Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 9
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Kinetic determination of a highly reactive impregnated Fe2O3/Al2O3 oxygen carrier for use in gas-fuelled chemical looping combustion

  • Cabello Flores, Arturo
  • Abad Secades, Alberto
  • García Labiano, Francisco
  • Gayán Sanz, Pilar
  • Diego Poza, Luis F. de
  • Adánez Elorza, Juan
The objective of this work was to determine the kinetic parameters for reduction and oxidation reactions of a highly reactive Fe-based oxygen carrier for use in chemical looping combustion (CLC) of gaseous fuels containing CH4, CO and/or H2, e.g. natural gas, syngas and PSA-off gas. The oxygen carrier was prepared by impregnation of iron on alumina. The effect of both the temperature and gas concentration was analysed in a thermogravimetric analyser (TGA). The grain model with uniform conversion in the particle and reaction in grains following the shrinking core model (SCM) was used for kinetics determination. It was assumed that the reduction reactions were controlled by two different resistances: the reaction rate was controlled by chemical reaction in a first step, whereas the mechanism that controlled the reactions at higher conversion values was diffusion through the product layer around the grains. Furthermore, it was found that the reduction reaction mechanism was based on the interaction of Fe2O3 with Al2O3 in presence of the reacting gases to form FeAl2O4 as the only stable Fe-based phase. The reaction order values found for the reducing gases were 0.25, 0.3 and 0.6 for CH4, H2 and CO, respectively, and the activation energy took values of between 8 kJ mol-1 (for H2) and 66 kJ mol-1 (for CH4). With regard to oxidation kinetics, the reacting model assumed a reaction rate that was only controlled by chemical reaction. Values of 0.9 and 23 kJ mol-1 were found for reaction order and activation energy, respectively. Finally, the solids inventory needed in a CLC system was also estimated by considering kinetic parameters. The total solids inventory in the CLC unit took a minimum value of 150 kg MW-1 for CH4 combustion, which is a low value when compared to those of other Fe-based materials found in the literature., This paper is based on the work carried out within the framework of the SUCCESS project, funded by the European Commission under the seventh Framework Programme (Contract 608571). This research was supported by the Spanish Ministry of Science and Innovation (MICINN Project: ENE2011-26354) and by FEDER., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

The EU-FP7 project SUCCESS – Scale-up of oxygen carrier for Chemical Looping Combustion using environmentally sustainable materials

  • Penthor, Stefan
  • Mattisson, Tobias
  • Adánez Elorza, Juan
  • Bertolin, Stéphane
  • Masi, Enrica
  • Larring, Yngve
  • Langørgeng, Øyvind
  • Ströhleh, Jochen
  • Snijkersi, Frans
  • Geertsi, Lieve
  • Albertsenj, Knuth
  • Williams, Gareth
  • Bertsch, Otmar
  • Authierm, Olivier
  • Dávila, Ytalo
  • Yazdanpanaho, Mahdi
  • Pröll, Tobias
  • Lyngfelt, Anders
  • Hofbauera, Hermann
Work presented at the 13th International Conference on Greenhouse Gas Control Technologies, GHGT-13, 14-18 November 2016, Lausanne, Switzerland, The paper gives a high level overview of the work performed in the EU-FP7 funded project SUCCESS (Scale-up of oxygen carrier for chemical looping combustion using environmentally sustainable materials). The project is the most recent one in a series of successful EU-funded research projects on the chemical looping combustion (CLC) technology. Its main objective is to perform the necessary research in order to demonstrate the CLC technology in the range of 10 MW fuel power input. The main focus is on scale-up of production of two different oxygen carrier materials using large scale equipment and industrially available raw materials. This will guarantee availability of oxygen carrier material at tonne scale. The scale-up of the two materials, a Cu and a Mn based, was successful and first tests with the Cu material have already been performed in four different pilot units up to 150 kW where the material showed excellent performance regarding fuel conversion. In addition to technology scale-up, extensive end-user evaluation is performed. This evaluation includes investigations on health, security and environmental impacts (HSE), a life cycle analysis and a techno-economic analysis to compare the CLC technology for steam generation against the current state-of-the-art technologies., The research leading to these results has received funding from the European Union Seventh Framework Programme (FP7/2007-2013) under grant agreement n° 608571. Financial support is gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Relevance of plant design on CLC process performance using a Cu-based oxygen carrier

  • Abad Secades, Alberto
  • Gayán Sanz, Pilar
  • García Labiano, Francisco
  • Diego Poza, Luis F. de
  • Adánez Elorza, Juan
13 Figures, 4 Tables.-- © 2017. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, Previously validated mathematical CLC models were used to simulate the process performance of CLC methane combustion using an impregnated Cu-based material and to analyse the effect of the fuel reactor design; being either a bubbling fluidized bed or a circulating fluidized bed. The CLC models considered both the fluid dynamic of the fluidized beds at the specific regime and the corresponding kinetics of oxygen carrier reduction. From the model outputs, the performance of the different systems was assessed by calculating the methane conversion in the fuel reactor. Main results highlights that the selection of a suitable particle size of the oxygen carrier and cross section area are key factors to achieve complete combustion with low solids inventory in the fuel reactor. In addition, the growing of bubbles should be limited in order to achieve high CH4 conversion with low solids inventory values, mainly in the bubbling regime with low cross section areas. Complete combustion was predicted with solids inventory in the fuel reactor of 250 kg/MWth (1 m2/MW and particle size of 0.25 mm) or 125 kg/MWth (0.2 m2/MW and a particle size of 0.15 mm) in the bubbling and turbulent regime, respectively. Considering the pressure drop related to these conditions, conclusions for the optimization design of a CLC unit using the Cu-based oxygen carrier are drawn based on the results of the modelling and simulation., This paper was supported by the European Commission Seventh Framework Program under the grant agreement N° 608571 (Project acronym SUCCESS), and by the Spanish Ministry of Economy, Industry and Competitiveness (MINECO Projects: ENE2014-56857-R and ENE2016-77982-R) and the European Union FEDER funds., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Fe2O3–Al2O3 oxygen carrier materials for chemical looping combustion, a redox thermodynamic and thermogravimetric evaluation in the presence of H2S

  • Pishahang, Mehdi
  • Larring, Yngve
  • Adánez Elorza, Juan
  • Gayán Sanz, Pilar
  • Sunding, Martin
9 Figuras, Alumina-supported Fe2O3 oxygen carrier material (OCM) system is among the most promising OCM systems for solid and gaseous fuel CLC. This work utilizes a comprehensive thermogravimetric and thermodynamic equilibrium approach to redox and CLOU performance, oxygen transfer capacity, reduction rate and sulfur tolerance of the Fe2O3 impregnated on Al2O3 OCM. Thermodynamic evaluations reveal that the beneficial composition range lies in a wide range of 7.5–34% molar Fe2O3 ratios. This is the range at which aluminum-rich corundum phase, i.e., (Al, Fe)2O3, remains stable throughout the oxidizing to very reducing oxygen partial pressures in fuel reactor. The experimental system in this study contains 20 mass% Fe2O3, i.e., XFe = 13.8% molar which lies well within this interval. Deep redox cycle experiments confirm the thermodynamic modeling and during the long residence time of this experiment, the sample is almost fully reduced and exhibits its thermodynamic redox oxygen capacity of close to 1.5 mass%. Extension of the deep redox cycles to 15 cycles induces no performance deterioration in terms of capacity, rate of reduction or morphological failure. The redox experiment under sour reducing gas indicates no H2S poisoning for the 20 mass% Fe2O3 supported on Al2O3 OCM. The findings that this system is not affected with the H2S content of the gas, and the prediction of the SO2 release from the fuel reactor is in good agreement with our recent reactor testing findings available in the literature., The work presented in this article is conducted as part of the European Union Seventh Framework Programme (FP7/2007-2013) under Grant Agreement No. 608571 (Project acronym SUCCESS)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Kinetics of CaMn0.775Ti0.125Mg0.1O2.9-δ perovskite prepared at industrial scale and its implication on the performance of chemical looping combustion of methane

  • Abad Secades, Alberto
  • Cabello Flores, Arturo
  • Gayán Sanz, Pilar
  • García Labiano, Francisco
  • Diego Poza, Luis F. de
  • Mendiara, Teresa
  • Adánez Elorza, Juan
17 figures, 6 tables.-- © 2020. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, The reaction kinetics of CaMn0.775Ti0.125Mg0.1O2.9-δ perovskite, prepared at ton-scale to be used as an oxygen carrier in a CLC process with methane, was determined. The variation of the reaction rates, oxygen transport capacity, and oxygen uncoupling behaviour of the selected material with the number of cycles was evaluated in a thermogravimetric analyser. The perovskite was activated for the reduction reaction with all the combustible gases, i.e., H2, CO and CH4. On the contrary, the oxidation rate barely changed throughout the cycles. The oxygen transport capacity underwent a slight decrease during the activation period. Kinetics of reduction, oxidation and oxygen uncoupling reactions were determined for the fresh and activated material assuming a grain model controlled by chemical reaction at low values of solids conversion and diffusion through the product layer at high values of solids conversion. This model predicted correctly the solids conversion vs. time curves as a function of temperature and gas concentration for the oxygen carrier reactions evaluated in this kinetics study. The kinetics data were introduced in a validated mathematical model of a fuel reactor to analyse the amount of solids required to fully combust CH4. A solids inventory of 350 kg/MWth was estimated in the fuel reactor at a temperature of 1243 K. However, this value could be reduced to 160 kg/MWth if the material operates under activation conditions within the CLC unit., This work was partially supported by the project ENE2016-77982-R (AEI/FEDER, UE), ENE2017-89473-R (AEI/FEDER, UE) and the SUCCESS Project, funded by the European Commission under the Seventh Framework Programme (Grant agreement No. 608571 )., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Performance evaluation of a Cu-based oxygen carrier impregnated onto ZrO2 for Chemical-Looping Combustion (CLC)

  • Adánez-Rubio, Iñaki
  • Bararpour, S. Toufigh
  • Abad Secades, Alberto
  • Gayán Sanz, Pilar
  • Williams, Gareth
  • Scullard, Andrew
  • Mahinpey, Nader
  • Adánez Elorza, Juan
11 figures, 3 tables.-- This document is the Accepted Manuscript version of a Published Work that appeared in final form in Industrial and Engineering Chemistry Research, copyright © American Chemical Society after peer review and technical editing by the publisher. To access the final edited and published work see http://dx.doi.org/10.1021/acs.iecr.9b05835, Chemical-looping combustion (CLC) has been introduced as a promising technique with inherent advantages for efficient, low-cost CO2 separation. The type of oxygen carrier employed plays a vital role in improving the overall efficiency and economic penalty of the system. This study investigates the performance of a CuO oxygen carrier impregnated onto ZrO2 in a continuously operated 500 Wth CLC unit over 30 h of CH4 combustion. A decrease in combustion efficiency was observed during the initial 10 h followed by stabilization. A loss of CuO of between 13 and 5 wt % was recorded during the first 5 h of combustion before the CuO content was kept constant. This loss was due to the Cu layer peeling off the surface of particles and the clustering and migration of CuO from internal areas to the surface and then attrited. The effect of the oxygen carrier-to-fuel ratio (ϕ) on the combustion efficiency of the impregnated Cu-based oxygen carrier was studied. In order to reach a combustion efficiency of 99%, ϕ values of 3.9 were needed. The particle attrition rate was stabilized after 30 h of operation at 0.06%/h, and the estimated lifetime was 1500 h of operation. XRD and TPR analyses confirmed very low interaction between CuO and the support (ZrO2), which was unable to retain CuO inside the particles. Therefore, the lack of interaction between CuO and the ZrO2 support is not positive for oxygen carrier behavior in the CLC process., The work presented in this article is partially funded by the Spanish Research Council (CSIC) through the Intramural Project (201980E043) and by the European Commission Seventh Framework Programme under Grant 608571 (Project acronym SUCCESS). S. Toufigh Bararpour is grateful to Mitacs Globalink Research for the award received (Mitacs Globalink Research Award IT13491 for students studying in Canadian universities)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Modelling Chemical Looping Combustion of natural gas: simulation, validation and optimization

  • Abad Secades, Alberto
  • Diego Poza, Luis F. de
  • Gayán Sanz, Pilar
  • Adánez Elorza, Juan
Poster presented at the 5th International Conference on Chemical Looping, September 24th - 27th, 2018, The Chateaux, Park City, Utah, USA, The objective of this work was to determine suitable design parameters NORWAY and operating conditions for the complete combustion of CH4 with the impregnated Cu-based oxygen carrier developed by ICB-CSIC., This work has been supported by the Seventh Framework Program (EU) under grant agreement No. 608571 (Project acronym SUCCESS) and by the Regional Aragon Government via the T05_17R research group funding., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Increasing energy efficiency in chemical looping combustion of methane by in-situ activation of perovskite-based oxygen carriers

  • Cabello Flores, Arturo
  • Abad Secades, Alberto
  • Gayán Sanz, Pilar
  • García Labiano, Francisco
  • Diego Poza, Luis F. de
  • Adánez Elorza, Juan
12 figures, 3 tables.-- © 2021. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, CaMnO3-based perovskites are attractive for use as oxygen carriers in chemical looping combustion (CLC) because they are made from cheap materials (manganese, calcium). However, these materials show low reactivity with methane, and high oxygen carrier-to-fuel ratios (ϕ) are required to achieve complete fuel combustion. It is believed that energy efficiency in the chemical looping process would be improved if the reactivity of these materials were higher. In this work, the increase in reactivity of a perovskite (CaMn0.775Mg0.1Ti0.125O2.9-δ) material is evaluated during its in-situ activation under determined operating conditions in a 0.5 kWth CLC pilot plant. The combustion efficiency of methane over 60 h of continuous operation was analysed taking into consideration the effect of operating conditions on the activation process for increasing the reactivity of the perovskite. The material increased in reactivity as the ϕ ratio decreased to below 6, improving combustion efficiency. Moreover, the material was pre-activated by being fully reduced in the CLC plant. The conversion of methane with the pre-activated material was subsequently higher than the conversion achieved before the activation process, and almost complete combustion was achieved at a lower ϕ ratio. Characterization of the particles after the combustion tests showed good stability of the material with the operating time, although a negative effect on the crushing strength was observed when the particles were highly reduced. The impact of the perovskite material activation on the energy efficiency of the process is discussed., This work was partially supported by the SWINELOOP project (PID2019-106441RB-I00/AEI/10.13039/501100011033) and the SUCCESS Project, funded by the European Commission under the Seventh Framework Programme (Grant agreement No. 608571). J. Adánez thanks CSIC for the financial support given to the project 201980E043., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Sulfur interaction and regeneration of CaMn0.775Ti0.125Mg0.1O2.9−δ perovskite as oxygen carrier during combustion of sour gas in a 500 Wth chemical looping combustion unit

  • Cabello Flores, Arturo
  • Abad Secades, Alberto
  • Mendiara, Teresa
  • Obras-Loscertales, Margarita de las
  • Diego Poza, Luis F. de
12 figures, 3 tables., In the present study, the performance of a CaMn0.775Ti0.125Mg0.1O2.9−δ perovskite used as an oxygen carrier to burn sour gas with different H2S concentrations (up to 3000 vppm) in a continuous 500 Wth chemical looping combustion (CLC) prototype was investigated. After 29 h of sour gas combustion, the combustion efficiency had dropped by 18% in comparison with the reference test without sulfur addition. The characterization of the used particles of the perovskite confirmed that the presence of sulfur in the fuel gas had a poisonous effect through the formation of undesired compounds, such as CaSO4. The reactivity with CH4 and oxygen uncoupling capacity decreased, which could explain the decrease in the combustion efficiency. Two regeneration processes, one at high temperature (1273 K) and another one at low temperature (773–873 K), were carried out in a batch fluidized bed reactor to remove the amount of sulfur accumulated in the oxygen carrier particles. The detection of appreciable amounts of gaseous sulfur-based compounds (SO2 and H2S) during the experimentation and the postcharacterization results obtained through different techniques such as X-ray diffraction, ultimate analysis, and thermogravimetric analysis confirmed the effectiveness of both processes. Finally, the feasibility of implementation of the regeneration processes in a commercial CLC unit was thoroughly analyzed., This work was partially supported by the SWINELOOP Project (PID2019-106441RB-I00/AEI/10.13039/501100011033) and the SUCCESS Project, funded by the European Commission under the Seventh Framework Programme (Grant Agreement No. 608571). A. Cabello is also grateful for Grant IJC2019-038908-I funded by MCIN/AEI/10.13039/501100011033., Peer reviewed