Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 9
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Continuous monitoring of tip radius during atomic force microscopy imaging

  • Fraxedas, J.
  • Perez Murano, Francesc X.
  • Gramazio, Federico
  • Lorenzoni, Matteo
  • Rull, Enrique
  • Staufer, Urs
Resumen del trabajo presentado al Scanning Microscopies, celebrado en Monterey, California (US) del 29 de septiembre al 1 de octubre de 2015., We present a continuous tip monitoring method during atomic force microscopy imaging based on the use of higher harmonics, which are generated in the repulsive regime as a result of the nonlinear interactions between the cantilever tip and the surface under study. We have applied this method to commercial rectangular microfabricated silicon cantilevers with force constants in the 45 N/m range and fundamental frequencies in the 300-400 kHz range and with tip radii below 10 nm. We have focused in the resonance of the 2nd flexural mode and the 6th harmonic using polystyrene surfaces. The simultaneous acquisition of topographic and higher harmonic images allows a continuous control of the state of the tip. The experimental results have been rationalized with computer simulations taking into account both the cantilever dynamics and the tip-surface interactions., This project is supported by the EC through a grant with contract Nr. 309558 within the 7th Framework Program NMP Call 2012.1.4-3 on Nanoscale mechanical metrology for industrial processes and products. ICN2 acknowledges support of the Spanish MINECO through the Severo Ochoa Centers of Excellence Program under Grant SEV-2013-0295. IMB-CNM, CSIC acknowledges the grant CSD2010-00024., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Otros (Other)

In-situ monitoring of the Atomic Force Microscopy (AFM) tip by analysing the cantilever’s higher harmonic vibrations

  • Rull, Enrique
  • Staufer, Urs
Trabajo presentado a la International MicroNano Conference, celebrada en Amsterdam (Netherlands) del 8 al 9 de diciembre de 2015., Automated in-line Metrology for Nanoscale Production: Aim4np Project. New metrological processes in industry; a challenge in industry., AIM4NP - Automated in-line Metrology for Nanoscale Production (309558); Seventh Framework Programme., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Submodelling simulation of plastic injection for nano roughness replication

  • Pina-Estany, J.
  • Fraxedas, J.
  • Perez Murano, Francesc X.
  • Colominas, C.
  • Puigoriol-Forcada, J. M.
  • García-Granada, A. A.
Póster presentado a la Conferencia Industrial Technologies: "Creating a Smart Europe", celebrada en Amsterdam del 22 al 24 de junio de 2016., Within the www.aim4np.eu project, a metrology platform hosting an Atomic Force Microscope [AFM] will be used for the determination of the nanomechanical properties of surfaces of objects at a production site enabling inline process control., This project has received funding from the European Union’s Seventh Framework Programme for research, technological development and demonstration under Grant agreement No. 309558., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Otros (Other)

Simulation of plastic injection for nano roughness replication

  • Pina-Estany, J.
  • Fraxedas, J.
  • Perez Murano, Francesc X.
  • Colominas, C.
  • Puigoriol-Forcada, J. M.
  • García-Granada, A. A.
Trabajo presentado al Second International Workshop on Software Solutions for Integrated Computational Materials Engineering, celebrado en Barcelona (España) del 12 al 15 de abril de 2016., Within the www.aim4np.eu project, a metrology platform hosting an Atomic Force Microscope [AFM] will be used for the determination of the nanomechanical properties of surfaces of objects at a production site enabling inline process control. Under the nanomechanical properties term we include roughness, adhesion and elasticity. The underlying concept is based on the artificially generated stiffness between the surface to be characterized and the metrology platform using a feedback sensor-actuator system. Plastic injection was chosen as a case system for the validation-study. The goal is to determine the influence of the surface micro/nano roughness of a mould and the performance of the injection moulding process. The determination of the link between the nanomechanical properties of the surface of the mould and the functionality of the mould (that is the surface roughness and defect density of the moulded plastic part) is addressed both by means of experimental and simulation techniques. Moulds and moulded plastic parts have been characterized by AFM and other techniques, and computer models have been developed to simulate the effect of mould surface roughness on the appearance of the final plastic piece. All available simulation codes devoted to plastic injection have so far been conceived for large pieces in industrial applications (e.g. automotive) with critical dimensions well above the millimetre range. Thus, it was foreseeable that the extension of such codes down to the micro- and nanometre range would be challenging, given the used approximations and boundary conditions in the codes. For this reason, the emphasis was initially laid on the experimental part to address the relevant magnitudes of parameters of technical surfaces, such as roughness and morphology. Trying to directly replicate the roughness of the mould surface was a too demanding objective. It was therefore decided to start with the study of well-defined simple patterns in the micrometre-range. Different strategies have been pursued in order to implement available codes to the micro/nanometre range. A first innovative approximation consists in simulating a rough surface by a regular array of semicircles using submodeling. Such an approximation has revealed to be successful and fairly describes the actual morphology of the coated diamond-like carbon films used as protection of the stainless steel surfaces of the moulds. Comparison of Sq roughness values of mould and plastic parts in range 5 to 40 nm are shown in simulation and compared to experiments to conclude that roughness of plastic part is lower than mould part as predicted by simulation., aim4np: Seventh Framework Programme., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Otros (Other)

Simulation of plastic injection for nanostructure pattern replication

  • Pina-Estany, J.
  • Fraxedas, J.
  • Perez Murano, Francesc X.
  • Colominas, C.
  • Puigoriol-Forcada, J. M.
  • García-Granada, A. A.
Trabajo presentado a la International MicroNano Conference, celebrada en Amsterdam (Netherlands) del 8 al 9 de diciembre de 2015, Introduction to aim4np project Plastic injection application of aim4np Plastic injection is selected as a possible application for aim4np to control moulds and plastic parts in-line to assure surface quality. [Aim]: Expand the Fluent solver capacity to the nanoscale and obtain a model correlating mould roughness with part roughness using simulation and experimental results., Aim4np is a FP7 funded project to build an Automated In-line Metrology for (4) Nanoscale Production., Peer reviewed
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Functional dependence of resonant harmonics on nanomechanical parameters in dynamic mode atomic force microscopy

  • Gramazio, Federico
  • Lorenzoni, Matteo|||0000-0001-5287-8761
  • Pérez-Murano, Francesc
  • Rull Trinidad, Enrique
  • Staufer, Urs
  • Fraxedas, Jordi|||0000-0002-2821-4831
We present a combined theoretical and experimental study of the dependence of resonant higher harmonics of rectangular cantilevers of an atomic force microscope (AFM) as a function of relevant parameters such as the cantilever force constant, tip radius and free oscillation amplitude as well as the stiffness of the sample's surface. The simulations reveal a universal functional dependence of the amplitude of the 6th harmonic (in resonance with the 2nd flexural mode) on these parameters, which can be expressed in terms of a gun-shaped function. This analytical expression can be regarded as a practical tool for extracting qualitative information from AFM measurements and it can be extended to any resonant harmonics. The experiments confirm the predicted dependence in the explored 3-45 N/m force constant range and 2-345 GPa sample's stiffness range. For force constants around 25 N/m, the amplitude of the 6th harmonic exhibits the largest sensitivity for ultrasharp tips (tip radius below 10 nm) and polymers (Young's modulus below 20 GPa).
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

A statistical analysis of nanocavities replication applied to injection moulding

  • Pina Estany, Jordi
  • Colominas, Carles
  • Fraxedas, Jordi|||0000-0002-2821-4831
  • Llobet Sixto, Jordi|||0000-0001-7007-9277
  • Pérez Murano, Francesc|||0000-0002-4647-8558
  • Puigoriol-Forcada, Josep Maria
  • Ruso, D.
  • García Granada, Andrés
The purpose of this paper is to investigate both theoretically and experimentally how nanocavities are replicated in the injection moulding manufacturing process. The objective is to obtain a methodology for efficiently replicate nanocavities. From the theoretical point of view, simulations are carried out using a submodeling approach combining Solidworks Plastics for a first macrosimulation and Fluent solver for a subsequent nanosimulation. The effect of the four main factors (melt temperature, mould temperature, filling time and cavity geometry) are quantified using an statistical 2 factorial experiment. It is found that the main effects are the cavity length, the mould temperature and the polymer temperature, with standardized effects of 5, 3 and 2.6, respectively. Filling time has a negative 1.3 standardized effect. From the experimental point of view, Focused Ion Beam technique is used for mechanizing nanocavities in a steel mould. The replication achieved in polycarbonate injection is quantified using an Atomic Force Microscope. It is observed how both the geometry and the position of the cavities in the mould affect its replication.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Replication of nanoscale surface gratings via injection molding

  • Muntada López, Olga
  • Pina Estany, Jordi
  • Colominas, Carles
  • Fraxedas, Jordi|||0000-0002-2821-4831
  • Pérez Murano, Francesc|||0000-0002-4647-8558
  • García Granada, Andrés
Nanostructured gratings fabricated on silicon chips have been successfully transferred to polypropylene plastic parts by means of injection molding. Different sets of experiments were carried out along with a repeatability analysis in order to study the effect in the replication of process parameters such as maximum injection pressure, injection time, charge and polymer temperature, geometric factors such as width and separation between lines of the gratings and flow direction as well as demolding conditions. Among all factors, the one with a larger effect is the separation between consecutive trenches, which was studied in detail through Computational Fluid Dynamics simulations. In addition, a previously not reported sinking effect in the nanostructured area and a shrinking of the pattern period were characterized and simulated.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Quantification of nanomechanical properties of surfaces by higher harmonic monitoring in amplitude modulated AFM imaging

  • Gramazio, Federico
  • Lorenzoni, Matteo|||0000-0001-5287-8761
  • Pérez Murano, Francesc|||0000-0002-4647-8558
  • Evangelio Araujo, Laura
  • Fraxedas, Jordi|||0000-0002-2821-4831
The determination of nanomechanical properties is an intensive topic of study in several fields of nanophysics, from surface and materials science to biology. At the same time, amplitude modulation force microscopy is one of the most established techniques for nanoscale characterization. In this work, we combine these two topics and propose a method able to extract quantitative nanomechanical information from higher harmonic amplitude imaging in atomic force microscopy. With this method it is possible to discriminate between different materials in the stiffness range of 1-3 GPa, in our case thin films of PS-PMMA based block copolymers. We were able to obtain a critical lateral resolution of less than 20 nm and discriminate between materials with less than a 1 GPa difference in modulus. We show that within this stiffness range, reliable values of the Young's moduli can be obtained under usual imaging conditions and with standard dynamic AFM probes.