Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 12
Encontrada(s) 1 página(s)

UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Low-complexity interference variance estimation methods for coded multicarrier systems: application to SFN

  • Caus López, Marius
  • Pérez Neira, Ana Isabel|||0000-0003-4281-3934
  • Renfors, Markku
For single-frequency network (SFN) transmission, the echoes coming from different transmitters are superimposed at the reception, giving rise to a frequency selective channel. Although multicarrier modulations lower the dispersion, the demodulated signal is sensitive to be degraded by inter-symbol interference (ISI) and inter-carrier interference (ICI). In view of this, we use channel coding in conjunction either with filter bank multicarrier (FBMC) modulation or with orthogonal frequency division multiplexing (OFDM). To deal with the loss of orthogonality, we have devised an interference-aware receiver that carries out a soft detection under the assumption that the residual interference plus noise (IN) term is Gaussian-distributed. To keep the complexity low, we propose to estimate the variance of the IN term by resorting to data-aided algorithms. Experimental results show that regardless of the method, FBMC provides a slightly better performance in terms of coded bit error rate than OFDM, while the spectral efficiency is increased when FBMC is considered., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Contribución de congreso (ConferenceOutput)

Experimental performance bounds of MIMO-FBMC/OQAM systems

  • Caus López, Marius
  • Pérez Neira, Ana Isabel|||0000-0003-4281-3934
This paper addresses the application of filter bank multicarrier (FBMC) systems to multiple-input-multiple-output (MIMO) channels. In particular, it is investigated the FBMC modulation based on OQAM, known as FBMC/OQAM. Existing solutions reveal that FBMC/OQAM remains competitive with the orthogonal frequency division multiplexing (OFDM) technique when the number of streams (S), transmit antennas (NT) and receive antennas (NR) are related as follows: S = min(NT,NR). State-of-the-art techniques fail to achieve satisfactory results in FBMC/OQAM systems when S < min(NT,NR). That is because the strongest spatial subchannels exhibit higher gains in MIMO-OFDM than in existing MIMO-FBMC/OQAM systems. To determine if FBMC/OQAM can be successfully applied when strict inequality holds, this paper provides experimental performance bounds, which can be assumed to approximate the optimal performance. In this sense, numerical results show that FBMC/OQAM is able to slightly outperform OFDM when S < min(NT,NR) by attenuating the residual interference 20 dB below the equalized noise. This insightful information could be used in the design process of future techniques to approach the experimental performance bounds.
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Multi-stream transmission for highly frequency selective channels in MIMO-FBMC/OQAM systems

  • Caus López, Marius
  • Pérez Neira, Ana Isabel|||0000-0003-4281-3934
This paper addresses the joint design of MIMO precoding and decoding matrices for filter bank multicarrier (FBMC) systems based on OQAM, known as FBMC/OQAM. Existing solutions that support multi-stream transmission only give satisfactory performance in scenarios with high coherence bandwidth channels. To make progress towards the application of FBMC/OQAM to MIMO channels, we study the design of novel solutions that provide robustness against the channel frequency selectivity and support multi-stream transmission. To this end, two techniques have been devised under the criterion of minimizing the sum mean square error. The non-circular nature of the OQAM symbols has not been ignored, making evident the convenience of performing a widely linear processing. The first technique keeps the complexity at a reasonable level but in exchange the original problem is relaxed yielding a suboptimal solution. With the objective of performing closer to the optimum solution, the second option iteratively computes precoders and equalizers by resorting to an alternating optimization method, which is much more complex. We have demonstrated via simulations that the first technique nearly achieves the same results as the iterative design. Simulation results show that the proposed low-complexity solution outperforms existing MIMO-FBMC/OQAM schemes in terms of bit error rate. As for the comparison with OFDM, the numerical results highlight that FBMC/OQAM remains competitive, with and without perfect channel state information, while it provides spectral efficiency gains. Under highly frequency selective channels the proposed technique significantly outperforms OFDM., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Contribución de congreso (ConferenceOutput)

Low-complexity soft-output MIMO detection in FBMC/OQAM systems

  • Caus, Marius
  • Pérez Neira, Ana Isabel|||0000-0003-4281-3934
  • Lagunas Hernandez, Miguel A.|||0000-0003-3338-244X
This paper focuses on soft-output detection when coded spatial data multiplexing schemes are combined with filter bank multicarrier systems based on the offset quadrature amplitude modulation (FBMC/OQAM). Due to the modulationinduced interference, which is inherent to FBMC/OQAM, the soft-output detection is not trivial. The proposed technique circumvents this problem by removing the interference with reduced complexity. The complexity of the proposed receiver and the system performance are evaluated and compared with the equivalent OFDM one. When the receiver has more antennas than the transmitter, both schemes give similar performance thus, supporting FBMC/OQAM, which presents less complexity., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Characterization of the effects of multi-tap filtering on FBMC/OQAM systems

  • Caus, Marius
  • Pérez Neira, Ana Isabel|||0000-0003-4281-3934
  • Kliks, Adrian
The filter bank multicarrier modulation based on offset quadrature amplitude modulation (FBMC/OQAM) is being considered as an eligible technology for future wireless communications. However, the orthogonality may be destroyed in the presence of multipath fading, and thus, the demodulated data may be affected by inter-symbol and inter-carrier interference. To restore the orthogonality, it is deemed necessary to either precode the symbols to be transmitted or equalize the demodulated data. Under severe propagation conditions, both the precoders and equalizers should perform multi-tap filtering. In this paper, we try to determine whether it is the best choice to combat the channel at the transmit, or at the receive side. The answer to this question is not trivial, since with data precoding, the transmit power may increase, while equalization at the receive side may enhance the noise power. To cast light on this issue, this paper characterizes the average transmit and noise power to determine the influence of multi-tap filtering on the transmit signal power and on the noise variance. The analysis conducted in this paper reveals that if multi-tap precoding yields a power increase, then the noise variance would increase with the same magnitude if the same linear filter was moved from the transmit to the receive side. Therefore, if symbols are properly scaled when the transmit power increases, there is no degradation due to placing the complexity burden at the reception rather than at the transmission. To scale the symbols, it is mandatory to know the additional transmit power. In this sense, a low-complexity method to estimate the power increase is proposed. Simulation-based results confirm that the estimation is reasonably accurate., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Contribución de congreso (ConferenceOutput)

Towards a non-error floor multi-stream beamforming design for FBMC/OQAM

  • Caus, Marius
  • Pérez Neira, Ana Isabel|||0000-0003-4281-3934
  • Cheng, Yao
  • Haardt, Martin
This paper investigates the application of filter bank multicarrier modulation based on the OQAM (FBMC/OQAM) to multiple-input-multiple-output (MIMO) systems. Existing solutions guarantee satisfactory performance when the streams multiplexed on each subcarrier (S) and the number of transmit (NT) and receive (NR) antennas are related as S = min (NT, NR). When S <; min (NT, NR), the techniques presented in previous works either exhibit an error floor or perform much worse than orthogonal frequency division multiplexing (OFDM). To make progress towards the combination of FBMC/OQAM with MIMO we propose a two-step approach and a coordinated beamforming algorithm to design the transmit and the receive processing. Numerical results show that the two-step method provides similar bit error rate (BER) as OFDM when S + 1 = NT = NR. Resorting to the coordinated beamforming solution, which is based on an iterative method, the application of FBMC/OQAM is extended to the general case S <; min (NT, NR). Hence, the techniques presented in this paper demonstrate that FBMC/OQAM can achieve practically the same BER as OFDM with an increased spectral efficiency and a significantly decreased out-of-band radiation, which is an important advantage for non-contiguous spectrum allocations., Peer Reviewed
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Towards a non-error floor multi-stream beamforming design for FBMC/OQAM

  • Caus, Marius
  • Pérez Neira, Ana Isabel
  • Cheng, Yao
  • Haardt, Martin
This paper investigates the application of filter bank multicarrier modulation based on the OQAM (FBMC/OQAM) to multiple-input-multiple-output (MIMO) systems. Existing solutions guarantee satisfactory performance when the streams multiplexed on each subcarrier (S) and the number of transmit (NT) and receive (NR) antennas are related as S = min (NT, NR). When S <; min (NT, NR), the techniques presented in previous works either exhibit an error floor or perform much worse than orthogonal frequency division multiplexing (OFDM). To make progress towards the combination of FBMC/OQAM with MIMO we propose a two-step approach and a coordinated beamforming algorithm to design the transmit and the receive processing. Numerical results show that the two-step method provides similar bit error rate (BER) as OFDM when S + 1 = NT = NR. Resorting to the coordinated beamforming solution, which is based on an iterative method, the application of FBMC/OQAM is extended to the general case S <; min (NT, NR). Hence, the techniques presented in this paper demonstrate that FBMC/OQAM can achieve practically the same BER as OFDM with an increased spectral efficiency and a significantly decreased out-of-band radiation, which is an important advantage for non-contiguous spectrum allocations., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Experimental performance bounds of MIMO-FBMC/OQAM systems

  • Caus López, Marius
  • Pérez Neira, Ana Isabel
This paper addresses the application of filter bank multicarrier (FBMC) systems to multiple-input-multiple-output (MIMO) channels. In particular, it is investigated the FBMC modulation based on OQAM, known as FBMC/OQAM. Existing solutions reveal that FBMC/OQAM remains competitive with the orthogonal frequency division multiplexing (OFDM) technique when the number of streams (S), transmit antennas (NT) and receive antennas (NR) are related as follows: S = min(NT,NR). State-of-the-art techniques fail to achieve satisfactory results in FBMC/OQAM systems when S < min(NT,NR). That is because the strongest spatial subchannels exhibit higher gains in MIMO-OFDM than in existing MIMO-FBMC/OQAM systems. To determine if FBMC/OQAM can be successfully applied when strict inequality holds, this paper provides experimental performance bounds, which can be assumed to approximate the optimal performance. In this sense, numerical results show that FBMC/OQAM is able to slightly outperform OFDM when S < min(NT,NR) by attenuating the residual interference 20 dB below the equalized noise. This insightful information could be used in the design process of future techniques to approach the experimental performance bounds., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Low-complexity interference variance estimation methods for coded multicarrier systems: application to SFN

  • Caus López, Marius
  • Pérez Neira, Ana Isabel
  • Renfors, Markku
For single-frequency network (SFN) transmission, the echoes coming from different transmitters are superimposed at the reception, giving rise to a frequency selective channel. Although multicarrier modulations lower the dispersion, the demodulated signal is sensitive to be degraded by inter-symbol interference (ISI) and inter-carrier interference (ICI). In view of this, we use channel coding in conjunction either with filter bank multicarrier (FBMC) modulation or with orthogonal frequency division multiplexing (OFDM). To deal with the loss of orthogonality, we have devised an interference-aware receiver that carries out a soft detection under the assumption that the residual interference plus noise (IN) term is Gaussian-distributed. To keep the complexity low, we propose to estimate the variance of the IN term by resorting to data-aided algorithms. Experimental results show that regardless of the method, FBMC provides a slightly better performance in terms of coded bit error rate than OFDM, while the spectral efficiency is increased when FBMC is considered., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Low-complexity soft-output MIMO detection in FBMC/OQAM systems

  • Caus, Marius
  • Pérez Neira, Ana Isabel
  • Lagunas Hernandez, Miguel A.
This paper focuses on soft-output detection when coded spatial data multiplexing schemes are combined with filter bank multicarrier systems based on the offset quadrature amplitude modulation (FBMC/OQAM). Due to the modulationinduced interference, which is inherent to FBMC/OQAM, the soft-output detection is not trivial. The proposed technique circumvents this problem by removing the interference with reduced complexity. The complexity of the proposed receiver and the system performance are evaluated and compared with the equivalent OFDM one. When the receiver has more antennas than the transmitter, both schemes give similar performance thus, supporting FBMC/OQAM, which presents less complexity., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Multi-stream transmission for highly frequency selective channels in MIMO-FBMC/OQAM systems

  • Caus López, Marius
  • Pérez Neira, Ana Isabel
This paper addresses the joint design of MIMO precoding and decoding matrices for filter bank multicarrier (FBMC) systems based on OQAM, known as FBMC/OQAM. Existing solutions that support multi-stream transmission only give satisfactory performance in scenarios with high coherence bandwidth channels. To make progress towards the application of FBMC/OQAM to MIMO channels, we study the design of novel solutions that provide robustness against the channel frequency selectivity and support multi-stream transmission. To this end, two techniques have been devised under the criterion of minimizing the sum mean square error. The non-circular nature of the OQAM symbols has not been ignored, making evident the convenience of performing a widely linear processing. The first technique keeps the complexity at a reasonable level but in exchange the original problem is relaxed yielding a suboptimal solution. With the objective of performing closer to the optimum solution, the second option iteratively computes precoders and equalizers by resorting to an alternating optimization method, which is much more complex. We have demonstrated via simulations that the first technique nearly achieves the same results as the iterative design. Simulation results show that the proposed low-complexity solution outperforms existing MIMO-FBMC/OQAM schemes in terms of bit error rate. As for the comparison with OFDM, the numerical results highlight that FBMC/OQAM remains competitive, with and without perfect channel state information, while it provides spectral efficiency gains. Under highly frequency selective channels the proposed technique significantly outperforms OFDM., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Characterization of the effects of multi-tap filtering on FBMC/OQAM systems

  • Caus, Marius
  • Pérez Neira, Ana Isabel
  • Kliks, Adrian
The filter bank multicarrier modulation based on offset quadrature amplitude modulation (FBMC/OQAM) is being considered as an eligible technology for future wireless communications. However, the orthogonality may be destroyed in the presence of multipath fading, and thus, the demodulated data may be affected by inter-symbol and inter-carrier interference. To restore the orthogonality, it is deemed necessary to either precode the symbols to be transmitted or equalize the demodulated data. Under severe propagation conditions, both the precoders and equalizers should perform multi-tap filtering. In this paper, we try to determine whether it is the best choice to combat the channel at the transmit, or at the receive side. The answer to this question is not trivial, since with data precoding, the transmit power may increase, while equalization at the receive side may enhance the noise power. To cast light on this issue, this paper characterizes the average transmit and noise power to determine the influence of multi-tap filtering on the transmit signal power and on the noise variance. The analysis conducted in this paper reveals that if multi-tap precoding yields a power increase, then the noise variance would increase with the same magnitude if the same linear filter was moved from the transmit to the receive side. Therefore, if symbols are properly scaled when the transmit power increases, there is no degradation due to placing the complexity burden at the reception rather than at the transmission. To scale the symbols, it is mandatory to know the additional transmit power. In this sense, a low-complexity method to estimate the power increase is proposed. Simulation-based results confirm that the estimation is reasonably accurate., Peer Reviewed, Postprint (published version)