Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 6
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

New characterization methodology for vapor-injection scroll compressors

  • Tello-Oquendo, Fernando M.
  • Navarro-Peris, Emilio|||0000-0002-0608-2129
  • Gonzálvez-Maciá, José|||0000-0001-9422-7756
[EN] This paper presents a characterization methodology for vapor-injection scroll compressors (SCVI). An SCVI was characterized in a modified calorimetric test bench, which is able to control the intermediate pressure and the injection superheat independently. Based on the characterization results, the injection mass flow rate was correlated with the intermediate pressure through a linear expression, and a modified AHRI polynomial was proposed to estimate the compressor power input. The correlations were used in a simple model to predict the intermediate conditions of the SCVI installed in a heat pump prototype with an economizer. The deviations obtained for the evaporator mass flow rate, injection mass flow rate, intermediate pressure, and compressor power input were lower than 5% in all cases. The proposed methodology allows evaluating SCVI in a wide range of operating conditions, being only dependent on compressor characteristics and totally independent of the system in which it is installed., Fernando M. Tello-Oquendo acknowledges the financial support provided by the "CONVOCATORIA ABIERTA 2013-SEGUNDA EASE" program, which was funded by the SENESCYT ("Secretaria Nacional de Educacion Superior, Ciencia, Tecnologia e Innovacion") (Grant No. 2015-AR37665) of Ecuador.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Contribución de congreso (ConferenceOutput)

Theoretical comparison of the performance of two-stage reciprocating compressor, a two-stage scroll compressor, and a vapor-injection scroll compressor

  • Tello-Oquendo, Fernando M.
  • Navarro-Peris, Emilio|||0000-0002-0608-2129
  • Gonzálvez-Maciá, José|||0000-0001-9422-7756
[EN] Vapor-injection technique comprises the injection of vapor refrigerant into an intermediate stage of compression. This technique is used in refrigeration systems and heat pumps working in extreme conditions. The advantages of vapor-injection are the improvement of capacity and COP in severe climates and the reduction of the compressor discharge temperature. The vapor-injection scroll compressor (SCVI) is one of the most frequently used compressors in heat pump systems with vapor-injection technique. In this case, the refrigerant is injected during the compression process into the scroll chambers. The intermediate pressure and refrigerant flow depend on the compressor design and the injection port size and location. Another common compressor technology with vapor injection is the two-stage reciprocating compressor (TSRC). In this case, the vapor-injection is performed after the first stage of compression. Therefore, the refrigerant discharged for the first stage of compression is mixed with the injection refrigerant before entering the second-stage compressor. The advantage of the scroll technology is the high volumetric efficiency for all compressor-working envelope, and it has a good compressor efficiency for moderate pressure ratios (< 7). On the other hand, the reciprocating compressors have a flatter compressor efficiency curve, but the volumetric efficiency rapidly decreases with the pressure ratio. Another possibility of the vapor-injection compressor is the two-stage scroll compressor (TSSC). Nevertheless, there is not a systematic evaluation of the performance of this compressor technology and a comparison with the previously described technologies. This paper presents a performance comparison of three compressor technologies with vaporinjection, two-stage reciprocating compressor, two-stage scroll compressor, and vapor-injection scroll compressor. The comparison is performed in terms of the compressor efficiencies, discharge temperature, heating capacity, and COP. In order to do that, semi-empirical models of the compressors have been implemented for each compressor technology. The models consider the main sources of losses in the compression process and are able to predict the compressor efficiencies in terms of empirical parameters, which have a direct physical interpretation. Results show that SCVI presents better COP and efficiency with pressure ratios below 5; the TSSC and TSRC perform better with higher pressure ratios (above 7), nevertheless the TSSC present higher volumetric efficiency and heating capacity than the TSRC. The irreversibilities in the compression process of the TSSC decrease the compressor efficiency for low and moderate pressure ratios compared with the SCVI., Fernando M. Tello-Oquendo acknowledges the financial support provided by the CONVOCATORIA ABIERTA 2013-SEGUNDA FASE program, which was funded by the SENESCYT (Secretaría de Educación Superior, Ciencia, Tecnología e Innovación) (Grant No 2015-AR37665) of Ecuador. The authors acknowledge the Spanish MINISTERIO DE ECONOMIA Y COMPETITIVIDAD, through the project ref-ENE2017-83665-C2-1-P Maximización de la eficiencia y minimización del impacto ambiental de bombas de calor para la descarbonización de la calefacción/ACS en los edificios de consumo casi nulo for the given support.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Comparison of the performance of a vapor-injection scroll compressor and a two-stage scroll compressor working with high pressure ratios

  • Tello-Oquendo, Fernando M.
  • Navarro-Peris, Emilio|||0000-0002-0608-2129
  • Gonzálvez-Maciá, José|||0000-0001-9422-7756
[EN] This paper presents a comparative analysis of the performance of a vapor-injection scroll compressor (SCVI) and a two-stage scroll compressor (TSSC) working with high pressure ratios in heat pump applications. Semi-empirical models of the compressors are implemented. The models are adjusted with experimental data obtained in a calorimetric test bench. The optimum displacement ratio (DR) is analyzed considering two criteria, COP maximization, and discharge temperature minimization. Once defined the optimum DR, a systematic comparison of the compressors is performed in terms of compressor efficiencies, heating capacity, COP, and discharge temperature. Finally, the intermediate pressure is optimized for a high-temperature water heating application, taking into account heat sink of finite capacity. Results show that the optimum DR of TSSC is around 0.58 and the COP is 6% larger than that the SCVI at the nominal point. Considering a wide range of operating conditions, the SCVI presents better efficiency and COP for pressure ratios below 5. For higher-pressure ratios, the TSSC presents better performance and achieves lower discharge temperature. The heating capacity of the TSSC can be improved by 7% by varying the swept volume of the high-stage compressor compared with the SCVI, with a minimum effect on the COP and on the discharge temperature from the optimum conditions., Fernando M. Tello-Oquendo acknowledges the financial support provided by the CONVOCATORIA ABIERTA 2013-SEGUNDA FASE program, which was funded by the SENESCYT (Secretaría de Educación Superior, Ciencia, Tecnología e Innovación) (Grant No. 2015-AR37665) of Ecuador. The authors would like to acknowledge Emerson Commercial and Residential Solutions for the given support to obtain the experimental data of scroll compressors and testing. In addition, the authors acknowledge the Spanish MINISTERIO DE ECONOMIA Y COMPETITIVIDAD , through the project ref-ENE2017-83665-C2-1-P Maximización de la eficiencia y minimización del impacto ambiental de bombas de calor para la descarbonización de la calefacción/ACS en los edificios de consumo casi nulo for the given support.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Semi-empirical model of scroll compressors and its extension to describe vapor-injection compressors. Model description and experimental validation, Modélisation semi-empirique de compresseurs à spirale et ses extensions pour décrire les compresseurs à injection de vapeur. Description du modèle et la validation expérimentale

  • Tello-Oquendo, Fernando
  • Navarro-Peris, Emilio|||0000-0002-0608-2129
  • Barceló Ruescas, Francisco|||0000-0002-0577-2662
  • Gonzálvez-Maciá, José|||0000-0001-9422-7756
[EN] This paper presents a semi-empirical model of scroll compressors and proposes a methodology in order to extend this model to vapor-injection scroll compressors. The model takes into account the ideal evolution of the refrigerant throughout the compressor and considers the main sources of losses in the compression process. The model is able to predict the compressor and volumetric efficiencies in terms of ten empirical parameters, which have a direct physical interpretation. For the model validation, a series of four non-injected scroll compressors of different capacities were tested using R-290 and a scroll compressor with vapor-injection (SCVI) was characterized using R-407C. Results show a correct agreement between the experimental and calculated compressor efficiencies, with a maximum deviation of ±5%. Furthermore, the model estimates accurately the discharge temperature of the refrigerant, compressor power input, and refrigerant mass flow rate in the suction and injection port. Finally, the SCVI model response was evaluated by varying the intermediate pressure and the injection superheat., Fernando M. Tello-Oquendo acknowledges the financial support provided by the CONVOCATORIA ABIERTA 2013-SEGUNDA FASE program, which was funded by the SENESCYT (Secretaría de Educación Superior, Ciencia, Tecnología e Innovación) (Grant No 2015-AR37665) of Ecuador. The authors would like to acknowledge the Spanish MINISTERIO DE ECONOMIA Y COMPETITIVIDAD , through the project ref-ENE2017-83665-C2-1-P Maximización de la eficiencia y minimización del impacto ambiental de bombas de calor para la descarbonización de la calefacción/ACS en los edificios de consumo casi nulo for the given support.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Tesis doctoral (DoctoralThesis)

Study of scroll compressors with vapor-injection for heat pumps operating in cold climates or in high-temperature water heating applications

  • Tello Oquendo, Fernando Mauricio
[ES] Esta tesis doctoral presenta un estudio de compresores scroll con inyección de vapor (SCVI) para bombas de calor que operan en climas fríos o para aplicaciones de calentamiento de agua a alta temperatura. Para ello, se comparó experimentalmente un SCVI con un compresor de dos etapas de pistones (TSRC) trabajando con R-407C en condiciones extremas. La comparación se realizó en términos de eficiencias del compresor, capacidad, COP y rendimientos estacionales tanto para el modo calefacción como para el modo refrigeración. Los resultados proporcionan una idea general sobre el rango de aplicación de los compresores estudiados y sobre las diferencias en los rendimientos de los compresores. Sin embargo, se identificaron varias limitaciones en la caracterización de los compresores y en el análisis del ciclo. Esto motivó a profundizar en el estudio del ciclo de compresión de dos etapas y sus componentes. El siguiente paso fue realizar un análisis teórico de los ciclos de compresión de dos etapas para aplicaciones de calefacción, en donde se identificó a la presión intermedia y a la relación de inyección como los parámetros del sistema más influyentes sobre el COP. La presión intermedia se optimizó para dos configuraciones de inyección (tanque de separación y economizador) utilizando varios refrigerantes. Basándose en los resultados de la optimización, se propuso una correlación que permite obtener la presión intermedia óptima del ciclo, considerando la influencia del subenfriamiento a la salida del condensador. Además, se analizó la influencia del diseño de los componentes del sistema sobre el COP del ciclo. Posteriormente, el estudio se profundizó a nivel de componentes. El factor más crítico en el sistema es el rendimiento del compresor. Por lo tanto, el siguiente paso fue evaluar la influencia de varios sistemas de compresión con inyección de vapor sobre el COP. Se tomaron en cuenta tres tecnologías de compresores, un SCVI, un TSRC y un compresor scroll de dos etapas (TSSC). Estas tecnologías de compresores fueron caracterizadas y modeladas para estudiar su rendimiento. Para ello, se propuso una nueva metodología para caracterizar compresores scroll con inyección de vapor. Esta metodología permite evaluar el rendimiento del compresor independientemente del mecanismo de inyección que se utiliza en el ciclo. Se identificó una correlación lineal entre la relación de inyección de refrigerante y la relación de compresión intermedia. Esta correlación se utiliza para determinar el flujo másico de inyección en función de la presión intermedia. Posteriormente, se propuso un modelo semi-empírico de compresores scroll y una metodología para extender dicho modelo para compresores scroll con inyección de vapor. Los modelos fueron ajustados y validados usando datos experimentales de cuatro compresores scroll trabajando con R-290 y un SCVI trabajando con R-407C. Finalmente, se comparó un SCVI con dos compresores de dos etapas, un TSSC y un TSRC, trabajando en condiciones extremas. Se optimizó la relación de volúmenes de los compresores de dos etapas. Los resultados muestran que, en las condiciones nominales de funcionamiento (Te=-15 °C, Tc=50 °C), la relación de volúmenes óptima del TSSC es 0.58, y del TSRC es 0.57. El TSSC consigue un COP 6% mayor que el SCVI y un COP 11.7% mayor que el TSRC. Bajo un amplio rango de condiciones de operación, el SCVI presenta una mejor eficiencia y COP para relaciones de presión inferiores a 5. Para relaciones de presión más altas, el TSSC presenta mejor rendimiento y consigue una temperatura de descarga más baja. Se concluye que el SCVI es una solución fácil de implementar, desde el punto de vista del mecanizado, y que permite extender el mapa de trabajo de los compresores de una etapa. Sin embargo, los resultados muestran que la compresión en dos etapas consigue mejorar en mayor medida el COP del ciclo y la capacidad, con una mayor redu, [CA] Aquesta tesi doctoral presenta un estudi de compressors scroll amb injecció de vapor (SCVI) per a bombes de calor que operen en climes freds o per a aplicacions d'escalfament d'aigua a alta temperatura. Per a això, es va comparar experimentalment un SCVI amb un compressor de dues etapes de pistons (TSRC) treballant amb R-407C en condicions extremes. La comparació es va realitzar en termes d'eficiències del compressor, capacitat, COP i rendiments estacionals tant per al mode calefacció com per al mode refrigeració. Els resultats proporcionen una idea general sobre el rang d'aplicació dels compressors estudiats i sobre les diferències en els rendiments dels compressors. No obstant això, es van identificar diverses limitacions en la caracterització dels compressors i en l'anàlisi del cicle. Això va motivar a aprofundir en l'estudi del cicle de compressió de dues etapes i els seus components. El següent pas va ser realitzar una anàlisi teòrica dels cicles de compressió de dues etapes per a aplicacions de calefacció, on es va identificar la pressió intermèdia i la relació d'injecció com els paràmetres del sistema més influents sobre el COP. La pressió intermèdia es va optimitzar per a dues configuracions d'injecció (tanc de separació i economitzador) utilitzant diversos refrigerants. Basant-se en els resultats de l'optimització, es va proposar una correlació que permet obtindre la pressió intermèdia òptima del cicle, considerant la influència del subrefredament a l'eixida del condensador. A més, es va analitzar la influència del disseny dels components del sistema sobre el COP del cicle. Posteriorment, l'estudi es va aprofundir a nivell de components. El factor més crític en el sistema és el rendiment del compressor. Per tant, el següent pas va ser avaluar la influència de diversos sistemes de compressió amb injecció de vapor sobre el COP. Es van prendre en compte tres tecnologies de compressors, un SCVI, un TSRC i un compressor scroll de dues etapes (TSSC). Aquestes tecnologies de compressors van ser caracteritzades i modelades per a estudiar el seu rendiment. Per a això, es va proposar una nova metodologia per a caracteritzar compressors scroll amb injecció de vapor. Aquesta metodologia permet avaluar el rendiment del compressor independentment del mecanisme d'injecció que s'utilitza en el cicle. Es va identificar una correlació lineal entre la relació d'injecció de refrigerant i la relació de compressió intermèdia. Aquesta correlació s'utilitza per a determinar el flux màssic d'injecció en funció de la pressió intermèdia. Posteriorment, es va proposar un model semi-empíric de compressors scroll i una metodologia per a estendre aquest model per a compressors scroll amb injecció de vapor. Els models van ser ajustats i validats utilitzant dades experimentals de quatre compressors scroll treballant amb R-290 i un SCVI treballant amb R-407C. Finalment, es va comparar un SCVI amb dos compressors de dues etapes, un TSSC i un TSRC, treballant en condicions extremes. Es va optimitzar la relació de volums dels compressors de dues etapes. Els resultats mostren que, en les condicions nominals de funcionament (Te=-15 °C, Tc=50 °C), la relació de volums òptima del TSSC és 0.58, i del TSRC és 0.57. El TSSC aconsegueix un COP 6% major que el SCVI i un COP 11.7% major que el TSRC. Sota un ampli rang de condicions d'operació, el SCVI presenta una millor eficiència i COP per a relacions de pressió inferiors a 5. Per a relacions de pressió més altes, el TSSC presenta millor rendiment i aconsegueix una temperatura de descàrrega més baixa. Es conclou que el SCVI és una solució fàcil d'implementar, des del punt de vista del mecanitzat, i que permet estendre el mapa de treball dels compressors d'una etapa. No obstant això, els resultats mostren que la compressió en dues etapes aconsegueix millorar en major mesura el COP del cicle i la capacitat, amb una major reducció de la, [EN] This Ph.D. thesis presents a study of scroll compressors with vapor-injection (SCVI) for heat pumps operating in cold climates or in high-temperature water heating applications. To do so, firstly, an SCVI was experimentally compared with a two-stage reciprocating compressor (TSRC) working with R-407C under extreme conditions. The comparison was made in terms of compressor efficiencies, capacity, COP, and seasonal COP, both for heating and cooling modes. The results give a general idea about the application range of the studied compressors and the differences in the compressors' performance. Nevertheless, several restrictions in the compressors' characterization and the cycle analysis were identified. This motivated us to deepen in the study of the two-stage compression cycle and its components. The next step was performing a theoretical analysis of two-stage compression cycles for heating applications, where the intermediate pressure and the injection ratio were identified as the most influential system parameters on the COP. The intermediate pressure was optimized for two vapor-injection configurations (flash tank and economizer) using several refrigerants. Based on the optimization results, a correlation was proposed that allows obtaining the optimal intermediate pressure of the cycle, considering the influence of the subcooling at the condenser outlet. In addition, a theoretical analysis of the influence of the design of the system components on the COP of the cycle was performed. Once the thermodynamic analysis of the two-stage cycle was carried out, the study was deepened at the component level. The most critical factor in the system is the compressor performance. Hence, the next step was evaluating the influence of several compression systems with vapor-injection on the COP. Three compressor technologies were taken into account, an SCVI, a TSRC and a two-stage scroll compressor (TSSC). These compressor technologies were characterized and modeled in order to study their performance. To do so, a new methodology to characterize SCVI was proposed. This methodology allows evaluating the compressor performance independently of the injection mechanism used in the cycle. A linear correlation was identified between the refrigerant injection ratio and the intermediate compression ratio. This correlation is used to determine the injection mass flow as a function of the intermediate pressure. Then, a semi-empirical model of scroll compressors and a methodology to extend the model for scroll compressors with vapor-injection was proposed. The models were adjusted and validated using experimental data from four scroll compressors working with R-290 and an SCVI compressor working with R-407C. Finally, an SCVI was compared with two two-stage compressors, a TSSC, and a TSRC, working in extreme conditions. The displacement ratio of the two-stage compressors was optimized. Results show that, at the nominal operating conditions (Te=-15 °C, Tc=50 °C), the optimal displacement ratio of the TSSC is 0.58, and of the TSRC is 0.57. The TSSC achieves 6% larger COP than the SCVI and 11.7% larger COP than the TSRC. Under a wide range of operating conditions, the SCVI presents a better efficiency and COP for pressure ratios below 5. For higher-pressure ratios, the TSSC presents better performance and achieves lower discharge temperature. It is concluded that the SCVI is an easy solution to implement from the point of view of machining, which allows extending the working map of the single-stage compressors. However, the results show that the two-stage compression technology gets further improve the COP of the cycle and the capacity, with a greater reduction of the discharge temperature operating under extreme conditions., I thank the financial support provided by the Secretaría de Educación Superior, Ciencia, Tecnología e Innovación (SENESCYT) of Ecuador, through the international scholarship program for postgraduate studies “Convocatoria Abierta 2013 Segunda Fase, Grant No 2015-AR37665”.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

A comprehensive study of two-stage vapor compression cycles with vapor-injection for heating applications, taking into account heat sink of finite capacity

  • Tello Oquendo, Fernando M.
  • Navarro-Peris, Emilio|||0000-0002-0608-2129
  • Gonzálvez-Maciá, José|||0000-0001-9422-7756
[EN] This paper presents a comprehensive study of two-stage vapor compression cycles with vapor-injection for several refrigerants considering that the heat sink has a limited capacity. The key parameters of the cycle performance are identified and the influence of these parameters on the heating COP is analyzed. The optimum intermediate conditions of the cycle are evaluated using a general model of the cycle, considering two configurations (flash tank and economizer). Based on the optimization results, a correlation is proposed in order to estimate the optimum intermediate pressure, taking into account the temperature lift in the secondary fluid imposed by the application. The correlation uses cycle subcooling as an input, which is a novelty from the current correlations proposed in the literature. In addition, an optimum subcooling control strategy is proposed and finally, the influence of the size of the system components on the COP is studied., Fernando M. Tello-Oquendo acknowledges the financial support provided by the CONVOCATORIA ABIERTA 2013-SEGUNDA FASE program, which was funded by the SENESCYT (Secretaria de Educacion Superior, Ciencia, Tecnologia e Innovacion) (Grant no. 2015-AR37665) of Ecuador.