Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Effect of precursor concentration, surfactant and temperature on the size, morphology and nanostructure of zero-valent iron nanocrystals synthesised by a polyol route

  • Díaz-Ufano, Carlos
  • Morales, María Del Puerto
  • Veintemillas-Verdaguer, S.
Iron metal nanoparticles, due to their magnetic properties, reducing power and low toxicity, have numerous applications not only in groundwater and contaminated soil remediation but also in biomedicine as contrast agents in magnetic resonance imaging. However, obtaining this nanomaterial involves the use of strongly reducing, polluting and expensive reagents and high temperatures. Herein, the use of ethylene glycol and diethylene glycol in a strong alkaline medium that allows the direct reduction of iron(II) salts to iron(0) in the absence of any added reducer has been analysed for preparation of well-defined nanoparticles. The key roles of the polyhydroxylated surfactants (D-mannitol, D-mannose, polyvinyl alcohol and polyvinyl pyrrolidone) were identified, and their efficiencies were evaluated. In addition, conclusions have been drawn regarding the existence of a minimum temperature required for the reduction of the precursor, as well as the observation that the size of the nanoparticles increases with reaction temperature. The main result is that by combining surfactants and controlling the reaction temperature, pure cubic iron(0) nanoparticles smaller than 100 nm were obtained, thereby reducing the formation of hydroxylated by-products. The high reactivity, high magnetic response, long-term stability and small size of the iron nanoparticles produced in this work will allow their use in various applications., This research was funded by the Spanish Ministry of Science, grant number PID2020-13480RB-I00 and TED2021-130191B-C43, and by the EU-commission, H2020-MSCA-RISE-2020 (NESTOR) PROJECT No.101007629 and HORIZON-CL4-2021-DIGITAL-EMERGING-01 (HyPELignum), PROJECT No.101070302 (2022\u201326)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Zero-Valent Iron Nanocatalysts via Polymers or Metal Hydroxide Passivation: Implications for Advanced Oxidation Processes

  • Díaz-Ufano, Carlos
  • Nuñez, Nahuel
  • Gallo-Cordova, Álvaro
  • Winkler, Elin L
  • Morales, María Del Puerto
  • Veintemillas-Verdaguer, S.
Zero-valent iron (ZVI) nanocatalysts are promising materials for environmental remediation (e.g., wastewater treatment) via advanced oxidation processes (AOPs) due to their ability to generate reactive oxygen species (ROS). However, their high reactivity often leads to rapid surface oxidation and a limited stability. This study evaluates the effect of different surface coatings on the stability and ROS production of ZVI nanocatalysts. The coatings tested include organic molecules such as mannitol and polyvinylpyrrolidone (PVP), as well as combinations with thin layers of metal hydroxides (M-(OH)2, where M = Ni or Mn). Hydroxyl radical (•OH) generation was quantified using electron paramagnetic resonance (EPR) spectroscopy over a period of 0 to 7 days in acetate buffer (pH 5). Results show that incomplete PVP coverage leads to a 90% decrease in ROS production within 24 h, while full coverage preserves catalytic activity for at least 1 day. Among inorganic coatings, Mn-(OH)2 maintained stable ROS generation for 7 days, whereas Ni-(OH)2 showed significant degradation after 24 h. These findings highlight the importance of coating selection and surface passivation to enhance ZVI stability and extend its catalytic performance in AOP applications, providing design guidelines for nanocatalysts in Fenton-like processes for water purification and environmental remediation., This research was funded by the MICIU/AEI/10.13039/501100011033, the EU-NextGenerationEU/PRTR project TED2021-130191B-C43, and the EU-commission, H2020-MSCA-RISE-2020 (NESTOR) PROJECT No. 101007629 and HORIZON-CL4-2021-DIGITAL-EMERGING-01 (HyPELignum) PROJECT No. 101070302 (2022–26). Authors also acknowledge the Severo Ochoa Centres of Excellence program through grant CEX2024-001445-S., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Copper-Based Conductive Nanoinks: Scalable Synthesis via Continuous-Flow Microwave-Assisted Polyol Process

  • Santana-Otero, Antonio
  • Fernández-Afonso, Yilian
  • Salvador, María
  • Van Zomeren, A.
  • Bertran-Llorens, S.
  • Morales, María Del Puerto
  • Veintemillas-Verdaguer, S.
Metallic copper nanoparticles are a promising alternative to gold and silver in printed electronics due to their excellent electrical and thermal conductivity. However, their synthesis is often hindered by rapid oxidation and limited scalability. This work presents a microwave-assisted polyol process for the rapid and scalable production of metallic Cu micro- and nanoparticles, performed in air without the need for an inert atmosphere. Ethylene glycol acts as both solvent and reducing agent, while lignin serves as a renewable capping agent. Reaction time is reduced to 10 min in batch mode, and the process is scaled up to a continuous-flow microwave system, achieving production rates of ~5 g h−1. Particle sizes range from 800 to 40 nm depending on lignin content and metal seeding. After pressure or low-temperature (150 °C) treatment, the materials reach conductivities between 30 and 100 μΩ·cm. These metallic copper nanoparticles show strong potential for use in sustainable conductive inks for flexible and printed electronics. © 2025 The Author(s). Energy & Environmental Materials published by John Wiley & Sons Australia, Ltd on behalf of Zhengzhou University., European Union’s Horizon Europe. Grant Agreement no. 101070302 HyPELignum, Peer reviewed