Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 6
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Combination of Visualization Techniques for the Analysis of Evaporating Diesel Sprays

  • Payri, Raul|||0000-0001-7428-5510
  • Salvador, Francisco Javier|||0000-0003-3269-2251
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Gil, A.|||0000-0001-7192-6992
[EN] Evaporating diesel sprays from three different multi-hole nozzles have been studied by means of three different and complementary techniques: Mie scattering, double-pass schlieren, and CH radical chemiluminescence. These three kinds of measurements provided valuable information that has allowed us to shed light on the influence of nozzle geometry on the air-fuel mixing and evaporation processes. For this purpose, three six-hole sac nozzles, with different orifice degrees of conicity have been used. These nozzles had been geometrically and hydraulically characterized in a previous publication, where important non-dimensional coefficients describing the nature of the flow have been evaluated. Injection at different pressure conditions has been carried out in an inert environment of gas to study the mixture process, avoiding window fouling by soot deposition from combustion. Studies have been carried out for three different injection pressures and four different gas densities during spray injection, representative of real engine conditions, with changing temperature and pressure in the discharge camera. Liquid-phase penetration and stabilized liquid length for all nozzles and pressure conditions have been determined with the Mie scattering technique. The cylindrical nozzle provided the highest value of the liquid length at a low injection pressure (30 MPa), because of its higher diameter and the absence of cavitation. When the two conical nozzles are compared, no clear differences have been shown between them. Because with this Mie scattering, it is not possible to follow the vapor behavior and considering constraints associated with the geometrical configuration of diesel sprays generated by the multi-hole nozzles, a double-pass schlieren technique has been used for this purpose. The combination of Mie scattering and schlieren allowed for the liquid and vapor phases to be analyzed in terms of penetration. As far as the CH radicals are concerned, these radicals are supposed to appear beyond the position of the stabilized liquid length; however, results show how first CH radical intensity is detected before liquid-phase penetration reaches the stabilized value. When CH radical apparition delays from the start of the injection between all of the nozzles and for all injection conditions are compared, in overall terms, conical nozzles present less delay than cylindrical nozzles. This means that the air-fuel mixing process is more effective in the case of conical nozzles. Thus, the analysis of all of the results made it possible to link the nozzle geometry, fuel-air mixture, spray evaporation, and incipient combustion. © 2012 American Chemical Society., This work was partly sponsored by "Vicerrectorado de Investigacion, Desarrollo e Innovacion" of the "Universitat Politecnica de Valencia" in the frame of Project "Estudio del Flujo en Toberas de Inyeccion Diesel Mediante Tecnicas LES (LESFLOWGRID)", Reference 2837, and "Ministerio de Ciencia e Innovacion" in the frame of Project "Estudio Teorico-Experimental sobre la Influencia del Tipo de Combustible en los Procesos de Atomizacion y Evaporacion del Chorro Diesel (PROFUEL)", Reference TRA2011-26293. This support is gratefully acknowledged by the authors.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Carbon nanoparticles in lateral flow methods to detect genes encoding virulence factors of Shiga toxin-producing Escherichia coli

  • Noguera Murray, Patricia Silvestre|||0000-0001-7155-0710
  • Posthuma-Trumpie, G.A.
  • van Tuil, M.
  • van der Wal, F.J.
  • de Boer, A.
  • Moers, A.P.H.A.
  • van Amerongen, A.
The use of carbon nanoparticles is shown for the detection and identification of different Shiga toxin-producing Escherichia coli virulence factors (vt1, vt2, eae and ehxA) and a 16S control (specific for E. coli) based on the use of lateral flow strips (nucleic acid lateral flow immunoassay, NALFIA). Prior to the detection with NALFIA, a rapid amplification method with tagged primers was applied. In the evaluation of the optimised NALFIA strips, no cross-reactivity was found for any of the antibodies used. The limit of detection was higher than for quantitative PCR (q-PCR), in most cases between 10 4 and 10 5 colony forming units/mL or 0.1-0.9 ng/¿L DNA. NALFIA strips were applied to 48 isolates from cattle faeces, and results were compared to those achieved by q-PCR. E. coli virulence factors identified by NALFIA were in very good agreement with those observed in q-PCR, showing in most cases sensitivity and specificity values of 1.0 and an almost perfect agreement between both methods (kappa coefficient larger than 0.9). The results demonstrate that the screening method developed is reliable, cost-effective and user-friendly, and that the procedure is fast as the total time required is <1 h, which includes amplification. © 2010 The Author(s)., This work was partially supported by the Generalitat Valenciana (BEST/2009/026), the Universidad Politecnica de Valencia (PAID-00-09-2837), and by the Dutch Ministry of Agriculture, Nature and Food Quality (KennisBasis 6 programme). The authors would like to thank Dr. Eva Moller Nielsen at the Danish Veterinary Institute (Copenhagen, Denmark) for providing E. coli control strains and Dr. Lutz Geue (Friedrich-Loeffler-Institut, Wusterhausen, Germany) and Dr. Dorte Dopfer (School of Veterinary Medicine, University of Wisconsin, Madison, WI, USA) for field isolates.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Analysis of diesel spray atomization by means of a near-nozzle field visualization technique

  • Payri, Raul|||0000-0001-7428-5510
  • Salvador, Francisco Javier|||0000-0003-3269-2251
  • Gimeno, Jaime|||0000-0003-3317-9994
  • De La Morena, Joaquín|||0000-0003-0208-508X
[EN] In this paper, a high-resolution visualization technique has been used in order to characterize Diesel spray structure in the near-nozzle field. For this purpose, three conical nozzles with different diameters have been used to relate nozzle geometry and spray behavior in non-cavitating conditions. As a first step, geometrical and hydraulic characterization of the nozzles has been performed. The analysis of the images obtained has shown that spray aperture varied significantly during the first millimeters of the spray, until reaching to the stabilized value of spray cone angle, which is the one usually characterized by other visualization techniques. Furthermore, the structure of the liquid-gas interface presented an oscillatory behavior, which is related to primary atomization process. These oscillations have been quantified and statistically correlated with nozzle geometry and operating conditions by means of three different non-dimensional numbers: Reynolds number, air/fuel density ratio, and Ohnesorge number. © 2011 by Begell House, Inc., This research was sponsored by Vicerrectorado de Investigacion, Desarrollo e Innovacion of the Universitat Politecnica de Valencia, under the Project ` Estudio numerico del flujo en toberas de inyeccion diesel con aproximacion LES y mediante grid computing (LESFLOWGRID), Reference 2837, and by Ministerio de Ciencia e Innovacion, under the Project Estudio teorico experimental sobre la influencia del tipo de combustible en los procesos de atomizacion y evaporacion del chorro Diesel (PROFUEL), Reference No. TRA2011-26293. This support is gratefully acknowledged by the authors.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Carbon nanoparticles as detection labels in antibody microarrays.Detection of genes encoding virulence factors in Shiga toxin-producing Escherichia coli

  • Noguera Murray, Patricia Silvestre|||0000-0001-7155-0710
  • Posthuma-Trumpie, Geertruida A
  • van Tuil, Marc
  • van der Wal, Fimme J.
  • de Boer, Albert
  • Moers, Antoine P. H. A.
  • van Amerongen, Aart
The present study demonstrates that carbon nanoparticles (CNPs) can be used as labels in microarrays. CNPs were used in nucleic acid microarray immunoassays (NAMIAs) for the detection of di¿erent Shiga toxin-producing Escherichia coli (STEC) virulence factors: four genes speci¿c for STEC (vt1,vt2, eae, andehxA) and the gene forE. coli16S (hui). Optimization was performed using a Box Behnken design, andthe limit of detection for each virulence factor was established. Finally,this NAMIA using CNPs was tested with DNA from 48 ¿eld strains originating from cattle feces, and its performance was evaluated by comparing results with those achieved by the reference method q-PCR. All factors tested gave sensitivity and speci¿city values higher than 0.80 and e¿ciency values higher than 0.92. Kappa coe¿cients showed an almost perfect agreement (k > 0.8) between NAMIA and the reference method used forvt1, eae, and ehxA, and a perfect agreement (k = 1) forvt2 and hui. The excellent agreement between the developed NAMIA and q-PCR demonstrates that the proposed analytical procedure is indeed ¿t for purpose, i.e., it is valuable for fast screening of ampli¿ed genetic material such as E. coli virulence factors. This also proves the applicability of CNPs in microarrays., This work was partially supported by the Generalitat Valenciana (BEST/2009/026), the Universidad Politecnica de Valencia (PAID-00-09-2837), and the Dutch Ministry of Agriculture, Nature and Food Quality (Strategic research program Food Safety, Monitoring and Detection KB-06-005). The authors thank Dr. Eva Moller Nielsen at the Danish Veterinary Institute (Copenhagen, Denmark) for providing E. coli control strains and Dr. Lutz Geue (Friedrich-Loeffler-Institut, Wusterhausen, Germany) and Dr. Dorte Dopfer (School of Veterinary Medicine, University of Wisconsin, Madison, WI) for field isolates.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Consequences of using biodiesel on the injection and air-fuel mixing processes in diesel engines

  • Salvador, Francisco Javier|||0000-0003-3269-2251
  • Ruiz-Rosales, Santiago|||0000-0001-9536-3696
  • Salavert Fernández, José Miguel|||0000-0001-8789-5916
  • De La Morena, Joaquín|||0000-0003-0208-508X
A study of the injection process and spray behaviour was made for three different fuels. In particular, blends of rapeseed methyl ester and standard diesel fuel with 5% and 30% biodiesel were used for the current study, as well as pure rapeseed methyl ester. Hydraulic characterization of an eight-hole nozzle was carried out using these three fuels, in order to explore and analyse the influence of the fuel properties on the mass flow rate and the momentum flux at the nozzle exit. Additionally, spray visualization tests were performed in order to obtain information about the spray cone angle, which allows characterization of the air-fuel mixing process. Finally, a theoretical derivation was used to obtain further details of the microscopic characteristics of the spray and to compare the air-fuel mixing efficiencies for the different biodiesel blends., This work was partly supported by Vicerrectorado de Investigacion, Desarrollo e Innovacion of the Universitat Politecnica de Valencia in the framework of the Project Estudio del Flujo en Toberas de Inyeccion Diesel Mediante Tecnicas LES (project no. 2837) and by Ministerio de Ciencia e Innovacion in the framework of the Project Estudio Teorico-experimental sobre la Influencia del Tipo de Combustible en Los Procesos de Atomizacion y Evaporacion del Chorro Diesel (project no. TRA2011-26293).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

A contribution to the understanding of cavitation effects in Diesel injector nozzles through a combined experimental and computational investigation

  • Payri, F.|||0000-0002-3314-4911
  • Payri, Raul|||0000-0001-7428-5510
  • Salvador, Francisco Javier|||0000-0003-3269-2251
  • Martínez López, Jorge
In this paper a combined experimental and computational study was carried out in order to assess the ability of a homogeneous equilibrium model in predicting the experimental behaviour observed from the hydraulical characterization of a nozzle. The nozzle used was a six-orifice microsac nozzle, with cylindrical holes, and therefore inclined to cavitate. The experimental results available for the validation purpose comprised measurements of mass flow rate and spray momentum flux, which correctly combined provide also fundamental information such as discharge coefficient, nozzle exit effective velocity and area contraction. The model was proved to be able of reproducing the experimental results with high degree of confidence and, through the exploration of the internal flow, allowed the explanation of widely reported experimental findings related to cavitation phenomena: the mass flow choking induced by cavitation and the increment of effective injection velocity., This work was partly sponsored by "Vicerrectorado de lnvestigacion, Desarrollo e Innovacion" of the "Universitat Politecnica de Valencia" in the frame of the Project "Estudio del flujo en toberas de inyeccion diesel mediante tecnicas LES (LESFLOWGRID)", Reference No. 2837 and by "Ministerio de Ciencia e Innovacion" in the frame of the Project "Estudio teorico-experimental sobre la influencia del tipo de combustible en los procesos de atomizacion y evaporacion del chorro Diesel (PROFUEL), Reference TRA2011-26293. This support is gratefully acknowledged by the authors.