Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 5
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Research, selection, and validation of sustainable reinforcement fibers for use in composites intended for: automotive, infrastructure, and aeronautics

  • Doménech, Iván
  • Santamaría, Carlos
  • Pascual-Bernabeu, José Javier
[EN] Under the coordination of AITEX and in collaboration with the partners of the r-LightBioCom project, intensive research, selection, and validation of sustainable reinforcement fibers (natural, recyclable or recycled, and with low environmental impact) have been carried out for use in composites that will be validated in automotive demonstrators (spoiler and trunk floor), infrastructure (tunnel lining), and aeronautics (wing leading edge). In this area, the following achievements stand out: 1.Validation procedure regarding processability and mechanical characteristics of various sustainable reinforcement fibers (recycled carbon and glass fibers, natural fibers, basalt fiber, and recycled aramid fiber). 2.Development of sustainable textile intermediates (fabrics, mats, pre-pregs, honeycombs, and rovings) through the adaptation of textile technologies for processing the selected reinforcement fibers and compatible with bio-based resins. 3.Hybridization of sustainable reinforcement fibers with virgin filaments to improve mechanical properties while maintaining low environmental impact. The results obtained indicate that the selection of alternative and more sustainable fibers than those usually used in the production of composites are suitable for the development of the aforementioned demonstrators in terms of processability and resistance. The results obtained indicate that the selection of alternative and more sustanaible fibers than those usually used in the production of composites are suitable for the develpment of the aforementioned demonstrators in terms of processability and resistance., Financiado por la Unión Europea bajo el Acuerdo de Subvención Proyecto No 101091691. Las opiniones y puntos de vista expresados son únicamente de los autores y no reflejan necesariamente los de la Unión Europea. La Unión Europea no se hace responsable de ellos.
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Continuous sonochemical nanotransformation of lignin - process design and control

  • Pérez Rafael, Silvia|||0000-0001-9658-6090
  • Ferreres Cabanes, Guillem|||0000-0003-3138-8506
  • Kessler, Rudolf
  • Kessler, Waltraud
  • Blair González, Jeniffer|||0000-0002-8472-1889
  • Rathee, Garima
  • Morena, Angela Gala
  • Tzanov, Tzanko|||0000-0002-8568-1110
As the most abundant renewable aromatic polymer on the planet, lignin is gaining growing interest in replacing petroleum-based chemicals and products. However, only <5 % of industrial lignin waste is revalorized in its macromolecular form as additives, stabilizing agents or dispersant and surfactants. Herein, revalorization of this biomass was achieved by implementing an environmentally-friendly continuous sonochemical nano- transformation to obtain highly concentrated lignin nanoparticles (LigNPs) dispersions for added-value material applications. With the aim to further model and control a large-scale ultrasound-assisted lignin nano- transformation, a two-level factorial design of experiment (DoE) was implemented varying the ultrasound (US) amplitude, flow rate, and lignin concentration. Size and polydispersity measurements together with the UV–Vis spectra of lignin recorded at different time intervals of sonication allowed to monitor and understand the sonochemical process on a molecular level. The light scattering profile of sonicated lignin dispersions showed a significant particle size reduction in the first 20 min, followed by moderate particle size decrease below 700 nm until the end of the 2 h process. The response surface analysis (RSA) of the particle size data revealed that the lignin concentration and sonication time were the most important factors to achieve smaller NPs. From a mechanistic point of view, a strong impact of the particle–particle collisions due to sonication seems to be responsible for the decrease in particle size and homogenization of the particle distribution. Unexpectedly, a strong interaction between the flow rate and US amplitude on the particle size and nanotransformation efficiency was observed, yielding smaller LigNPs at high amplitude and low flow rate or vice versa. The data derived from the DoE were used to model and predict the size and polydispersity of the sonicated lignin. Furthermore, the use of the NPs spectral process trajectories calculated from the UV–Vis spectra showed similar RSA model as the dynamic light scattering (DLS) data and will potentially allow the in-line monitoring of the nanotransformation process., This research was funded by the European Union under the framework of the projects BIOMAT (H2020-953270) and rLightBioCom (HORIZON-101091691). G. F. acknowledges Universitat Politècnica de Catalunya and Banco Santander for his PhD grant (113 FPI-UPC 2018)., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Influence of enzymatically hydrophobized hemp protein on morphology and mechanical properties of bio-based polyurethane and epoxy foams

  • Ferreres Cabanes, Guillem|||0000-0003-3138-8506
  • Pérez Rafael, Silvia|||0000-0001-9658-6090
  • Morena Gatius, Ángela Gala|||0000-0003-4470-8249
  • Tzanov, Tzanko|||0000-0002-8568-1110
  • Gryshchuk, Liudmyla
Biomass fillers offer the possibility to modify the mechanical properties of foams, increasing their cost-effectiveness and reducing their carbon footprint. In this study, bio-based PU (soft, open cells for the automotive sector) and epoxy (EP, hard, closed cells for construction applications) composite foams were prepared by adding pristine and laccase-mediated lauryl gallate-hydrophobized hemp protein particles as filler (HP and HHP, respectively). The fillers were able to modify the density, the mechanical properties and the morphology of the PU and EP foams. The addition of HP filler increases the density of PU foams up to 100% and significantly increases the s values by 40% and Emod values. On the other hand, the inclusion of the HHP as filler in PU foams mostly results in reduced density, by almost 30%, and reduced s values in comparison with reference and HP-filled foams. Independently from filler concentration and type, the biomass increased the Emod values for all foams relative to the reference. In the case of the EP foams, the tests were only conducted for the foams filled with HHP due to the poor compatibility of HP with the EP matrix. HHP decreased the density, compressive strength and Emod values of the composites. For both foams, the fillers increased the size of the cells, while reducing the amount of open cells of PU foams and the amount of closed cells for EP foams. Finally, both types of foams filled with HHP reduced the moisture uptake by 80 and 45%, respectively, indicating the successful hydrophobization of the composites., Peer Reviewed
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Continuous sonochemical nanotransformation of lignin - process design and control

  • Pérez Rafael, Silvia
  • Ferreres Cabanes, Guillem
  • Kessler, Rudolf
  • Kessler, Waltraud
  • Blair González, Jeniffer
  • Rathee, Garima
  • Morena, Angela Gala
  • Tzanov, Tzanko
As the most abundant renewable aromatic polymer on the planet, lignin is gaining growing interest in replacing petroleum-based chemicals and products. However, only <5 % of industrial lignin waste is revalorized in its macromolecular form as additives, stabilizing agents or dispersant and surfactants. Herein, revalorization of this biomass was achieved by implementing an environmentally-friendly continuous sonochemical nano- transformation to obtain highly concentrated lignin nanoparticles (LigNPs) dispersions for added-value material applications. With the aim to further model and control a large-scale ultrasound-assisted lignin nano- transformation, a two-level factorial design of experiment (DoE) was implemented varying the ultrasound (US) amplitude, flow rate, and lignin concentration. Size and polydispersity measurements together with the UV–Vis spectra of lignin recorded at different time intervals of sonication allowed to monitor and understand the sonochemical process on a molecular level. The light scattering profile of sonicated lignin dispersions showed a significant particle size reduction in the first 20 min, followed by moderate particle size decrease below 700 nm until the end of the 2 h process. The response surface analysis (RSA) of the particle size data revealed that the lignin concentration and sonication time were the most important factors to achieve smaller NPs. From a mechanistic point of view, a strong impact of the particle–particle collisions due to sonication seems to be responsible for the decrease in particle size and homogenization of the particle distribution. Unexpectedly, a strong interaction between the flow rate and US amplitude on the particle size and nanotransformation efficiency was observed, yielding smaller LigNPs at high amplitude and low flow rate or vice versa. The data derived from the DoE were used to model and predict the size and polydispersity of the sonicated lignin. Furthermore, the use of the NPs spectral process trajectories calculated from the UV–Vis spectra showed similar RSA model as the dynamic light scattering (DLS) data and will potentially allow the in-line monitoring of the nanotransformation process., This research was funded by the European Union under the framework of the projects BIOMAT (H2020-953270) and rLightBioCom (HORIZON-101091691). G. F. acknowledges Universitat Politècnica de Catalunya and Banco Santander for his PhD grant (113 FPI-UPC 2018)., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Influence of enzymatically hydrophobized hemp protein on morphology and mechanical properties of bio-based polyurethane and epoxy foams

  • Ferreres Cabanes, Guillem
  • Pérez Rafael, Silvia
  • Morena Gatius, Ángela Gala
  • Tzanov, Tzanko
  • Gryshchuk, Liudmyla
Biomass fillers offer the possibility to modify the mechanical properties of foams, increasing their cost-effectiveness and reducing their carbon footprint. In this study, bio-based PU (soft, open cells for the automotive sector) and epoxy (EP, hard, closed cells for construction applications) composite foams were prepared by adding pristine and laccase-mediated lauryl gallate-hydrophobized hemp protein particles as filler (HP and HHP, respectively). The fillers were able to modify the density, the mechanical properties and the morphology of the PU and EP foams. The addition of HP filler increases the density of PU foams up to 100% and significantly increases the s values by 40% and Emod values. On the other hand, the inclusion of the HHP as filler in PU foams mostly results in reduced density, by almost 30%, and reduced s values in comparison with reference and HP-filled foams. Independently from filler concentration and type, the biomass increased the Emod values for all foams relative to the reference. In the case of the EP foams, the tests were only conducted for the foams filled with HHP due to the poor compatibility of HP with the EP matrix. HHP decreased the density, compressive strength and Emod values of the composites. For both foams, the fillers increased the size of the cells, while reducing the amount of open cells of PU foams and the amount of closed cells for EP foams. Finally, both types of foams filled with HHP reduced the moisture uptake by 80 and 45%, respectively, indicating the successful hydrophobization of the composites., Peer Reviewed, Postprint (published version)