Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 113
Encontrada(s) 2 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Proposal of a methodology for the development of final degree projects: a practical and systematic approach

  • Sanchis, R.|||0000-0002-5495-3339
  • Torre-Martínez, María Rocío de la|||0000-0002-8662-8901
  • Andres, B.|||0000-0002-7920-7711
  • Calleja, G.
[EN] Most undergraduate degree programmes have a subject called Final Degree Project (FDP) and it is usually the last academic requirement that students must complete in order to obtain their degree. The FDP is an opportunity for students to apply and demonstrate the knowledge and skills acquired during their study programme. It is important to note that the exact regulations and requirements for the FDP may differ among universities and countries. Some programmes may have alternative or equivalent options to the FDP, such as internships. The amount of European credit transfer and accumulation system (ECTS) associated with an FDP may vary depending on the university and the specific academic programme. In many cases, an FDP may represent a significant number of ECTS, often between 6 and 12 ECTS, although this may vary. It is therefore essential to check the specific regulations of the higher education institution and the study programme the student is enrolled in to understand the exact details of the FDP. However, what is common to all students who have to start their FDP is the uncertainty of how to approach its development. For this reason, the aim of this article is to propose a methodology for the development of an FDP that will help both students and lecturers, especially novel ones. The steps of the methodology include: (i) topic selection; (ii) literature review; (iii) definition of the problem or research questions; (iv) definition of objectives; (v) methodology; (vi) data collection; (vii) data analysis; (viii) interpretation of results; (ix) writing the document; (x) revision and correction; (xi) final submission and (xii) oral presentation. The proposed methodology, apart from being a guide to facilitate the FDP development process, it also contributes to the quality and validity of the work performed, provides clarity and focus, and facilitates time management., Universitat Politècnica de València, with the support of the Commission for the Evaluation and Monitoring of Innovation Projects (CESPIME) and the Institute of Education Sciences (ICE), has financed the Innovation and Educational Improvement Projects: PIME/22-23/358 Enchufes S.A.: Simulation of a plug manufacturing company in the area of business organisation; PIME/23-24/363 Active learning innovations in the context of business organisation (A-CEO); PIME/23-24/366 23-24 Activities to work on creativity, entrepreneurship and innovation in the classroom (ACEI). Moreover, this work was also This work was supported by the European Commission under the Erasmus+ Programme within the frame of CONTINUITY Project: Business Continuity Managers Training Platform with Reference No. 2021-1-IT01-KA220-VET-000033287
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Neurotechnological study on active learning based on group dynamics: application to human resources management.

  • MENGUAL RECUERDA, ANA|||0000-0003-4727-9099
  • Juárez Varón, David|||0000-0003-3251-8851
  • Torre-Martínez, María Rocío de la|||0000-0002-8662-8901
  • Andres, B.|||0000-0002-7920-7711
[EN] This work uses neurotechnologies applied to education to analyse the performance metrics of human resources management students during the realization of a group dynamic. To do this, neuroscience biometrics have been used to record brain metrics in a university academic experience in a degree in business administration and management. The biometrics used have been electroencephalography (EEG) for performance metrics, and galvanic skin response (GSR) for emotional arousal. The results allow quantifying the value of the brain performance variables, compared to the recording of the master class, being able to establish a comparison of methodologies for the face-to-face follow-up format. This work allows analysing the effects of an active learning method on the brain., This research is part of the action line "Call for Educational Innovation and Improvement Projects" at the Universitat Politècnica de València, under the educational innovation call "Learning + Teaching (L+T)," in the category "Educational Innovation and Improvement Project in Consolidated Teams," within the PIME/23-24/399 project "Neurotechnological study of active methodologies and monitoring formats for learning improvement".
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Analysis of brain performance metrics in active learning based on role-playing. A neurotechnological study

  • MENGUAL RECUERDA, ANA|||0000-0003-4727-9099
  • Juárez Varón, David|||0000-0003-3251-8851
  • Andres, B.|||0000-0002-7920-7711
  • Torre-Martínez, María Rocío de la|||0000-0002-8662-8901
[EN] This work aims to record and analyse, through the use of neurotechnology, in a face-to-face university training context, the effect on the learning process, using role-playing methodology in the subject of management and sales techniques. In this study, neurotechnologies have been used to measure cognitive processing in an academic experience of a university master's class in business administration. The neurotechnologies used have been the galvanic skin response (GSR) and electroencephalography (EEG). After analysing the brain records, based on attention, interest, stress and emotional connection (engagement), in a face-to-face educational context, the results allow quantifying the value of the key learning variables, compared to the recording of the master class, being able to establish the key moments of said methodology for the face-to-face follow-up format. The application of neuroscience technologies allows analysing the contributions of this active teaching methodology on the brain in the learning process., This research is part of the action line "Call for Educational Innovation and Improvement Projects" at the Universitat Politècnica de València, under the educational innovation call "Learning + Teaching (L+T)," in the category "Educational Innovation and Improvement Project in Consolidated Teams," within the PIME/23-24/399 project "Neurotechnological study of active methodologies and monitoring formats for learning improvement".
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Research data Set de datos (Dataset)

Experimental analysis of propeller thrust datasets

  • Gómez-Tejedor, José-Antonio|||0000-0001-6854-0829
  • Riera Guasp, Jaime|||0000-0002-4183-7195
  • Blasco-Pérez, Eduard
The data were used to analyze the thrust produced by a propeller, whose operating principles are based on the conservation of linear momentum. The study was carried out on an air track to avoid frictional forces. Several system characteristics were established, such as the angle of attack and different magnitudes were determined, including the dynamic thrust. 3D CAD software was used to design the propellers for the experiments. As propulsive systems are challenging for undergraduates to understand, it is essential to design experiments that can help their visualization and testing. The development of digital technology (high-speed cameras, digital tracking software, or 3D printers) facilitates the implementation of such designs., We would like to thank the Instituto de Ciencias de la Educación (ICE) in the Universitat Politècnica de València for their help, through the Innovation and Educational Quality Program and for supporting the team Innovación en Metodologías Activas para el Aprendizaje de la Física (e-MACAFI). This work has been supported by the UPV through the Project of Innovation and Educational Improvement Program (Projects PIME/18-19/76 and PIME/22-23/309 Convocatoria de Proyectos de Innovación y Convergencia de la UPV).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Active Learning Innovations in the Context of Business Organisation

  • MENGUAL RECUERDA, ANA|||0000-0003-4727-9099
  • Juárez Varón, David|||0000-0003-3251-8851
  • Andres, B.|||0000-0002-7920-7711
  • Torre-Martínez, María Rocío de la|||0000-0002-8662-8901
[EN] Active learning in the context of business organization consists of a series of educational innovations aimed at engaging students more effectively in their learning process. The main objectives are to actively involve students in their learning and provide them with practical and relevant experience in the field of business organization. To achieve these objectives, various pedagogical strategies and approaches are employed. A fundamental aspect is the use of case studies. These cases present relevant problems and challenges in the field of business organization, and students must analyse them, identify potential solutions, and make informed decisions. This enables them to develop critical thinking skills and acquire a deeper understanding of theoretical concepts through practical application. This article is the result of a project that focuses on creating a repository of case studies addressing relevant issues in the field of business organization. This repository serves as a resource for teachers and students, offering a wide range of cases that represent real and challenging situations in the business environment. The case studies can be used both in the classroom and individually, allowing students to learn autonomously and develop their analytical and decision-making skills., The Universitat Politècnica de València , with the support of the Comisión de Evaluación y Seguimiento de Proyectos de Innovación (CESPIME) and the Instituto de Ciencias de la Educación (ICE), has financed the following Proyectos de Innovación y Mejora Educativa: PIME/23-24/366 Activities to work on Creativity, Entrepreneurship and Innovation in the classroom (ACEI); PIME/22-23/358 Enchufes S.A.: simulation of a plug manufacturing company in the area of business organization; and PIME/23- 24/363 Active Learning Innovations in the Context of Business Organization (A-CEO). This work has also been supported by the European Commission under the Erasmus+ Programme within the frame of CONTINUITY Project: Business Continuity Managers Training Platform with Reference No. 2021-1- IT01-KA220-VET-000033287.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

E-tutoring in the post-COVID era

  • Sanchis, R.|||0000-0002-5495-3339
  • MENGUAL RECUERDA, ANA|||0000-0003-4727-9099
  • Andres, B.|||0000-0002-7920-7711
  • Calleja, Gema
[EN] The COVID-19 pandemic had a significant impact on all aspects of society, and one of the areas most notably affected was the education sector. This period of global crisis forced the education community to rethink and adapt rapidly to new approaches and paradigms, and technology became a key ally in this transformation process. There was a rapid adoption of online modalities, including e-tutoring. As educational institutions have returned to normality, it is evident that e-tutoring was not just a temporary solution but has become an integral part of the educational landscape, understood as the provision of tutoring services through online platforms. The aim of this article is to analyse in detail the implications and the continuing role of e-tutoring in higher education. To do so, a survey directed to both students and lectures was carried out at Escuela Politécnica Superior de Alcoy ¿ Universitat Politécnica de València (Spain). On one hand, participants were asked to provide insights into the advantages they perceived, such as the suitability of accessing tutoring services remotely, the flexibility to schedule sessions, and the accessibility. Additionally, the survey was focused on the participants' perception on the personalised nature of e-tutoring and the benefits of recording sessions. On the other hand, participants were also asked about drawbacks associated with e-tutoring. These weaknesses encompassed technological and connection limitations, the absence of face-to-face interaction, challenges in effective communication, difficulties in assessing student understanding, and concerns related to security and privacy, among others., Universitat Politècnica de València, with the support of the Commission for the Evaluation and Monitoring of Innovation Projects (CESPIME) and the Institute of Education Sciences (ICE), has financed the Innovation and Educational Improvement Projects: PIME/22-23/358 Enchufes S.A. Simulation of a plug manufacturing company in the area of business organisation; PIME/23-24/363 Active learning innovations in the context of business organisation (A-CEO); PIME/23-24/366 23-24 Activities to work on creativity, entrepreneurship and innovation in the classroom (ACEI). Moreover, this work was also This work was supported by the European Commission under the Erasmus+ Programme within the frame of CONTINUITY Project: Business Continuity Managers Training Platform with Reference No. 2021-1-IT01-KA220-VET-000033287.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Simulation to Facilitate the Acquisition of Knowledge: The Concept of Productivity

  • Andres, B.|||0000-0002-7920-7711
  • MENGUAL RECUERDA, ANA|||0000-0003-4727-9099
  • Torre-Martínez, María Rocío de la|||0000-0002-8662-8901
  • Sanchis, R.|||0000-0002-5495-3339
[EN] The aim of this paper is to share a recreational experience developed within the framework of the Industrial Management course of the Engineering Degrees at the Universitat Politècnica de València. This learning activity, called "Electroplane", aims to review and relate productivity concepts by using a simulation as active learning strategy., This work was supported by the Universitat Politècnica de València, with the support of the Commission for Evaluation and Monitoring of Innovation Projects (CESPIME) and the Institute of Education Sciences (ICE), and has financed the Educational Innovation and Improvement Project: PIME/22-23/358 Plug S.A.: Simulation of a plug manufacturing company in the industrial engineering area; PIME/23-24/363 Active Learning Innovations in the Context of Industrial Engineering (A-CEO); PIME/23-24/366 23-24 Activities to work on Creativity, Entrepreneurship and Innovation in the classroom (ACEI). Moreover, this work was supported by the European Commission under the Erasmus+ Programme within the frame of CONTINUITY Project: Business Continuity Managers Training Platform with Reference No. 2021-1- IT01-KA220-VET-000033287.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Innovative assessment based on multimedia proofs and social network sharing for introductory engineering courses

  • Correcher Salvador, Antonio|||0000-0002-2443-9857
  • Ricolfe Viala, Carlos|||0000-0002-2980-4569
  • Ivorra, Eugenio|||0000-0001-6062-2061
  • Cordero-París, Fernando Miguel
  • Blanes Campos, Carlos|||0000-0003-1977-7429
  • Martínez-Turégano, Jaime|||0000-0002-3483-8253
[EN] Training and education quality are crucial worldwide even more in the area of technical vocation. The assessment validates the performance of the training and education process, however, the design of assessments that validate the acquisition of certain knowledge, abilities or competences is still unsolved and remains open for research. In this paper, the advance in new technologies is used in the assessment process in a step ahead. Since social media is a big part of the daily life for lots of students, an assessment method is proposed that uses social media as the learning motivation. In consequence, the proposed assessment method is completely aligned with the student way of life and this fact motivates the student learning process since generating new high impact social media contents is a very challenging task. The paper shows the results of an assessment innovation project in which the authors develop a methodology for evaluating laboratory practices that measures knowledge of introductory concepts in automatic control engineering courses. The innovation aims to actively involve students in the generation of social media resources through modern technologies that are attractive to them. Under this methodology, students are tasked with creating a series of short videos explaining how to solve a specific problem or elucidate a concept covered in theory lessons. These videos are shared with their peers via a social network. Lecturers evaluate videos considering the quality in the explanation of technical concepts and impact in the social network. Results show that the proposed assessment methodology increases student motivation compared to the traditional assessment process and increases marks., The author(s) declare that financial support was received for the research, authorship, and/or publication of this article. This publication has been funded by Universitat Politecnica de Valencia through the program: "Convocatoria de Proyectos de Innovacion y Mejora Educativa. PROJECT Emergentes 2022." PROJECT-E-1854.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

The Role of Visual Collaboration Applications in Web Seminars for University Education

  • Andres, B.|||0000-0002-7920-7711
  • MENGUAL RECUERDA, ANA|||0000-0003-4727-9099
  • Juárez Varón, David|||0000-0003-3251-8851
  • Torre-Martínez, María Rocío de la|||0000-0002-8662-8901
[EN] Visual collaboration applications provide dynamic and interactive platforms that can significantly enhance the delivery and engagement of web seminars in university education. These tools support a wide range of academic activities by enabling collaborative brainstorming, project management, and efficient knowledge sharing through features such as automatic clustering, shape recognition, and template suggestions. Enhanced by artificial intelligence, these applications improve usability, streamline workflows, and foster a more engaging and productive learning environment. This paper proposes a set of alternative visual collaboration applications, offering a comprehensive comparison across various dimensions, including collaboration features, integrations, ease of use, and ideal use cases for university degree classes. It explores how these tools leverage AI to enhance their functionality, offering smarter automation, content suggestions, and real-time collaboration enhancements. By examining these applications, the paper highlights how they can be effectively integrated into university classrooms to promote active learning, support creative ideation, and simplify administrative tasks, ultimately improving the overall educational experience., Universitat Politècnica de València, with the support of the Commission for the Evaluation and Monitoring of Innovation Projects (CESPIME) and the Institute of Education Sciences (ICE), has financed the Innovation and Educational Improvement Projects: PIME/22-23/358 Enchufes S.A.: Simulation of a plug manufacturing company in the area of business organisation; PIME/23-24/363 Active learning innovations in the context of business organisation (A-CEO); PIME/23-24/366 23-24 Activities to work on creativity, entrepreneurship and innovation in the classroom (ACEI).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Capítulo o parte de un libro (BookPart)

Diagnóstico sobre la formación en ODS mediante encuestas al alumnado

  • M. Lorduy|||0000-0002-8942-8278
  • Marín-Morales, Javier|||0000-0003-1271-2892
  • Gallardo Bermell, Sergio|||0000-0002-3703-9983
[ES] El RD 822/2021 estipula que los planes de estudios deberán tener como referente los principios y valores democráticos y los Objetivos de Desarrollo Sostenible (ODS). Ello obliga a revisar y adaptar contenidos y actividades en las asignaturas de grado y posgrado. El primer paso en la adaptación de contenidos y actividades es determinar el grado de conocimiento y compromiso del alumnado respecto a los ODS. Existen numerosas herramientas para llevar a cabo este diagnóstico inicial, pero una de las más utilizadas por su capacidad para tratar un gran volumen de información es la encuesta. En este trabajo se presenta el diseño de la encuesta sobre formación en ODS que se ha realizado en las asignaturas “Estadística” (de primer curso) y “Tecnología Energética” (de cuarto curso) del Grado en Tecnologías Industriales de la Escuela Técnica Superior de Ingeniería Industrial de la Universitat Politècnica de València. Al tratarse de dos asignaturas cronológicamente muy separadas en el plan de estudios, se puede realizar un análisis cualitativo de la visión del estudiantado al iniciar y al terminar el grado. El trabajo resume los resultados obtenidos en las encuestas de ambas asignaturas y la comparación entre ellos., [EN] RD 822/2021 stipulates that the study plans must have as reference the democratic principles and the Sustainable Development Goals (SDG). This makes it necessary to review and adapt contents and activities in bachelor and master degree courses. The first step in the adaptation of contents and activities is to determine the degree of knowledge and awareness of the students regarding the SDGs. There are numerous tools to carry out this initial diagnosis, but one of the most widely used due to its ability to process a large volume of information is the survey. This paper presents the design of the survey on training in SDGs that was carried out in the subjects "Statistics" (first year) and "Energy Technology" (fourth year) of the Bachelor’s Degree in Industrial Engineering of the Escuela Técnica Superior de Ingeniería Industrial of the Universitat Politècnica de València. As these two subjects are chronologically far in the curriculum, a qualitative analysis of the student's vision can be carried out at the beginning and end of the bachelor’s degree. The work summarizes the results obtained in the surveys of both subjects and the comparison between them, Los autores agradecen el apoyo económico del Proyecto de Innovación y Mejora Educativa (PIME/22-23/341) "Coordinación entre asignaturas del Grado de Ingeniería en Tecnologías Industriales para potenciar la formación en Objetivos de Desarrollo Sostenible (ODS)" de la Universitat Politècnica de Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Evaluation of the Degree of Interdisciplinary Knowledge and Interest in Participating in Multidisciplinary Groups of the Degree in Industrial Engineering and Chemical Engineering Project Students and the Advanced GIS Students of the Degree in Geomatics Engineering and Surveying

  • LERMA ARCE, VICTORIA|||0000-0002-0433-7204
  • Coll-Aliaga, Eloína|||0000-0001-8938-9216
  • Pastor-Ferrando, Juan-Pascual|||0000-0001-7125-9464
  • Fuentes Bargues, José Luis|||0000-0003-4877-3291
  • Lo-Iacono-Ferreira, Vanesa G.|||0000-0002-1411-8785
  • Lorenzo-Sáez, Edgar|||0000-0003-3766-1198
[EN] The current socio-economic and professional context poses the challenge of training students in skills that will help them work cooperatively in multidisciplinary teams in the future. The chances of finding solutions to problems increase when team members know the potential that each can contribute. In this work, the student¿s perception of interdisciplinarity and their degree of interest has been evaluated to know the basis on which to apply teaching innovations that improve this perception between the degrees of Industrial Engineering and Chemical Engineering and the degree in Geomatic Engineering and Topography from the UPV. After designing and conducting a survey of students, it is concluded that there is a lack of knowledge about the possibilities and potential of interdisciplinary collaboration. However, students are interested in working in multidisciplinary teams, so they should try to incorporate this multidisciplinary. in teaching for the benefit of future graduates., This innovation has been realized thanks to PIME/22-23/354, ACDC-IT project n.1882.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Playmobil Pro System to Deal with Soft Skills in Industrial Engineering

  • Andres, B.|||0000-0002-7920-7711
  • Torre-Martínez, María Rocío de la|||0000-0002-8662-8901
  • MENGUAL RECUERDA, ANA|||0000-0003-4727-9099
  • Sempere-Ripoll, Francisca|||0000-0003-2658-6196
[EN] This paper explores the application of Playmobil Pro in negotiation with suppliers as an active learning methodology activity. This paper focuses on the effective communication soft skill, and it is applied in the Purchasing subject of the Master's Degree in Organizational and Logistics Engineering. To this extent, the authors propose the use of Playmobil Pro gamification tool to specifically deal with the supplier negotiation phase within the purchasing process. Playmobil Pro allows to work with metaphors to get to know the expectations of the participants. In this case study, Playmobil Pro will allow the students, that acquire the role of buyers, to deeply understand the behavior of the opposite negotiator, the supplier. The gamification workshop will enable to analyse the buyer and supplier behavior, and to extract conclusions to make decisions in the process of negotiation. Thus, the students will define negotiation strategies and how to approach them from the perspective of the purchasing company, taking as a starting point the knowledge of the of the supplier negotiation profile offered by the Playmobil- Pro methodology., This work was supported by the Universitat Politècnica de València, with the support of the Commission for Evaluation and Monitoring of Innovation Projects (CESPIME) and the Institute of Education Sciences (ICE), and has financed the Educational Innovation and Improvement Project: PIME/22-23/358 Plug S.A.: Simulation of a plug manufacturing company in the industrial engineering area; PIME/23-24/363 Active Learning Innovations in the Context of Industrial Engineering (A-CEO); PIME/23-24/366 23-24 Activities to work on Creativity, Entrepreneurship and Innovation in the classroom (ACEI). Moreover, this work was supported by the European Commission under the Erasmus+ Programme within the frame of CONTINUITY Project: Business Continuity Managers Training Platform with Reference No. 2021-1- IT01-KA220-VET-000033287.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

The Importance of the Role of the Internship Student in the Transfer of Knowledge of Open Data and Sustainable Development Goals at the Universitat Politècnica De València. Evidence from the Càtedra De Governança De La Ciutat De València

  • Coll-Aliaga, Eloína|||0000-0001-8938-9216
  • LERMA ARCE, VICTORIA|||0000-0002-0433-7204
  • Porres De La Haza, Maria Joaquina|||0000-0002-7913-4436
  • Lorenzo-Sáez, Edgar|||0000-0003-3766-1198
[EN] The achievement of the Sustainable Development Goals (SDGs) requires efforts and advances in all fields of science. However, it is ssential to have the greatest amount of data available without the need to generate new data with each step of the research. However, changing the paradigm from the value of data to the value of knowledge generated by data is not easy. That is why we must begin by promoting the benefits of a good open and reusable data policy at all levels among students and professionals in the sector. The innovation presented in this work is based on how a multidisciplinary environment can provide an important role to interns for the transfer of open data knowledge and Sustainable Development Goals at the Universitat Politècnica de València (UPV), Spain. To this end, evidence of the performance of students in internships within the Governance Chair of the City of Valencia is presented, where students have carried out mentored workshops, conferences, and seminars, where they have transferred knowledge and generated dissemination of the importance of open data. To other students, improving their transversal skills, especially teamwork and oral communication., This innovation has been realized thanks to PIME/22-23/354, PIME/21-22/268 and PIME/21-22/269.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Experiencia en la evaluación por pares aplicada a la asignatura Tecnología Energética

  • Gallardo Bermell, Sergio|||0000-0002-3703-9983
  • M. Lorduy|||0000-0002-8942-8278
  • Villanueva López, José Felipe|||0000-0002-7684-6884
  • Mayo, Patricia|||0000-0002-8403-5221
[EN] Introduction: In recent years, peer evaluation has acquired special relevance in university teaching since it entails involving students in the evaluation process. This methodology provides important benefits to the student. Methodology: The experience consists of the development and presentation, by teams, of an idea based on the application of renewable energy in the context of the subject ¿Energy Technology¿. At the end of the presentation, the rest of the classmates evaluate the idea by answering a series of questions on a five Likert scale. The evaluation carried out on each team is statistically analyzed to determine the degree of similarity with that carried out by the teacher. Results and discussion: The results show statistically significant differences in the evaluation of all questions, with a greater proportion observed in those referring to the presentation of the work. The final grade of the activity presents differences of less than one point for 93% of the teams. Conclusions: Knowing the discrepancies and having them limited, the teachers have the option of using peer evaluation as a resource in their subject., [ES] Introducción: En los últimos años, la evaluación por pares ha adquirido una especial relevancia en la docencia universitaria ya que implica involucrar al estudiantado en el proceso de evaluación. Esta metodología proporciona importantes beneficios al estudiante. Metodología: La experiencia consiste en la elaboración y presentación, por equipos, de una idea basada en la aplicación de una energía renovable en el contexto de la asignatura ¿Tecnología Energética¿. Al finalizar la presentación, el resto de los compañeros evalúa la idea respondiendo una serie de preguntas en escala cinco de Likert. Se analiza estadísticamente la evaluación realizada a cada equipo para determinar el grado de similitud con la realizada por el profesor. Resultados y discusión: Los resultados muestran diferencias estadísticamente significativas en la evaluación de todas las preguntas, observándose en mayor proporción en las referentes a la exposición del trabajo. La calificación final de la actividad presenta diferencias inferiores a un punto para el 93% de los equipos. Conclusiones: Conociendo las discrepancias y teniéndolas acotadas, los profesores tienen la opción de utilizar la evaluación por pares como recurso en su asignatura., Esta investigación se ha financiado por el Proyecto de Innovación y Mejora Educativa (PIME/22-23/341) de la Universitat Politècnica de València.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Social networking learning through enterprise social networks: a multi-criteria decision-making model

  • Leon, Ramona-Diana|||0000-0002-1448-0522
  • Rodríguez Rodríguez, Raúl|||0000-0001-5133-7023
  • Alfaro Saiz, Juan José|||0000-0003-2587-6853
[EN] This research proposes and tests a model to select the best enterprise social network for teaching. An emic approach is employed, and a Delphi study based on an analytic hierarchy process is developed. The results show that Viva Engage (R) is the most appropriate enterprise social network for teaching business administration subjects, and the most important factors that affect teachers' selection are related to teachers' profiles, students' profiles, and the platform's pedagogical features. This study extends the literature on educational technologies by presenting enterprise social networks as new learning management systems. Additionally, it provides a list of potential enterprise social networks together with a customising decision-making model. Starting from these, teachers can decide the best enterprise social network for teaching, given their objectives and preferences. Therefore, it helps teachers choose the best platform for their needs and make the transition from socio-constructivism learning to social network learning., This work was supported by Universitat Politecnica de Valencia [Grant Number PIME/22-23/344].
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Experimental analysis of propeller thrust in an undergraduate physics laboratory

  • Gómez-Tejedor, José-Antonio|||0000-0001-6854-0829
  • Riera Guasp, Jaime|||0000-0002-4183-7195
  • Blasco-Pérez, Eduard
[EN] As propulsive systems are challenging for undergraduates to understand, it is essential to design experiments that can help their visualization and testing. The development of digital technology (high-speed cameras, digital tracking software, or 3D printers) facilitates the implementation of such designs. We proposed to study the thrust produced by a propeller, whose operating principles are based on the conservation of linear momentum. The study was carried out on an air track to avoid frictional forces. Several system characteristics were established, such as the propellor's rotation speed and angle of attack and different magnitudes were determined, including the dynamic thrust and static force values. 3D CAD software was used to design the propellers for the experiments, and 3D printers to produce them., We would like to thank the Instituto de Ciencias de la Educación (ICE) in the Universitat Politècnica de València for their help, through the Innovation and Educational Quality Program and for supporting the team Innovación en Metodologías Activas para el Aprendizaje de la Física (e-MACAFI). This work has been supported by the UPV through the Project of Innovation and Educational Improvement Program (Projects PIME/18-19/76 and PIME/22-23/309 Convocatoria de Proyectos de Innovación y Convergencia de la UPV).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Analysis of the Combined Application of Group Dynamics in the Classroom for University Students

  • MENGUAL RECUERDA, ANA|||0000-0003-4727-9099
  • Andres, B.|||0000-0002-7920-7711
  • Torre-Martínez, María Rocío de la|||0000-0002-8662-8901
  • Juárez Varón, David|||0000-0003-3251-8851
[EN] Collaborative learning and group activities play a vital role not only in increasing academic knowledge but also in cultivating indispensable professional and social skills, such as teamwork, effective meetings, decision making, and empathy for problem solving, communication, motivation, leadership and conflict resolution. This article addresses how different group work techniques can be combined, such as Fishbowl, Role-playing and Brainstorming, in the same group learning dynamic, seeking motivation, involvement and emotional learning of students, in addition to preparing them for professional scenarios from the real world. The work was carried out with a total of 75 students, applying the aforementioned techniques and carrying out a subsequent quantitative investigation on 100% of the participants, to assess motivation and qualitative investigation to extract possible keys for improvement. The 90% of the participants positively assessed the activity, stating that they had learned a lot, found it highly enjoyable, and regarded it as highly useful and applicable in the professional world. Group dynamics allowed students to learn autonomously and develop their analytical and decision-making skills in a more efficient way. Furthermore, the combination of different group dynamics techniques at the same time, allows for more comprehensive and enriching experiences for students, especially in subjects with large groups. This enables students to participate by taking on different roles in each of the proposed dynamics simultaneously., The Universitat Politècnica de València , with the support of the Comisión de Evaluación y Seguimiento de Proyectos de Innovación (CESPIME) and the Instituto de Ciencias de la Educación (ICE), has financed the following Proyectos de Innovación y Mejora Educativa: PIME/23-24/366 Activities to work on Creativity, Entrepreneurship and Innovation in the classroom (ACEI); PIME/22-23/358 Enchufes S.A.: simulation of a plug manufacturing company in the area of business organization; and PIME/23- 24/363 Active Learning Innovations in the Context of Business Organization (A-CEO). This work has also been supported by the European Commission under the Erasmus+ Programme within the frame of CONTINUITY Project: Business Continuity Managers Training Platform with Reference No. 2021-1- IT01-KA220-VET-000033287.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Capítulo o parte de un libro (BookPart)

Inclusión de los ODS en las asignaturas de la materia Experimentación en Ingeniería Química en el Grado en Ingeniería Química

  • Lujan Facundo, Maria Jose|||0000-0001-6871-0584
  • Cuartas Uribe, Beatriz Elena|||0000-0003-2835-900X
  • García-Fayos, Beatriz|||0000-0002-7941-4243
  • Arnal Arnal, José Miguel
  • Iborra Clar, Alicia|||0000-0001-5937-8428
  • Sánchez-Arévalo, Carmen María|||0000-0001-6357-8107
  • Rodríguez López, Antonio Diego|||0000-0002-5741-8155
  • Ferrer-Polonio, Eva|||0000-0001-6412-3825
  • Zuriaga Agusti, Elena|||0000-0002-5383-1313
  • Ruvira-Quintana, Beatriz|||0000-0002-9108-1197
  • Martí Calatayud, Manuel César|||0000-0002-0745-1918
  • Mompó-Curell, Raúl|||0000-0002-7837-8025
  • Escrivá Cerdán, Clara
  • Garcia-Bernabe, Abel|||0000-0002-9740-0830
  • Cañada-Soriano, Mar|||0000-0002-9435-2132
  • Vilariño-Feltrer, Guillermo|||0000-0002-3063-3808
  • Carbonell Alcaina, Carlos|||0000-0002-0878-8977
  • Cardona, S. C.|||0000-0002-2882-3098
  • Fombuena, Vicent|||0000-0001-7266-6205
[ES] En la presente comunicación se presenta la estrategia seguida para dar visibilidad a los Objetivos de Desarrollo Sostenible (ODS) así como poder incluirlos en las asignaturas de la materia “Experimentación en Ingeniería Química” (EIQ) del Grado en Ingeniería Química (GIQ) de la UPV, tanto para el Grado impartido en la Escuela Técnica Superior de Ingeniería Industrial (ETSII) como para el impartido en la Escuela Politécnica Superior de Alcoy (EPSA). Esta materia incluye tres asignaturas experimentales que son continuativas (Experimentación en Ingeniería Química I, II y III). Durante el primer año (curso 22-23), se hará un diagnóstico del estado actual de conocimiento e implicación que tiene el alumnado sobre los ODS a través de encuestas de opinión con la herramienta Google Drive (una encuesta a principio de curso y otra a final de curso). Además, se planteará en cada asignatura una breve sesión formativa de los ODS. Durante el segundo año (curso 23-24), se decidirán qué ODS se van a trabajar en cada asignatura y se plantearán diferentes actividades en cada una de las asignaturas incluidas en la materia Experimentación en Ingeniería Química. De la misma forma, en esta segunda anualidad, se realizarán dos encuestas (una a principio y otra a final de curso) donde se evaluará el grado de aprendizaje, adquisición e implicación del alumnado sobre los ODS., [EN] This article presents the strategy followed to give visibility to the Sustainable Development Goals (SDG) as well as to be able to include them as a part of the content of the matter "Experimentación en Ingeniería Química" of the Degree in Chemical Engineering of the Universitat Politècnica de València (UPV), both for the Degree taught at the Escuela Técnica Superior de Ingenieros Industriales (ETSII) and for the one taught at the Escuela Politécnica Superior de Alcoy (EPSA). This matter includes three experimental subjects that are continuing (Experimentación en Ingeniería Química I, Experimentación en Ingeniería Química II and Experimentación en Ingeniería Química III). During the first year (academic year 22-23) a diagnosis will be made of the current state of knowledge and involvement that students have about the SDG through opinion surveys with Google Drive tool (a survey at the beginning and another one at the end of the course). In addition, a brief training session on the SDG will be proposed in each subject. During the second year (academic year 23-24) it will be decided which SDG are going to be worked on and different activities will be proposed in each of the subjects studied. In the same way, in this second year, two surveys will be carried out (one at the beginning and the other one at the end of the course) where the degree of learning, acquisition and involvement of the students on the SDG will be evaluated., Los autores de esta comunicación agradecen a la convocatoria de Proyectos de Innovación y Mejora Educativa de la UPV 2022 y al Proyecto Docente PIME/22-23/348 con título: ''Visibilización e inclusión de los ODS en las asignaturas de la materia Experimentación en Ingeniería Química en el Grado en Ingeniería Química'' a partir del cual se basa esta publicación.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

The Use of LinkedIn for University Education

  • Andres, B.|||0000-0002-7920-7711
  • MENGUAL RECUERDA, ANA|||0000-0003-4727-9099
  • Juárez Varón, David|||0000-0003-3251-8851
  • Torre-Martínez, María Rocío de la|||0000-0002-8662-8901
[EN] LinkedIn, traditionally recognized as a professional networking platform, offers potential for enhancing university education. By incorporating LinkedIn into academic practices, students can actively engage in creating and sharing content related to their lessons, fostering a culture of collaborative learning and professional growth. Students can generate posts summarizing their coursework, creating reviews of class materials. They can explore resources shared by industry professionals, gaining insights that extend beyond the classroom. Writing articles on LinkedIn allows students to delve deeper into topics of interest, improving their research and communication skills while building an online professional presence. Additionally, by posting about university seminars and discussions, students can connect with a broader audience, encouraging knowledge exchange and networking. This integration not only complements traditional learning methods but also prepares students for the professional world by enhancing their digital literacy, critical thinking, and ability to articulate ideas in a professional environment., Universitat Politècnica de València, with the support of the Commission for the Evaluation and Monitoring of Innovation Projects (CESPIME) and the Institute of Education Sciences (ICE), has financed the Innovation and Educational Improvement Projects: PIME/22-23/358 Enchufes S.A.: Simulation of a plug manufacturing company in the area of business organisation; PIME/23-24/363 Active learning innovations in the context of business organisation (A-CEO); PIME/23-24/366 23-24 Activities to work on creativity, entrepreneurship and innovation in the classroom (ACEI).
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Modelos colaborativos en obras publicas y su viabilidad jurídica en España con el marco normativo vigente

  • Gimeno Feliú, José María
En este trabajo se analiza la posibilidad de utilizar en España modelos colaborativos target costing en la construcción de infraestructuras complejas (o modelos concesionales) con la finalidad, desde la premisa de la sostenibilidad financiera, obtener un mejor resultado, preservando calidad en la ejecución, la transparencia y la necesaria seguridad jurídica. This paper analyzes the possibility of using collaborative target costing models in Spain in the construction of complex infrastructures (or concession models) with the aim, from the premise of financial sustainability, of obtaining a better result, preserving quality in the execution, transparency and the necessary legal security.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

La enseñanza del Derecho en el tardofranquismo

  • López Ramón, Fernando
Relato fundado en la experiencia personal del autor sobre la enseñanza recibida en la Facultad de Derecho de la Universidad de Zaragoza entre 1970 y 1975, poniendo de relieve las carencias del sistema y también algunos indicios de renovación. This report is based on the author’s personal experience of the teaching received at the Faculty of Law of the University of Zaragoza between 1970 and 1975, highlighting the shortcomings of the system and also some signs of renewal.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Las viviendas de uso turístico en el contexto internacional. Visiones regulatorias en las ciudades de San Francisco, Nueva York, Londres, Berlín y Ámsterdam

  • Guillén Navarro, Nicolás Alejandro
El fenómeno de las viviendas de uso turístico ha generado en los últimos años un abundante tratamiento doctrinal en España desde diversos puntos de vista. No obstante, se aprecia la inexistencia de estudios que analicen dicha problemática más allá de nuestras fronteras. En un momento en el cual el alquiler vacacional se ha conectado con el ámbito urbanístico y con su incidencia en el mercado del alquiler residencial, resulta interesante acudir al ámbito internacional para dar cuenta de cómo se han enfrentado diversas ciudades a estas problemáticas. Para ello, se analizarán algunos casos, en concreto, los de San Francisco, Nueva York, Londres, Berlín y Ámsterdam. The phenomenon of houses for tourist use has generated in recent years an abundant doctrinal treatment in Spain from various points of view. However, the lack of studies that analyse this problem beyond our borders is appreciated. At a time when vacation rentals have been connected to the urban sphere and with their impact on the residential rental market, it is interesting to go to the international arena to account for how various cities have faced these problems. To this end, various cases will be analysed, specifically those of San Francisco, New York, London, Berlin and Amsterdam.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

NH3 oxidation and NO reduction by NH3 in N2/Ar and CO2 atmospheres

  • Alzueta, María U.
  • Mercader, Víctor D.
  • Giménez-López, Jorge
  • Bilbao, Rafael
Impact of using CO2 or N2/Ar as bath gas, representative respectively of oxy-fuel or air combustion scenarios, has been evaluated on the oxidation of ammonia under a variety of operating conditions in a combined experimental and simulation study. Variables of relevance as temperature and oxygen stoichiometry have been considered at atmospheric pressure and under carefully controlled experimental conditions. Additionally, the impact of the presence of NO, which can be formed from ammonia oxidation, has also been evaluated. The experimental results obtained have been simulated with significant success with a detailed literature kinetic mechanism, which has been further used to interpret the main experimental observations. The results obtained are of interest in the power and energy industry, and can be used for guiding the co-firing of NH3 and carbon containing fuels.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

La protección de los excluidos por la digitalización financiera: de la voluntariedad a las obligaciones de servicio público

  • Esteban Ríos, Javier
La digitalización del sector financiero ha afectado negativamente a varios colectivos, que tienen dificultades para acceder a los servicios financieros digitales. Para garantizar la inclusión financiera de todos los ciudadanos pueden adoptarse diversas soluciones, justificadas por razones éticas, económicas o jurídicas, que pueden proceder tanto de los agentes del mercado como de las autoridades públicas. Entre estas últimos, como alternativa excepcional, algunos servicios financieros -considerados esenciales- podrían clasificarse como servicios de interés económico general, exigiendo su prestación presencial a través de obligaciones de servicio público. //// ABSTRACT: Various groups have been adversely affected by the digitalization of the financial sector, as they face difficulties in accessing digital financial services. Several solutions can be adopted to ensure the financial inclusion of all citizens, justified on ethical, economic or legal grounds, and which can come from both market operators and public authorities. Among the latter, as an exceptional alternative, certain financial services -considered essential- could be classified as services of general economic interest, requiring them to be provided in person by means of public service obligations.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Vine Shoots-Derived Hard Carbons as Anodes for Sodium-Ion Batteries: Role of Annealing Temperature in Regulating Their Structure and Morphology

  • Alvira, Darío
  • Antorán, Daniel
  • Vidal, Mariano
  • Sebastian, Victor
  • Manyà, Joan J.
Sodium‐ion batteries (SIBs) are considered one of the most promising large‐scale and low‐cost energy storage systems due to the abundance and low price of sodium. Herein, hard carbons from a sustainable biomass feedstock (vine shoots) were synthesized via a simple two‐step carbonization process at different highest temperatures to be used as anodes in SIBs. The hard carbon produced at 1200 °C delivered the highest reversible capacity (270 mAh g−1 at 0.03 A g−1, with an acceptable initial coulombic efficiency of 71 %) since a suitable balance between the pseudographitic domains growth and the retention of microporosity, defects, and functional groups was achieved. A prominent cycling stability with a capacity retention of 97 % over 315 cycles was also attained. Comprehensive characterization unraveled a three‐stage sodium storage mechanism based on adsorption, intercalation, and filling of pores. A remarkable specific capacity underestimation of up to 38 % was also found when a two‐electrode half‐cell configuration was employed to measure the rate performance. To avoid this systematic error caused by the counter/reference electrode polarization, we strongly recommend the use of a three‐electrode setup or a full‐cell configuration to correctly evaluate the anode response at moderate and high current rates.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Production of phenolic compounds from argan shell waste by reductive catalytic fractionation

  • Afailal, Zainab
  • Gil-Lalaguna, Noemí
  • Høj, Martin
  • Cornejo, Alfonso
  • Sánchez, José Luis
  • Jensen, Anker Degn
For efficient utilization of lignocellulosic biomass components, reductive catalytic fractionation appears as a promising biorefinery strategy. In this work, this concept of biomass valorization was used to study the potential of an unexplored feedstock, argan shells. This material was processed in a non-catalytic route and over a Pd/C catalyst in two different reaction media. The effects of the treatment temperature (250, 275, and 300 °C), as well as the catalyst loading (catalyst/argan shells mass ratio of 0.05 and 0.1 g/g), were also studied. The main product (lignin-derived oil) was thoroughly characterized using GC/MS/FID, SEC, and NMR. The highest monomer yields of 48–49 wt% based on the lignin content were obtained for n-butanol/water reaction medium at 300 °C using a Pd/C catalyst load of 0.1 g/g and for methanol reaction medium at 275 °C and 0.05 g/g. Significantly lower monomeric phenol yields were obtained in the non-catalytic route (4–19 wt% for n-butanol/water and 9–16 wt% for methanol). The main phenolic monomers in the catalytic pathway were 4-n-propanolguaiacol, 4-n-propanolsyringol, and 4-alkyl guaiacols and syringols, with some differences in the selectivities from one solvent to another.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Renewable hydrogen production by aqueous phase reforming of pure/refined crude glycerol over Ni/Al-Ca catalysts

  • Raso, Raquel
  • Abad, Eduardo
  • García, Lucía
  • Ruiz, Joaquín
  • Oliva, Miriam
  • Arauzo, Jesús
Renewable hydrogen production by aqueous phase reforming (APR) over Ni/Al-Ca catalysts was studied using pure or refined crude glycerol as feedstock. The APR was carried out in a fixed bed reactor at 238 °C, 37 absolute bar for 3 h, using a solution of 5 wt.% of glycerol, obtaining gas and liquid products. The catalysts were prepared by the co-precipitation method, calcined at different temperatures, and characterized before and after their use by several techniques (XRD, ICP-OES, H2-TPR, NH3-TPD, CO2-TPD, FESEM, and N2-physisorption). Increasing the calcination temperature and adding Ca decreased the surface area from 256 to 188 m2/g, and its value after the APR changed depending on the feedstock used. The properties of the acid and basic sites of the catalysts influenced the H2 yield also depending on the feed used. The Ni crystallite was between 6 and 20 nm. In general, the incorporation of Ca into Ni-based catalysts and the increase of the calcination temperature improved H2 production, obtaining 188 mg H2/mol C fed during the APR of refined crude glycerol over Ni/AlCa-675 catalyst, which was calcined at 675 °C. This is a promising result from the point of view of enhancing the economic viability of biodiesel.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Conversion of methylamine in a flow reactor and its interaction with NO

  • Marrodán, Lorena
  • Pérez, Teresa
  • Alzueta, María U.
The conversion of methylamine (CH3NH2, 1000 ppm) has been studied in an atmospheric-pressure flow reactor from both experimental and modeling points of view. Several values of the oxygen excess ratio (λ), from pyrolysis to fuel-lean conditions, have been tested, and a large number of different species have been quantified experimentally by three different diagnostic techniques: gas chromatography, Fourier Transform Infra-red spectroscopy (FTIR) and an infra-red NO analyzer. For the first time, the influence of NO addition (500 and 1000 ppm) on the stoichiometric oxidation of methylamine has also been experimentally evaluated, and the main products of such interaction have been identified. Results indicate that, unlike the little influence of oxygen availability on methylamine conversion, the presence of different concentrations of NO promotes methylamine oxidation at lower temperatures. A literature mechanism has been validated against the present experimental data since previous experimental works under these conditions are scarce. The largest discrepancies have been found for the formation of NH3 and NO as oxidation products, which are under and overestimated by the model, respectively, and under pyrolysis conditions, where modification of the kinetic parameters for the reaction CH2NH2 ⇌ CH2NH + H from the original mechanism notably improves the agreement between experimental and simulated results.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Flow Reactor Oxidation of Ammonia–Hydrogen Fuel Mixtures

  • Alzueta, Maria U.
  • Mercader, Victor
  • Cuoci, Alberto
  • Gersen, Sander
  • Hashemi, Hamid
  • Glarborg, Peter
Hydrogen-assisted oxidation of ammonia under flow reactor conditions was investigated through experiments and chemical kinetic modeling. Novel experiments, conducted in a tubular laminar flow reactor as a function of the NH3/H-2 ratio, stoichiometry, and temperature (725-1475 K), were analyzed along with literature results from tubular and jet-stirred flow reactors. Ignition and oxidation of NH3 is strongly promoted by the presence of H-2 under all conditions investigated. In general, the behavior is captured well by the kinetic model. With an increasing fraction of H-2 in the fuel mixture, the generation of chain carriers gradually shifts from being controlled by the amine reaction subset to being dominated by the oxidation chemistry of H-2, which is known more accurately. However, under reducing conditions, the H-2 consumption rate is strongly underpredicted. This shortcoming suggests that the thermochemistry of amine radicals and/or the formation of higher amines need further assessment. The present analysis shows that for lean oxidation of NH3/H-2 mixtures in tubular flow reactors, data obtained at higher temperatures, particularly for NO formation, may be strongly affected by the reaction during preheating or by mixing (dependent on reactor design) in the inlet section prior to the isothermal zone. Modeling predictions for the high pressure, medium-temperature ignition conditions in a large diesel engine indicate that NH3/H-2 fuel mixtures may still require a cofuel to secure stable ignition.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Experimental and Modeling High-Pressure Study of Ammonia–Methane Oxidation in a Flow Reactor

  • García-Ruiz, Pedro
  • Salas, Iris
  • Casanova, Eva
  • Bilbao, Rafael
  • Alzueta, María U.
The present work deals with an experimental and modeling analysis of the oxidation of ammonia–methane mixtures at high pressure (up to 40 bar) in the 550–1250 K temperature range using a quartz tubular reactor and argon as a diluent. The impact of temperature, pressure, oxygen stoichiometry, and CH4/NH3 ratio has been analyzed on the concentrations of NH3, NO2, N2O, NO, N2, HCN, CH4, CO, and CO2 obtained as main products of the ammonia–methane mixture oxidation. The main results obtained indicate that increasing either the pressure, CH4/NH3 ratio, or stoichiometry results in a shift of NH3 and CH4 conversion to lower temperatures. The effect of pressure is particularly significant in the low range of pressures studied. The main products of ammonia oxidation are N2, NO, and N2O while NO2 concentrations are below the detection limit for all of the conditions considered. The N2O formation is favored by increasing the CH4/NH3 ratio and stoichiometry. The experimental results are simulated and interpreted in terms of an updated detailed chemical kinetic mechanism, which, in general, is able to describe well the conversion of both NH3 and CH4 under almost all of the studied conditions. Nevertheless, some discrepancies are found between the experimental results and model calculations.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Highly selective catalytic hydrodeoxygenation of guaiacol to benzene in continuous operation mode

  • Gracia, J.
  • Ayala-Cortés, A.
  • Di Stasi, C.
  • Remón, J.
  • Torres, D.
  • Pinilla, J.L.
  • Suelves, I.
Benzene, mostly produced from fossil fuel sources, is an essential chemical to many modern industries. Alternatively to non-renewable methods currently used, the present work explores using fast pyrolysis biomass-derived bio-oils to furnish this valuable platform molecule. Notably, we report for the first time the impact of different operational parameters on the highly selective continuous catalytic hydrodeoxygenation of guaiacol, a bio-oil model compound, into benzene using a Mo2C/CNF-based catalyst. The parametric study includes a first evaluation of the effect of the hydrogen pressure (25, 50 and 75 bar), temperature (300, 325 and 350 °C) and weight hourly space velocity (4 and 10 gorg gcat−1 h−1) on the guaiacol conversion and product distribution, and a subsequent long-term evaluation (30 h on stream) of the catalyst under appropriate processing conditions The experimental results revelated that our Mo2C/CNF was able to achieve a conversion of 90–98% with a relative amount of benzene in the liquid product up to 81% for at least 30 h without any sign of deactivation at 75 bar of H2 and 350 °C, which is a landmark achievement in the conversion of bio-oil derived molecules into platform chemicals.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Production of derivatives from wheat straw as reinforcement material for paper produced from secondary fibers

  • Serrano, Iciar
  • Afailal, Zainab
  • Sánchez-Paniagua, Naiara
  • González, Pablo
  • Bautista, Ana
  • Gil-Lalaguna, Noemí
  • Gonzalo, Alberto
  • Arauzo, Jesús
  • Crespo, Cristina
  • Sánchez, Jose Luís
Nowadays, a high percentage (> 50%) of the paper produced in Europe uses recovered paper (secondary fibers) as raw material. In order to improve the mechanical properties of the paper produced, different kinds of additives are usually incorporated into the paper. Emerging renewable materials based on agricultural or forest residues, such as cellulose nanomaterials, have recently proved good capacities as reinforcing agents for different applications. In this work, pulp from wheat straw with a content of cellulose nanomaterial has been produced and tested as a mechanical reinforcing agent for paper production. A soda semi-chemical process was applied for the delignification of straw, to produce pulp with high cellulose content. Posteriorly, pulps with cellulose nanofibers were obtained in a high-pressure homogenizer, applying three different pretreatments to the cellulose pulp (acid hydrolysis, enzymatic hydrolysis and thermal treatment with glycerol) in order to facilitate the obtention of cellulose nanomaterial. Handsheets of paper were prepared from two sources of secondary fiber (fluting paper and old corrugated containers), adding different percentages of wheat straw derivatives (0, 3.5, 5 and 7%). The fibers' morphology and the papers' mechanical properties were investigated. Noticeable improvement rates (up to 25%) were observed for some mechanical properties of paper containing nanocellulose produced after the enzymatic and acid pretreatments. The quality of the secondary fibers source also affected the improvement rates achieved, with higher percentage changes for the lower-quality recycled paper.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Modeling TiO2/UV–vis bacterial inactivation: Useful tools for reactor optimization and design

  • Moreno, R.
  • Moles, Samuel
  • Ormad, Maria P.
  • Mosteo, R.
  • Monzón, A.
Heterogeneous photocatalysis applying TiO2 based catalysts has been widely studied for removing inorganic and organic compounds from water and for bacterial inactivation. This available and low-cost catalyst has demonstrated to be effective in the removal of organic pollutants and inactivation of pathogenic bacteria from water. The design of proper types of industrial-scale photoreactors has not been yet successfully implemented, probably due to the conceptual complexity of modeling this process in real wastewater. As a result, TiO2 based photocatalysis is still considered an effective but energetic-inefficient process. In this work, Escherichia coli (gram-positive) and Enterococcus sp (gram-negative) were selected for studying the kinetics of TiO2 photocatalysis. Since several approaches, such as fist-order kinetics, are not truly representative of the bacterial inactivation process, the experimental data were fitted to different mathematical models, such as Gompertz model, which has demonstrated to describe the process properly. Moreover, the effect of the main variables of the process in the inactivation kinetic constant of the Gompertz model has ben studied. More precisely, light intensity, water matrix, catalyst concentration and bacteria have been under study and their effect has been included in the kinetic equation. Finally, operational and construction parameters of a 20 m3/d annular photoreactor for bacterial inactivation has been successfully optimized applying the proposed kinetic model.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Conversion of NH3/CO/NO/CO2 mixtures

  • Alzueta, María U.
  • Salas, Iris
The present work addresses the impact of the presence of both CO and NO during the conversion of NH3 using CO2 or N2/Ar as bath gas, which would correspond to oxy-fuel or conventional air fuel combustion processes respectively. The variation of temperature and oxygen excess ratio is studied in a flow reactor setup at atmospheric pressure. Experimental results have been simulated with a literature detailed kinetic mechanism and the main observations have been discussed. The main results indicate that the effect of the presence of CO is less important than in other reactive systems. Conversion of NH3 is almost insensitive to the presence of CO, and the temperature regime for NH3 conversion is only significantly affected under fuel-lean conditions. The present results extend the experimental database on ammonia conversion, for different mixtures and conditions, and contribute to evaluate the possibilities of improving the ignition of this compound.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Jordan 3-graded Lie algebras with polynomial identities

  • Montaner, Fernando
  • Paniello, Irene
We study Jordan 3-graded Lie algebras satisfying 3-graded polynomial identities. Taking advantage of the Tits-Kantor-Koecher construction, we interpret the PI-condition in terms of their associated Jordan pairs, which allows us to formulate an analogue of Posner-Rowen Theorem for strongly prime PI Jordan 3-graded Lie algebras. Arbitrary PI Jordan 3-graded Lie algebras are also described by introducing the Kostrikin radical of the Lie algebras.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Enhancing waste hemp hurd-derived anodes for sodium-ion batteries through hydrochloric acid-mediated hydrothermal pretreatment

  • Antorán, Daniel
  • Alvira, Darío
  • Sebastián, Víctor
  • Manyà, Joan J.
Waste hemp hurd (WHH) was used as a sustainable feedstock for producing hard carbon-based anodes for sodium-ion batteries (SIBs). Two easily scalable production pathways were tested and compared: (1) pyrolysis (at 500 °C) and subsequent annealing at 800, 1000 or 1200 °C, and (2) hydrothermal pretreatment (at 180 °C) and subsequent annealing at the above-mentioned highest temperatures. Results indicated that when a HCl (2 mol m−3) aqueous solution was used as hydrothermal medium, the textural, structural and surface chemistry features linked to the electrochemical performance of the resulting hard carbons improved. The WHH-derived electrode produced via HCl-mediated hydrothermal pretreatment and subsequent annealing at 1000 °C showed an exceptional electrochemical performance in terms of specific capacity (535 mA h g−1 at 30 mA g−1) and rate capability (372, 156, 115, and 83 mA h g−1 at 0.1, 0.5, 1, and 2 A g−1, respectively) when an ester-based electrolyte was used (NaTFSI in EC/DMC). Using an ether-based electrolyte (NaPF6 in diglyme) improved both the ICE (from 69% to 78%) and cycling stability (85% of capacity retention after 300 cycles at 1 A g−1; 91% when current rate returned to 0.1 A g−1). In summary, relatively low-cost WHH-derived carbons are able to deliver an exceptional performance, much better than that reported so far for other biomass-derived carbons, and even close to that exhibited by more expensive and complex composite and hybrid materials.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Reseña (Review)

Recent advances in the preparation and application of biochar derived from lignocellulosic biomass: A mini review

  • Wang, Kanglei
  • Remón, Javier
  • Jiang, Zhicheng
  • Ding, Wei
With the rapid growth in the global population and the accelerating pace of urbanization, researching and developing novel strategies for biomass utilization is significant due to its potential for use in renewable energy, climate change mitigation, waste management, and sustainable agriculture. In this environmental context, this review discusses the recent advances in biomass conversion technologies for biochar production, including the first carbonization process and the subsequent activation methods of the biochar derived from lignocellulosic biomass (LBC). Parallel to this, this review deals with other essential parameters in biochar production, such as feedstock types, reaction environments, and operating conditions in the pyrolysis process, to determine the production and composition of LBC. Moreover, the wide-ranging applications of LBC in areas such as adsorption, catalysts, and energy storage are discussed, offering sustainable and environmentally friendly alternatives while reducing reliance on traditional energy sources and mineral resources, thereby providing practical solutions to environmental and energy challenges. Overall, this review not only provides a comprehensive comparative analysis of different LBC preparation methods, but also facilitates a deeper understanding of the advantages and limitations of these methodologies when it comes to developing high-value materials for sustainable applications.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

New insights into greener skin healthcare protection: Lignin nanoparticles as additives to develop natural-based sunscreens with high UV protection

  • Liang, Tianyu
  • Ma, Ya
  • Jiang, Zhicheng
  • Remón, Javier
  • Zhou, Yingdong
  • Shi, Bi
Despite lignin nanoparticles (LNPs) being extensively employed as assistant agents to improve the UV-blocking performance of sunscreens, there is a lack of information addressing how and to what extent the chemical and structural features of these particles relate to the improvements observed in the Sun Protection Factors (SPF) of the sunscreens. In this study, lignin oligomers were prepared by a solvothermal extraction process of five typical biomasses in a water–acetone co-solvent without noticeable degradation of the cellulose fraction. Afterward, LNPs were produced from the self-assembly of these lignin oligomers via the solvent-shifting methodology. When incorporated into the sunscreen, these had different morphologies, and exerted different UV-blocking capacities. The effects of the chemical structure and size distribution of the LNPs were systematically studied and compared to those of the original lignin oligomers. LNPs exhibited better UV-blocking ability than soluble lignin oligomers due to the more exposed chromophore on the surface. Besides, compact LNPs with conjugating Cdouble bondO and β-O-4 linkages, as well as the presence of the syringyl unit rich in the methoxyl group in the structures, were beneficial in boosting the UV resistance of the sunscreens. Even though smaller LNPs with higher surface area favored the UV shielding performance, LNPs with widely distributed sizes could further help decrease the UV transmittance. These findings provide an excellent basis for using lignin-derived materials as sunscreen additives and pave the way to developing new environmentally friendly materials for the cosmetic industry.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Manufacturing of isocyanate-based oligomeric dyes with high coloring capabilities: synthesis and application in the dyeing of organic chrome-free leather

  • Ding, Wei
  • Guo, Song
  • Liu, Haiteng
  • Pang, Xiaoyan
  • Ding, Zhiwen
  • Remón, Javier
Leather dyeing is a critical step in leather manufacturing, as it is responsible for providing leather products with an eye-catching visual aspect and adequate quality properties to meet customers' expectations. This step is becoming more and more challenging as the leather industry advances hand in hand with new environmentally friendly policies and regulations to achieve a safer and healthier planet by replacing the highly polluting Cr-based leather tanning technology with greener alternatives. As a result, achieving high-performance dyeing of organic chrome-free leather is one of the bottlenecks for the sustainable development of the leather industry. Herein, we propose a novel strategy to fabricate an isocyanate-based oligomeric dye (IBD) with high coloring capabilities (component content higher than 62.8%) based on toluene 2,4-diisocyanate and reactive red dye 180. This material has been tested for the dyeing of biomass-derived aldehyde (BDA)-tanned leather with excellent outcomes. The experimental results showed that the crust leather dyed with our novel IBD dyeing agent had higher color fastness and better fullness than the leather dyed with conventional anionic (CAD) or reactive red 180 (RRD-180) dyes. These excellent and promising results open new avenues in manufacturing high-performance organic Cr-free leather products and help to ensure the sustainable transition of the leather industry from Cr-based leather tanning to more sustainable alternatives, maintaining the final quality of the leather products.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

El dinero en efectivo en la encrucijada: impulso, restricciones y convivencia con el euro digital

  • Esteban Ríos, Javier
La progresiva digitalización de las relaciones sociales y económicas implica una tendencia a sustituir el efectivo por otros medios de pago de naturaleza digital. Pese a ello, el efectivo todavía es muy relevante para ciertos colectivos, cuenta con algunas características intrínsecas difícilmente replicables y se encuentra garantizado por el Derecho originario. En este contexto, los Estados miembros -y en particular España- han adoptado un enfoque bifronte en relación con el efectivo, de manera que, al mismo tiempo, promueven y restringen su uso por la ciudadanía. Ante esta dispersión en las respuestas nacionales, el legislador comunitario tramita una propuesta normativa, a fin de asegurar que el efectivo sigue siendo una alternativa de pago eficaz. Así, se pretende evitar la erosión del curso legal del efectivo, mediante una definición más precisa de su admisibilidad y a través de un impulso de su accesibilidad por la ciudadanía. Esta promoción del efectivo se inserta en un contexto europeo de transición, en el que también se enmarca la apuesta por el euro digital. Dicha moneda digital, en principio, complementará al efectivo, del que toma algunas de sus características básicas. Sin embargo, el lanzamiento del euro digital aparecería como un paso firme hacia la sustitución del efectivo, siendo la cohabitación entre ambos medios de pago coyuntural. The progressive digitisation of social and economic relations means that cash is tending to be replaced by other digital means of payment. Despite this, cash is still very relevant for certain groups, has some intrinsic characteristics that are difficult to replicate, and is guaranteed by primary law. In this context, Member States - and in particular Spain - have adopted a two-pronged approach to cash, both promoting and restricting its use by citizens. In response to this dispersion of national responses, the EU legislator is working on a regulatory proposal to ensure that cash remains an effective payment alternative. The aim is to prevent the erosion of the legal tender status of cash by defining its admissibility more precisely and by boosting its accessibility to the public. This promotion of cash is framed within a European context of transition, which also includes the commitment to the digital euro. This digital currency will, in principle, complement cash, from which it takes some of its basic characteristics. However, the launch of the digital euro appears as a firm step towards replacing cash, which means that the cohabitation of the two means of payment would be temporary.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

La mappatura emozionale del patrimonio di Bologna: un'azione educativa nella formazione degli insegnanti

  • García Ceballos, Silvia
  • Aso Morán, Borja
This proposal is based on the need to make future teachers more aware of the teaching of heritage from a relational approach based on the links and emotions woven with their territory, shaped by the richness of its places and traditions that bring people together and generate a common Bolognese identity. Heritage is particularly vulnerable to socio-cultural changes, to tourist overcrowding or to uncivic actions if we do not work on the value given to it by the people and their collective memory. Consequently, a specific transmission and training action is necessary to promote its valuation, care and, therefore, its survival and safeguarding. This proposal has been implemented in the Laurea Magistrale a Ciclo Unico in Scienze della formazione primaria of the University of Bologna and has resulted in a greater awareness among students of the important presence of heritage education in the classroom, as well as the knowledge of multiple educational possibilities for the use of the environment.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Synthesis of ketones from glycerol and 1,2-propanediol using copper and nickel catalysts: Unraveling the impact of reaction phase and active metal

  • Lete, Alejandro
  • Raso, Raquel
  • García, Lucía
  • Ruiz, Joaquín
  • Arauzo, Jesús
Catalysts based on nickel-aluminum and copper–aluminum were synthesized through the coprecipitation method with a Ni or Cu content of 28 mol%, expressed as Ni/(Ni + Al) or Cu/(Cu + Al). The catalysts were calcined at 675 °C and thoroughly analyzed using various characterization techniques (ICP-OES, N2 adsorption–desorption, NH3-TPD, CO2-TPD, XRD, H2-TPR and elemental analysis). The samples were tested in two different reaction systems, gas phase at atmospheric pressure and liquid phase at 34 absolute bar, to investigate the production of ketones from glycerol and 1,2-propanediol under reaction conditions of 227 °C and a mass of catalyst/reagent mass flow rate ratio (W/m) of 10 gCatalyst·min/gReagent. The characterization results revealed catalysts with high specific surface area and nickel and copper metallic particles, exhibiting good catalytic activity towards liquid products. Gas phase reactions favored the generation of acetol and carbon deposits, which were minimal in liquid phase reactions. The active metal played a crucial role, and it was demonstrated that copper, with a higher number of acidic sites, exhibited greater selectivity towards ketones than the nickel catalyst. The best performance was achieved by the CuAl catalyst in the gas phase reaction of glycerol, with a conversion of 67.0 ± 4.0 %, a carbon selectivity to acetol in the liquid products of 61.4 % and a yield to acetol of 119.8 mgAcetol/gGlycerol.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Coupling of neurons favors the bursting behavior and the predominance of the tripod gait

  • Serrano, S.
  • Barrio, R.
  • Lozano, Á.
  • Mayora-Cebollero, A.
  • Vigara, R.
In nature, it has been observed that the dominant locomotor pattern of hexapod insects is often the tripod gait. Our analysis of a Central Pattern Generator (CPG) of the insect movement gives reasons for this dominance: the mathematical CPG model presents the tripod pattern with bursting dynamics in a parametric region where an isolated neuron has a simpler behavior. That is, we show how the coupling of small networks of neurons makes the system to continue having bursting dynamics even when an isolated neuron would be spiking. Moreover, in parametric regions where a neuron shows chaotic dynamics, the CPG exhibits a chaotic synchronization phenomenon: the chaotic tripod gait. In other words, coupling loves bursting… and tripod gait. The hyperchaotic phenomenon is also present and we locate regions where up to four Lyapunov exponents are positive.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

An innovative ‘sea-thermal’ synergetic biorefinery for biofuel production: Co-valorization of lignocellulosic and algal biomasses using seawater under hydrothermal conditions

  • Zhou, Yingdong
  • Remón, Javier
  • Ding, Wei
  • Jiang, Zhicheng
  • Pinilla, José Luis
  • Hu, Changwei
  • Suelves, Isabel
This study explores the co-hydrothermal treatment (co-HTT) of almond hulls and Chlorella Vulgaris using seawater as an alternative HTT medium. The influence of the feedstock (individual biomass and all the possible binary mixtures) was systematically evaluated under different conditions (reaction temperatures and times). The feedstock mixture and hydrothermal conditions significantly influenced the overall product distribution: gas (1–5%), hydrochar (6–56%), biocrude (6–55%), and aqueous fraction (33–52%), along with the most representative physicochemical and fuel properties of these products. Notably, the biocrude had a calorific value of 24–31 MJ/kg, whereas the hydrochar shifted between 3 and 26 MJ/kg. The degradation of abundant polysaccharides in almond hulls produced acidic species, promoting the degradation of proteins to N-containing species in biocrude. The synergies between microalgae and almond hulls favored the deamination of amino acid and repolymerization of formed monomers. Process optimization revealed that the best biocrude production (59% yield and HHV = 28 MJ/kg) was obtained by treating C. Vulgaris at 268 °C for 180 min. Contrarily, the HTT of almond hulls under optimum processing conditions (300 °C and 112 min) also produced an energy-dense biocrude (29 MJ/kg) but with a much lesser yield (16%). However, such a low biocrude production can be synergistically increased up to 33 %, maintaining the HHV (31 MJ/kg), including up to 61 wt% of C.Vulgaris into the feedstock, with a feedstock energy recovery of 75%. Holistically, the co-HTT of 40 wt% C. Vulgaris and 60 wt% almond hulls at 300 °C for 180 min produced energy-dense liquid (23% yield and HHV = 32 MJ/kg) and solid (29% yield and HHV = 25 MJ/kg) biofuels simultaneously, with a feedstock energy recovery of 80%. Given these excellent prospects, this strategy provides timely and new insights into developing synergetic strategies to utilize microalgal and lignocellulosic biomasses more efficiently, paving the way toward developing holistic and unseasonal biorefinery processes.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Sustainable conversion of vine shoots and pig manure into high-performance anode materials for sodium-ion batteries

  • Alvira, Darío
  • Antorán, Daniel
  • Darjazi, Hamideh
  • Elia, Giuseppe Antonio
  • Sebastian, Victor
  • Manyà, Joan J.
Sodium-ion batteries (SIBs) are considered promising candidates for future grid energy storage, with hard carbons emerging as key commercial anode materials. This study presents a novel approach to synthesize N-doped hard carbons via co-hydrothermal treatment of vine shoots and pig manure and subsequent thermal annealing of the resulting hydrochar. This method enhances the development of micro- and ultra-microporosity in the synthesized hard carbons, with nitrogen, and to a lesser extent phosphorus and sulfur, introduced as doping elements. Furthermore, the incorporation of hydrochloric acid during the hydrothermal step promotes biomass hydrolysis, leading to increased mesoporosity and the formation of microsphere clusters. In the realm of electrochemical performance, an investigation into various ester- and ether-based electrolytes has revealed NaPF6 in diglyme as the best formulation, thanks to its thinner and more stable solid electrolyte interface (SEI). Using this electrolyte, the best-performing electrode showed an initial Coulombic efficiency (ICE) of 73 %, with reversible capacities of 239, 180, 86, and 57 mAh g−1 at 0.1, 1, 5, and 10 A g−1, respectively. In addition, the electrode exhibited a remarkable capacity retention of 88 % after 250 cycles as well as a compatible behavior when paired with a NVPF-based cathode.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

High-pressure study of the conversion of NH3/H2 mixtures in a flow reactor

  • García-Ruiz, Pedro
  • Castejón, Daniel
  • Abengochea, Miguel
  • Bilbao, Rafael
  • Alzueta, María U.
Carbon free fuels such as hydrogen (H2) and ammonia (NH3) will probably play a fundamental role owing to their potential for clean combustion without CO2 emissions. To contribute to the knowledge and development of technologies based on carbon free combustion, the present work deals with an experimental and kinetic analysis of ammonia oxidation in its mixtures with hydrogen at high pressure (up to 40 bar), in the 250–1250 K temperature range using a quartz tubular reactor and argon as bath gas. The impact of temperature, pressure, stoichiometry and H2/NH3 ratio on the concentrations of NH3, NO, NO2, N2O, and N2 obtained as main products of oxidation has been analyzed. The main results indicate that either increasing pressure, H2/NH3 ratio or oxygen availability results in a shift of NH3 and H2 conversion to lower temperatures. The NH3 and H2 consumptions are promoted by the reactions that produce NH2, H, OH, O, HO2 and HNO species and inhibited by reactions that form H2O, NH3, NO, H2NO and O2 species. The pressure effect is particularly significant in the low range of pressures studied. The main ammonia oxidation nitrogen products are N2 and N2O, while NO and NO2 concentrations are below the detection limit under all considered conditions. N2O formation is favored by increasing stoichiometry, pressure and H2/NH3 ratio. The experimental results are simulated and interpreted in terms of a literature detailed chemical kinetic mechanism, which, in general, is able to describe quite well both the H2 and NH3 conversion profiles under the studied conditions.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Influence of synthesis conditions on catalytic performance of Ni/CeO2 in aqueous-phase hydrogenolysis of glycerol without external hydrogen input

  • Jarauta-Córdoba, Clara
  • García, Lucía
  • Ruiz, Joaquín
  • Oliva, Miriam
  • Arauzo, Jesús
The aqueous-phase hydrogenolysis of glycerol was studied in Ni/CeO2 catalytic systems prepared by incipient wetness impregnation. The operating conditions were 34 bar, 227 ºC, 5 wt.% of glycerol, and a W/mglycerol = 20 g catalyst min/g glycerol without a hydrogen supply. The effect of the catalyst preparation conditions on the catalytic activity and physicochemical properties of the catalysts was assessed, particularly the calcination temperature of the support, the calcination temperature of the catalyst, and the Ni content. The physicochemical properties of the catalysts were determined by N2 adsorption, H2-TPR, NH3-TPD, and XRD, among other techniques. A relevant increase in acidity was observed when increasing the nickel content up to 20 wt.%. The increase in the calcination temperatures of the supports and catalysts showed a detrimental effect on the specific surface area and acid properties of the catalysts, which were crucial to the selectivity of the reaction. These catalysts notably enhanced the yield of liquid products, achieving global glycerol conversion values ranging from 17.1 to 29.0% and carbon yield to liquids ranging from 12.6 to 24.0%. Acetol and 1,2-propanediol were the most abundant products obtained in the liquid stream.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Oxidation of methylamine (CH3NH2)/CH4/NO mixtures in an atmospheric-pressure flow reactor

  • Alzueta, María U.
  • Pérez, Teresa
  • Marrodán, Lorena
The oxidation of methylamine (CH3NH2) and methane mixtures has been studied by experiments in a flow reactor at atmospheric pressure and temperatures of 350–1450 K. In addition to temperature, stoichiometry (ranging from fuel-rich to fuel-lean conditions) and the presence of NO have been evaluated. Several diagnostic techniques have been used to experimentally quantify many different species: gas chromatography, Fourier Transform Infra-red spectroscopy (FTIR) and an infra-red NO analyzer. Results show a negligible influence of stoichiometry both on the conversion of MEA and CH4 in the absence of NO, while the presence of NO acts to inhibit the conversion of CH4 with no appreciable influence on MEA conversion. This indicates the complex interaction occurring in the MEA/CH4/NO mixtures, for which the mechanism is not able to properly predict the conversion of CH4 in the presence of NO, while the rest of compounds are well reproduced both in the absence and presence of NO. This fact, together with the probable formation of species containing C and N, due to the presence of additional unidentified species and the deep analysis of the mass balances carried out, supports the idea of the formation of C-N species, not clearly identified so far. The literature mechanism used in simulations has provided good results in reproducing most of the species and conditions considered. The largest discrepancy has been observed for CH4 conversion in the presence of NO, supporting the existence of missing interactions in the mechanism.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Catalytic conversion of 1,2-propanediol to 2-propanone: an exploratory study

  • Lete, A.
  • García, L.
  • Ruiz, Joaquín
  • Arauzo, Jesús
Climate change underscores the urgency of exploring novel pathways for the decarbonization of the transportation sector. Within the aviation sector, biofuel appears to be the most viable short-term solution. Recently, the focus has centered on the aldol condensation of biomass-derived furans with ketones as 2-propanone (acetone) or 2-hydroxy-2-propanone (acetol), offering an efficient method to produce intermediates suitable for aviation fuels. However, 2-propanone is currently produced from cumene, a petroleum-derived source. This study proposes 1,2-propanediol (1,2-PDO), a sustainable product obtained by the hydrogenolysis of glycerol, a byproduct of the biodiesel industry, as a renewable feedstock for the generation of 2-propanone. For that purpose, the coprecipitation method with sodium hydroxide was employed to synthesize three copper, zinc, and aluminum-based catalysts. The catalysts were characterized through ICP-OES, N2 adsorption-desorption, XRD, and H2-TPR. The dehydration of 1,2-PDO to 2-propanone was investigated in a continuous system at 227 ºC, using a 10 wt% aqueous solution of 1,2-PDO at atmospheric pressure with a W/m ratio of 10 gCatalyst min g1,2-PDO-1. The catalyst with the lower zinc content achieved the highest carbon selectivity to 2-propanone at 22.1% and generated 1845 µmol2-propanone/mol1,2-PDO. This study revealed that lower zinc content could enhance 1,2-PDO dehydration to 2-propanone, preventing the subsequent hydrogenation of 2-propanone to 2-propanol. Additional optimization is required to attain higher yields.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Combustion of NH3/DME and NH3/DME/NO mixtures

  • Ruiz-Gutiérrez, A.
  • Rebollo, P.
  • Alzueta, M.U.
The objective of this work is to study the oxidation of ammonia and dimethyl ether mixtures (NH3/DME) both in the absence and the presence of monoxide of nitrogen (NO). For this purpose, laboratory experiments have been conducted in a quartz flow reactor setup in the 875–1425 K temperature range at atmospheric pressure, modifying the oxygen excess ratio (λ), and the NH3/DME mixture ratio with and without NO. The experimental results have been simulated with a literature-based kinetic mechanism. The results show that the presence of DME and an oxygen excess ratio affect the conversion of NH3, shifting its oxidation to lower temperatures, which decrease as the DME concentration in the mixture and λ increase. Interactions between ammonia and DME seem to be important under the studied conditions, presumably involving the formation and thermal decomposition of methyl nitrite (CH3ONO). These interactions affect the oxidation of ammonia at low temperatures, consume and produce NO, which would determine the final NO emission. When there is NO in the NH3/DME mixtures, NO is reduced up to 60 %, also favouring the oxidation of ammonia, but with an almost imperceptible effect of NO in the case of DME. The addition of different concentrations of DME also affects the oxidation behaviour of ammonia in NH3/DME/NO mixtures. In general, the conversion of both NH3 and DME is highly determined by the concentration of OH radicals, although thermal decomposition is also relevant for DME.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

La coordinación como técnica para exigir la participación provincial en un fondo autonómico de cooperación municipal (a propósito de la STC 124/2023, de 26 de septiembre)

  • Cofrades Aquilué, Lucía
Objetivos: sintetizar y examinar la STC 124/2023, de 26 de septiembre, sobre participación forzosa de las diputaciones valencianas en un fondo autonómico de cooperación municipal. Metodología: se ha empleado la metodología usual en las ciencias jurídicas para un estudio jurisprudencial; esto es, estudio de la resolución, de la normativa y de los estudios doctrinales relevantes sobre el tema en cuestión. Resultados: el Tribunal Constitucional ha validado la constitucionalidad de la declaración de interés general de la función de asistencia y cooperación de las diputaciones provinciales por parte de la Generalitat Valenciana, con el propósito de facilitar su participación económica obligatoria en la dotación del fondo de cooperación municipal. Se muestra la discrepancia de criterio de los magistrados del Tribunal, haciendo especial mención a los votos particulares emitidos. Conclusiones: la STC 124/2023 revela cómo la coordinación ha posibilitado un medio de interferencia sobre las diputaciones provinciales, planteándose ciertas dudas desde la perspectiva del respeto a la autonomía provincial. No se descarta la posibilidad de que en el futuro otras comunidades autónomas consideren oportuno realizar detracciones forzosas de fondos provinciales para destinarlos a los municipios situados en su ámbito territorial, limitando de esta manera la plena disponibilidad de sus ingresos.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Debilidades en la cohesión sanitaria. Un balance tras dos décadas de vigencia de la Ley de Cohesión y Calidad del Sistema Nacional de Salud

  • Pemán Gavín, Juan María
Objetivos: el trabajo lleva a cabo una aproximación global a la cohesión sanitaria en España tras dos décadas de vigencia de la Ley 16/2003. Metodología: se ha empleado la metodología habitual en las ciencias jurídicas; es decir, estudio de la legislación, de la doctrina y de la jurisprudencia. Resultados: en la primera parte del trabajo se identifican diversas señales de debilidad en el grado de cohesión efectiva del Sistema Nacional de Salud durante el período anterior a la crisis pandémica (2004-2019). En la segunda, se analiza la experiencia vivida en torno a la pandemia desde el punto de vista de la cohesión sanitaria. Conclusiones: se ha dejado pasar una circunstancia muy propicia para llevar a cabo rectificaciones de calado en la materia. Por eso, se formulan algunas propuestas para revertir la situación.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Polycyclic aromatic hydrocarbons formed during the pyrolysis of dimethoxymethane (DMM). Comparison with other oxygenated additives

  • Viteri, Fausto
  • Alexandrino, Katiuska
  • Millera, Ángela
  • Bilbao, Rafael
  • Alzueta, María U.
The influence of the temperature (1075 – 1475 K) and inlet concentration of fuel (33,333 and 50,000 ppmv) on the formation of the 16 EPA-priority Polycyclic Aromatic Hydrocarbons (PAH) from the pyrolysis of dimethoxymethane (DMM) was analyzed. PAH were detected in different phases (gas phase, adsorbed on soot, and stuck on the reactor walls) and quantified by gas chromatography-mass spectrometry (GC–MS). Additionally, the toxicity of the PAH samples, expressed as B[a]P-eq, was analyzed in all experiments. A comparison with the results obtained from the pyrolysis of other oxygenated compounds was also performed and similar behaviors were observed. The main results showed that, at low temperatures, the highest concentrations of PAH were found in the gas phase, while at high temperatures were found on soot. For both inlet concentrations of DMM, the light PAH, such as naphthalene and acenaphthylene, were found in major concentrations, in all phases and temperatures. The heavy PAH, such as fluoranthene and pyrene, increased its concentration on soot at highest temperatures. The highest formation of soot was obtained at 1475 K and follows the trend: 2,5DMF < tert-butanol < 2MF < 2butanol < iso-butanol < 1-butanol < ethanol < DMC < DMM. The highest formation of PAH was at 1275 K with the tendency: tert-butanol < 2-butanol < 1-butanol < 2,5DMF < 2MF < iso-butanol < ethanol < DMC < DMM. The highest B[a]P-eq value was found in the pyrolysis of 2,5DMF, and the lowest in the pyrolysis of DMM.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

High-pressure conversion of ammonia additivated with dimethyl ether in a flow reactor

  • García-Ruiz, Pedro
  • Ferrando, Pablo
  • Abián, María
  • Alzueta, María U.
The oxidation of ammonia (NH3) mixed with dimethyl ether (DME) was investigated from experimental and modeling points of view using a quartz flow reactor with argon as bath gas from 350 K to 1225 K, for two different DME/NH3 ratios (0.05 and 0.3), three oxygen excess ratios (λ = 0.7, 1 and 3) and various pressures (1, 10, 20 and 40 bar). The effect of pressure, oxygen stoichiometry, temperature, and DME/NH3 ratio has been analyzed on DME, NH3, NO, NO2, N2O, N2, O2, H2, HCN, CH4, CO, and CO2 concentrations. The present study indicates that oxygen availability, DME/NH3 ratio, and pressure are important variables that shift NH3 and DME conversion to lower temperatures as their values increase. Under certain conditions, the pressure effect can avoid NO and HCN production, which would represent a benefit for pressure applications. The main products of ammonia/dimethyl ether oxidation are N2, N2O, CO, and CO2, and under certain conditions, NO, H2, CH4, and HCN are also produced. NO2 is always detected below 5 ppm for all the conditions considered. The N2O formation is favored by increasing the O2 stoichiometry, pressure, and/or DME/NH3 ratio. The experimental results are interpreted and discussed in terms of an updated detailed chemical kinetic mechanism, which captures, with a general good agreement, the main trends of NH3 and DME conversion under the considered conditions. Despite this, some calculated species present discrepancies with the experimental results. The main challenge is the consideration of the C-N interactions that can be present in the combustion of DME/NH3 mixtures.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Déficits y excesos normativos en materia de transparencia, buena administración y buen gobierno: un análisis de la cuestión a partir de la legislación estatal y extremeña

  • Tahirí Moreno, Jesús A.
  • Cofrades Aquilué, Lucía
Objetivos: realizar una revisión crítica del estado de la cuestión en materia de transparencia, buena administración y buen gobierno con ocasión del décimo aniversario de la aprobación de la Ley 19/2013, de 9 de diciembre. Metodología: con la finalidad de construir un estudio sistemático y completo del tema tratado, la investigación se lleva a cabo mediante un análisis legal, doctrinal y jurisprudencial de los elementos que afectan a dos pilares clave de las políticas públicas de gobierno abierto: la transparencia y la colaboración (concepto este último que comprende la integridad y la rendición de cuentas o accountability). Además, se analiza el impacto del principio de buena administración en el procedimiento administrativo a la luz de la jurisprudencia más reciente. El método empleado es el comparativo, tomándose como muestra la normativa estatal y la extremeña. Resultados: la investigación constata diversos déficits y excesos que convendría tener presentes en futuras reformas legislativas, tanto a nivel estatal como autonómico. Conclusiones: se considera necesario realizar una modificación de la Ley 19/2013, de 9 de diciembre con la finalidad de integrar la jurisprudencia de la Sala Tercera y depurar defectos de técnica normativa. Asimismo, se concluye que sería adecuado regular un régimen de acceso especial a la información pública aplicable a aquellos sujetos que juegan un papel determinante en la formación de la opinión pública. A nivel autonómico, como conclusión principal, se recomienda llevar a cabo una refundición de la legislación en materia de transparencia y buen gobierno. Por lo que respecta a la buena administración, sería conveniente –siguiendo la CDFUE, la normativa autonómica y la jurisprudencia del Tribunal Supremo– que el legislador estatal reconociera expresamente el derecho a una buena administración. Finalmente, se critica la técnica empleada para regular los principios de buen gobierno y los códigos de conducta, así como la inexistencia de evaluaciones objetivas y obligatorias que permitan conocer su grado de cumplimiento.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Pure *-homomorphisms

  • Bosa, Joan
  • Vilalta, Eduard
We introduce and study the notion of pureness for *-homomorphisms and, more generally, for cpc order-zero maps. After providing various important examples of pureness, we show our main result: Any composition of two pure maps factors through a pure object up to Cuntz equivalence. This is used to obtain several factorization results at the level of C⁎-algebras.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

El limbo de la intermediación inmobiliaria en la legislación sobre vivienda

  • Moreu Carbonell, Elisa
Real estate brokerage in Spain has been a liberalised activity since the year 2000; anyone can work as a real estate broker without the need to accredit a minimum level of knowledge or be a member of a professional association. This study denounces the neglect of real estate brokerage in Spanish legislation and calls for a common regulation with the aim of controlling and limiting abuses. Although the new Housing Law of 2023 establishes some basic requirements for real estate agents and the information or advertising they offer, it has forgotten to regulate fundamental aspects of the profession that have been demanded by legal operators.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Natural-based UV-shielding additives to protect photosensitive pesticides: Production of nanoparticles from the co-self-assembly of lignin and tannin

  • Ya, Ma
  • Remón, Javier
  • Lingjuan, Luo
  • Wei, Ding
  • Zhicheng ,Jiang
  • Bi, Shi
This work explores the development of a renewable, carbon-neutral, light-colored UV-shielding film to protect photosensitive pesticides from solar radiation, as these chemicals are easily degraded under UV light, substantially reducing their efficiency and causing soil and water pollution. The abundant benzene rings in lignin and phenolic hydroxyls in tannin boosted the co-self-assembly of lignin and tannin into composite nanospheres by the simultaneous π-π stacking and H-bonding interactions between these two biopolymers. These lignin-tannin (LT) composite nanoparticles were used as natural UV-shielding additives to coat a poly-vinyl-alcohol (PVA) film, endowing the PVA-LT film with an excellent UV-shielding ability (>95 % efficiency) due to the strong π-π stacking and concentrated phenolic hydroxyls. Typical photosensitive pesticides covered with the PVA-LT film significantly increased their remaining rate by 1.5 times compared to those under the uncoated film. Besides, intensive intermolecular hydrogen bonds were generated between PVA and the abundant phenolic hydroxyl groups exposed on the hydrophilic shell of the LT coating, enhancing the mechanical properties and water vapor retention of the composite film. Our biodegradable composite film derived from natural plant extracts not only protected photosensitive pesticides from UV irradiation but also allowed the transmission of visible light to guarantee the photosynthesis process of crops.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Peripheral extracellular vesicles for diagnosis and prognosis of resectable lung cancer: the LUCEx study protocol

  • Rodríguez-Sanz, Jorge
  • Muñoz-González, Nadia
  • Cubero, José Pablo
  • Ordoñez, Pablo
  • Gil, Victoria
  • Langarita, Raquel
  • Ruiz, Myriam
  • Forner, Marta
  • Marín-Oto, Marta
  • Vera, Elisabet
  • Baptista, Pedro
  • Polverino, Francesca
  • Domingo, Juan Antonio
  • García-Tirado, Javier
  • Marin, José María
  • Sanz-Rubio, David
Background/Objectives: Lung cancer is the primary cause of cancer-related deaths. Most patients are typically diagnosed at advanced stages. Low-dose computed tomography (LDCT) has been proven to reduce lung cancer mortality, but screening programs using LDCT are associated with a high number of false positives and unnecessary thoracotomies. It is therefore imperative that a certain diagnosis is refined, especially in cases of solitary pulmonary nodules that are difficult to technically access for an accurate preoperative diagnosis. Extracellular vesicles (EVs) involved in intercellular communication may be an innovative biomarker for diagnosis and therapeutic strategies in lung cancer, regarding their ability to carry tumor-specific cargo. The aim of the LUCEx study is to determine if extracellular vesicle cargoes from both lung tissue and blood could provide complementary information to screen lung cancer patients and enable personalized follow-up after the surgery. Methods: The LUCEx study is a prospective study aiming to recruit 600 patients with lung cancer and 50 control subjects (false positives) undergoing surgery after diagnostic imaging for suspected pulmonary nodules using computed tomography (CT) scans. These patients will undergo curative surgery at the Department of Thoracic Surgery of the Miguel Servet Hospital in Zaragoza, Spain, and will be followed-up for at least 5 years. At baseline, samples from both tumor distal lung tissue and preoperative peripheral blood will be collected and processed to compare the quantity and content of EVs, particularly their micro-RNA (miRNA) cargo. At the third and fifth years of follow-up, CT scans, functional respiratory tests, and blood extractions will be performed. Discussion: Extracellular vesicles and their miRNA have emerged as promising tools for the diagnosis and prognosis of several diseases, including cancer. The LUCEx study, based on an observational clinical cohort, aims to understand the role of these vesicles and their translational potential as complementary tools for imaging diagnosis and prognosis.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Desafíos del modelo de empleo público tras la crisis sanitaria

  • Moreu Carbonell, Elisa
The Covid-19 health crisis has left public employment in a very delicate situation. The aim of my study is to diagnose the situation, four years after the pandemic, and to identify the best solutions for managing human resources in exceptional situations. When an exceptional environment arises in which agile and effective measures have to be taken, public administrations need to know what can be done to be able to continue functioning with a minimum impact on public services. La crisis sanitaria del Covid-19 ha dejado el empleo público en una situación muy delicada. Cuatro años después de la pandemia, el objetivo de mi estudio es hacer un diagnóstico de la situación y proponer las mejores soluciones para gestionar recursos humanos ante situaciones de excepción. Cuando irrumpe un entorno excepcional en el que hay que adoptar medidas ágiles y eficaces, es necesario que las Administraciones públicas sepan qué se puede hacer para seguir funcionando con un impacto mínimo en los servicios públicos y en la atención a la ciudadanía.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Envejecimiento activo, tecnología y salud: un desafío para las políticas públicas

  • Moreu Carbonell, Elisa
This paper addresses the connections between population ageing and the healthcare. The concept of ageing as a hindrance to social welfare has been overcome by the idea of active and healthy ageing. This idea, adapted to health, forces us to reconsider social and health policies, not only from a healthcare approach or from their economic sustainability. Technological advances and artificial intelligence (AI) systems mark the development of this global process. Este trabajo aborda las conexiones entre el envejecimiento de la población y el derecho a la salud. La concepción del envejecimiento como rémora para el bienestar social ha sido superada por la idea del envejecimiento activo y saludable. Esta idea adaptada a la salud nos obliga a replantear las políticas sociosanitarias, no solamente desde un enfoque nivel asistencial o desde su sostenibilidad económica. Los avances tecnológicos y los sistemas de inteligencia artificial (IA) marcan el desarrollo de este proceso global.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Conformational effects in the identification and quantification of ketohydroperoxides in the oxidation of <i>n</i>-pentane

  • Li, Dongyang
  • Li, Deshan
  • Herbinet, Olivier
  • Huang, Jiabin
  • Garcia, Gustavo A.
  • Arnoux, Philippe
  • Tran, Luc-Sy
  • Vanhove, Guillaume
  • Nahon, Laurent
  • Hochlaf, Majdi
  • Carstensen, Hans-Heinrich
  • Battin-Leclerc, Frédérique
  • Bloino, Julien
  • Zhang, Feng
  • Bourgalais, Jérémy
Stereochemistry plays a key role in both fundamental chemical processes and the dynamics of a large set of molecular systems of importance in chemistry, medicine and biology. Predicting the chemical transformations of organic precursors in such environments requires detailed kinetic models based on laboratory data. Reactive intermediates play a critical role in constraining the models but their identification and especially their quantification remain challenging. This work demonstrates, via the study of the gas-phase autoxidation of n-pentane, a typical fuel surrogate, that accounting for spatial orientation is essential for accurate characterization of such intermediates and for their further evolution. Using synchrotron-based photoelectron photoion coincidence spectroscopy and high-level quantum calculations to investigate the electronic structure and ionization dynamics of the main ketohydroperoxide isomer formed during the oxidation of n-pentane, we reveal the multiple thermally accessible conformers of the chain-branching agent, highlighting how their distinct ionization energies and fragmentation pathways can significantly affect intermediate quantification via photoionization-based probes, a universal in situ method of choice. This research underscores the importance of stereochemistry not only in combustion systems but in any chemical system where a molecular-level understanding is crucial for developing accurate predictive models for both scientific and industrial applications.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Synergistic production of nitrogen-rich hydrochar and solid biofuels via co-hydrothermal carbonization of microalgae and macroalgae: When nitrogen circularity matters

  • Zhou, Yingdong
  • Xiao, Haiting
  • Liu, Qing
  • Wang, Lan
  • Gong, Yuan
  • Remón, Javier
This work explores the synergies between N-rich (Chlorella pyrenoidosa) microalgae and N-deficient (Undaria pinnatifida) macroalgae for the production of N-containing hydrochar and solid biofuels via co-hydrothermal carbonization (co-HTC). The impact of the feedstock (each alga alone and all possible binary mixtures) was comprehensively assessed under different temperatures (180–260 °C) and times (60–240 min). The synergies between micro and macroalgae governed product distribution, nitrogen transformation pathways, and hydrochar quality, with these effects varying by processing conditions. Biomass synergies enhanced hydrochar quality at lower temperatures through deoxygenation reactions and/or liquid-phase repolymerization. In contrast, at higher temperatures, interactions between carbohydrates and proteins via solid-phase Maillard and Mannich reactions decreased hydrochar fuel quality but enriched nitrogen functionalities, such as pyridine-N. Optimization revealed that high N retention and hydrochar yield (up to 23%) were achieved by mixing up to 50 wt% macroalgae with microalgae at 223 °C for 174 min, maintaining functional N content (6 wt% N, 16% pyridine-N). Additionally, an energy-dense hydrochar (34% yield and 26 MJ/kg HHV) was synergistically produced by co-treating 70 wt% microalgae and 30 wt% macroalgae at 180 °C for 60 min. This synergistic algal approach highlights the potential of synergistic algal co-HTC to enhance nitrogen circularity, improve feedstock flexibility, and support sustainable biofuel and material production from marine resources.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Scalable synthesis of heteroatom-doped carbons from waste hemp hurd with enhanced sodium-ion and potassium-ion storage capabilities

  • Antorán, Daniel
  • Alvira, Darío
  • Sebastián, Víctor
  • Manyà, Joan J.
In this study, we applied an easily scalable two-step process comprising hydrothermal pretreatment with simultaneous mild heteroatom doping (N, N-S, and N-P) followed by carbonization at 800 °C to synthesize hard carbons (HCs) from waste hemp hurd for Na-ion and K-ion storage. The proposed synthesis pathway represents a viable alternative to the more energy-intensive, environmentally harmful, and/or challenging to scale up processes reported in the literature. The resulting carbons, particularly the dual NP-doped and single N-doped varieties, demonstrated improved electrochemical performance in terms of specific capacity (indicating more reversible ion storage sites) and rate capability (reflecting faster ion transport kinetics). These enhancements can be attributed to structural and surface chemistry modifications introduced during hydrothermal pretreatment. For Na-ion storage, the N-doped HC achieved a specific capacity of 293.6 mAh g−1 at 0.1 A g−1 (and 125 mAh g−1 at 1 A g−1) with an initial coulombic efficiency (ICE) of 73.5 % using an ester-based electrolyte. The same material showed an enhanced rate capability when an ether-based electrolyte was employed, achieving 155 mAh g−1 at 1 A g−1. For K-ion half-cells, the dual N-P-doped HC exhibited the best performance at low current rates, delivering a specific capacity of 260 mAh g−1 at 0.1 A g−1 in ester-based electrolytes. However, the N-doped HC showed the best rate capability at 2 A g−1 (57 mAh g−1), which is a reasonable value given the lack of mesopores in produced HCs.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

High performing and sustainable hard carbons for Na-ion batteries through acid-catalysed hydrothermal carbonisation of vine shoots

  • Alvira, Darío
  • Antorán, Daniel
  • Darjazi, Hamideh
  • Elia, Giuseppe Antonio
  • Gerbaldi, Claudio
  • Sebastian, Victor
  • Manyà, Joan J.
This study investigates the synthesis of hard carbons via acid-assisted hydrothermal carbonisation (HTC) of vine shoots, followed by thermal annealing, to be used as Na-ion battery anodes. Various carbons with diverse pore structures, ordering degrees, 2D morphologies, and chemical compositions are obtained using 2 mol dm-3 solutions of HNO3, HCl, H2SO4, or H3PO4 as the hydrothermal media. Compared to standard ester-based liquid electrolytes, the use of a diglyme-based electrolyte (NaPF6/DGM) substantially boosts both the initial coulombic efficiency (ICE) and the specific capacity, particularly evident with the highly ordered and porous H3PO4-1000 and HCl-1000 carbons. These materials exhibit outstanding performance, storing 200 mAh g-1 at 2 A g-1 and showing ICE values of 68% and 77%, respectively. The improved stability and capacity are attributed to the formation of a more stable and thinner solid electrolyte interface (SEI), along with sodium storage into graphitic regions through a solvent co-intercalation reaction. While ester-based electrolytes limit hard carbon mesoporosity and require the promotion of turbostratic domains, ether-based electrolytes enable the development of more ordered and porous carbons, enhancing transport kinetics, sodium storage capacity, and electrode stability. Overall, acid-catalysed HTC offers a sustainable pathway for tailoring hard carbon based electrodes, repurposing biomass residues into valuable materials for green and low-cost energy storage applications.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Full Lyapunov exponents spectrum with Deep Learning from single-variable time series

  • Mayora-Cebollero, Carmen
  • Mayora-Cebollero, Ana
  • Lozano, Álvaro
  • Barrio, Roberto
In this article we study if a Deep Learning technique can be used to obtain an approximate value of the Lyapunov exponents of a dynamical system. Moreover, we want to know if Machine Learning techniques are able, once trained, to provide the full Lyapunov exponents spectrum with just single-variable time series. We train a Convolutional Neural Network and use the resulting network to approximate the full spectrum using the time series of just one variable from the studied systems (Lorenz system and coupled Lorenz system). The results are quite surprising since all the values are well approximated with only partial data. This strategy allows to speed up the complete analysis of the systems and also to study the hyperchaotic dynamics in the coupled Lorenz system.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Use of methanol as a promoter for ammonia combustion

  • Ruiz-Gutiérrez, A.
  • Diego, I. de
  • Alzueta, M.U.
This work aims to study the oxidation of ammonia and methanol mixtures (NH3/CH3OH). For this purpose, laboratory experiments were conducted using a quartz flow reactor at atmospheric pressure, in a temperature range of 875–1425 K. The oxygen excess ratio (λ) and the NH3/CH3OH ratio were modified during the experiments. The experimental results have been simulated with a literature-based kinetic mechanism. The results show that the presence of CH3OH and the oxygen excess ratio affect the conversion of NH3, shifting its oxidation to lower temperatures as these variables increase. The oxidation of both fuels was slightly boosted with increasing CH3OH concentration. The λ study showed that the fuel-lean conditions accelerate NH3 oxidation at lower temperatures whereas do not have the same effect on CH3OH oxidation. The H radical concentration significantly influences fuel consumption, especially in reactions involving CH3OH and NH2, and it is also key for inhibition processes. CH3OH was found to initiate NH3 reactions, with strong competition for OH radicals between the two fuels. Nevertheless, methanol helps reduce ammonia's oxidation temperature. CH2OH was identified as the predominant species following H-abstraction from CH3OH. In the NH3/CH3OH ratio studies, increasing methanol concentration lowered the oxidation temperature of both fuels, with a temperature difference of up to 150 K observed for NH3/CH3OH ratios from 0.6 to 10. Increasing methanol concentration for a given NH3 value also shifted the prominence of secondary reaction pathways, further influencing the overall oxidation process.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Effect of calcination temperature and atmosphere on the properties and performance of CuAl catalysts for glycerol dehydration to acetol

  • Lete, Alejandro
  • Lacleta, Francisco
  • García, Lucía
  • Ruiz, Joaquín
  • Arauzo, Jesús
A series of CuAl catalysts were prepared by the coprecipitation method. The objective of this study was to investigate the influence of different calcination temperatures (500, 600, and 675 °C) and calcination atmospheres (N2 or air) on the catalysts physicochemical properties and performance in the gas-phase glycerol dehydration to acetol. The catalytic tests were carried out in a fixed bed reactor at 250 °C, atmospheric pressure, and a catalyst weight to glycerol flow rate ratio (W/m) of 30 gCatalyst min gGlycerol−1. The catalysts were characterized by ICP-OES, N2 adsorption-desorption, X-ray diffraction (XRD), H2 temperature programmed reduction (H2-TPR), temperature gravimetric analysis (TGA), and elemental analysis. The characterization results revealed that both calcination temperature and calcination atmosphere influenced the textural and metallic properties. Increasing the calcination temperature lowered the reduction temperature, and decreased the surface area. The calcination atmosphere influenced the surface area and pore diameter, and the N2 atmosphere generated a larger pore diameter. The best catalytic activity was achieved by the CuAl-675-N catalyst calcined at 675 °C in a N2 atmosphere, which produced a glycerol conversion of 99.0 % and an acetol yield of 67.3 %. The superior performance could be attributed to textural properties, the Cu phase, and minimized carbon deposition, establishing it as one efficient catalyst derived from inexpensive and widely available metals. This work proposes an economical and simple technique based on calcination to improve the catalytic activity of Cu-based catalysts.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Aqueous phase hydrogenolysis of glycerol with in-situ hydrogen generation over Ni catalysts supported on activated carbon: Effects of nickel loading and base addition

  • Raso, R.
  • García, L.
  • Ruiz, J.
  • Oliva, M.
  • Arauzo, J.
The present work studied the influences of nickel loading and KOH addition on the aqueous phase hydrogenolysis of glycerol over nickel supported on activated carbon (Ni/AC) catalysts prepared by the incipient wetness impregnation method and without external hydrogen addition in a continuous operation. It has been observed that the calcination stage of the catalytic precursor reduces nickel oxide to dispersed nickel metal crystallites, making catalyst activation with hydrogen unnecessary. This process predominantly yields liquid products, with low gas production under the studied conditions. Among the produced liquids, acetol and 1,2-propanediol are the major components. Furthermore, the addition of a base (KOH) is beneficial both in terms of significantly increasing glycerol conversion and the yield to liquids and also to improve selectivity towards 1,2-propanediol due to the participation of the basic route. The best catalytic activity was achieved using the catalyst with 10 wt% of Ni and added base with the highest glycerol conversion close to 40 % and selectivity to 1,2-propanediol greater than 70 %.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

The role of biogenic waste composition on pyrolysis: Part I – Char properties

  • Navarro, África
  • Fonts, Isabel
  • Ruiz, Joaquín
  • Ceamanos, Jesús
  • Gil-Lalaguna, Noemí
  • Murillo, María Benita
  • Gea, Gloria
The yield and properties of char derived from the co-digested manure and its main macro-components, including organic (cellulose, lignin, and protein) components and an inorganic component (CaCO3), produced at different pyrolysis temperatures (350, 550, and 750 °C) have been studied. Experimental results obtained from a surrogate co-digested manure were compared with the theoretically calculated values to explore potential interactions between these macro-components. The char properties analyzed included elemental analysis, pH, FTIR, XPS, and specific surface area. The effect of pyrolysis temperature on many properties was similar, regardless of the precursor (macro-component). Increasing pyrolysis temperature led to higher C content (>90 wt% for cellulose char at 750 °C), pH (from (∼7 for cellulose at 350 °C to ∼13 for co-digested manure), and specific surface area, observing a marked development of ultramicroporosity and microporosity, especially at the highest pyrolysis temperature studied, 750 °C. An exception was observed for the char derived from proteins due to melting during pyrolysis. By far, the solids from the pyrolysis of cellulose and lignin exhibited the most microporosity development (SSDR ≥ 650 m2 g-1), reaching, at the highest temperature studied, values close to those of physically activated carbons. Pyrolysis of the surrogate co-digested manure revealed the occurrence of Maillard reactions and also showed an interesting interaction involving CaCO3. The CaCO3 thermal decomposition is promoted when it is embedded into the organic matrix, where the CO2 generated during decomposition favored the Boudouard reaction of C from the organic components. This results in a lower biochar yield, 32 wt% versus 37 wt% (expected value), and a higher development of microporosity in the char.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

The role of biogenic waste composition on pyrolysis: Part II – Char CO2 adsorption capacity

  • Navarro, África
  • Fonts, Isabel
  • Ruiz, Joaquín
  • Ceamanos, Jesús
  • Gil-Lalaguna, Noemí
  • Ábrego, Javier
  • Gea, Gloria
The CO2 adsorption capacities (AC) of biochars obtained at 350, 550, and 750 °C from the main organic (cellulose, lignin, and protein) and inorganic (CaCO3) macro-components of biogenic waste, as well as from co-digested manure (CDM), have been determined for different CO2 concentrations (2–83 vol%) at 25 °C and atmospheric pressure. CO2 adsorption isotherms have been determined using two different experimental methodologies: thermogravimetric and fixed-bed dynamic adsorption tests, yielding similar results. The composition effect has been analyzed by comparing the adsorption performance of the chars derived from individual macro-components and the potential interactions occurring during their co-pyrolysis. Lignin and cellulose-derived chars showed higher CO2 retention (≈77 mg gbiochar−1) than those produced from protein (≈40 mg gbiochar−1). Pyrolyzed CaCO3 exhibited negligible CO2 adsorption. For surrogate_CDM chars, prepared at pyrolysis temperatures high enough to decompose CaCO3 in the organic matrix, experimental results showed a synergistic effect, with AC between 14 % and 47 % higher than theoretical predictions. This decomposition promoted the reverse Boudouard reaction and enhanced char microporosity. However, the improvement was insufficient to offset the dilution effect caused by the high CaCO3 content. AC results have been discussed based on the biochar textural and chemical properties, with ultramicroporosity being the key factor determining adsorption capacity. The AC of CDM-derived sorbents is similar to that of cellulose-derived, expressed per gram of waste (7–13 mg gwaste−1). Furthermore, the biochars retained at least 80 % of their initial AC after 3 adsorption-desorption cycles, indicating their potential for stable CO2 capture.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Influence of operating conditions on the kinetics of Iron-catalysed gasification of biocarbons with CO2

  • Chaos-Hernández, D.
  • Latorre, N.
  • Tarifa, P.
  • Romeo, E.
  • Monzón, A.
In this study, we investigated the catalytic gasification of cellulose-derived biocarbons (CDC) with CO₂ using Fe as the catalyst. Fe(%wt)/CDC samples were synthesized through controlled pyrolysis of cellulose impregnated with iron precursors and evaluated under varying reaction temperatures and CO₂ concentrations. Characterization by XRD, TGA, Raman, TEM, and N₂ adsorption revealed that the initial Fe loading in cellulose not only determines the final carbon content in each Fe(%wt)/CDC sample but also plays a crucial role in regulating the textural and structural properties of the resulting carbonaceous materials, as well as the Fe nanoparticle size distribution. Specifically, higher Fe loading led to a decrease in surface area, reduction of microporosity, an increase of pore diameter, and to larger average Fe nanoparticle sizes. During gasification, Fe nanoparticles were oxidized by CO₂, resulting in a decline in catalytic activity and ultimately limiting the complete gasification of the carbonaceous material by the end of the reaction. These opposing effects explain the varying behaviour observed in the Fe(%wt)/CDC samples studied. Analysis of the initial gasification rates indicated that both, the apparent reaction order with respect to CO₂ and the activation energy, increased with reaction temperature and CO₂ partial pressure (pCO₂), respectively. These results were successfully interpreted using a Langmuir-Hinshelwood model, which accounts for the influence of CO₂ adsorption on the observed reaction rate. These findings underscore the potential of Fe(%wt)/CDC materials for CO₂ utilization and biomass valorisation, providing valuable insights for the development of efficient catalytic gasification processes.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Environmentally-friendly tanning for leather production: a review

  • Ding, Wei
  • Remón, Javier
  • Jiang, Zhicheng
Traditional industrial methods of the leather industry produce toxic chromium-containing wastewater and solid wastes, calling for alternative procedures. Here, we review greener technologies to produce leather with focus on principles to design materials, high-efficiency chrome tanning, chrome-free processes, e.g., organic tanning, combination tanning, nanomaterial-based tanning, and tanning agent-free technology, as well as high-performance post-tanning using multifunctional polymers, integrated tanning-dyeing systems, and socioeconomical aspects. High-efficiency chrome tanning is done by high-exhaustion chrome tanning or inverse chrome tanning, which reduce the usage of chrome. Organic tanning employs biomass-derived and polymeric tanning agents.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Textile waste valorization via gasification: A comparative experimental study of different gasifying agents

  • Gracia-Monforte, C.
  • Zapata, G.
  • Afailal, Z.
  • Gea, G.
  • Arauzo, J.
This study explores the gasification of textile waste at 900 °C using different gasifying agents: air, CO2, and mixtures with steam. The research focuses on evaluating the composition and quality of the produced syngas, the characteristics of the generated tars, and the energy balance of the process for each gasifying agent. The results indicate that air is the most efficient gasifying agent from an energy perspective, yielding a well-balanced syngas composition. However, the introduction of steam alongside air enhances syngas quality by increasing the H2/CO ratio, making it more suitable for energy and chemical applications. This improvement comes at the expense of higher tar production, which may require additional treatment. Conversely, CO2 as a gasifying agent maximizes gas yield and cold gas efficiency, showing potential for improved process performance. Similar trends are observed when these results are compared with gasification studies of other waste materials, reinforcing the viability of textile waste as a feedstock for thermochemical conversion. These findings suggest that textile waste gasification could be a promising alternative for energy recovery, reducing environmental impact while contributing to circular economy strategies.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

An innovative ‘sorption-egg-hanced’ reforming approach to producing highly pure green hydrogen from biomass-derived aqueous effluents

  • Remón, Javier
  • Val-Planells, Edurne
  • Matharu, Avtar S.
  • García, Lucía
  • Arauzo, Jesús
The hydrothermal treatment of biomass forms large quantities of chemical-rich aqueous effluents. In the context of a zero-waste biorefinery, the latter represents a valuable resource for recovery and/or further functionalisation. This work reports for the first time the production of H2 with in-situ CO2 capture from the aqueous fraction of hydrothermally-processed almond hulls using a Ni-based catalyst coupled with a calcium-based sorbent derived from calcined eggshells. The effect of the reforming temperature and relative amounts of catalyst and sorbent (CaO) have been evaluated using a continuous reforming unit. The reaction temperature and the relative amount of catalyst directed the overall product distribution, with high temperatures favoured gas formation, and the catalyst allowed for lower temperatures to be used. Additionally, the temperature and the relative amount of sorbent significantly impacted the gas composition, with H2 enrichment as the latter (calcined eggshells) increased. Process optimisation revealed that a gas with a highly high H2 content (>95 vol%) can be obtained at 500 °C with relative amounts of catalyst and sorbent of 9 g catalyst min/g organics and 70 g CaO min/g organics, respectively. Such conditions allowed for capturing up to 90 % of the CO2, which resulted in a very high H2 production (0.12 g H2/g organics, i.e., the stoichiometric value). This represents a step ahead for developing greener processes and opens the door to exploring novel avenues for process intensification, avoiding further downstream processes to ensure holistic, zero-waste biorefineries.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Selective Conversion of Glycerol to Acetol: Effect of the Preparation Method of CuAl Catalysts and Reaction Phase

  • Maldonado-Martín, Francisco
  • García, Lucía
  • Ruiz, Joaquín
  • Oliva, Miriam
  • Arauzo, Jesús
A group of CuAl catalysts were synthesized with a Cu/Al molar ratio of 1:1 using different preparation methods: coprecipitation, surfactant assisted coprecipitation, polymeric precursor, and self-combustion and then screened for the selective dehydration of glycerol to acetol. The catalysts were employed in glycerol conversion at the same temperature (227 °C) in two different laboratory-scale systems, the first one at atmospheric pressure (gas phase) and the second one in a pressurized system at 34 absolute bar (liquid phase). The preparation method of the CuAl catalysts influenced the carbon yield to liquids and acetol selectivity. However, the reaction phase had a greater influence than the preparation method of the catalyst. In the gas phase, the carbon yield to liquids reached values above 40% and the carbon selectivity to acetol was higher than 90%. The highest acetol yield, 462.6 mgacetol/gglycerol, was obtained with the CuAl catalyst prepared by the surfactant-assisted coprecipitation method. This study provides a new perspective on catalyst design by highlighting the crucial role of preparation techniques in determining CuAl catalyst performance in the liquid and gas phases.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Fe-modified catalytic carbons for enhanced CO2 gasification: Influence of carbon source and operating conditions

  • Chaos-Hernández, D.
  • Latorre, N.
  • Tarifa, P.
  • Romeo, E.
  • Monzón, A.
In this study, we present results of characterization and reactivity of Fe-doped carbonaceous materials during their catalytic gasification with CO2. The samples include carbons derived from the thermal treatment of lignocellulosic residues pine sawdust (PiDC) and almond shells (AlDC) and a commercial graphite (AG) used for comparison. Iron-supported samples (Fe/PiDC, Fe/AlDC, Fe/AGC) were prepared by impregnating the raw materials (pine sawdust, almond shells and graphite) with a Fe precursor, followed by thermal decomposition under a reducing atmosphere. Characterization results revealed that Fe incorporation significantly influences the textural properties of the resulting carbonaceous materials. Specifically, Fe doping increased defect density and surface roughness while reducing microporosity, particularly in biomass derived carbons, as the Fe content increased. Dynamic gasification tests demonstrated that Fe enhances the reaction rate and lowers the onset temperature. Optimal gasification performance was achieved with intermediate Fe loadings maximizing catalytic efficiency while preventing rapid deactivation of Fe nanoparticles. Within the temperature range of 850–950 °C, nearly complete gasification was achieved, with residual content minimized to 10 % for Fe(4.2 %wt)/AGC, 16 % for Fe(2.4 %wt)/PiDC and 13 % for Fe(3.2 %wt)/AlDC. However, higher Fe loadings and temperatures exceeding 900 °C led to accelerated Fe deactivation due to sintering and oxidation. At CO2 concentrations below 8.3 %, these adverse effects were mitigated, optimizing the gasification rate. These findings underscore the critical interplay between Fe dispersion, carbon structure and gasification conditions, offering valuable insights for designing efficient Fe-based catalytic systems for CO2 valorization in sustainable energy applications.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Linking Exosomal MicroRNA Signatures in Sputum and Peripheral Blood to Inflammatory Endotypes in Severe Asthma

  • Sanz-Rubio, D.
  • Vera, E.
  • Rodríguez-Sanz, J.
  • Cubero, J.
  • Langarita, R.
  • Aguado, M.
  • Pastor, L.
  • Martín, L.
  • Marín-Oto, M.
  • Remacha, A. R.
  • Ruiz, M.
  • Gil, V.
  • Domingo, J. A.
  • Carretero, J. A.
  • Marín, J. M.
This study is the first to identify and validate distinct exosomal miRNA signatures in both plasma and induced sputum that differentiate T2-high and T2-low endotypes in severe asthma. By integrating miRNA expression with clinical parameters, we developed predictive models with high discriminatory power, highlighting the potential of these miRNAs as non-invasive biomarkers. These findings offer new insights into the molecular basis of asthma endotypes and support a precision medicine approach. In this revised version, guided by the reviewers’ comments, we have improved the clarity of our manuscript by including a new version of Figure 1 with adjusted graphs and greater consistency across panels. We have also added methodological clarifications to enhance the understanding of the experimental workflow, such as the selection criteria for the miRNAs included in the validation step. Additionally, we have completed the clinical data tables to reflect other relevant aspects, such as neutrophil counts and oral corticosteroid use. We are grateful for the opportunity to resubmit this work and for the reviewers’ efforts, which have helped us strengthen several aspects of our manuscript.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Recent advances in versatile cellulose-based 3D-printed drug delivery systems: A review

  • Wang, Kanglei
  • Wu, Yanbei
  • Remón, Javier
  • Ding, Wei
Advancing effective drug therapies is crucial for improving human health. However, traditional drug delivery systems (DDSs) struggle to customize formulations for individual patient needs, prompting exploring innovative solutions. The emergence of 3D printing (3DP) technology allows for designing customized DDSs. Cellulose and its derivatives can positively lower blood cholesterol and stabilize blood glucose levels due to their excellent biocompatibility and safety. These cellulose-based materials are supposed to fulfill the necessary criteria for biocompatibility, printability, and biomanufacturing in DDSs. Despite their excellent potential and promising features, constructing 3D-printed DDSs utilizing nanocellulose (NC) and cellulose derivatives remains largely unexamined. Given this, our review highlights the recent advances in cellulose-based inks for drug delivery, detailing the multifunctional roles of cellulose derivatives, such as adhesives, drug-loaded filaments, controlled-release materials, thickeners, and fillers. Their versatility impacts ink rheology, allowing for tailored mechanical properties and porous structures in DDSs, including tablets, capsules, dispersible films, or scaffolds. Furthermore, their in vitro and in vivo application performances have been rigorously evaluated. Overall, this review emphasizes for the first time the unique advantages and various applications of 3D-printed cellulose-based DDSs in personalized medicine, which is significant in providing guidance for developing safe biomedical materials, triggering the growth of personalized medicine.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Almost fine gradings on algebras and classification of gradings up to isomorphism

  • Elduque, Alberto
  • Kochetov, Mikhail
We consider the problem of classifying gradings by groups on a finite-dimensional algebra A (with any number of multilinear operations) over an algebraically closed field. We introduce a class of gradings, which we call almost fine, such that every G-grading on A is obtained from an almost fine grading on A in an essentially unique way, which is not the case with fine gradings. For abelian G, we give a method of obtaining all almost fine gradings if fine gradings are known. We apply these ideas to the case of semisimple Lie algebras in characteristic 0: to any abelian group grading with nonzero identity component, we attach a (possibly nonreduced) root system Φ and, in the simple case, construct an adapted Φ-grading.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

High-Pressure Oxidation of Ammonia Mixed with Dimethoxymethane

  • Alexandrino, Katiuska
  • Andrés, Álvaro
  • Callejas, Alicia
  • Alzueta, María U.
The oxidation of ammonia-dimethoxymethane (NH3-DMM) mixtures at high pressure was analyzed from both experimental and kinetic modeling points of view. Experiments were performed using a laboratory tubular flow reactor installation and were conducted at 10, 20, and 40 bar under fuel-rich (λ = 0.7), stoichiometric (λ = 1), and fuel-lean (λ = 3) conditions and temperatures ranging from 650 to 1250 K. The inlet DMM concentration was varied (100 and 200 ppm), keeping the concentration of ammonia constant at 1000 ppm. The data were interpreted in terms of a detailed chemical kinetic model. Despite some discrepancy between the model predictions and measurements, the model accurately followed the experimental trends, highlighting its ability to describe the oxidation of the NH3-DMM mixture. The experimental and predicted results suggested that the conversion of both ammonia and DMM was favored by increased pressure and higher inlet concentrations of O2 and DMM. Under the conditions of the present work, the dominant path for ammonia and DMM conversion leads to N2/N2O and CO/CO2 in any case. Concentrations of NO and NO2 were below the detection limit in all the experimental conditions studied, which imply a benefit in the reduction of NOx emissions during the combustion of pure ammonia. DMM enhanced the ammonia reactivity, although its presence leads to the formation of CO2 not only by the common CO + OH reaction but also through the interaction of N2O with CO.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Derecho y políticas ambientales en aragón (Primer semestre 2025)

Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

CCA-attacks on lattice-based encryption-decryption schemes

  • Hernández Costoya, Alba
  • Larraya Sancho, Alba
  • Marco Buzunáriz, Miguel Ángel
This paper presents two distinct chosen-ciphertext attacks (CCA) against lattice-based encryption and decryption schemes, in particular based on the LWE problem, a class of post-quantum cryptographic algorithms. First we attack fully homomorphic encryption-decryption schemes (FHE) exploiting the additional information that the small modulus reduction offers. We compare this attack with the CPAD attack presented in Checri (2024). Afterwards we present an attack against Kyber.CPAPKE, and another against a weakened version of Kyber.KEM where the cyphertext is not checked for correctness; and compare them to the previous Key Mismatch Attack in Qin (2021). Our work remarks the importance of protecting the decryption function in the different implementations of these cryptographic schemes, and the importance of CCA security in nowadays cryptosystems.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Flow Reactor Study of NH3/DEE Oxidation Chemistry

  • Ruiz-Gutiérrez, A.
  • Bello-Gallego, A.
  • Alzueta, M. U.
The pursuit of environmentally sustainable alternatives to conventional fuels is essential today. Ammonia emerges as a promising candidate, though its inherent disadvantages must be addressed. Co-firing ammonia with fuels exhibiting superior thermochemical properties is one of the most widely accepted solutions. The present study investigates the oxidation of ammonia and diethyl ether mixtures (NH3/DEE). To this end, a quartz flow reactor was employed at atmospheric pressure, within a temperature range of 875–1425 K. The oxygen excess ratio (λ) and the NH3/DEE mixture ratio were systematically varied during the experiments. The results show an increase in the reactivity of ammonia when mixed with DEE. During pyrolysis, DEE is inhibited by competition for H radicals, which are essential for initial conversion steps. DEE undergoes thermal decomposition without a significant radical pool, while NH3 reactivity remains low. With the increase of the oxygen excess ratio, fuel oxidation occurs at lower temperatures. Hydroxyl (OH) and atomic oxygen (O) radicals are crucial in NH3 oxidation, while the presence of DEE derivatives further promote this oxidation, although both fuels exhibit competitive behavior regarding radical consumption. Variations in λ do not cause a significant effect in the oxidation temperature of DEE, with OH radicals playing a central role in the minor differences observed. Hydrogen abstraction via interaction with H radicals is the most important consumption reaction of DEE, mainly occurring at the secondary carbon position. Conversely, the production and interaction of derivatives at other positions contribute to the most inhibitory reactions in DEE oxidation. The NH3/DEE ratio has a significant impact on ammonia oxidation, particularly under high DEE dilution conditions (NH3/DEE = 10). OH and H radicals drive oxidation, while an increased DEE concentration leads to CH3 radical formation, enhancing fuel consumption. A literature-based kinetic mechanism, modified in the present work, was employed to represent and interpret the current results accurately.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Valorization of pure and biodiesel-derived refined crude glycerol to renewable acetol over copper-based catalyst: Effect of operating conditions and catalyst stability

  • Lete, Alejandro
  • García, Lucía
  • Ruiz, Joaquín
  • Arauzo, Jesús
Acetol is a key intermediate in the aldol condensation of biomass-derived furans, enabling the production of carbon chains within the aviation fuel range. This work proposes glycerol, a biomass-derived by-product from biodiesel production, as a renewable feedstock for acetol production. The catalytic performance of a CuAl catalyst was evaluated in the gas phase dehydration of glycerol, focusing on the influence of temperature (200–300 °C), catalyst weight to glycerol mass flow ratio (10–50 gCatalyst min gGlycerol−1), and carrier gas to liquid ratio (200–600 m3GasSTP m3Liquid−1). Both pure and biodiesel-derived refined crude glycerol were used as feedstock. Long-term stability experiments assessed the evolution of catalytic activity and physicochemical properties over time. A great activity was obtained under conditions of 250 °C, 30 gCatalyst min gGlycerol−1, and 400 m3GasSTP m3Liquid−1 with pure glycerol after a time-on-stream (TOS) of 2 h (95.1 % glycerol conversion and 564 mgAcetol gGlycerol−1). Stability studies provided good catalytic results after a TOS of 52 h using pure glycerol (72 % glycerol conversion and 266 mgAcetol gGlycerol−1) and demonstrated that coke deposition was responsible for catalyst deactivation. The use of refined crude glycerol proved to be highly effective in the first hours of the reaction (98.7 % glycerol conversion and 570 mgAcetol gGlycerol−1 for a TOS of 2 h), however, rapid deactivation was observed due to solids deposition. This catalytic route highlights the feasibility of valorization of biomass residues for producing renewable acetol, a promising precursor for sustainable aviation fuel (SAF).
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Pyrolysis of ethylene – ammonia mixture: Formation of soot, gases and PAH

  • Viteri, Fausto
  • Soler, María
  • Starace, Paola
  • Abián, María
  • Alzueta, María U.
The effect of inlet concentration of NH3 (0, 30000, 60000, and 100000 ppm) and temperature (1275, 1375, and 1475 K) on the formation of soot, gases and polycyclic aromatic hydrocarbons (PAH) from the pyrolysis of C2H4/NH3 mixtures with constant concentration of C2H4 (30000 ppm) was analyzed. Light gases were quantified through gas chromatography, while soot was collected in a fiber filter, at the reactor outlet, and the particle diameter was analyzed. The PAH were analyzed through gas chromatograph coupled to mass spectrometer by considering the 16 PAH reported by Environmental Protection Agency (EPA) as priority pollutants. The main results show that the higher the presence of NH3 in the NH3/C2H4 mixture, the lower the soot formation. This decrease of soot is accompanied by an increase of HCN and a decrease in C2H2, indicating that the carbon has been removed from the typical soot reaction pathways. In all conditions tested, PAH formed follow the typical trend observed in earlier works with respect to temperature, i.e. as the temperature increases, the formation of PAH decreases. At 1275 K, the presence of high NH₃ levels increases PAH concentrations, likely due to suppression of soot formation routes, which prevents PAH consumption and allows aromatic intermediates to accumulate rather than proceed to particle growth. The increase in NH3 concentrations at the inlet reduces the toxicity expressed as benzo[a]pyrene equivalent concentration (B[a]P-eq), under all conditions studied. Analysis of the particle distribution diameter reveals that the NH3 presence reduces diameter variations and predominantly results in smaller soot particles.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Exosomal biomarkers and therapeutics in lung cancer: a narrative review on their role in early detection and targeted treatment

  • Rodríguez-Sanz, Jorge
  • Mincholé Lapuente, Elisa
  • Polanco Alonso, Dinora
  • Viñuales Aranda, Manuel David
  • Marín-Oto, Marta
  • Domingo Morera, Juan Antonio
  • Marín Trigo, José María
  • Sanz-Rubio, David
Background and Objective: Lung cancer remains the leading cause of cancer-related mortality worldwide, largely due to late-stage diagnosis and therapy resistance. Despite advances in targeted therapies and immunotherapies, the prognosis remains poor. There is a critical need for minimally invasive biomarkers that enable early detection, prognostic stratification and therapeutic monitoring. Exosomes, a subtype of extracellular vesicles, have emerged as promising candidates in this context given their role in intercellular communication and their selective cargo, which reflects the molecular state of tumor cells. This review aims to summarize the current evidence on the potential of exosomes and their cargo, particularly microRNAs (miRNAs), as diagnostic and prognostic biomarkers as well as therapeutic tools in lung cancer. Methods: A comprehensive literature search was conducted using PubMed/MEDLINE and Scopus databases between January 3 and April 30, 2025. Studies published from January 2000 to April 2024 were included if they addressed the role of exosomes in lung cancer diagnosis, prognosis, or therapy. Two reviewers independently screened titles and abstracts and full texts were assessed based on predefined inclusion criteria. Relevant articles were also identified through reference lists. Key Content and Findings: Exosomal miRNAs (microRNAs) have shown potential as biomarkers for early detection, disease subtype classification, prognosis and therapy resistance in lung cancer. Multiple studies have identified specific miRNA signatures associated with tumor burden, histological subtypes and clinical outcomes. Exosomes also contribute actively to oncogenesis through promoting angiogenesis, epithelial-mesenchymal transition, immune evasion and drug resistance. Furthermore, exosomes are being investigated both as therapeutic targets and delivery systems due to their ability to transfer functional biomolecules selectively and safely. Despite these advances, challenges remain regarding standardization of isolation methods, heterogeneity in miRNA signatures and clinical validation. Conclusions: Exosomes represent a dynamic and promising platform for improving the diagnosis, prognosis and treatment of lung cancer. Although technical and translational hurdles remain, their integration into clinical practice may enhance personalized and precision oncology strategies. Continued research and technological advancements are necessary to fully unlock their potential in routine cancer care.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Estudio de la Descomposición Térmica del Amoníaco en un Reactor de Acero Inoxidable: Producción de amoníaco y perspectivas sostenibles

  • Zambrano Bedón, Guisela
  • Gea, Gloria
  • Fonts, Isabel
  • Ramos, Cristina
  • Millera, Angela
  • Gil-Lalaguna, Noemí
Este estudio analiza cómo la temperatura influye en la descomposición del amoníaco (NH₃) durante procesos de gasificación, utilizando un reactor tubular de acero inoxidable. En particular, se investiga el impacto del material del reactor en la conversión del amoníaco, con el objetivo de comprender cómo sus propiedades pueden afectar el comportamiento térmico de la reacción.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

En busca de las mejores condiciones para el medio ambiente y la salud humana: doctrina del TJUE sobre economía circular y residuos

  • Guerrero Manso, María del Carmen de
Los residuos son un problema constante en la Unión Europea, hasta el punto de que algunos años, como tuvimos ocasión de destacar, el porcentaje de sentencias dictadas por el Tribunal de Justicia de la Unión Europea (en adelante TJUE) en esta materia es muy alto(2). Para poner en contexto este dato, cabe recordar la importante tarea que el TJUE desempeña en su doble función esencial de garantizar la correcta interpretación del Derecho de la Unión y su aplicación homogénea en todos los Estados miembros, por un lado, y de supervisar el cumplimiento de dichas normas, por otro. Y esta doble función es muy relevante en el ámbito de los residuos, ya que son muchos y diversos los Reglamentos y Directivas aprobados en relación a esta materia. Los primeros regulan ámbitos como el traslado de residuos, los subproductos animales, el reciclado de buques o los contaminantes orgánicos persistentes(3). Las segundas abarcan aspectos como los residuos, su vertido, los envases, la utilización de sustancias peligrosas en aparatos eléctricos y electrónicos, los residuos de este tipo de aparatos, las pilas, acumuladores y sus residuos, los vehículos al final de su vida útil, la utilización de lodos de depuradora en agricultura, la gestión del combustible nuclear, de los residuos de las industrias extractivas y la eliminación de policlorobifenilos y de los policloroterfenilos(4).
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Más de una década de compra pública de innovación en salud en España: estado de la cuestión y análisis de sus resultados

  • Guerrero Manso, María del Carmen de
public procurement of innovation (PPI) in the field of healthcare has been a reality in Spain for more than 10 years now; however, its use is still often unknown. To help alleviate this situation, this article first provides an introduction to PPI, technological readiness levels (TRL) and public ways of acquiring innovation, which are essential elements for analyzing, subsequently, almost 30 cases of PPI in health organized according to their purpose. Finally, the Spanish experience of PPI in healthcare is evaluated according to four essential aspects: the awarding procedure used, the financing of these projects, the inclusion of the solutions in the health system and the evaluation of their impact. La compra pública de innovación (CPI) en el ámbito de la salud es una realidad en España desde hace ya más de diez años, sin embargo, en muchas ocasiones su utilización sigue siendo desconocida. Para ayudar a paliar esa situación, en este artículo se aborda, en primer lugar, una introducción a la CPI, a los niveles de madurez tecnológica (TRL) y a las formas públicas de adquirir innovación, elementos imprescindibles para analizar, posteriormente, casi treinta supuestos de CPI en salud organizados atendiendo a su objeto. Finalmente se valora la experiencia española de CPI en salud conforme a cuatro aspectos esenciales: el procedimiento de adjudicación utilizado, la financiación de estos proyectos, la inclusión de las soluciones en el sistema de salud y la valoración de su impacto.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Oxidation of diethyl ether/ammonia mixtures in a flow reactor at different pressures

  • García-Ruiz, P.
  • García, M.
  • Abián, M.
  • Alzueta, M.U.
Ammonia (NH3) in their mixtures with diethyl ether (DEE) represents a strategy to reduce CO2 emissions and overcome the limitations of NH3 combustion, even for a small addition of DEE (5 %). DEE is considered a potential substitute for fossil fuels when obtained from bioethanol. The present work performs an experimental and kinetic analysis of DEE/NH3 oxidation and the formation of combustion products at different pressures (1–40 bar), in the 290 K–1180 K temperature range using a quartz tubular flow reactor by analyzing the effects of the main variables (pressure, temperature, oxygen excess ratio, and DEE/NH3 ratio) using argon as a bath gas. The results indicate that either increasing pressure, DEE/NH3 ratio, or oxygen availability results in a shift of NH3 and DEE conversion to lower temperatures. DEE and NH3 show a negative temperature coefficient (NTC) phenomenon at low temperatures, influenced by pressure, oxygen excess, and the DEE/NH3 ratio. The pressure effect is particularly significant in the low pressures studied. The main nitrogen products are N2 and N2O. HCN is only produced under atmospheric pressure, while NO2 and NO concentrations are below the detection limit under all considered conditions. N2O formation is favored by increasing stoichiometry, pressure, and DEE/NH3 ratio. Apart from CO and CO2, CH4, CH3OH, C2H4, and CH3CHO have been found as produced carbon pecies. The experimental results are interpreted in terms of a chemical kinetic mechanism for DEE/NH3 mixtures, which can describe the main trend of NH3 and DEE conversion under the studied conditions.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Novel Phosphorus-Doped Magnetic and Deactivation-Resistant Solid Catalysts for Nonenzymatic Sugar Production from Biomass Hemicellulose

  • Luo, Yiping
  • Jiang, Bin
  • Remón, Javier
  • Wu, Jie
  • Zhu, Xiaoyu
  • Deng, Fang
  • Fu, Hongquan
  • Ao, Tianjie
  • Li, Dong
The development of a cost-effective process for biomass conversion into sugar platforms is a cornerstone of sustainable biorefining. Here, we report a Lewis acid-controlled catalytic strategy for nonenzymatic sugar production from hemicellulose in biomass using a highly active, magnetically separable core–shell catalyst. The catalyst comprises a Fe3O4 magnetic core, an acid-resistant silica interlayer, and a phosphorus (P)-doped porous carbon shell. Under mild hydrothermal conditions, the optimized catalyst (MC600P1.2) achieved a xylose yield of 86.9% from xylan (100 °C for 2 h) and 60.3–91.0% from diverse biomass feedstocks (corncob, corn stover, poplar, and bamboo, 160 °C for 2 h), outperforming previously reported systems. Such remarkable catalytic activity is attributed to the unique structural design of the catalyst. The silica interlayer acts as a protective shield of Fe3O4 core and bonds with the carbon layer to form a silica–carbon shell that provides an ideal scaffold. Meanwhile, P doping introduces defects and hydrogen bonds, enhancing the active site accessibility. The formation of thermally stable POx species (C–P–O, C3–P═O, and C–O–P) on the carbon support acts as Lewis acid sites. C–P–O efficiently activates H2O to produce H+ for glycosidic bond cleavage and suppresses xylose degradation, ensuring a high yield. These features result in high catalytic stability and reusability, maintaining high xylose yields after three consecutive cycles. This work provides new research avenues to produce nonenzymatic sugar based on active, deactivation-resistant, and easily recoverable heterogeneous catalysts.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Comparative study of the effects of reactor system and catalysts on glycerol valorisation via aqueous-phase reforming

  • Alves, Carine T.
  • Maldonado-Martín, Francisco
  • Lete, Alejandro
  • Hashemnezhad, Seyed Emad
  • García, Lucía
  • Onwudili, Jude A.
The conversion of glycerol through aqueous phase reforming (APR) presents an important opportunity for sustainable chemical and fuel production. This study explores the APR of glycerol using three catalysts (nickel supported on alumina (NiAl), copper supported on alumina (CuAl), and bimetallic nickel-iron supported on alumina (NiAlFe)), synthesized via the coprecipitation method. The APR experiments were conducted in both batch and fixed-bed reactors. In the batch reactor, a 75 mL Parr reactor was utilised, operating at 238 °C and 5 bar initial nitrogen pressure with 20 mL of a 5 wt% glycerol solution and 0.3 g of catalyst (catalyst/glycerol mass ratio = 0.3). The fixed-bed reactor was made of a stainless steel tube loaded with 2 g of catalyst, operating at 238 °C and 37 bar, with a continuous feed of 5 wt% glycerol solution, equivalent to catalyst/glycerol mass ratio of 0.33. NiAl produced the highest conversion of glycerol to gases and the highest yield of hydrogen (230 mg H2/mol C fed). However, among the tested catalysts, NiAlFe demonstrated superior performance, achieving a carbon yield to total products (liquid and gases) of approximately 80 % in the batch reactor as well as a relatively high hydrogen yield (141 mg H2/mol C fed). These results underscore the promising potential of the NiAlFe catalyst for efficient glycerol conversion in APR processes, paving the way for advancements in sustainable fuel and chemical production.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Valorizing Every Carbon Atom: A Cascade Bioprocess for Advanced Biofuels from Corn-Stover-Derived Lignocellulose

  • Ao, Tianjie
  • Luo, Yiping
  • Remón, Javier
  • Wu, Jie
  • Deng, Fang
  • Li, Dong
  • Liu, Chenguang
  • Bai, Fengwu
Conventional biorefining of lignocellulosic biomass, such as corn stover (CS), is hampered by poor carbon efficiency, as nearly half of the substrate carbon is lost as CO2 during ethanol fermentation. This study presents a holistically integrated cascade process designed to capture and valorize all major carbon streams. The system synergistically couples three stages: (1) high-productivity ethanol fermentation (1.68 g/L/h) using the engineered yeast Saccharomyces cerevisiae CE10; (2) anaerobic digestion of the resulting stillage, which efficiently converted residual organics into methane (171 L/kg COD) with ca. 80% COD removal; and (3) cultivation of the cyanobacterium Desertifilum tharense BERC03 using the nutrient-rich digestate and captured fermentation CO2. This integrated approach boosted the carbon utilization from a baseline of 48% to 62%. A comprehensive techno-economic analysis of an industrial-scale (2000 t/d) facility projected a Minimum Ethanol Selling Price (MESP) of $2.44 per gallon, a value approaching current market competitiveness. The analysis identified the feedstock (30%) and cellulase (17%) as the primary cost drivers. These findings demonstrate a validated biorefinery model that significantly enhances carbon recovery and outlines a viable pathway for the coproduction of multiple biofuels from lignocellulosic resources.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Experimental and modelling study of phenol combustion and oxidation

  • Delort, Nicolas
  • Meziane, Ismahane
  • Herbinet, Olivier
  • Carstensen, Hans-Heinrich
  • Battin-Leclerc, Frédérique
Despite of its central importance in the chemistry of aromatic compounds and fuels derived from biomass, only few experimental studies on phenol combustion can be found in literature. In this paper, unique measurements of the adiabatic laminar burning velocities of phenol are presented, together with the first experimental study of the oxidation of this molecule in a jet-stirred reactor. The burning velocities were measured with a flat-flame burner using the heat-flux method for a fresh gas temperature of 398 K and equivalence ratios from 0.7 to 1.35. In the reactor experiments, the oxidation of a stoichiometric mixture of phenol highly diluted in helium was investigated at temperatures between 600 and 1100 K at near-atmospheric pressure. The mole fraction of the reactants, as well as 32 products, mainly carbon monoxide, carbon dioxide, methane, acetylene ethylene, acrolein, cyclopentadiene, benzene, naphthalene and dibenzofuran, were recorded. Based on previous literature work, a new detailed kinetic model is developed based on several published sub-mechanisms and updated considering rate constants taken from recent literature studies or calculated at the CBS-QB3 or G4 level of theory. This model leads to a significantly improved prediction of the phenol burning velocities compared to literature models, as well as a reasonable prediction of most species mole fractions during phenol oxidation in the jet-stirred reactor. Sensitivity analyses as well as flow rate analyses are discussed to explain the obtained model improvements.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Energy, exergy and mass balances of a biomass pyrolysis pilot plant

  • Gracia-Monforte, César
  • Lete, Alejandro
  • Marias, Frédéric
  • Ábrego, Javier
  • Arauzo, Jesús
This work presents the methodology and results of the energy, exergy, and mass balances of a fixed-bed downdraft biomass pyrolysis pilot plant. The analysis covers different operating modes: pyrolysis without energy recovery, with energy recovery from products, and with combustion of non-condensable gases including exhaust-gas heat recovery. The proposed framework enables consistent comparison of energy and exergy performance under varying process configurations. Experimental results show that the external heat demand of the pyrolysis process strongly depends on the energy recovery strategy. When products are cooled to the reference state, the required heat input is approximately 1.3 MJ/kg, increasing to about 3 MJ/kg when products leave at the pyrolysis temperature. The combustion of process gases significantly reduces this demand, while integrating exhaust-gas heat recovery leads to quasi-autothermal operation. Exergy analysis reveals that gas combustion and heat recovery lower exergy efficiency due to the conversion of high-quality pyrogases into exhaust gases. Nevertheless, the methodology developed allows quantifying these trade-offs and provides a comprehensive tool to evaluate process integration strategies in biomass pyrolysis systems aimed at improved thermal performance and sustainability.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

A prospective review on bioplastics and biopolymers

  • Moreira, Rui
  • Atienza-Martínez, Maria
  • Gil-Lalaguna, Noemí
  • Serra, Arménio
  • Cornejo, Alfonso
  • Bimbela, Fernando
  • Coelho, Jorge
  • Gandía, Luis M.
  • Arauzo, Jesus
  • Sánchez, José Luis
The production of bioplastics has been extensively investigated in recent decades, with the purpose of reducing the global dependence on fossil resources. In this review, the main routes to produce bioplastics and a critical discussion of these technologies are presented. The synthesis routes to produce biodegradable and non-biodegradable bioplastics are discussed. Additionally, approaches to improve the environmental footprint of some conventional plastics that have no immediate solutions of substitution are also addressed. A comparison of the main properties of the bioplastics considered and a general perspective of the bioplastics market are also provided. Because these themes have often been reviewed separately, this article aims to provide a unified general perspective of bioplastics in the context of a biobased economy, as well as pointing out some of the hurdles in such way.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

The Opportunity of the Recovery and Resilience Facility and the Adaptation of the Spanish Public Procurement Framework

  • De Guerrero Manso, C.
This article analyses the objectives set out in the NextGenerationEU funds, which aim to make Europe greener, more digital and more resilient. It also analyses how Spain has responded to the need to guarantee the appropriate framework for the absorption and correct application of the funds.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Bregman Proximal Gradient with extrapolation to train a Reservoir Computing network for a binary classification task

  • Mayora-Cebollero, Carmen
  • Mayora-Cebollero, Ana
  • Lozano, Álvaro
  • Barrio, Roberto
This study examines the training process of Artificial Neural Networks, specifically focusing on Reservoir Computing and on binary classification tasks. Training involves optimizing the network’s parameters to minimize the error of a loss function, which quantifies the discrepancy between network outputs and target data. Several numerical optimizers are used in the literature. Here, we formulate the supervised learning problem using the recently introduced Bregman Proximal Gradient with extrapolation (BPGe) algorithm for non-convex optimization problems. We compare this new method with the classical Stochastic Gradient Descent (SGD), the Root Mean Square Propagation (RMSProp), the Adaptive Moment Estimation (Adam), and two variants with Nesterov momentum (NAG and NAdam). The new approach leads to an accurate and significantly faster numerical algorithm for solving supervised learning problems on binary classification tasks in Reservoir Computing. Three test examples are presented, one based on chaotic data classification in the classical Lorenz system, another on the Human Activity Recognition (HAR) using smartphones dataset for movement–rest classification, and the last one on the MNIST dataset for even–odd classification. We show that our approach is highly competitive with existing methods in the tests performed.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Almost Calabi-Yau with torsion 6-manifolds and the instanton condition

  • Ivanov, Stefan
  • Ugarte, Luis
It is observed that on a compact almost complex Calabi-Yau with torsion (ACYT) 6-manifold with co-closed Lee form the curvature of the torsion connection is an SU(3)-instanton if and only if the torsion is parallel with respect to the torsion connection. The same conclusion holds for any (non necessarily compact) balanced ACYT 6-manifold. In particular, on a CYT 6-manifold the Strominger-Bismut connection is an SU(3)-instanton if and only if the torsion is parallel with respect to the Strominger-Bismut connection provided either the CYT 6-manifold is compact with co-closed Lee form or it is a balanced CYT 6-manifold.