Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 12
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

NOx selective catalytic reduction at high temperatures with mixed oxides derived from layered double hydroxides

  • Palomares Gimeno, Antonio Eduardo|||0000-0002-6480-6607
  • Franch Martí, Cristina
  • Ribera, Antonio
  • Abellán, G.
[EN] Mixed oxides derived from layered double hydroxides (LDHs) have been investigated as potential catalysts for the NOx removal at high temperatures. The best results were obtained with Co–Al mixed oxides derived from LDHs that are active at 750 ◦C in the presence of oxygen and water. These catalysts could reduce or/and decompose the NOx formed in the dense phase of the FCC regenerator, being deactivated at oxygen concentrations higher than 1.5%. Nevertheless this deactivation is not permanent and they would be regenerated after reduction with hydrogen at 530 ◦C. The influence of the layered double hydroxides (LDHs) preparation method on the catalyst activity was studied, observing that the activity of the catalyst depends on its chemical composition but it does not depend on the initial LDHs crystallinity, obtaining similar results independently of the synthesis method., A.E. Palomares and C. Franch thank the Spanish Government (projects MAT2009-14528-C02-01 and CONSOLIDER INGENIO 2010) and the European Union (European Community's Seventh Framework Programme FP7/2007-2013 under Grant Agreement No. 226347 Project) for financial support. A. Ribera and G. Abellan acknowledge financial support from the Spanish Ministerio de Ciencia e Innovacion with FEDER co-financing (CTQ-2011-26507) and the Generalitat Valenciana (Prometeo Program).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

A study of different supports for the catalytic reduction of nitrates from natural water with a continuous reactor

  • Franch Martí, Cristina
  • Palomares Gimeno, Antonio Eduardo|||0000-0002-6480-6607
  • Corma Canós, Avelino|||0000-0002-2232-3527
[EN] The aim of this work is to study the activity for the nitrate catalytic reduction in natural water, using a continuous stirred tank reactor, of Pd/Cu and Pd/Sn catalysts supported on different materials. The studied supports are: -Al2O3 (commercial), active carbon, graphite, hydrotalcite and alumina synthesized in our laboratory with a high surface area. The activity and selectivity of the catalysts supported on these materials have been compared. The best results have been obtained with the Pd/Sn catalysts supported on alumina. These results show thatthe surface area ofthe supportis notthe only important characteristic for an active catalyst in this reaction, but also its acid–base properties, electrical conductivity and interaction with the metallic active sites are very significant. The adequate combination of these characteristics is necessary to obtain an active catalyst. The influence of the Pd/Sn content on the activity of the alumina supported catalysts was studied, observing that the best activity was obtained when the Pd/Sn ratio was higher than 1. This result clearly indicates that it is necessary to have both Pd and Pd–Sn centers in order to obtain an active catalyst., The authors thank the Spanish Government(projects MAT2009-14528-C02-01 and CONSOLIDER INGENIO 2010) and the European Union (European Community’s Seventh Framework Programme FP7/2007-2013 under Grant Agreement No. 226347 Project)for the financial support.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Characterization of (Sn and Cu)/Pd catalysts for the nitrate reduction in natural water

  • Franch Martí, Cristina
  • ENRIQUE RODRIGUEZ-CASTELLON
  • Reyes-Carmona, Álvaro
  • Palomares Gimeno, Antonio Eduardo|||0000-0002-6480-6607
[EN] The aim of this work is to characterize different (Cu and Sn)/Pd catalysts, supported on alumina, used for the catalytic removal of nitrates in natural water. The catalysts have been prepared with a Pd/(Cu or Sn) ratio of 2 but with different metal contents. Their activity and selectivity have been studied using a continuous stirred-tank reactor with nitrate polluted water from an aquifer. The catalysts have been characterized both before and after reaction by XPS, XRD, XRF, adsorption–desorption N2 isotherms at 196 ◦C and TEM. XPS results show changes of the Pd/Sn surface atomic ratio upon catalyst activation and after reaction and the coexistence of different oxidation states for the active metals. The studied catalysts are active, being the catalyst with the best performance that with the highest metallic dispersion and with the lowest phases segregation. The characterization ofthe catalysts after reaction shows that catalyst deactivation could be related with the non-reversible oxidation of the Sn–Pd couple., We gratefully acknowledge the support from the Ministry of Science and Innovation, Spain (MICINN, Spain) through the project MAT2009-10481 and FEDER funds. Authors also thank the Spanish Government (projects MAT2009-14528-C02-01 and CONSOLIDER INGENIO 2010) and the European Union (European Community's Seventh Framework Programme FP7/2007-2013 under Grant Agreement No. 226347 Project) for financial support.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Structured fibrous carbon-based catalyst for continuous nitrate removal from natural water

  • Yuranova, T.
  • Franch Martí, Cristina
  • García-Bordejé, E.
  • Kiwi-Minsker, L.
  • Palomares Gimeno, Antonio Eduardo|||0000-0002-6480-6607
[EN] Bimetallic (Pd–Cu, Pd–Sn) nanoparticles supported on structured fibrous carbons (activated carbon fibers and carbon nanofibers grown on sintered metal fibers) were tested in nitrate removal of natural polluted water by hydrogen (a batch and continuous mode). Dependence of the activity/selectivity on catalyst chemical composition, promoter nature and metal particle size was studied. Sn-modified Pd nanoparticles showed higher N2 selectivity as compared to Cu-modified ones. The structured (Pd–Sn) nanoparticles supported on carbon nanofibers grown on Inconel sintered metal fibers demonstrated the best catalytic performance in an open flow reactor, providing optimal hydrodynamics properties., This work was carried out with the financial support of the European Community's Seventh Framework Programme (FP7/2007-2013) under grant agreement no. 226347.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Efficient reduction of bromates using carbon nanofibre supported catalysts: experimental and a comparative life cycle assessment study

  • Yaseneva, Polina
  • Franch Martí, Cristina
  • Fan, Xiaolei
  • Morgan, Tobias
  • Perez, Pablo Saz
  • Ronning, Magnus
  • Huang, Fan
  • Yuranova, Tatiana
  • Kiwi-Minsker, Liubov
  • Derrouiche, Salim
  • Lapkin, Alexei A.
  • Palomares Gimeno, Antonio Eduardo|||0000-0002-6480-6607
[EN] Structured hierarchical catalysts were developed for efficient reduction of bromates in water. In the catalysts a small amount of active metal, 0.3 wt.% Pd, is supported onto carbon nanofibres grown either on sintered metal fibres or on a carbon cloth. In both cases high rates of reaction and high selectivity were achieved, allowing a significant reduction in the amount of catalyst required for the treatment of a set volumetric flow of polluted water, compared to a conventional Pd/Al2O3 catalyst. Manufacture of carbon nanofibres grown on a hierarchical structured support was scaled to 10 g batches. Cradle-to-gate life cycle assessment (LCA) study was performed to compare potential water treatment processes based on two catalyst types, and to identify the areas for future optimisation of the novel technology based on structured hierarchical catalysts., The research leading to these results has received funding from the European Community's Seventh Framework Programme [FP7/2007-2013] for MONACAT under Grant agreement no NMP4-SL-2009-226347. We would like to thank Drs Dana Kralisch and Denise Ott for their advice on Umberto LCA methods.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

The use of Pd catalysts on carbon-based structured materials for the catalytic hydrogenation of bromates in different types of water

  • Palomares Gimeno, Antonio Eduardo|||0000-0002-6480-6607
  • Franch Martí, Cristina
  • Yuranova, Tatiana
  • Kiwi-Minsker, Liouba
  • Garcia Bordeje, Jose Enrinque
  • Derrouiche, Salim
[EN] The aim of this work is to study the activity of new Pd catalysts, supported on two different nano structured carbon materials, for bromate catalytic hydrogenation. The influence of the support has been studied, obtaining the best results with a palladium catalyst supported on carbon nanofibers (CNF) grown in sintered metal fibers (SMF). The results have shown the importance of the catalyst support in order to minimize the mass-transfer limitations ensuring an efficient catalyst use. In this way the most active catalysts are those with a mesoporous structure containing high dispersed Pd nanoparticles. The activity of this catalyst for bromate reduction has been tested in different types of water, namely, distilled water, natural water and industrial wastewater. It has been shown that the catalyst activity depends on the water matrix and bromate reduction rate depends on the hydrogen partial pressure. The potential use of the catalyst has been studied in a continuous reactor. It has been observed that the catalyst is active without any important deactivation at least during 100 h of reaction, but is necessary to avoid salt precipitation and plugging problems., The authors thank the European Union (European Community's Seventh Framework Programme FP7/2007-2013 under grant agreement no. 226347 Project) for financial support. A.E. Palomares also acknowledges the support from the Spanish Government through the project MAT2012-38567-C02-01.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Simulation of catalytic reduction of nitrates based on a mechanistic model

  • Fan, Xiaolei
  • Franch Martí, Cristina
  • Lapkin, Alexei A.
  • Palomares Gimeno, Antonio Eduardo|||0000-0002-6480-6607
[EN] A model including coupled surface reactions, liquid-phase equilibrium and mass transfer steps was developed for the reaction of catalytic reduction of nitrates with H 2 over bimetallic catalysts. The model was constructed from the molecular mechanism of NO 3 - and NO 2 - reduction including description of the roles of mono- and bimetallic active sites. The model was validated against experimental data and was used to obtain detailed information on the concentrations of surface species, thus providing mechanistic insights into the influence of operating conditions on reactivity and selectivity. Simulation of the model with different experimental conditions showed that the presence of external mass transfer resistances strongly affects the surface species NO * and NH * and results in deterioration of selectivity to N 2. The obtained knowledge is being used to design a more optimised 'reaction environment' in the specific case of the nitrates reduction reaction, using new capabilities of nano-scale materials and process intensification. A modeling approach adopted in this study can be generalised as a methodology of investigating complex reaction systems., This work was supported by the European Community's Seventh Framework Programme under project "MONACAT", Grant agreement No. 226347.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Bromate catalytic reduction in continuous mode using metal catalysts supported on monoliths coated with carbon nonofibers

  • Marco, Yanila
  • García-Bordejé, Enrique
  • Franch Martí, Cristina
  • Yuranova, Tatiana
  • Kiwi-Minsker, Liouba
  • Palomares Gimeno, Antonio Eduardo|||0000-0002-6480-6607
[EN] Nitrogen-doped and un-doped carbon nanofibers layers, denoted as N-CNFs and CNFs respectively, coating the walls of cordierite monoliths have been used as support for Pd and Ru catalyst. They have been tested in bromate reduction in batch and continuous operation employing different reactor configurations. The CNF/monolith catalysts were benchmarked with Pd catalyst on CNF coated on another structured support, namely sintered metal fibers. CNF/monolith is a robust, active and stable catalyst for bromate reduction. The catalyst shows stable performance when operating in monolithic reactor and the CNFs showed excellent attachment to the monolith. The comparison of intrinsic activity of catalysts in batch experiments (free of diffusional limitations) revealed that Pd supported on CNF/monolith exhibited higher intrinsic activity than Pd on CNF/SMFs. Pd metal showed significantly higher specific activity than Ru. The doping of CNF with nitrogen, although contribute to decrease reoxidation propensity of metal does not supplies higher activity in bromate reduction., The authors thank the European Union (European Community’s Seventh Framework Programme FP7/2007-2013 under Grant Agreement No. 226347 Project) for financial support.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Control of nitrogen insertion during the growth of nitrogen-containing carbon nanofibers on cordierite monolith walls

  • Roldán, Laura
  • Armenise, Sabino
  • Marco, Yanila
  • García-Bordejé, José Enrique
First published online Jan. 16, 2012, A well attached coating of nitrogen-functionalised carbon nanofibers (N-CNFs) has been prepared on the walls of cordierite monolith channels. It is formed via concurrent decomposition of ethane and ammonia catalysed by nickel nanoparticles dispersed on alumina coated cordierite monolith. N-CNF/monoliths synthesis employing several growth temperatures and NH 3 compositions was exhaustively characterised by Raman, XPS, elemental analysis and TEM. Synthesis conditions affected profoundly content and type of nitrogen functionality, enabling its fine tuning. N-CNFs surface chemistry and microstructure differed remarkably from its N-free counterparts., The authors are grateful to the financial support of the European Commission within the 7th FP (Grant agreement no.: 226347) and of Spanish Government (MAT 2008-02365)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

The formation of a hydrothermal carbon coating on graphite microfiber felts for using as structured acid catalyst

  • Roldán, Laura
  • Santos, Iván
  • Armenise, Sabino
  • Fraile, José M.
  • García-Bordejé, José Enrique
10 Figuras.- Información suplementaria disponible en la página web del editor., A hydrothermal carbon layer has been coated on graphite felt using a carbohydrate solution (glucose, sucrose or starch) as precursor. The coating is uniform in thickness and coverage, and exhibits excellent adhesion to the substrate. It is highly hydrophilic, very accessible to reactants and the thickness can be tuned by the synthesis conditions. The coating was functionalized with sulfonic acid groups and its morphology and surface chemistry characterized by SEM, TPO-MS, IR-spectroscopy and XPS. The sulfonated material has been tested in the esterification of palmitic acid with methanol exhibiting significant activity and stability., This work has been possible thanks to the financial support of Aragón regional government (PI050/09), Spanish national government (MAT 2008-02365, CTQ2008-05138, Consolider Ingenio 2010 INTECAT CSD2006-0003) and European Commission (Grant agreement No. 226347)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

The use of Pd catalysts on carbon-based structured materials for the catalytic hydrogenation of bromates in different types of water

  • Palomares, A. E.
  • Franch, C.
  • Yuranova, T.
  • Kiwi-Minsker, L.
  • García-Bordejé, José Enrique
  • Derrouiche, S.
6 pages, 2 tables., The aim of this work is to study the activity of new Pd catalysts, supported on two different nano structured carbon materials, for bromate catalytic hydrogenation. The influence of the support has been studied, obtaining the best results with a palladium catalyst supported on carbon nanofibers (CNF) grown in sintered metal fibers (SMF). The results have shown the importance of the catalyst support in order to minimize the mass-transfer limitations ensuring an efficient catalyst use. In this way the most active catalysts are those with a mesoporous structure containing high dispersed Pd nanoparticles. The activity of this catalyst for bromate reduction has been tested in different types of water, namely, distilled water, natural water and industrial wastewater. It has been shown that the catalyst activity depends on the water matrix and bromate reduction rate depends on the hydrogen partial pressure. The potential use of the catalyst has been studied in a continuous reactor. It has been observed that the catalyst is active without any important deactivation at least during 100. h of reaction, but is necessary to avoid salt precipitation and plugging problems., The authors thank the European Union (European Community’s Seventh Framework Programme FP7/2007-2013 under Grant Agreement No. 226347 Project) for financial support., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Towards practical application of H2 generation from ammonia decomposition guided by rational catalyst design

  • García-Bordejé, José Enrique
This perspective article focuses on the recent advances in the rational design of catalyst for NH3 decomposition at different length scales, from catalyst nanoparticles to reactor design. For an overall optimum performance, all scales should be optimised in a concerted manner. The study of the mechanism of reaction has given guidelines for the catalyst design. As far as reactor design is concerned, a structured reactor is beneficial for this reaction because minimises the inhibiting effect of produced H2, besides other inherent advantages. This holistic optimisation of catalysts, it is expected to pave the way for application of NH3 as H2 storage media., The authors are grateful to the financial support of the European Commission within the 7th FP (Grant agreement no.: 226347)., Peer reviewed