánidos (SENSOR-SiLn)’ (grant number 0011-1307-2020-000019) is gratefully acknowledged. B. Rosales Reina would also like to thank Universidad Pública de Navarra for the predoctoral international mobility grant that allowed to complete a three-month-long doctoral stay (2024) in the School of Science & Technology at the City and St. George’s University of London., Programa de Doctorado en Ciencias y Tecnologías Industriales (RD 99/2011), Industria Zientzietako eta Teknologietako Doktoretza Programa (ED 99/2011)
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Tesis doctoral (DoctoralThesis)

Estudio de infección policlonal, vida extracelular y adaptación metabólica de Haemophilus influenzae en el sistema respiratorio humano

  • Asensio López, Javier
El tutor de la tesis es Jon Mirena Veramendi Charola, Este trabajo de Tesis Doctoral aborda tres aspectos de la interacción entre la bacteria Haemophilus influenzae no tipificable (HiNT) y el sistema respiratorio humano, considerando el desarrollo de herramientas genéticas de marcaje diferencial y su aplicación al estudio de infecciones policlonales (Capítulo 1), el potencial terapéutico anti-biofilm de moléculas derivadas de cinamaldehído (Capítulo 2), y el papel del triptófano y sus derivados en la modulación de la interacción hospedador-patógeno (Capítulo 3). Los procedimientos clínicos estandarizados para el tratamiento de infecciones bacterianas se basan en la identificación del patógeno causante y la determinación de su susceptibilidad antibiótica, a menudo utilizando bacterias aisladas a partir de una única colonia. En el caso de patógenos respiratorios, esta práctica puede ser cuestionable ya que los pacientes crónicos pueden estar simultáneamente colonizados por clones distintos de un mismo patógeno, con características genotípicas y fenotípicas diferentes que pueden conducir a diferentes perfiles de susceptibilidad antibiótica. Esta heterogeneidad es detectada en aislados de H. influenzae obtenidos a partir de muestras respiratorias de pacientes respiratorios crónicos, cuyos diferentes perfiles de susceptibilidad antibiótica pueden provocar fallo terapéutico en la práctica clínica. En el Capítulo 1 de este Trabajo, generamos una colección de plásmidos modulares que permiten el marcaje diferencial de cepas de H. influenzae. Empleando este marcaje diferencial, estudiamos la formación de biofilm mixtos formados por dos cepas de H. influenzae genéticamente distintas, con diferente capacidad de formación de biofilm y susceptibilidad antibiótica, mostrando la acción selectiva de los antibióticos en estos biofilms policlonales. Además, estudiamos la dinámica de co-infección epitelial por dos cepas de H. influenzae, mostrando la localización intracelular de cepas con distinta capacidad invasiva. Este panel de herramientas abre el camino al estudio de comunidades bacterianas policlonales y polimicrobianas en las que participa H. influenzae. Por otra parte, patologías respiratorias crónicas como la Enfermedad Pulmonar Obstructiva Crónica (EPOC) facilitan el acceso pulmonar de H. influenzae, que persiste formando biofilms, un estilo de vida protector frente al sistema inmune y tratamientos antibióticos, que cronifica la infección y facilita la aparición de resistencias. H. influenzae está incluido en la Lista de Patógenos Prioritarios de la Organización Mundial de la Salud por su resistencia a ampicilina, resultando prioritario el desarrollo de nuevos antimicrobianos y la estandarización de métodos de evaluación de eficacia de fármacos anti-biofilm. En el Capítulo 2 de este Trabajo, presentamos un panel de protocolos para el análisis sistemático de fármacos anti-biofilm. Como prueba de concepto, evaluamos el efecto antimicrobiano de moléculas derivadas del cinamaldehído frente a cepas de H. influenzae con distinta capacidad de formación de biofilm. Observamos que (E)-Trans-2- nonenal y (E)-3-Decen-2-ona inhiben la formación de biofilms y erradican biofilms preformados por H. influenzae. Además, la baja toxicidad de (E)-Trans-2-nonenal llevó a su selección para encapsulación en nanopartículas poliméricas, que permiten una mayor solubilidad manteniendo el efecto anti-biofilm, y pueden ser útiles para una liberación controlada y segura de fármacos. Por último, H. influenzae dispone de mecanismos pato-adaptativos entre los que se encuentra la evasión de la inmunidad nutricional. El triptófano (Trp) es un metabolito esencial para esta bacteria, que sintetiza su propio Trp y capta Trp exógeno a través de al menos dos sistemas de transporte. Por su parte, el hospedador restringe la disponibilidad de Trp a través de la acción de la enzima indolamina 2,3 dioxigenasa IDO, que cataboliza Trp generando kineurinas que, junto a otros derivados de Trp, son ligandos del receptor de hidrocarburos de arilos AhR. IDO y AhR participan en el control de la respuesta inmune y el mantenimiento de la homeostasis pulmonar. En el Capítulo 3 de este Trabajo, analizamos el efecto de la disponibilidad de Trp exógeno y endógeno en la fisiología e infección respiratoria por H. influenzae. Así mismo, analizamos cómo la disponibilidad de Trp en el sistema respiratorio influye en la interacción hospedador-patógeno, mostrando que el Trp y sus derivados modifican la expresión de IDO, AhR y sus efectores, modulando la respuesta del hospedador frente a la infección por H. influenzae. En conjunto, el Trabajo realizado durante esta Tesis Doctoral supone un avance significativo en el conocimiento de las bases moleculares de la interacción entre H. influenzae y el sistema respiratorio humano, lo que puede ser de utilidad en el desarrollo de estrategias que mejoren el manejo clínico de enfermedades asociadas a este patógeno., This PhD Thesis work addresses three aspects of the interaction between the nontypeable Haemophilus influenzae (NTHi) and the human respiratory system, considering the development of genetic tools for differential labelling and their application to the study of polyclonal infections (Chapter 1), the anti-biofilm therapeutic potential of cinnamaldehydederived molecules (Chapter 2), and the role of tryptophan and its derivatives in modulating this host-pathogen interaction (Chapter 3). Standardized clinical procedures for the treatment of bacterial infections are based on pathogen identification and determination of its antibiotic susceptibility, often performed on bacteria isolated from a single colony. In the case of respiratory pathogens, this practice may be questionable since chronic patients can be simultaneously colonized by different strains of the same pathogen, with distinct genotypic and phenotypic characteristics that can lead to different antibiotic susceptibility profiles. This heterogeneity has been detected in H. influenzae isolates obtained from respiratory samples of chronic respiratory patients, whose differential antibiotic susceptibility profiles can lead to therapeutic failure in clinical practice. In Chapter 1 of this work, we generated a collection of module-based plasmids that allow differential labelling of H. influenzae strains. Using this differential labelling, we studied the formation of mixed biofilms by two genetically distinct H. influenzae strains, with different biofilm-forming capacities and antibiotic susceptibility, proving selective antibiotic action in these polyclonal biofilms. Additionally, we studied the dynamics of epithelial co-infection by two H. influenzae strains, revealing the intracellular localization of strains with heterogeneous invasive capacities. This panel of genetic tools paves the way for polyclonal and polymicrobial studies of the different H. influenzae lifestyles. On the other hand, chronic respiratory diseases such as Chronic Obstructive Pulmonary Disease (COPD) promote the pulmonary access of opportunistic pathogens like H. influenzae, which persist by forming biofilms, a protective lifestyle that contributes to chronicity of infection and facilitates the emergence of antibiotic resistances. H. influenzae is included in the World Health Organization List of Priority Pathogens due to its resistance to ampicillin, making it a priority to both develop new antimicrobials and standardize methods for evaluating the efficacy of anti-biofilm drugs. In Chapter 2 of this work, we present a panel of protocols for systematic analysis of anti-biofilm drug effect, customized to H. influenzae biofilms. As proof of concept, we evaluated the antimicrobial effect of cinnamaldehyde-derived molecules against H. influenzae strains with different biofilmforming capacities. We observed that (E)-Trans-2-nonenal and (E)-3-Decen-2-one inhibit the formation and eradicate pre-formed biofilms by H. influenzae. Additionally, the low toxicity of (E)-Trans-2-nonenal led to its selection for encapsulation in polymeric nanoparticles, which allow for greater solubility, maintain the anti-biofilm effect, and may be useful for the controlled and safe release of drugs. Lastly, H. influenzae has patho-adaptation mechanisms including the evasion of nutritional immunity. Tryptophan (Trp) is an essential metabolite for this bacterium, which is able to synthesize its own Trp and to acquire exogenous Trp through at least two transport systems. On the other hand, the host restricts Trp availability through the action of the enzyme indoleamine 2,3-dioxygenase (IDO), which catabolizes Trp generating kynurenines that, along with other Trp derivatives, act as ligands for the aryl hydrocarbon receptor (AhR). IDO and AhR are involved in controlling the immune response and maintaining pulmonary homeostasis. In Chapter 3 of this work, we analyzed the effect of exogenous Trp availability on the physiology of H. influenzae, as well as the importance of Trp synthesis in respiratory infection by this pathogen. Furthermore, we examine how the availability of Trp in the respiratory system influences this host-pathogen interaction, showing that Trp and its derivatives modulate the expression of IDO, AhR, and their effectors, thereby modulating the host's immune response to H. influenzae infection. Altogether, the work carried out during this PhD Thesis represents a significant step forward in the understanding of the molecular basis of the interaction between H. influenzae and the human airways, which may be useful in the development of strategies to improve its clinical management., Este Trabajo de Tesis Doctoral se ha desarrollado mediante el disfrute de un Contrato del Programa “Doctorados Industriales” de Gobierno de Navarra (0011-1408- 2020-000007), y un contrato adscrito al proyecto VALSANA (0011-1411-2023-000039) del Servicio de Proyectos Estratégicos de la S4 y Emprendimiento, Departamento de Industria y Transición Ecológica y Digital Empresarial de Gobierno de Navarra., Programa de Doctorado en Biotecnología (RD 99/2011), Bioteknologiako Doktoretza Programa (ED 99/2011)
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Tesis doctoral (DoctoralThesis)

Assessing the contribution of optical, SAR and LiDAR data for vegetation applications: from crop monitoring to forest characterization

  • Aranguren Erice, Itxaso
El seguimiento de la vegetación en ecosistemas agrícolas y forestales es esencial para la seguridad alimentaria, la gestión forestal sostenible y la mitigación del cambio climático. La teledetección proporciona observaciones sistemáticas y espacialmente consistentes a gran escala, convirtiéndose en una herramienta fundamental en este ámbito. La disponibilidad de diferentes tipos de sensores ofrece perspectivas complementarias sobre las características y dinámicas de la vegetación, aunque su utilidad, empleado de forma individual o combinada, sigue siendo un área de investigación activa. Esta tesis evalúa el potencial de la teledetección óptica, SAR y LiDAR para el seguimiento de la vegetación en ecosistemas agrícolas y forestales, abordando cuatro objetivos específicos. En primer lugar, se evaluaron las características de intensidad y polarimetría de Sentinel-1 para el modelado de series temporales de NDVI de Sentinel-2 en cuatro tipos de cultivos. Se obtuvieron buenos resultados para la cebada, el trigo y el girasol, identificándose las variables SAR temporales como un factor clave para una reconstrucción precisa del NDVI. En segundo lugar, se evaluó el uso de Sentinel-1, Sentinel-2 y LiDAR para la clasificación de tipos y especies forestales en tres niveles taxonómicos. Sentinel-2 resultó ser el sensor más informativo, con LiDAR aportando información estructural complementaria. Se alcanzaron precisiones globales de 0,90, 0,80 y 0,79 en los tres niveles. En tercer lugar, los mismos sensores fueron evaluados para la estimación del área basimétrica y el volumen de masa en hayedos europeos. El LiDAR proporcionó la mayor capacidad predictiva, con Sentinel-2 aportando información espectral complementaria. Sentinel-1 añadió una capacidad predictiva marginal bajo condiciones de dosel denso. Por último, se investigó la coherencia interferométrica en banda L derivada de los productos GSLC de NISAR para la estimación de la biomasa aérea más allá del límite de saturación del coeficiente de retrodispersión. Se adoptó un marco de corrección de residuos en dos etapas, que mostró mejoras significativas en el enfoque basado en datos para un área de alta biomasa. En conjunto, se espera que los resultados de esta tesis contribuyan a un mejor entendimiento del potencial de los diferentes sensores de teledetección para el seguimiento de la vegetación. Los hallazgos sugieren que el avance puede provenir no solo de la integración de sensores, sino también de la explotación de toda la información disponible en los productos SAR existentes, combinada con estrategias de modelado más avanzadas., Vegetation monitoring across agricultural and forest ecosystems is essential for food security, sustainable forest management, and climate change mitigation. Remote sensing provides systematic, spatially consistent observations at large scales, becoming an indispensable tool for this purpose. The availability of different sensor types offers complementary perspectives on vegetation characteristics and dynamics, though their utility, either used individually or in combination, remains an active research area. This thesis evaluates the potential of optical, SAR, and LiDAR remote sensing for vegetation monitoring across agricultural and forest ecosystems, addressing four specific objectives. First, Sentinel-1 intensity and polarimetric features were evaluated for modelling Sentinel-2 NDVI time series across four crop types. Strong performance was achieved for barley, wheat, and sunflower, with temporal SAR features identified as a critical factor for accurate NDVI reconstruction. Second, the use of Sentinel-1, Sentinel-2, and LiDAR was assessed for forest type and species classification across three taxonomic levels. Sentinel-2 emerged as the most informative sensor, with LiDAR contributing complementary structural information. Overall accuracies of 0.90, 0.80, and 0.79 were achieved across the three levels. Third, the same sensors were evaluated for basal area and stand volume estimation in European beech stands. LiDAR provided the strongest predictive capacity, with Sentinel-2 contributing complementary spectral information. Sentinel-1 added negligible predictive power under dense canopy conditions. Finally, L-band interferometric coherence derived from NISAR GSLC products was investigated for aboveground biomass retrieval beyond the backscatter saturation limit. A two-stage residual correction framework was adopted, showing meaningful improvements within the data-driven framework at a high-biomass site. Overall, the results of this thesis are expected to contribute to a better understanding of the potential of different remote sensors for vegetation monitoring. The findings suggest that progress may come not only from sensor integration, but also from exploiting the full information content of existing SAR products combined with more advanced modelling strategies., This thesis was supported by the grant “Predoctoral grants 2023 from the Government of Navarra for the implementation of doctoral programs of interest to Navarra”, and through the projects forestOBS (project code 0011-1365-2021-000072), granted in the 2021 call for R&D projects by the Government of Navarre, and ReSAg (PID2019-107386RB-I00) and DAMAGE (PID2023-0152885OB-I00), funded by the Spanish State Research Agency (Agencia Estatal de Inves-tigación, AEI), Ministry of Science, Innovation and Universities. Projects included funds from the European Regional Development Fund (FEDER-UE)., Programa de Doctorado en Ciencias y Tecnologías Industriales, Industria Zientzietako eta Teknologietako Doktoretza Programa
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Tesis doctoral (DoctoralThesis)

Optimization of acoustic fields: advances towards its use for matter manipulation and contactless fabrication, Optimización de campos acústicos: avances hacia su uso para la manipulación de materia y la fabricación sin contacto

  • Ezcurdia Aguirre, Íñigo Fermín
Los campos de presión acústica son capaces de modelar y levitar partículas de una amplia gama de materiales y tamaños a través del aire, el agua o el tejido biológico. Esto tiene aplicaciones en cristalografía, manipulación celular, escenarios lab-on-a-chip, farmacología, transporte sin contacto e incluso levitación de seres vivos. En general, la investigación de campos de presión acústica ha experimentado avances significativos en los últimos años. Su flexibilidad y sus posibles aplicaciones han aumentado considerablemente con el desarrollo de técnicas holográficas y el uso de optimizadores. Sin embargo, aún hay margen de mejora, ya que las limitaciones dificultan la aplicación de los campos acústicos en diversos escenarios de investigación. Por ejemplo, no existe una plataforma de hardware unificada que motive de forma flexible la investigación exploratoria en aplicaciones de holografía acústica. La mayoría de los dispositivos comerciales o de caseros carecen de la resolución o la potencia que necesitan las personas investigadoras, por lo que tienen que fabricar dispositivos más complejos y caros. Además, investigaciones anteriores se han centrado en la levitación y manipulación de pequeñas partículas y gotas; sin embargo, aún no se ha desarrollado un prototipo completo para la fabricación sin contacto; no existen artículos científicos que estudien el atrapamiento de objetos alargados tanto en posición como en orientación. Además, la microfluídica está limitada en cuanto a la manipulación tridimensional (3D), el tamaño de las gotas y la contaminación cruzada. Esta tesis ofrece una introducción exhaustiva a la optimización de los campos acústicos, repasando su importancia en aplicaciones de múltiples ámbitos de la investigación y la industria. Esta tesis también examina las limitaciones y deficiencias previamente expuestas y presentes en el actual diseño y aplicación de campos acústicos. Se proponen algoritmos novedosos para generar los campos deseados y mejorar significativamente su resolución y potencia mediante multiplexación espacial y temporal. Se presenta una plataforma de hardware abierta y asequible para facilitar la adaptación a los requisitos experimentales de los investigadores que exploran nuevas aplicaciones de los hologramas ultrasónicos. Se diseñan y evalúan trampas acústicas óptimas para manipular elementos alargados controlando su posición y orientación. Se demuestra la fabricación sin contacto utilizando trampas acústicas de piezas alargadas mediante fabricación aditiva basada en partículas levitadas, varillas y resina UV; también se ilustra la adición sobre otros objetos y la construcción dentro de contenedores. Por último, se propone un sistema, destinado a microfluídica 3D, basado en ultrasonidos focalizados a través de una malla hidrófoba. Es sistema es capaz de manejar un gran número de gotas (> 40µL), y capaz de fusionarlas/dividirlas o propulsarlas verticalmente, este sistema mejora significativamente los sistemas EWOD ya existentes generando una menor contaminación superficial. Esta tesis presenta estos logros y sus trabajos relacionados, modelos, metodologías, procedimientos y conclusiones. Espero que estos trabajos supongan un avance significativo en la investigación de los campos acústicos y puedan inspirar y facilitar futuras aplicaciones novedosas de los hologramas acústicos por parte de las personas investigadoras en diversos ámbitos del mundo académico y de la industria., Acoustic pressure fields are capable of patterning and levitating particles of a wide range of materials and sizes through air, water or biological tissue. This has applications in crystallography, cell manipulation, lab-on-a-chip scenarios, pharmacology, containerless transportation and even levitation of living things. Overall, the research domain of acoustic pressure fields has seen significant advances in recent years. Its flexibility and potential applications have been greatly increased with the development of holographic techniques and the use of optimizers. However, there is still room for improvement, as limitations hinder the application of acoustic fields in various research scenarios. For example, there is no unified hardware platform that can flexibly support exploratory research in acoustic holography applications. Most commercial or DIY devices lack the resolution or power that researchers require, so they need to fabricate more complex, cumbersome and expensive devices. Moreover, previous research has focused on the levitation and manipulation of small particles and droplets; however, a full prototype for contactless fabrication has yet to be developed since there is no existing work on trapping elongated objects in position and orientation. Furthermore, microfluidics is limited in terms of three-dimensional (3D) manipulation, droplet size and cross-contamination. This thesis provides a comprehensive introduction to the optimization of acoustic fields, reviewing its importance in applications across multiple research and industry domains. This thesis also examines the previously stated limitations and shortcomings of the design and application of acoustic fields. Novel algorithms are proposed to generate desired target fields and to significantly improve their resolution and power through spatial and temporal multiplexation. An open and affordable hardware platform is presented to facilitate customisation for experimental requirements by researchers exploring novel applications for ultrasonic holograms. Optimum acoustic traps are designed and evaluated to lock elongated elements in position and orientation. Contactless fabrication using full acoustic trapping of elongated parts is demonstrated through additive manufacturing based on levitated particles, sticks and UV resin; the addition on top of other objects and building inside containers is also illustrated. Finally, a 3D digital microfluidics system is proposed based on focused ultrasound through a hydrophobic mesh. Able to handle a large number of liquid droplets (> 40µL), and capable of merging/splitting them or vertically propelling them, this system significantly improves already existing EWOD systems generating less surface contamination. This thesis presents these achievements and their related works, models, methodologies, procedures and conclusions. I hope that these pieces of work are a significant advancement in the research of acoustic fields and may inspire and facilitate future novel applications of acoustic holograms by researchers in various domains of academia and industry., Government of Navarre (FEDER) - 0011-1365-2019-000086, Jóvenes Investigadores UPNA - PJUPNA1923, EU Horizon 2020 research and innovation programme - Nº 101017746 TOUCHLESS, Programa de Doctorado en Ciencias y Tecnologías Industriales (RD 99/2011), Industria Zientzietako eta Teknologietako Doktoretza Programa (ED 99/2011)
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Tesis doctoral (DoctoralThesis)

Local plant-based and hybrid protein foods with the revalorisation of broccoli by-products as a circular economy strategy

  • González Peñalver, José Miguel
Esta tesis doctoral investiga el desempeño ambiental de las estrategias de valorización de subproductos, basadas en los principios de la economía circular y el uso de fuentes locales de proteína vegetal. Para ello, se aplicaron metodologías de evaluación del impacto ambiental, utilizando el análisis de huella de carbono y huella hídrica, en tres áreas clave: (1) la valorización de subproductos del brócoli, (2) la producción de aperitivos veganos a base de guisante y (3) el desarrollo de nuevos prototipos cárnicos, híbridos y vegetales, elaborados con ingredientes locales de Navarra. La primera fase se centró en la recuperación de glucosinolatos, compuestos bioactivos extraídos de subproductos del brócoli. Se realizó un análisis de la huella de carbono y huella hídrica comparando dos escenarios: la producción convencional de brócoli y un escenario adicional con la extracción de glucosinolatos. Aunque este paso extra mejoró la eficiencia en el uso de los recursos, también provocó un aumento en los impactos ambientales debido al excesivo uso de disolventes y bienes, así como a la baja concentración de glucosinolatos en los subproductos, alcanzando un incremento del 37,6% en las emisiones de gases de efecto invernadero y un 4,6% en el uso de agua. Para mejorar la sostenibilidad del proceso, se propusieron estrategias de optimización, como la recuperación de disolventes. Además, se evaluó el desempeño ambiental de un aperitivo a base de guisante producido en Navarra, que presentó una huella de carbono inferior a la registrada para otros productos similares en la literatura y un uso del agua dentro del rango de productos similares. En comparación con alternativas a base de soja, los productos de guisante mostraron un menor uso de agua azul y gris, y presentaron mayor consumo de agua verde, lo que refleja una mayor dependencia de las precipitaciones. Se identificaron estrategias de mejora en el proceso productivo, como la reducción de pérdidas en la cadena de valor y la contratación de fuentes de electricidad renovables, lo que permitiría disminuir la huella de carbono en un 17% (de 0,12 a 0,10 kg CO₂e por cada 100 g de producto) y reducir el consumo de agua verde en un 3%. Para aprovechar los beneficios esperados de los productos a base de guisante y la recuperación de glucosinolatos, se incorporaron estos compuestos en tres prototipos de búrgueres: cárnica, híbrida y vegetal (siendo la matriz proteica vegetal harina de guisante). Estos prototipos fueron mejorados nutricional y tecnológicamente mediante la sustitución de grasa animal por grasa vegetal y su procesamiento mediante alta presión hidrostática y cocción al vacío (sous-vide). Se evaluaron en términos de seguridad microbiológica, composición nutricional, textura, atributos sensoriales y huella de carbono. Los resultados mostraron que las búrgueres vegetales tenían la menor huella de carbono (0,12 kg CO₂e), seguidas de las híbridas (0,87 kg CO₂e) y las cárnicas (1,62 kg CO₂e). Las búrgueres híbridas presentaron una mejor textura en comparación con sus equivalentes cárnicos y vegetales, además de ofrecer un perfil nutricional más equilibrado al combinar beneficios de ingredientes de origen vegetal y animal, posicionándolas como una alternativa viable y sostenible. Esta investigación pone de manifiesto el potencial de los enfoques de economía circular y el uso de ingredientes locales. Sin embargo, subraya la importancia de evaluar el impacto de cada estrategia, ya que algunas prácticas de valorización pueden parecer ambientalmente beneficiosas a nivel teórico, pero no cumplir con las expectativas (por ejemplo, la revalorización de los glucosinolatos cuando implica un elevado uso de disolventes y recursos)., This doctoral thesis investigates the environmental performance of by-product valorisation strategies based on circular economy principles and the use of local plant-based protein sources. Environmental impact assessment methodologies, using carbon and water footprint analyses, were applied to evaluate three key areas: (1) the valorisation of broccoli by-products, (2) the production of pea-based vegan snacks, and (3) the development of novel meat, hybrid, and vegan prototypes using local ingredients from Navarra. A central focus was the recovery of glucosinolates, bioactive compounds extracted from broccoli by-products, to enhance the nutritional value of food prototypes in an environmentally sustainable manner. A carbon and water footprint assessment compared two scenarios in Navarra: conventional broccoli production versus an additional glucosinolate extraction step. Although this extra step improved resource efficiency, it also led to an increase in environmental impacts due to the excessive use of solvent and goods and the low concentration of glucosinolates in the by-products, reaching a 37.6% rise in greenhouse gas emissions and a 4.6% increase in water use. Optimisation strategies, such as solvent recuperation, were proposed to improve process sustainability. Additionally, the study assessed the environmental performance of a Navarra-produced pea-based snack, which exhibited lower carbon footprints than those reported in the literature and water usage within the range of similar products. Compared to soy-based alternatives, pea-based snacks had lower blue and grey water usage and higher green water use, reflecting greater reliance on rainfall. Measures such as reducing supply chain losses and incorporating renewable electricity in production could lower the carbon footprint by 17% (from 0.12 to 0.10 kg CO₂e per 100 g) and reduce green water consumption by 3%. To leverage the benefits of pea-based products and glucosinolate recovery, extracted glucosinolates were incorporated into three patty prototypes: meat-based, hybrid, and plant-based (being the vegetable protein matrix pea flour). These prototypes were nutritionally and technologically enhanced by replacing animal fat with vegetable fat and using high-pressure processing and sous-vide cooking. They were evaluated for microbiological safety, nutritional composition, texture, sensory attributes, and carbon footprint. Results showed that plant-based patties had the lowest carbon footprint (0.12 kg CO₂e), followed by hybrid patties (0.87 kg CO₂e), and meat-based patties (1.62 kg CO₂e). Hybrid patties exhibited improved texture compared to their meat and plant-based counterparts and offered a more balanced nutritional profile, positioning them as a viable and sustainable alternative. This research highlights the potential of circular economy approaches and local ingredient utilisation. However, it underscores the importance of impact assessment, as some valorisation strategies may appear sustainable but fail under thorough analysis (e.g. glucosinolates revalorisation when it involves a high use of solvents and resources)., The research activities of this doctoral thesis have been carried out within the framework of the project ‘Design of healthy and sustainable food and ingredients from the circular economy’ (reference number: 0011-1411-2021), funded by the Government of Navarra through the programme for the Implementation of Strategic R&D Projects for the period 2021-2024. A mobility grant was awarded by the Public University of Navarra in 2023, as per Resolution Number 131/2023., Programa de Doctorado en Agroalimentación (RD 99/2011), Nekazaritzako Elikagaietako Doktoretza Programa (ED 99/2011)
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Tesis doctoral (DoctoralThesis)

Valorización de la hoja de olivo (Olea europaea L.) a través del desarrollo de extractos antioxidantes para la industria alimentaria

  • Filgueira Garro, Itxaso
La hoja de olivo (Olea europea L.) es un residuo de la industria oleícola que puede llegar a suponer hasta un 5 % de la masa de aceituna que se recibe en las almazaras. Sin embargo, su concentración en compuestos fenólicos, con una elevada capacidad antioxidante, podría suponer la valorización de este residuo en la industria alimentaria. El objetivo principal de esta tesis doctoral fue la valorización de la hoja de olivo mediante la aplicación del extracto encapsulado de sus compuestos fenólicos como antioxidante en aceite de fritura. Para la obtención del extracto de hoja de olivo (EHO), se abordó la caracterización y estabilización de las hojas mediante diferentes métodos de secado (estufa, estufa a vacío, liofilización y secado al aire) y se optimizó la extracción de los compuestos fenólicos mediante extracción sólido-líquido convencional (ESL), extracción sólido-líquido asistida por ultrasonidos (EAU) y extracción con CO2 supercrítico (EFS). Además, se investigaron dos tecnologías para la encapsulación de EHO, dispersión y atomización (CDA) y emulsión doble y atomización (CEDA). Se determinó el efecto antioxidante de las CDA y CEDA sobre aceite de girasol refinado. Finalmente, se investigó el efecto de la incorporación de EHO encapsulado en aceite de fritura sobre las características y la aceptación sensorial de patatas fritas. Entre las hojas de olivo caracterizadas, se seleccionaron las hojas de ‘Arbequina’ ecológicas secadas al aire. La EAU fue el método más efectivo en la extracción de compuestos fenólicos de la hoja de olivo con capacidad antioxidante. Las CDA y CEDA desarrolladas aumentaron la estabilidad oxidativa y térmica del aceite de girasol. Las CDA, además, mejoraron la estabilidad durante la fritura del aceite de girasol en un 26,2 % respecto al aceite sin antioxidantes y en un 10,5 % respecto al aceite con tertbutilhidroquinona (TBHQ). Por último, la incorporación de EHO en forma de CDA al aceite de girasol no afectó a la aceptación sensorial de las patatas fritas. Por tanto, según los resultados expuestos en esta tesis doctoral, la cápsula de EHO (CDA) desarrollada en esta investigación podría ser una alternativa natural a los antioxidantes sintéticos utilizados actualmente en la industria alimentaria., Olive (Olea europaea L.) leaf is a residue of olive industry that could suppose up to the 5 % of the olive’s mass that is received in the olive mills. However, its concentration in phenolic compounds, with high antioxidant capacity, could entail the valorization of this residue in the food industry. The main objective of this doctoral thesis was the valorization of the olive leaf through the application of the encapsulated extract of its phenolic compounds as an antioxidant in frying oil. To obtain the olive leaf extract (EHO), the characterization and stabilization of the leaves were addressed by different drying methods (oven, vacuum oven, freeze-drying and airdrying) and the extraction of phenolic compounds was optimized by conventional solidliquid extraction (ESL), ultrasound-assisted solid-liquid extraction (UAE) and supercritical CO2 extraction (EFS). In addition, two technologies for EHO encapsulation, dispersion and spray-drying (CDA) and double emulsion and spray-drying (CEDA), were investigated. The antioxidant effect of CDA and CEDA on refined sunflower oil was determined. Finally, the effect of incorporating encapsulated EHO in frying oil was investigated on the characteristics and sensory acceptance of French fries. Among the olive leaves characterized, air-dried organic 'Arbequina' leaves were selected. The EAU was the most effective method in the extraction of phenolic compounds from the olive leaf with antioxidant capacity. The CDA and CEDA developed increased the oxidative and thermal stability of sunflower oil. The CDA also improved the stability during frying of sunflower oil by 26.2 % compared to the oil without antioxidants and by 10.5 % compared to the oil with tertbutylhydroquinone (TBHQ). Finally, the incorporation of EHO as CDA to sunflower oil did not affect the sensory acceptance of the French fries. Therefore, according to the results presented in this doctoral thesis, the EHO capsule (CDA) developed in this research could be a natural alternative to the synthetic antioxidants currently used in the food industry., Este trabajo ha sido financiado por el proyecto 0011-1408-2017-000023 de convocatoria de Doctorados Industriales 2018-2020 de Gobierno de Navarra., Programa de Doctorado en Agroalimentación (RD 99/2011), Nekazaritzako Elikagaietako Doktoretza Programa (ED 99/2011)
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Tesis doctoral (DoctoralThesis)

Dimensionado y gestión energética de sistemas fotovoltaicos con almacenamiento para autoconsumo residencial

  • Galilea Gil, Carlos
El incremento del precio de la electricidad, el abaratamiento de la energía solar fotovoltaica y de los sistemas de almacenamiento, unido a las políticas de fomento de la energía limpia, han hecho especialmente atractivo en España el autoconsumo fotovoltaico en todos los sectores, incluido el residencial, sector en que se centra esta tesis. Aunque el autoconsumo fotovoltaico permite reducir notablemente el importe de las facturas eléctricas de los propietarios, no está clara cuál es la mejor forma de dimensionar estos sistemas cuando se introduce el uso de almacenamiento energético, generalmente en forma de baterías de iones de litio. Además, la batería introduce un nuevo grado de libertad que permite diseñar estrategias de gestión que garanticen un cierto beneficio al propietario, a la vez que resulte en unos perfiles de consumo que ayuden a la gestión de la red. En esta tesis se ha analizado, en primer lugar, el marco regulatorio del autoconsumo y la tarificación eléctrica en España, pasando a continuación a abordar los anteriores retos económicos y de integración en red, tomando como punto de partida el análisis de consumo de diferentes viviendas reales y analizando los distintos tipos de perfil. Seguidamente, se ha desarrollado una herramienta de dimensionado de estos sistemas que permite, no solo encontrar la solución óptima económica, sino diferentes soluciones con distintos objetivos. Además, se han analizado las estrategias de gestión del estado del arte y se ha desarrollado una nueva estrategia que permite adaptar el perfil de consumo para ayudar a la integración de la energía fotovoltaica en la red, manteniendo a su vez un compromiso de viabilidad económica para el propietario, estrategia que ha sido validada experimentalmente en una microrred a escala real, perteneciente al Laboratorio de Almacenamiento y Microrredes de la Universidad Pública de Navarra., The increase in electricity prices, the lower cost of photovoltaic solar energy and storage systems, together with policies to promote clean energy, have made photovoltaic self-consumption particularly attractive in Spain in all sectors, including the residential sector, which is the focus of this thesis. Although photovoltaic self-consumption can significantly reduce the electricity bills by itself, it is not clear how best to size these systems when the use of energy storage is introduced, generally in the form of lithium-ion batteries. In addition, the battery introduces a new degree of freedom that allows the design of energy management strategies that guarantee a certain benefit to the homeowner while resulting in consumption power profiles that benefit the grid management. In this thesis, firstly, the regulatory framework of self-consumption and electricity pricing in Spain has been analyzed, and then the previous economic and grid integration challenges have been addressed, taking as a starting point the analysis of the power profiles of several consumers, and analyzing and categorizing the different types of profiles. Then, a sizing tool for these systems has been developed, which allows, not only to find the optimal economic solution, but also different solutions with different objectives. In addition, state-of-the-art management strategies have been analyzed and a new strategy has been developed to adapt the consumption profile to help in the integration of photovoltaic energy into the grid, while maintaining a reasonable economic gain for the owner; a strategy that has been experimentally validated in a full-scale microgrid, belonging to the Storage and Microgrids Laboratory of the Public University of Navarra., Esta tesis ha sido financiada por el Gobierno de Navarra y la Universidad Pública de Navarra bajo el proyecto estratégico de I+D 2017-2019 'Almacenamiento Renovable Avanzado de Litio para Autoconsumo Residencial (ARALAR)' (0011-1411-2017-000021), y por el programa de Formación de Personal Investigador (FPI) de la Universidad Pública de Navarra, a través de un contrato predoctoral., Tecnologías de las Comunicaciones, Bioingeniería y de las Energías Renovables (RD 99/2011), Bioingeniaritzako eta Komunikazioen eta Energia Berriztagarrien Teknologietako Doktoretza Programa (ED 99/2011)
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Tesis doctoral (DoctoralThesis)

Novel contactless haptic technologies for creating affective tactile sensations when interacting with computer systems, Tecnologías hápticas sin contacto novedosas para crear sensaciones táctiles afectivas al interactuar con sistemas informáticos

  • Irisarri Erviti, Josu
Esta tesis doctoral desarrolla y explora nuevas tecnologías hápticas sin contacto para generar sensaciones táctiles en los usuarios a distancia y sin obligarles a llevar dispositivos. De esta forma, se reduce el tiempo de empezar a usar el sistema y se mejora la disponibilidad a utilizar dispositivos públicos. Utilizando hápticas sin contacto, esta tesis también quiere ir más allá del tacto funcional (p.ej., notificaciones o discriminación de objetos) e intenta reproducir algunas experiencias perdidas en entornos virtuales como el tacto afectivo. Por ejemplo, los movimientos de roce en el antebrazo pueden tener un fuerte significado afectivo (caricias) pero la tecnología de ultrasonidos focalizados actual no estimula con suficiente intensidad estas áreas de piel. Sin embargo, otras tecnologías sin contacto, como la luz infrarroja o la electrostática podrían generar estas sensaciones afectivas. Los sentidos visual y auditivo han dominado los sistemas de interacción humano-ordenador, a veces desatendiendo el sentido del tacto. En este trabajo, se presentan tecnologías hápticas que pueden proporcionar sensaciones táctil a distancia. Tienen el potencial de mejorar las experiencias inmersivas en entornos virtuales, así como de facilitar una conexión más profunda entre sus usuarios. Esta tesis también explora brevemente el uso de la háptica sin contacto para experiencias multimodales, tecnologías sin contacto y computación afectiva. En primer lugar, la tesis desarrolla una técnica híbrida, un material inteligente que es una combinación de termoplástico y polvo de hierro que se puede activar a distancia mediante calor y campos magnéticos, pero el usuario sigue necesitando contacto directo con el material. Se pensó que este sistema sería la base para comparaciones. En segundo lugar, se presenta una demostración utilizando electrostática para crear piloerección en el antebrazo. Esta tecnología puede actuar a distancia y tiene el potencial de crear estímulos afectivos. En tercer lugar, se combinan el plasma eléctrico y el ultrasonido para guíar chispas eléctricas en el aire, capaz de generar estímulos fuertes y con una buena resolución espacial y temporal. Finalmente, se explican combinaciones aún inacabadas de tecnologías; como ultrasonido, electrostática, chispas eléctricas, aerosoles, luz infrarroja, cambio de humedad/temperatura, aire y láseres. Espero que este trabajo sirva para introducir otras tecnologías hápticas sin contacto distintas de los ultrasonidos, que ha sido la tecnología dominante en la última década. Tener disponibles más tecnologías hápticas sin contacto, puede motivar la incorporación de feedback táctil en algunos sistemas de interacción entre humanos-computadoras, como las experiencias interactivas públicas en exposiciones, museos o teatros., This doctoral thesis develops and explores new contactless haptic technologies to generate tactile sensations on users from a distance and without forcing them to wear devices. Thus, the setup time is reduced and the reluctance towards using public devices is lowered.Moreover, using contactless haptics, this thesis aims to go beyond functional touch (e.g., notifications or object discrimination) and tries to reproduce some experiences lost on virtual environments such as affective touch. For example, stroking motions on the forearm can carry strong affective meaning (caresses) but current focused ultrasound does not stimulate with enough intensity these nonglabrous skin areas. However, other contactless technologies, such as infrared light or electrostatics could generate these affective sensations. Traditionally, visual and auditory senses have dominated human-computer interaction systems, sometimes overshadowing the sense of touch. In this work, emergent haptic technologies that can deliver tactile feedback from a distance are presented. They hold the potential to enhance immersive experiences in virtual environments, as well as facilitate a deeper connection between their users. This thesis also briefly explores the use of contactless haptics for multimodal experiences, touch-free technologies and affective computing. Firstly, the thesis develops a hybrid technique, a smart material that is a combination of thermoplastic and iron powder that can be actuated from a distance using heat and magnetic fields, yet the user still needs direct contact with the material. This systemwas thought to be the baseline for comparisons. Secondly, a demonstration using electrostatics to create piloerection on the forearm is presented. This technology can act at a distance and has the potential to create affective stimuli. Thirdly, electric plasma and ultrasound are put together to show a guidance system for electric sparks in mid-air, capable of strong stimuli as well as high spatial and temporal resolution. Finally, yet unfinished combinations of technologies are explained; such as ultrasound, electrostatics, electric sparks, aerosols, infrared light, humidity/temperature change, air blowing and lasers. I expect thiswork to introduce other technologies for contactless haptics different from ultrasound, which has been the dominant technology in the past decade. More contactless haptics can motivate the addition of tactile feedback in some human-computer interactive systems like public experiences such as exhibitions, museums or theaters., Government of Navarre (FEDER) (0011-1365-2019-000086) and EU Horizon 2020 research and innovation programme (Nº 101017746 TOUCHLESS), Programa de Doctorado en Ciencias y Tecnologías Industriales (RD 99/2011), Industria Zientzietako eta Teknologietako Doktoretza Programa (ED 99/2011)
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Tesis doctoral (DoctoralThesis)

Development of α’-hydroxy enones as Michael acceptors for organocatalytic enantioselective conjugate addition of aldehydes and α-branched nitroalkanes

  • Lorea Revilla, Beñat
The development of catalyst-controlled enantioselective conjugate addition methods has experienced spectacular progress nowadays, in part due to implementation of organocatalytic activation strategies, both covalent and non-covalent. Despite huge advances in the field, state of the art methods still present limitations and as such cannot address every single synthetic challenge. For example, while nitroalkenes have been widely used as Michael acceptors in a wide variety of organocatalytic enantioselective conjugate additions, other acceptors such as α,β- unsaturated carbonyl compounds have been less commonly used, probably due to their lower reactivity. Among them, simple acrylates in general lack reactivity in the addition of nucleophiles, making it necessary to prepare and use more reactive acrylates or to employ more elaborate catalysts that lead to a greater activation of this acceptor. On the other hand, the Michael addition involving nitro-containing compounds as donors has been widely explored due to the versatility of the nitro group, which can be afterwards transformed into numerous functionalities. However, the asymmetric Michael addition of α-branched nitroalkanes is still a challenging reaction because this substitution generates steric hindrance that obstructs both deprotonation and the approach to the acceptor. Furthermore, a new quaternary stereocenter is formed in the reaction, which makes the stereocontrol more challenging. Moreover, in the few examples of additions of asymmetric α-branched nitroalkanes to enones reported, the nitroalkanes bear an electron-ithdrawing group at the alpha position. Presumably, the higher acidity of this kind of nitro compounds and their aptitude for catalyst two-point binding are critical for success. We hypothesized that purposely designing α’-hydroxy enones acting as acrylate surrogates may serve to solve some of the above limitations owing to their reactivity and coordinating ability, as it has been previously disclosed by our laboratory. Thus, several α’-hydroxy enones bearing different substituents at Cα’ were prepared and tested in the Michael reactions of aldehydes and α-branched nitroalkanes. In this Doctoral Thesis we have demonstrated that in contrast to simple enones, which usually require additional activation by an external H-bond donor additive or cocatalyst, α’-hydroxy enones react with enolizable aldehydes in the presence of commercially available diphenylprolinol ether catalysts (C1 or C3) as the only promoters affording adducts bearing a tertiary stereocenter, in good yields (up to 82%) and high enantioselectivity (up to 97:3 er) (Scheme 1). Ulterior transformation of adducts into carboxylic acids, ketones and aldehyde building blocks, was also carried out. Additionally, in this study we show the Michael-type enantioselective organocatalytic addition of several asymmetric α-methyl nitroalkanes to different α’-hydroxy enones using N,Ndiacylaminals (developed by our groups and successfully used in various carbon-carbon bond formation reactions) as Brønsted base/hydrogen bond catalysts (Scheme 2). α’-Hydroxy enone bearing geminal 3,5-bis(trifluoromethyl)phenyl groups showed the greatest reactivity with several α-methyl nitroalkanes at 0 °C in presence of C17 (20 mol%), achieving the products in good yield (up to 82%) and high enantiomeric ratio (up to 96:4). The elaboration of adducts into carboxylic acid, ketone, aldehyde and nitrile functionalities was also successfully assessed., Concesión de una beca predoctoral del Gobierno de Navarra (expediente 0011-0537-2019-000009)., Programa de Doctorado en Química Sintética e Industrial (RD 99/2011), Kimika Sintetiko eta Industrialeko Doktoretza Programa (ED 99/2011)
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Tesis doctoral (DoctoralThesis)

Enhancing semantic segmentation models for high-resolution satellite imagery, Mejora de modelos de segmentación semántica para imágenes satelitales de alta resolución

  • Ayala Lauroba, Christian
El objetivo principal de esta memoria es estudiar, desarrollar y evaluar de manera justa modelos de segmentación semántica que utilicen datos con una resolución espacial limitada para abordar tareas que demandan un alto nivel de detalle, como la segmentación semántica de edificios y carreteras, aprovechando la disponibilidad de datos públicos y de libre acceso. De esta forma se busca reducir la brecha con productos de muy alta resolución, que actualmente son inaccesibles para la gran mayoría de usuarios. La memoria está organizada en torno a cuatro grandes objetivos, cada uno correspondiente a un problema abierto expuesto en la sección anterior, y que en conjunto abordan el objetivo principal mencionado: Estudiar y desarrollar modelos de segmentación semántica para abordar problemas que requieren de un alto nivel de detalle, como la segmentación de edificios y carreteras, utilizando imágenes satelitales de baja resolución espacial. Dados los numerosos métodos existentes en la literatura para segmentar edificios y carreteras [ZLW18, BHF+19,W+20, SZH+21], nos planteamos realizar un estudio de estas técnicas con el objetivo de identificar sus limitaciones y los problemas que puedan surgir al aplicarlas a imágenes satelitales de baja resolución, como las ofrecidas por los satélites Sentinel. Basándonos en esta información, planeamos diseñar un nuevo modelo de aprendizaje profundo capaz de extraer edificios y carreteras a partir de imágenes de baja resolución, con una calidad cercana a la obtenida a partir de imágenes de muy alta resolución. Investigar cuál es la mejor estrategia para abordar problemas de segmentación semántica con múltiples clases. Habitualmente, los problemas de segmentación semántica multi-clase se afrontan de manera directa [YRH18]. Sin embargo, en un contexto donde la resolución espacial influye significativamente en la separación de las clases, parece lógico recurrir a estrategias de descomposición binaria [LdCG09] o esquemas de entrenamiento multi-tarea [Gir15]. Estos enfoques podrían simplificar el problema multi-clase y, por tanto, mejorar la clasificación. No obstante, en el ámbito de la observación de la Tierra, estas estrategias no han sido ampliamente utilizadas en problemas de segmentación semántica. Por ello, nos proponemos llevar a cabo un estudio comparativo de las diferentes estrategias para abordar problemas de segmentación semántica con varias clases en el ámbito de la teledetección, con el objetivo de establecer pautas claras al respecto. Diseñar nuevas técnicas de aumento de datos que exploten la alta periodicidad que ofrecen los satélites de baja resolución. Las técnicas de aumento de datos basadas en fotometría aplicadas al ámbito de la observación de la Tierra presentan limitaciones importantes, como la generación de artefactos sintéticos y la incapacidad de modelar eventos como la siembra, cosecha o la posición del sol [GSD+20]. Además, estas técnicas se encuentran estrechamente ligadas a sensores ópticos, por lo que no son extrapolables a otros tipos de sensores como térmicos o radar. Por ello, nos plantemos proponer formas de explotar la alta periodicidad provista por los satélites de baja resolución como técnica de aumento de datos, sin necesidad de etiquetar estos datos previamente. Establecer pautas para comparar mapas de segmentación semántica a múltiples resoluciones. Dado que en literatura no existe un consenso sobre cómo se deben comparar métricas obtenidas a partir de modelos de segmentación semántica con resoluciones espaciales diferentes, nos planteamos estudiar las limitaciones y ventajas de cada una de las aproximaciones existentes para poder plantear pautas claras que indiquen cuál es la forma correcta de llevar a cabo dicha comparación., Esta tesis ha sido financiada bajo el programa de doctorados industriales 2020 del Gobierno de Navarra. Ref. 0011-1408-2020-000008., Programa de Doctorado en Ciencias y Tecnologías Industriales (RD 99/2011), Industria Zientzietako eta Teknologietako Doktoretza Programa (ED 99/2011)
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Tesis doctoral (DoctoralThesis)

Safety characterization and early detection of thermal runaway in lithium-ion batteries, Caracterización de la seguridad y detección temprana del thermal runaway en baterías de iones de litio

  • Lalinde Sainz, Iñaki
En el actual contexto de emergencia climática, la transición energética global avanza de forma decidida hacia un modelo sostenible, en el que las energías renovables lideran la generación de electricidad limpia. No obstante, su naturaleza intermitente y no gestionable plantea importantes retos para su integración masiva en la red eléctrica. En este escenario, los sistemas de almacenamiento de energía se presentan como una solución clave para garantizar la estabilidad y flexibilidad del sistema. Paralelamente, la expansión del vehículo eléctrico ha acelerado el desarrollo y despliegue de las baterías de iones de litio, consolidándolas como la tecnología de almacenamiento predominante tanto en aplicaciones estacionarias como en movilidad. Sin embargo, a pesar de sus numerosas ventajas, la seguridad sigue siendo el principal desafío por resolver. Fallos asociados al fenómeno de thermal runaway pueden provocar la destrucción total de la batería y generar situaciones de peligro, como incendios o explosiones. Estos riesgos representan una barrera crítica para la consolidación definitiva de esta tecnología como una solución de almacenamiento de energía fiable y segura. Esta tesis se centra en el análisis de la seguridad de las baterías de iones de litio, con especial énfasis en la detección temprana del fenómeno de termal runaway. Para ello, las principales líneas de investigación son: . Revisión del estado del arte actual del fenómeno de thermal runaway en las baterías de iones de litio. . Realización de exhaustivas pruebas de abuso de baterías de iones de litio en diversas condiciones de estrés. . Desarrollo de una metodología para la caracterización de la seguridad de baterías de iones de litio, basada en la identificación de las áreas de abuso. . Análisis y evaluación de indicadores clave para la detección temprana del thermal runaway., In the current climate emergency context, the global energy transition is decisively shifting towards a sustainable model, with renewable energy sources leading the way in clean electricity generation. However, their intermittent and unmanageable nature poses major challenges for large-scale grid integration. In this scenario, energy storage systems are essential to ensure grid stability and operational flexibility. At the same time, the rapid expansion of electric vehicles has driven the development and deployment of lithium-ion batteries, establishing them as the leading storage technology in both stationary and mobility applications. However, despite their many advantages, safety remains the main challenge to be addressed. Failures associated with the thermal runaway phenomenon can result in the complete destruction of the battery and trigger hazardous events such as fires or explosions. These safety concerns constitute a critical barrier to the full consolidation of this technology as a reliable and secure energy storage solution. This thesis focuses on the safety analysis of lithium-ion batteries, with particular emphasis on the early detection of the thermal runaway phenomenon. To this end, the main research lines are: . Review of the current state of the art on thermal runaway phenomenon in lithium-ion batteries. . Execution of comprehensive abuse testing of lithium-ion batteries under various stress conditions. . Development of a methodology for the safety characterization of lithiumion batteries, based on the identification of abuse areas. . Analysis and evaluation of key indicators for the early detection of thermal runaway., This work has been funded by the Public University of Navarre through a doctoral scholarship given by the Spanish Ministry of Science and Innovation (PRE2020-095314). The company Ingeteam Power Technology has supported this investigation under contract OTRI 2021 901 108. Moreover, this research is part of the projects PID2022-139914OB-I00, funded by MICIU/AEI/10.13039/501100011033/ and by ERDF/EU, TED2021-132457BI00, funded by MICIU/AEI/10.13039/501100011033/ and by the European Union “NextGenerationEU/PRTR”, STARDUST (H2020-SCC-2016/17-774094), funded by the European Union’s Horizon 2020 research and innovation program, HYBPLANT (0011-1411-2022-000039), funded by the Government of Navarre., Programa de Doctorado en Tecnologías de las Comunicaciones, Bioingeniería y de las Energías Renovables (RD 99/2011), Bioingeniaritzako eta Komunikazioen eta Energia Berriztagarrien Teknologietako Doktoretza Programa Ofiziala (ED 99/2011)