Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 11
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Observador de alta ganancia con zona muerta ajustable para estimar la saturación de agua líquida en pilas de combustible tipo PEM, High gain observer with dynamic deadzone to estimate liquid water saturation in PEM fuel cells

  • Cecilia, A.
  • Costa-Castelló, R.
[EN] In the area of PEM fuel cells, water management remains one of the most challenging issues affecting PEMFC efficiency and lifetime. Liquid water active control and supervision techniques are limited by the absence of online sensors that can estimate the liquid water saturation. For this reason, this work presents the design of a state observer to estimate the cathode catalyst layer's liquid water saturation of an open-cathode PEM fuel cell. The proposed observer is based on High-Gain techniques, and is modified with a dynamic dead-zone which reduces the observer's noise sensibility. The results have been validated through numerical simulation and experiments. It is shown that, in the absence of noise, the proposed observer presents a similar performance than its non dead-zone equivalent. Moreover, in the presence of noise, the dead-zone significantly reduces the estimation error induced by it., [ES] En el campo de las pilas de combustible PEM, la gestión de agua líquida es una de las problemáticas más importantes que afectan a la eficiencia y vida útil del sistema. Las técnicas de control activo y supervisión del agua se ven limitadas por la ausencia de sensores que puedan medir la saturación de agua líquida en línea. Por eso, en este trabajo se presenta el diseño de un observador de estado para la estimación de la saturación de agua líquida en la capa catalizadora del cátodo de una pila de combustible PEM de cátodo abierto. El observador propuesto se basa en técnicas de alta ganancia. Además, se modifica con una función de zona muerta autoajustable con el fin de reducir su sensibilidad al ruido en la medida. Los resultados se han validado mediante simulación numérica y experimentación. Estos muestran que, en ausencia de ruido, el observador propuesto presenta unas prestaciones similares a las de su equivalente sin zona muerta. Además, en presencia de ruido, la zona muerta disminuye significativamente el error de estimación inducido por este., Este proyecto se ha financiado parcialmente por el proyecto DOVELAR (ref. RTI2018-096001-B-C32). Este trabajo se ha realizado con el apoyo de la Agencia Estatal de Investigación española a través del sello de excelencia de María de Maeztu, IRI (MDM-2016-0656). Este trabajo se ha financiado parcialmente por AGAUR of Generalitat de Catalunya a través de la subvención del grupo Advanced Control Systems (SAC) (2017 SGR 482). Este trabajo se ha realizado con el apoyo de ACCIÓ (Operational Program FEDER Catalunya 2014-2020) a través de REFER project (COMRDI15-1-0036-11).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Herramientas para la docencia de control digital en grados de ingeniería, Tools for teaching digital control in engineering degrees

  • Lerma, E.
  • Costa-Castelló, R.
  • Griñó, R.
  • Sanchis, C.
[EN] This work describes a set of teaching materials that have been developed to support the learning of digital control. In particular, it presents a set of interactive tools and the project Duino-Based Learning (DBL) that has been designed to develop experimental practices of digital control using Arduino. In addition, the paper depicts the contents of a digital control course, taught in the framework of an industrial engineering degree, and how the developed tools are used in its teaching., [ES] En este trabajo se describen un conjunto de materiales pedagógicos que han sido desarrollados para dar soporte a la docencia del control digital. En particular, se presentan un conjunto de herramientas interactivas y el proyecto Duino-Based Learning (DBL) pensado para desarrollar prácticas experimentales de control digital utilizando Arduino. Además, se describe el contenido de un curso de control digital, que  se imparte en el marco de una titulación de ingeniería industrial, y como se utilizan las diferentes herramientas desarrolladas en su docencia., El trabajo de E. Lerma ha sido financiado por la donación de Mathworks UPC-I-01523. El trabajo de R. Griñó ha sido parcialmente financiado por el Gobierno de España a través de la Agencia Estatal de Investigación Proyecto DPI2017-85404-P, la Generalitat de Catalunya a través del Proyecto 2017 SGR 872 y la donación de Mathworks UPC-I-01523. El trabajo de R. Costa-Castelló ha sido parcialmente financiado por el Gobierno de España a través de la Agencia Estatal de Investigación Proyecto DOVELAR ref. RTI2018-096001-B-C32 (MCIU/AEI/FEDER, UE) y “María de Maeztu Seal of Excellence to IRI” (MDM-2016-0656), la Generalitat de Catalunya a través del Proyecto 2017 SGR 482 y la donación de Mathworks UPC-I-01523.
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Design of state-feedback controllers for linear parameter varying systems subject to time-varying input saturation

  • Ruiz Royo, Adrián
  • Rotondo, Damiano
  • Morcego Seix, Bernardo
All real-world systems are affected by the saturation phenomenon due to inherent physical limitations of actuators. These limitations should be taken into account in the controller’s design to prevent a possibly severe deterioration of the system’s performance, and may even lead to instability of the closed-loop system. Contrarily to most of the control strategies, which assume that the saturation limits are constant in time, this paper considers the problem of designing a state-feedback controller for a system affected by time-varying saturation limits with the objective to improve the performance. In order to tie variations of the saturation function to changes in the performance of the closed-loop system, the shifting paradigm is used, that is, some parameters scheduled by the time-varying saturations are introduced to schedule the performance criterion, which is considered to be the instantaneous guaranteed decay rate. The design conditions are obtained within the framework of linear parameter varying (LPV) systems using quadratic Lyapunov functions with constant Lyapunov matrices and they consist in a linear matrix inequality (LMI)-based feasibility problem, which can be solved efficiently using available solvers. Simulation results obtained using an illustrative example demonstrate the validity and the main characteristics of the proposed approach., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

An LMI–based heuristic algorithm for vertex reduction in LPV systems

  • Sanjuan Gómez, Adrián
  • Rotondo, Damiano
  • Nejjari Akhi-Elarab, Fatiha
  • Sarrate Estruch, Ramon
The linear parameter varying (LPV) approach has proved to be suitable for controlling many non-linear systems. However, for those which are highly non-linear and complex, the number of scheduling variables increases rapidly. This fact makes the LPV controller implementation not feasible for many real systems due to memory constraints and computational burden. This paper considers the problem of reducing the total number of LPV controller gains by determining a heuristic methodology that combines two vertices of a polytopic LPV model such that the same gain can be used in both vertices. The proposed algorithm, based on the use of the Gershgorin circles, provides a combinability ranking for the different vertex pairs, which helps in solving the reduction problem in fewer attempts. Simulation examples are provided in order to illustrate the main characteristics of the proposed approach., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Active damping of a DC network with a constant power load: an adaptive observer-based design

  • Machado, Juan
  • Ortega, Romeo
  • Astolfi, Alessandro
  • Arocas Pérez, José
  • Pyrkin, Anton
  • Bobtsov, Alexey
  • Griñó Cubero, Robert
© 2019 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting /republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works, This paper proposes a nonlinear, output feedback, adaptive controller to increase the stability margin of a direct-current (DC), small-scale, electrical network containing an unknown constant power load. Due to their negative incremental impedance, constant power loads are known to reduce the effective damping of a network, leading to voltage oscillations and even to network collapse. To overcome this drawback, we consider the incorporation of a controlled DC-DC power converter in parallel with the constant power load. The design of the control law for the converter is particularly challenging due to the existence of unmeasured states and unknown parameters. We propose a standard input-output linearization stage, to which a suitably tailored adaptive observer is added. The good performance of the controller is evaluated with numerical simulations, Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Feedback linearizing control of a magnetically coupled multiport dc-dc converter for automotive applications

  • Olm Miras, Josep Maria
  • Fossas Colet, Enric
  • Repecho del Corral, Víctor
  • Dòria Cerezo, Arnau
  • Griñó Cubero, Robert
© 2019 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting /republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works, This paper presents a feedback linearization-based control strategy for a a magnetically coupled multiport dc-dc converter aimed at automotive applications. Essentially, a transformation of control and state variables is proposed in such a way that the resulting system becomes linear and decoupled. Then, a conventional PI controller is devised that renders asymptotic stability, as well as robustness to resistive load uncertainty and presence of constant power loads. The inversion of the control transformation, which involves nonlinear terms, is carried out using linear approximations with no significant performance decay. Hence, simplicity and efficiency are the main features of the control design. The proposal is validated via realistic numerical simulations, Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Health-aware LPV model predictive control of wind turbines

  • Khoury, Boutrous
  • Nejjari Akhi-Elarab, Fatiha
  • Puig Cayuela, Vicenç
Wind turbine components are subject to considerable stress and fatigue due to extreme environmental conditions to which they are exposed to, especially when located offshore. Interest in the integration of control with system health monitoring has increased in recent years. The integration of a health management module with model predictive control (MPC) provides the wind turbine a mechanism to operate safely and optimize the trade-off between components’ life and energy production. In this paper, a health-aware LPV model predictive control approach for wind turbines is proposed. The proposed controller establishes a trade-off between the economic objective based on maximizing the energy production but at the same time taking into account the minimization of accumulated stress on the wind turbine blades. The controller uses an LPV model for dealing with the non-linearity of the wind turbine model and the inclusion of the stress model. The proposed approach is tested on a well-known wind turbine case., This work has been funded by the Spanish State Research Agency (AEI) and the European Regional Development Fund (ERFD) through the project SCAV (ref. MINECO DPI2017-88403- R) and by the DGR of Generalitat de Catalunya (SAC group ref. 2017/SGR/482)., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Reconfigurability analysis of multirotor UAVs under actuator faults

  • Sanjuan Gómez, Adrián
  • Nejjari Akhi-Elarab, Fatiha
  • Sarrate Estruch, Ramon
This paper presents a reconfigurability analysis for different multirotor structures. The aim is to determine whether the multirotor is able to continue the mission without losing its controllability when faults occur in its actuators. The classical controllability condition is not enough in these systems. Hence two complementary methodologies have been developed to analyse the controllability of the multirotors: Analysis of the Static Reconfiguration Module (ASRM) and Attainable Control Set (ACS)., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Design of shifting state-feedback controllers for LPV systems subject to time-varying saturations via parameter-dependent Lyapunov functions

  • Ruiz Royo, Adrián
  • Rotondo, Damiano
  • Morcego Seix, Bernardo
This paper considers the problem of designing a shifting state-feedback controller via quadratic parameter-dependent Lyapunov functions (QPDLFs) for systems subject to symmetric time-varying saturations. By means of the linear parameter varying (LPV) framework and the use of the shifting paradigm and the ellipsoidal invariant theory, it is shown that the solution to this problem can be expressed with linear matrix inequalities (LMIs) which can efficiently be solved via available solvers. Specifically, three hyper-ellipsoidal regions are defined in the state-space domain for ensuring that the control action remains in the linearity region of the actuators where saturation does not occur. Furthermore, the closed-loop convergence speed is regulated online according to the instantaneous saturation limit values through the shifting paradigm concept. The main characteristics of the proposed approach are validated by means of two illustrative examples., This work has been partially funded by the Spanish State Research Agency (AEI) and the European Regional Development Fund (ERFD) through the project SaCoAV (ref. PID2020-114244RB-I00). This work has also been partially funded by AGAUR of Generalitat de Catalunya, Spain through the Advanced Control Systems (SAC) group grant (2017 SGR 482) and by the University of Stavanger, Norway through the project IN-12267. A. Ruiz is also supported by the Secretaria d’Universitats i Recerca de la Generalitat de Catalunya, Spain, the European Social Fund (ESF) and AGAUR under a FI SDUR grant (ref. 2020 FI-SDUR 00097)., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Model-based prognosis approach using a zonotopic Kalman filter with application to a wind turbine

  • Khoury, Boutrous
  • Puig Cayuela, Vicenç
  • Nejjari Akhi-Elarab, Fatiha
Khoury Boutros et al. This is an open-access article distributed under the terms of the Creative Commons Attribution 3.0 United States License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original author and source are credited., Wind turbines generally operate under adverse conditions making them prone to relatively high failure rates. Due to the direct exposure of the blades to dynamic and cyclic loads of wind, the rotor and the blades unsurprisingly represent the most common major component damages of a wind turbine system, which is especially enhanced when located offshore. This paper presents a new model-based prognosis procedure based on a zonotopic Kalman filter (ZKF), which combines a physical model with observed data to assess the system degradation. Using this information and the model of the system, the end of life (EOL) and the remaining useful life (RUL) with its uncertainty can be predicted. The proposed prognostic method is applied to monitor the state of health of a wind turbine system specifically, its blades. The remaining useful life prediction will help in scheduling optimal maintenance and reducing the cost caused by wind turbine damage and unplanned shutdown., This work has been funded by the Spanish State Research Agency (AEI) and the European Regional Development Fund (ERFD) through the project SCAV (ref. MINECO DPI2017- 88403-R), by the DGR of Generalitat de Catalunya (SAC group ref. 2017/SGR/482) and by SMART Project (ref. num. EFA153/16 Interreg Cooperation Program POCTEFA 2014- 2020)., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Herramientas para la docencia de control digital en grados de ingeniería, Tools for teaching digital control in engineering degrees

  • Lerma Macaya, Eneko
  • Costa Castelló, Ramon
  • Griñó Cubero, Robert
  • Sanchis, Carlos
En este trabajo se describen un conjunto de materiales pedagógicos que han sido desarrollados para dar soporte a la docencia del control digital. En particular, se presentan un conjunto de herramientas interactivas y el proyecto Duino-Based Learning (DBL) pensado para desarrollar prácticas experimentales de control digital utilizando Arduino. Además, se describe el contenido de un curso de control digital, que  se imparte en el marco de una titulación de ingeniería industrial, y como se utilizan las diferentes herramientas desarrolladas en su docencia., Peer Reviewed, Postprint (published version)