Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 24
Encontrada(s) 1 página(s)

Addi. Archivo Digital para la Docencia y la Investigación
Publication Artículo científico (JournalArticle)

Network dynamics in nanofilled polymers

  • Baeza, Guilhem P
  • Dessi, Claudia
  • Costanzo, Salvatore
  • Zhao, Dan
  • Gong, Shushan
  • Alegría Loinaz, Angel María
  • Colb, Ralph H.
  • Rubinstein, Michael
  • Vlassopoulos, Dimitris
  • Kumar, Sanat K.
It is well accepted that adding nanoparticles (NPs) to polymer melts can result in significant property improvements. Here we focus on the causes of mechanical reinforcement and present rheological measurements on favourably interacting mixtures of spherical silica NPs and poly(2-vinylpyridine), complemented by several dynamic and structural probes. While the system dynamics are polymer-like with increased friction for low silica loadings, they turn network-like when the mean face-to-face separation between NPs becomes smaller than the entanglement tube diameter. Gel-like dynamics with a Williams-Landel-Ferry temperature dependence then result. This dependence turns particle dominated, that is, Arrhenius-like, when the silica loading increases to similar to 31 vol%, namely, when the average nearest distance between NP faces becomes comparable to the polymer's Kuhn length. Our results demonstrate that the flow properties of nanocomposites are complex and can be tuned via changes in filler loading, that is, the character of polymer bridges which 'tie' NPs together into a network., We thank Leon Serc (ETH Zurich) for help with FTIR. Enlightening discussions with Ulrich Jonas are gratefully acknowledged. Partial support has been provided by the EU FP7 (ETN Supolen GA-607937, Infrastructure ESMI GA-262348) and the Greek General Secretariat for Research and Technology (Thalis-380238 COVISCO). M.R. acknowledges financial support from the National Science Foundation under grants DMR-1309892, DMR-1436201 and DMR-1121107, the National Institutes of Health under grants P01-HL108808 and 1UH2HL123645 and the Cystic Fibrosis Foundation. D.Z., S.G., R.H.C. and S.K.K. gratefully acknowledge the National Science Foundation grant DMR-1408323 for financial support.
Investigo. Repositorio Institucional de la Universidade de Vigo
Publication Artículo científico (JournalArticle)

Three-dimensional elemental mapping at the atomic scale in bimetallic nanocrystals

  • Goris, Bart
  • De Backer, Annick
  • Aert, Sandra Van
  • Gómez Graña, Sergio
  • Liz Marzán, Luis Manuel
  • Van Tendeloo, Gustaaf
  • Bals, Sara
A thorough understanding of the three-dimensional (3D) atomic structure and composition of core-shell nanostructures is indispensable to obtain a deeper insight on their physical behavior. Such 3D information can be reconstructed from two-dimensional (2D) projection images using electron tomography. Recently, different electron tomography techniques have enabled the 3D characterization of a variety of nanostructures down to the atomic level. However, these methods have all focused on the investigation of nanomaterials containing only one type of chemical element. Here, we combine statistical parameter estimation theory with compressive sensing based tomography to determine the positions and atom type of each atom in heteronanostructures. The approach is applied here to investigate the interface in core-shell Au@Ag nanorods but it is of great interest in the investigation of a broad range of nanostructures.
Investigo. Repositorio Institucional de la Universidade de Vigo
Publication Artículo científico (JournalArticle)

Au@Ag nanoparticles: halides stabilize {100} facets

  • Gómez Graña, Sergio
  • Goris, Bart
  • Altantzis, Thomas
  • Fernández López, Cristina
  • Carbó Argibay, Enrique
  • Guerrero Martínez, Andrés
  • Almora Barrios, Neyvis
  • López, Nuria
  • Pastoriza Santos, Isabel
  • Pérez Juste, Jorge
  • Bals, Sara
  • Van Tendeloo, Gustaaf
  • Liz Marzán, Luis Manuel
Seed-mediated growth is the most efficient methodology to control the size and shape of colloidal metal nanoparticles. In this process, the final nanocrystal shape is defined by the crystalline structure of the initial seed as well as by the presence of ligands and other additives that help to stabilize certain crystallographic facets. We analyze here the growth mechanism in aqueous solution of silver shells on presynthesized gold nanoparticles displaying various well-defined crystalline structures and morphologies. A thorough three-dimensional electron microscopy characterization of the morphology and internal structure of the resulting core–shell nanocrystals indicates that facets are preferred for the outer silver shell, regardless of the morphology and crystallinity of the gold cores. These results are in agreement with theoretical analysis based on the relative surface energies of the exposed facets in the presence of halide ions.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Dynamics of poly(butylene oxide) well above the glass transition. A fully atomistic molecular dynamics simulation study

  • Colmenero de León, Juan
  • Brodeck, Martin
  • Arbe, Arantxa
  • Richter, Dieter
We present fully atomistic molecular dynamics simulations on poly(butylene oxide) (PBO) at a temperature well above the glass transition. The cell is validated by direct comparison of the calculated intermediate incoherent scattering functions of the hydrogens with those obtained from quasielastic neutron scattering (QENS) measurements [ Gerstl, C.; Macromolecules 2012, 45, 7293 ]. The information contained in the simulated atomic trajectories is first used to check the validity and explore the limits of the model used to interpret the QENS results of that work, which extended also to other members of the series of poly(alkylene oxide)s. Furthermore, the details of the segmental dynamics and the localized motions undergone by the side groups are unveiled from the simulations. Full rotations of the pendant groups take place during the decaging of the main-chain segments. © 2013 American Chemical Society., We thank support by the SoftComp Network and the projects MAT2012-31088 and IT-436-07 (GV)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Study of the dynamic heterogeneity in poly(ethylene-ran-vinyl acetate) copolymer by using broadband dielectric spectroscopy and electrostatic force microscopy

  • Kummali, Mohammed M.
  • Alegría, Ángel
  • Miccio, Luis A.
  • Colmenero de León, Juan
Dynamic heterogeneities in ethylene-vinyl acetate (EVA) random copolymers were studied using broadband dielectric spectroscopy (BDS) over a broad frequency and temperature range. BDS data for EVA copolymers show relatively broad spectra extending over several frequency decades, which make interpretation of the data complicated. Thus, microscopic dielectric characterizations of the samples were done using single pass electrostatic force microscopy (SP-EFM) images. From these experiments two distinct dielectric contributions were found in the semicrystalline samples. Dielectric spectra of EVA copolymers were fitted using a model based on the SP-EFM images. According to this analysis, the broad dielectric responses of semicrystalline EVA copolymers were constituted from two dielectrically active phases, referred to as the constrained and nonconstrained phases, exhibiting different segmental relaxations. In the constrained phase, vinyl acetate (VA) motions were greatly restricted by crystalline microstructures, whereas in the nonconstrained phase, VA monomers were assumed to be completely free from crystalline effect. The glass transition temperature derived from the dynamics of the VA segments in the constrained phase was found to correspond well with that determined from DSC representing the overall amorphous phase in the more crystallized state. Moreover, crystallinity of the sample obtained using DSC was found to follow a similar variation with temperature to that of the dielectric relaxation strength of the constrained phase of the copolymers. However, at the earlier stage of crystallization, where crystallinity increases rapidly, the dielectric relaxation remains insensitive to it. © 2013 American Chemical Society., We acknowledge the financial support from Projects No. MAT2012-31088 (Spanish Government), No. IT654-13 (Basque Government), and the European Soft Matter Infrastructure (ESMI) Program (Grant Agreement number: 262348)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Local mechanical and dielectric behavior of the interacting polymer layer in silica nano-particles filled SBR by means of AFM-based methods

  • Kummali, Mohammed M.
  • Miccio, Luis A.
  • Schwartz, Gustavo A.
  • Alegría, Ángel
  • Colmenero de León, Juan
  • Otegui, Jon
  • Petzold, Albrecht
  • Westermann, Stephan
Filler-polymer interactions in reinforced rubbers are mainly governed by a thin layer of polymer around the filler particles. The dynamics of this layer has long been a matter of intense investigation. Some researchers suggest that this >interacting layer> is immobilized and possesses slower dynamics compared to the bulk, whereas some others consider it equally mobile. In this work, we address this problem by studying the macroscopic characteristics of reinforced rubber using Broadband Dielectric Spectroscopy (BDS) and by measuring its local dielectric behavior using a new AFM based approach: nano-dielectric spectroscopy. This new approach enables us to study the dielectric response of the interacting polymer layer and the bulk dynamics locally, with a spatial resolution of about 20-30 nm. The total amount of interacting polymer within the compounds was also obtained by analyzing the local mechanical properties. Both macro- and nano-measurements show no differences in the polymer local dynamics for the compounds here analyzed. We propose that, for our particular system, the interacting polymer layer shares the same local relaxation dynamics with the bulk rubber due to the presence of a flexible link between the polymer chains and the nanoparticles. © 2013 Elsevier Ltd. All rights reserved., The authors gratefully acknowledge the support of the Spanish Ministry of Education (MAT 2012-31088) and the Basque Government (IT-436-07). ESMI (262348) financial support is also acknowledged., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Dielectric spectroscopy at the nanoscale by atomic force microscopy: A simple model linking materials properties and experimental response

  • Miccio, Luis A.
  • Kummali, Mohammed M.
  • Schwartz, Gustavo A.
  • Alegría, Ángel
  • Colmenero de León, Juan
The use of an atomic force microscope for studying molecular dynamics through dielectric spectroscopy with spatial resolution in the nanometer scale is a recently developed approach. However, difficulties in the quantitative connection of the obtained data and the material dielectric properties, namely, frequency dependent dielectric permittivity, have limited its application. In this work, we develop a simple electrical model based on physically meaningful parameters to connect the atomic force microscopy (AFM) based dielectric spectroscopy experimental results with the material dielectric properties. We have tested the accuracy of the model and analyzed the relevance of the forces arising from the electrical interaction with the AFM probe cantilever. In this way, by using this model, it is now possible to obtain quantitative information of the local dielectric material properties in a broad frequency range. Furthermore, it is also possible to determine the experimental setup providing the best sensitivity in the detected signal. © 2014 AIP Publishing LLC., We acknowledge the financial support provided by the Basque Country Government (IT-654-13) and the Spanish Ministry of Science and Innovation (MAT2012-31088). Financial support from EU-funded “European soft matter infrastructure” (reference 262348 ESMI) is also acknowledged., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

AFM based dielectric spectroscopy: Extended frequency range through excitation of cantilever higher eigenmodes

  • Miccio, Luis A.
  • Kummali, Mohammed M.
  • Schwartz, Gustavo A.
  • Alegría, Ángel
  • Colmenero de León, Juan
In the last years, a new AFM based dielectric spectroscopy approach has been developed for measuring the dielectric relaxation of materials at the nanoscale, the so called nanoDielectric Spectroscopy (nDS). In spite of the effort done so far, some experimental aspects of this technique remain still unclear. In particular, one of these aspects is the possibility of extending the experimental frequency range, to date limited at high frequencies by the resonance frequency of the AFM cantilever as a main factor. In order to overcome this limitation, the electrical excitation of cantilever higher eigenmodes for measuring the dielectric relaxation is here explored. Thus, in this work we present a detailed experimental analysis of the electrical excitation of the cantilever second eigenmode. Based on this analysis we show that the experimental frequency range of the AFM based dielectric spectroscopy can be extended by nearly two decades with a good signal-to-noise ratio. By using the combination of first and second cantilever eigenmodes we study dissipation processes on well known PVAc based polymeric samples. Both, relaxation spectra and images with molecular dynamics contrast were thus obtained over this broader frequency range., We acknowledge the financial support provided by the Basque Country Government (IT-654-13) and the Spanish Ministry of Science and Innovation (MAT2012-31088). Financial support from EU-funded ‘European Soft Matter Infrastructure’ (Reference 262348 ESMI) is also acknowledged., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Component dynamics in nanostructured PI-PDMS diblock copolymers with PI segregated in lamellas, cylinders, and spheres

  • Alegría, Ángel
  • Lund, Reidar
  • Barroso-Bujans, Fabienne
  • Arbe, Arantxa
  • Colmenero de León, Juan
The dynamics of the two components of self-assembled diblock polyisoprene (PI)-polydimethylsiloxane (PDMS) copolymers is investigated by means of broadband dielectric spectroscopy. By varying the size of the PDMS blocks, different PI segregation geometries are obtained, namely lamellas, cylinders, and spheres, with typical sizes in the range 6–16 nm. In this way, we identify the effects of the nanostructure on the dielectric relaxation of the polymer components: the α-relaxation of PI and PDMS blocks as well as the normal mode of PI blocks. Two different situations are explored: (1) the PDMS dynamics is detected in a temperature range where the PI phase is frozen and (2) the PI dynamics is detected in a temperature range where the PDMS phase is highly mobile. Thus, using a single system, the similarities and differences between hard and soft confinement are investigated., We thank the support of the following research projects MAT2012-31088 supported by the Spanish Ministry “Ministerio de Economía y Competitividad” and IT-654-13 supported by the Basque Government. We also acknowledge partial financial support by the European Soft Matter Infrastructure project (ESMI) (Grant Agreement Number: 262348)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Formation of titanium nanostructures on block copolymer templates with varying molecular weights

  • Kreuzer, Martin
  • Simao, Claudia
  • Díaz, Ana
  • Sotomayor Torres, C. M.
A novel and simple method for producing mesoporous titanium films and supported titanium nanoparticle hexagonal arrays is presented. During evaporation on block copolymer templates, titanium self-assembles as either a mesoporous film or as a hexagonal close-packed nanodot structure. The morphology of the titanium only depends on the molecular weight of the block copolymer, which results in a remarkable fabrication technique that saves time relative to conventional methods. Analyses using scanning electron microscopy, X-ray reflectometry, and grazing-incidence small-angle X-ray scattering correlate the morphology of the titanium with the buried polymer structure. The mesoporous titanium film exhibited a pore size of approximately 16 nm, with a pore-to-pore distance of 42 nm. The average size of the hexagonally packed nanodots was 60 nm, with a center-to-center distance of 88 nm commensurate with the template features. An analysis of the chemical composition showed that the structures were titanium dioxide, which indicated that oxidation occurred during the fabrication process., The authors acknowledge financial support from the EU-FP7 Integrated Infrastructure Initiative No. 262348 from the European Soft Matter Infrastructure (ESMI), LAMAND (Grant No. 245565), MERGING (Grant No. 309150), the Spanish MINECO project TAPHOR (MAT2012−31392), and the Deutsche Forschungsgemeinschaft (Grant No. KR 4522/1-1)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

A high-temperature dielectric process as a probe of large-scale silica filler structure in simplified industrial nanocomposites

  • Baeza, Guilhem P.
  • Oberdisse, Julian
  • Alegría, Ángel
  • Couty, Marc
  • Genix, A. C.
The existence of two independent filler-dependent high-temperature Maxwell-Wagner-Sillars (MWS) dielectric processes is demonstrated and characterized in detail in silica-filled styrene-butadiene (SB) industrial nanocomposites of simplified composition using Broadband Dielectric Spectroscopy (BDS). The uncrosslinked samples are made with 140 kg mol-1 SB-chains, half of which carry a single graftable end-function (50% D3), and Zeosil 1165 MP silica incorporated by solid-phase mixing. While one high-temperature process is known to exist in other systems, the dielectric properties of a new silica-related process - strength, relaxation time, and activation energy - have been evidenced and described as a function of silica volume fraction and temperature. In particular, it is shown that its strength follows a percolation behavior as observed with the ionic conductivity and rheology. Moreover, activation energies show the role of polymer layers separating aggregates even when they are percolated. Apart from simultaneous characterization over a broad frequency range up to local polymer and silanol dynamics, it is believed that such high-temperature BDS-measurements can thus be used to detect reorganizations in structurally-complex silica nanocomposites. Moreover, they should contribute to a better identification of dynamical processes via the described sensitivity to structure in such systems., We are thankful for a ‘‘Chercheur d’Avenir’’ grant by the Languedoc-Roussillon region (J.O.) and PhD funding ‘‘CIFRE’’ by Michelin (G.P.B.). The authors acknowledge financial support from the European Commission under the Seventh Framework Program by means of the grant agreement for the Integrated Infrastructure Initiative No. 262348 European Soft Matter Infrastructure (ESMI)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Depercolation of aggregates upon polymer grafting in simplified industrial nanocomposites studied with dielectric spectroscopy

  • Baeza, Guilhem P.
  • Oberdisse, Julian
  • Alegría, Ángel
  • Saalwächter, Kay
  • Couty, Marc
  • Genix, A. C.
The dynamics of polymer and filler in simplified industrial silica-styrene-butadiene nanocomposites (silica Zeosil 1165 MP, volume fraction 0-21%v) have been studied with broadband dielectric spectroscopy (BDS) and nuclear magnetic resonance (NMR). The fraction of graftable matrix chains was varied from 0 to 100%D3. The introduction of silica nanoparticles is shown to leave the segmental relaxation unaffected, an observation confirmed by the measurement of only a thin (some Angstroms thick) immobilized layer by NMR. The low-frequency measurements are resolved in two distinct dielectric Maxwell-Wagner-Sillars (MWS) processes of different behavior with respect to changes of large-scale silica structures induced by variations of filler fraction and grafting. It is found that increasing grafting leaves the first MWS-process unaffected, while it decreases the strength of the (slower) second MWS by about a decade. At constant silica volume fraction, this indicates depercolation of the filler, thereby providing a microscopic explanation of the evolution of rheological reinforcement. The sensitivity to large-scale reorganizations together with a characterization of local polymer dynamics provides insight over many length- and time-scales into structure and dynamics of nanocomposites, and thus the physical origin of the reinforcement effect., We are thankful for a “Chercheur d'Avenir” grant by the Languedoc-Roussillon region (J.O.) and Ph.D. funding “CIFRE” by Michelin (G.P.B.). The authors acknowledge financial support from the European Commission under the Seventh Framework Program by means of the grant agreement for the Integrated Infrastructure Initiative N. 262348 European Soft Matter Infrastructure (ESMI)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Determination of filler structure in silica-filled SBR compounds by means of SAXS and AFM

  • Otegui, Jon
  • Miccio, Luis A.
  • Arbe, Arantxa
  • Schwartz, Gustavo A.
  • Meyer, Mathias
  • Westermann, Stephan
The structure of the silica particles network in two different solution styrene-butadiene rubbers (S-SBRs) was studied by means of small-angle X-ray scattering (SAXS) and atomic force microscopy (AFM). S-SBR compounds with different silica contents were analyzed in comparison with their oil extended counterparts. A study into the application of SAXS experiments was defined to quantify the structures of silica primary particles and clusters in filled rubber compounds up to very high levels of filler content. We propose a modified structure model that is physically more sound than the widely used Beaucage model and that leads to more robust quantification of the silica structures. In addition, an independent characterization of the filler structure was performed by means of AFM. The cluster and particle sizes deduced from both techniques are in close agreement, supporting the proposed approach. The synergetic application of SAXS and AFM allows a consistent and robust characterization of primary particles and clusters in terms of size and structure. These results were compared and discussed in the framework of previously published works., The authors gratefully acknowledge the support of the Spanish Ministry of Education(MAT2012-31088), Basque Government (IT-436-07), and Luxembourgish Fonds National de la Recherche. Financial support from European Union–funded ‘‘ European soft matter infrastructure’’(reference 262348 ESMI) is also acknowledged., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Fluorinated networks dynamics studied by means of broadband dielectric spectroscopy

  • Miccio, Luis A.
  • Otegui, Jon
  • Schwartz, Gustavo A.
The influence of the surface chemical modification on the bulk behavior of epoxy based networks has been studied. In particular, the bulk dynamics of epoxy-amine networks modified with fluorinated side chains has been characterized by means of broadband dielectric spectroscopy (BDS), differential scanning calorimetry (DSC) and Fourier transform infrared (FTIR) spectroscopy. The fluorination effect on the structure and dynamics of the materials has been related with the observed changes in both segmental and secondary relaxations. An acceleration of the segmental dynamics as the fluorination degree increases has been clearly observed. As a result, a compromise between fluorine surface enrichment and bulk modification has been proposed for these materials., The authors acknowledge the financial support provided by the Basque Country Government (IT-654-13) and the Spanish Ministry of Science and Innovation (MAT2012-31088). Financial support from EU-funded “European soft matter infrastructure” (Reference 262348 ESMI) is also acknowledged., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Investigation of water diffusion mechanisms in relation to polymer relaxations in polyamides

  • Preda, Florentina-Maria
  • Alegría, Ángel
  • Fillot, Louise-Anne
  • Sotta, Paul
et al., Diffusion in semicrystalline polymers is a complex phenomenon because of the existence of specific interactions (nonpolar or polar), dynamic heterogeneities, and crystalline phases. The diffusion of water in two semicrystalline polyamides (PA6,6 and PA6,10) was investigated in order to determine the diffusion mechanisms and the influence of polymer relaxations on this process. Liquid water diffusion follows a Fickian mechanism in PA6,10 and a non-Fickian or anomalous mechanism in PA6,6. Through a quasi-equilibrium experiment in dynamic vapor sorption, it is shown that this difference results from the dependence of the diffusion coefficients on water concentration. Moreover, the influence of the polymer relaxations was assessed by broadband dielectric spectroscopy. The dielectric characteristic relaxation times of the α relaxation, associated with the glass transition, and of the β relaxation, related to more local dynamics, have been measured. A simple comparison with the time scale of diffusion suggests that diffusion and polyamide α relaxation should not be directly correlated. However, diffusion is correlated to the secondary β relaxation, which encompasses the local chain dynamics of hydrogen-bonded amide groups in the presence of water. A mechanism of diffusion based on the trapping of water molecules between neighboring sorption sites (amide groups) is proposed in these strongly interacting polymers. It is suggested that diffusion is limited by the relaxation time of hydrogen bonds between water molecules and amide groups and the change in conformation of these amide groups present in polyamides., Funded by the European Soft Matter Infrastructure (ESMI) program (grant no. 262348)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Real-space analysis of branch point motion in architecturally complex polymers

  • Bačová, Petra
  • Moreno Segurado, Ángel J.
By means of large-scale molecular dynamics simulations, we investigate branch point motion in pure branched polymers and in mixtures of stars and linear chains. We perform a purely geometrical density-based cluster analysis of the branch point trajectories and identify regions of strong localization (traps). Our results demonstrate that the branch point motion can be described as the motion over a network of traps at the time scales corresponding to the reptation regime. Residence times within the traps are broadly distributed, even extending to times much longer than the side-arm relaxation time. The distributions of distances between consecutively visited traps are very similar for all the investigated branched polymers, even though tube dilation is much stronger in the star/linear mixtures than in the pure branched systems. Our analysis suggests that the diffusivity of the branch point introduced by hierarchical models must be understood as a parameter to account for the effective friction associated with the relaxed side arm, more than the description of a hopping process with a precise time scale., We acknowledge support from projects FP7-PEOPLE-2007-1-1-ITN (DYNACOP, EU), MAT2012-31088 (Spain), and IT654-13 (GV, Spain). We acknowledge the programs PRACE, HPC-Europa2 and ESMI (EU), and ICTS (Spain) for generous allocation of CPU time at GENCI (France), HLRS and FZJ-JSC (Germany), and CESGA (Spain)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Tesis doctoral (DoctoralThesis)

Computational investigation of chain dynamics in architecturally complex polymers

  • Bačová, Petra
We investigate the chain dynamics in the polymer melts with complex architecture by means of molecular dynamics simulations. Our study is focused on the following architecturally complex polymers: T- and Y-shaped asymmetric stars, symmetric stars, mixtures of Tshaped asymmetric stars and linear chains, H-polymers, combs and Cayley trees. Dynamics in these architectures is strongly influenced by the presence of one or more branchpoints. The overall chain dynamics in branched structures is slowed down comparing to the linear chain and the relaxation of these materials extend over several time decades. Extensive molecular dynamics simulations allow us to study the relaxation processes ocurring in the branched polymer melts at the molecular level. We pay particular attention to the role of the branchpoint in the dynamics of these systems. Our simulations reveal details about the branchpoint motion that can be further compared to the theoretical hypotheses, experimental data and finally introduced in the predictions of the viscoelastic properties of the industrially produced materials. The time evolutions of the mean squared displacements of the particular molecular segments confirm that the arm retraction is the main relaxation mechanism in symmetric systems, i.e. symmetric stars and Cayley trees. In these systems the branchpoint remains localized during the whole simulation time. We study the role of constraint release on the branchpoint dynamics and compare the simulation results with a theoretical model. The fluctuations of the branchpoint at time scales smaller than the Rouse time τR are affected by the early tube dilation process that leads to a weaker branchpoint localization than expected. After the incorporation of the early and late tube dilation processes quantified from the simulation data into the theoretical model, we were able to fully describe the branchpoint dynamics at the times smaller than τR. After the relaxation of the short side arms in the asymmetric structures the arms act as sources of friction and the whole molecule can be described as an effective linear chain. We studied the diffusion of the branchpoint after the arm relaxation. The calculation of the diffusion constant involves the knowledge about the arm relaxation, dilution of the tube and the friction related to the reptation of the molecule. We estimated these observables from the simulations and tested theoretical hypotheses used for the prediction of the branchpoint diffusive behaviour in experimental studies of branched polymer melts. We perform a detailed analysis of the branchpoint trajectories and present a robust method for finding regions of strong localization. We characterize the time and length scales for the branchpoint motion between traps of localization, and discuss the consequences for the interpretation of the long-time branchpoint motion dynamics proposed by hierarchical tube models., This thesis would have not been possible without the financial support from projects FP7-PEOPLE-2007-1-1-ITN (DYNACOP, EU), MAT2012-31088 (Spain) and IT654-13 (GV, Spain). I would like to acknowledge the programs PRACE, HPC-Europa2 and ESMI (EU), and ICTS (Spain) for generous allocation of CPU time at GENCI (France), HLRS and FZJ-JSC (Germany) and CESGA (Spain)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Titanium particle incorporation in block copolymer templates

  • Kreuzer, Martin
  • Simao, Claudia
  • Díaz, Ana
  • Sotomayor Torres, C. M.
Template-directed formation of titanium structures on block copolymer templates has been recently reported [1]. Here, the incorporation of titanium in a thin film template is studied. We show that the surface free energy contrast in microphase-separated polystyrene-block-polyethylene oxide templates is not limited to the template film surface, but directs the assembly of titanium atoms in the template thin film. The details of the self-assembly of titanium particles on the block copolymer nanostructured surface and inside the 3D film structure are studied with selected amounts of titanium. Evaporated titanium preferentially wets the polystyrene block of the block copolymer film and diffuses inside the film, conserving the block copolymer nanostructure. Increasing deposition leads to the formation of a mesoporous titanium layer on the block copolymer film, which reproduces that of the underlying template, in this particular case with a thickness of 12 nm and a periodic pore-to-pore distance of 35 nm. The formation of a mesoporous titanium layer prevents from further titanium diffusion inside the block copolymer film. The combination of the X-ray scattering techniques presented here provides sufficient sensitivity to follow the titanium formation in the three dimensional network of the block copolymer films., The authors acknowledge the financial support from the European Commission FP7 for the Integrated Infrastructure Initiative N. 262348 European Soft Matter (ESMI) and projects LAMAND (GA No. 245565), QUANTIHEAT (GA No. 604668) and MERGING (GA No. 309150). The Spanish MINECO project TAPHOR (MAT2012–31392) and the Deutsche Forschungsgemeinschaft (Grant No. KR 4522/1-1) are also acknowledged. The work at ICN2 is partially supported by the Spanish MINECO Severo Ochoa Centres of Excellence (SEV-2013-0295)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Cl-capped CdSe nanocrystals via in situ generation of chloride anions

  • Palencia, Cristina
  • Lauwaet, Koen
  • Cueva, Leonor de la
  • Acebrón, M.
  • Conde, Julio J.
  • Meyns, Michaela
  • Klinke, Christian
  • Gallego, José M.
  • Otero, Roberto
  • Juárez, Beatriz H.
Halide ions cap and stabilize colloidal semiconductor nanocrystal (NC) surfaces allowing for NCs surface interactions that may improve the performance of NC thin film devices such as photo-detectors and/or solar cells. Current ways to introduce halide anions as ligands on surfaces of NCs produced by the hot injection method are based on post-synthetic treatments. In this work we explore the possibility to introduce Cl in the NC ligand shell in situ during the NCs synthesis. With this aim, the effect of 1,2-dichloroethane (DCE) in the synthesis of CdSe rod-like NCs produced under different Cd/Se precursor molar ratios has been studied. We report a double role of DCE depending on the Cd/Se precursor molar ratio (either under excess of cadmium or selenium precursor). According to mass spectrometry (ESI-TOF) and nuclear magnetic resonance ( 1H NMR), under excess of Se precursor (Se dissolved in trioctylphosphine, TOP) conditions at 265 °C ethane-1,2- diylbis(trioctylphosphonium)dichloride is released as a product of the reaction between DCE and TOP. According to XPS studies chlorine gets incorporated into the CdSe ligand shell, promoting re-shaping of rod-like NCs into pyramidal ones. In contrast, under excess Cd precursor (CdO) conditions, DCE reacts with the Cd complex releasing chlorine-containing non-active species which do not trigger NCs re-shaping. The amount of chlorine incorporated into the ligand shell can thus be controlled by properly tuning the Cd/Se precursor molar ratio., CP acknowledges financial support from the European Commission under the Seventh Framework Program by means of the grant agreement for the Integrated Infrastructure Initiative N. 262348 European Soft Matter Infrastructure (ESMI). CK and MM acknowledge the Deutsche Forschungsgemeinschaft (DFG) for financial support (KL 1453/5-1). Financial support from the Ministerio de Ciencia e Innovación (FIS2010-18847, FIS2012-33011 and Consolider-Ingenio en Nanociencia Molecular, ref CSD2007-00010), Comunidad de Madrid (grant S2009/MAT-1726) and EU (SMALL, PITN-GA-2009-23884) is gratefully acknowledged. JJC acknowledges Fundación Iberdrola for his scholarship., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Partition of coating agents between nanoparticle interfaces and the polymer in manocomposites

  • Musino, Dafne
  • Oberdisse, Julian
  • Sztucki, Michael
  • Alegría, Ángel
  • Genix, A. C.
Industrial and model polymer nanocomposites are often formulated with coating agents (CAs) to improve polymer–nanoparticle (NP) compatibility. Here, the localization of silane CAs in the styrene–butadiene nanocomposite is investigated through the segmental dynamics of the polymer matrix by broadband dielectric spectroscopy (BDS), allowing the detection of silanes in the matrix through their plasticization effect. This acceleration of dynamics was followed via the shift of τmax of the α-relaxation induced by the presence of CAs of different molecular weights and quantities, for different amounts of incorporated colloidal silica NPs (R ≈ 12.5 nm, polydispersity 12%). Any noteworthy contribution of interfacial polymer layers to τmax has been excluded by reference measurements with bare NPs. Our approach allowed quantifying the partition between the matrix and the NP interfaces and was confirmed independently by calorimetry. As a control parameter, the silane-grafting reaction could be activated or not, which was confirmed by the absence (resp. presence) of partitioning with the matrix. Our main result is that in the first steps of material formulation, before any grafting reaction, CAs both cover the silica surface by adsorption and mix with the polymer matrix—in particular if the latter has chemical compatibility via its functional groups. Silane adsorption was found to be comparable to the grafted amount (1.1 nm–2) and does not increase further, confirming that the plateau of the adsorption isotherm is reached in industrial formulations. These results are hoped to contribute to a better understanding of the surface reactions taking place during complex formulation processes of nanocomposites, namely, the exact amounts at stake, for example, in industrial mixers. Final material properties are affected both through NP-matrix compatibility and plasticization of the latter by unreacted molecules., The authors are thankful for support by the ANR NANODYN project, grant ANR-14-CE22-0001-01 of the French Agence Nationale de la Recherche. They acknowledge financial support from the European Commission under the Seventh Framework Program by means of the grant agreement for the Integrated Infrastructure Initiative no. 262348 European Soft Matter Infrastructure (ESMI)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Dielectric spectroscopy of ionic microgel suspensions

  • Mohanty, P. S.
  • Nöjd, S.
  • Bergman, M. J.
  • Nägele, G.
  • Arrese-Igor, Silvia
  • Alegría, Ángel
  • Roa, R.
  • Schurtenberger, P.
  • Dhont, J. K. G.
The determination of the net charge and size of microgel particles as a function of their concentration, as well as the degree of association of ions to the microgel backbone, has been pursued in earlier studies mainly by scattering and rheology. These methods suffer from contributions due to inter-particle interactions that interfere with the characterization of single-particle properties. Here we introduce dielectric spectroscopy as an alternative experimental method to characterize microgel systems. The advantage of dielectric spectroscopy over other experimental methods is that the polarization due to mobile charges within a microgel particle is only weakly affected by inter-particle interactions. Apart from electrode polarization effects, experimental spectra on PNIPAM-co-AA [poly(N-isopropylacrylamide-co-acrylic acid)] ionic microgel particles suspended in de-ionized water exhibit three well-separated relaxation modes, which are due to the polarization of the mobile charges within the microgel particles, the diffuse double layer around the particles, and the polymer backbone. Expressions for the full frequency dependence of the electrode-polarization contribution to the measured dielectric response are derived, and a theory is proposed for the polarization resulting from the mobile charges within the microgel. Relaxation of the diffuse double layer is modeled within the realm of a cell model. The net charge and the size of the microgel particles are found to be strongly varying with concentration. A very small value of the diffusion coefficient of ions within the microgel is found, due to a large degree of chemical association of protons to the polymer backbone., This work was supported by the Swiss National Science Foundation, the Swedish Research Council (Project 621-2011-4338), the science faculty of Lund University, the European Research Council (ERC-339678-COMPASS), and the Knut and Alice Wallenberg Foundation (project grant KAW 2014.0052). J. K. G. Dhont, G. Nägele, and R. Roa acknowledge support by the German Research Foundation (SFB 985, Functional Microgels and Microgel Systems, Project B6). The authors acknowledge financial support from the European Commission under the Seventh Framework Program by means of the grant agreement for the Integrated Infrastructure Initiative N. 262348, European Soft Matter Infrastructure (ESMI)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Network dynamics in nanofilled polymers

  • Baeza, Guilhem P.
  • Dessi, Claudia
  • Costanzo, Salvatore
  • Zhao, Dan
  • Gong, Shushan
  • Alegría, Ángel
  • Colby, Ralph H.
  • Rubinstein, Michael
  • Vlassopoulos, Dimitris
  • Kumar, Sumit
It is well accepted that adding nanoparticles (NPs) to polymer melts can result in significant property improvements. Here we focus on the causes of mechanical reinforcement and present rheological measurements on favourably interacting mixtures of spherical silica NPs and poly(2-vinylpyridine), complemented by several dynamic and structural probes. While the system dynamics are polymer-like with increased friction for low silica loadings, they turn network-like when the mean face-to-face separation between NPs becomes smaller than the entanglement tube diameter. Gel-like dynamics with a Williams–Landel–Ferry temperature dependence then result. This dependence turns particle dominated, that is, Arrhenius-like, when the silica loading increases to ∼31 vol%, namely, when the average nearest distance between NP faces becomes comparable to the polymer’s Kuhn length. Our results demonstrate that the flow properties of nanocomposites are complex and can be tuned via changes in filler loading, that is, the character of polymer bridges which ‘tie’ NPs together into a network., Partial support has been provided by the EU FP7 (ETN Supolen GA-607937, Infrastructure ESMI GA-262348) and the Greek General Secretariat for Research and Technology (Thalis-380238 COVISCO). M.R. acknowledges financial support from the National Science Foundation under grants DMR-1309892, DMR-1436201 and DMR-1121107, the National Institutes of Health under grants P01-HL108808 and 1UH2HL123645 and the Cystic Fibrosis Foundation. D.Z., S.G., R.H.C. and S.K.K. gratefully acknowledge the National Science Foundation grant DMR-1408323 for financial support., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Role of dynamic asymmetry on the collective dynamics of comblike polymers: Insights from neutron spin-echo experiments and coarse-grained molecular dynamics simulations

  • Arbe, Arantxa
  • Moreno Segurado, Ángel J.
  • Allgaier, Jürgen
  • Ivanova, Oxana
  • Fouquet, Peter
  • Colmenero de León, Juan
  • Richter, Dieter
We investigate the collective dynamics of comblike polymers displaying nanosegregation in side groups and main-chain rich domains, where side groups and backbones are dynamically equivalent. Neutron spin-echo experiments on poly(alkylene oxide)s with increasing side-group length have been focused on the decay of inter- and intradomain correlations and are complemented with molecular dynamics simulations on a coarse-grained model. In general, a good qualitative agreement between simulation and experiment is found. The collective times at inter- and intradomain levels converge with decreasing temperature, implying a common glass transition, and separate at high temperatures, revealing an increasing role of connectivity. The features of collective relaxations—regarding stretching, characteristic time, and temperature dependence—are independent of branching. The standard stretching for side-group motions and the closeness of collective and self-motions show that the anomalies exhibited by dynamically asymmetric comblike macromolecules disappear., The authors acknowledge financial support from the projects MAT2015-63704-P (Spanish-MINECO and EU) and IT-654-13 (Basque Government). This work is partially based on experiments performed at JCNS-instrument J-NSE (Heinz Maier-Leibnitz Zentrum (MLZ), Garching, Germany) and has been supported by the European Commission under the seventh Framework Programme through the “Research Infrastructures” action of the “Capacities” Programme, NMI3-II Grant 283883, and through the grant agreement for the Integrated Infrastructure Initiative N. 262348 European Soft Matter Infrastructure (ESMI)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Self-Assembly and Formation of Chromonic Liquid Crystals from the Dyes Quinaldine Red Acetate and Pyronin Y

  • Magaña, José Rodrigo
  • Homs, Maria
  • Solans, Conxita
  • Obiols-Rabasa, Marc
  • Salonen, Laura M.
  • Rodríguez-Abreu, Carlos
The aqueous self-assembly behavior of the dyes Quinaldine red acetate and Pyronin Y in a wide range of concentrations is reported here for the first time. (1)H NMR spectroscopy, polarized-light optical microscopy, and small and wide X-ray scattering were used to get insight into molecular interactions, phase boundaries and aggregate structure. Quinaldine red acetate and Pyronin Y self-organize into unimolecular stacks driven by attractive aromatic interactions. At high concentrations, spatial correlation among the molecular stacks gives rise to nematic liquid crystals in both systems. Quinaldine red acetate additionally produces a rare chromonic O phase built of columnar aggregates with anisotropic cross-section ordered in a rectangular lattice. The O phase changes into a columnar lamellar structure as a result of a temperature-induced phase transition. Results open the possibility of finding chromonic liquid crystals in other commercially available dyes with a similar molecular structure. This would eventually expand the availability of these unique soft materials and thus introduce new applications for marketed dyes., The authors acknowledge financial support from the European Commission under the Seventh Framework Program by means of the grant agreement for the Integrated Infrastructure Initiative N. 262348 European Soft Matter Infrastructure (ESMI). J.R.M. acknowledges funding from the Ministerio de Economia y Competitividad, Spain (Grant EEBB-I-15-10167 and project CTQ2011-29336-C03-01). C.R.-A. acknowledges funding from EU FP7 Cooperation Program, NMP-theme (Grant no. 314212) and InveNNta project financed by EU Programme for Cross-border Cooperation: Spain-Portugal (POCTEP 2007–2013)., Peer reviewed