Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 20
Encontrada(s) 1 página(s)

e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publication Artículo científico (JournalArticle)

Pressurized pyrolysis of mattress residue: An alternative to landfill management

  • Serrano García, Daniel
  • Horvat, Alen
  • Mata, Ricardo M.
  • Costa, Paula
  • Paraleda, Filipe
Mattresses are a difficult waste to manage in landfills due to their large volume and low density. Pyrolysis treatment could reduce its volume while producing fuel or products valuable for the chemical industry. Pressurized pyrolysis at 400, 450, and 500 °C is carried out in a lab-scale autoclave at initial pressures 4.2, 8.4, and 16.8 bar. Product gas yield increases slightly along with elevated pressure as well as temperature. However, beyond 8.4 bar the initial pressure makes no discernible differences. CO and CO2 are the major gas species followed by CH4. CO contributes the most to the product gas energy content followed by C3 species, C2H6, and H2. Calculated energy content (heating value) is between 2 and 15 MJ·Nm¿3. In terms of product gas energy content, low pressure pyrolysis is favorable over high pressure pyrolysis. According to integration areas of chromatographic measurements the liquid phase contains up to 25 % of N-compounds, with benzonitrile being the most abundant, followed by toluene, o-xylene, and ethylbenzene. The solid char maintains constant properties across operating conditions, with carbon and energy contents of approximately 75 wt% and 30 MJ·kg−1, respectively., This research has received funding from the European Union's Horizon 2020 research and innovation programme under grant agreement No 731101 (BRISK II project: Biofuels Research Infrastructure for Sharing Knowledge II). Funding for APC: Universidad Carlos III de Madrid (Read & Publish Agreement CRUE-CSIC 2023).
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publication Artículo científico (JournalArticle)

Multi-scale modelling of fluidized bed biomass gasification using a 1D particle model coupled to CFD

  • Von Berg, Lukas
  • Anca-Couce, Andrés
  • Hochenauer, Christoph
  • Scharler, Robert
For many fluidized bed applications, the particle movement inside the reactor is accompanied by reactions at the particle scale. The current study presents for the first time in literature a multi-scale modelling approach coupling a one-dimensional volumetric particle model with the dense discrete phase model (DDPM) of ANSYS Fluent via user defined functions. To validate the developed modelling approach, the current study uses experimental data of pressure drop, temperature and gas composition obtained with a lab-scale bubbling fluidized bed biomass gasifier. Therefore, a particle model developed previously for pyrolysis was modified implementing a heat transfer model valid for fluidized bed conditions as well as kinetics for char gasification taken from literature. The kinetic theory of granular flow is used to describe particle¿particle interactions allowing for feasible calculation times at the reactor level whereas an optimized solver is employed to guarantee a fast solution at the particle level. A newly developed initialization routine uses an initial bed of reacting particles at different states of conversion calculated previously with a standalone version of the particle model. This allows to start the simulation at conditions very close to stable operation of the reactor. A coupled multi-scale simulation of over 30 s of process time employing 300.000 inert bed parcels and about 25.000 reacting fuel parcels showed good agreement with experimental data at a feasible calculation time. Furthermore, the developed approach allows for an in-depth analysis of the processes inside the reactor allowing to track individual reacting particles while resolving gradients inside the particle., This project has received funding from European Union's Horizon 2020 Research and Innovation Programme under grant agreement number 731101 (BRISK II). Furthermore, the financial support of the COMET Module project BIO-LOOP (Austrian Research Promotion Agency - FFG - Project Number 872189) funded by the federal government of Austria and the federal province Styria is gratefully acknowledged. The authors want to thank Mario Blehrmühlhuber for conducting cold-flow simulations and evaluating the applicability of the DDPM for the developed model. We further want to thank Markus Braun for his helpful hints when using the DDPM and Simon Schneiderbauer for his advice regarding the coupling strategy., Publicado
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publication Artículo científico (JournalArticle)

Evaluation of heat transfer models at various fluidization velocities for biomass pyrolysis conducted in a bubbling fluidized bed

  • Von Berg, Lukas
  • Soria Verdugo, Antonio
  • Hochenauer, Christoph
  • Scharler, Robert
  • Anca-Couce, Andrés
Four different models for heat transfer to the particles immersed in a fluidized bed were evaluated and implemented into an existing single particle model. Pyrolysis experiments have been conducted using a fluidized bed installed on a balance at different temperatures and fluidization velocities using softwood pellets. Using a heat transfer model applicable for fluidized beds, the single particle model was able to predict the experimental results of mass loss obtained in this study as well as experimental data from literature with a reasonable accuracy. A good agreement between experimental and modeling results was found for different reactor temperatures and configurations as well as different biomass types, particle sizes ¿ in the typical range of pellets - and fluidization velocities when they were higher than U/Umf=1.5. However, significant deviations were found for fluidization velocities close to minimum fluidization. Heat transfer models which consider the influence of fluidization velocity show a better agreement in this case although differences are still present., This project has received funding from European Union's Horizon 2020 Research and Innovation Programmeunder grant agreement number 731101 (BRISK II).
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publication Artículo científico (JournalArticle)

Challenges in kinetic parameter determination for wheat straw pyrolysis

  • Fonseca, Frederico G.
  • Anca-Couce, Andrés
  • Funke, Axel
  • Dahmen, Nicolaus
This article belongs to the Topic New Advances in Waste and Biomass Valorization, Second-derivative (DDTG) curves helped overcome the challenges of overlapping peaks in the DTG curves of wheat straw; Deconvolution methods lead to high errors in the estimation of lignin content; Curve-fitting methods lead to lower errors when determining the kinetics of biomass degradation, especially for hemicellulose; Reaction networks were modified to consider K content to describe straw pyrolysis. Highlights: Wheat straw is a renewable agricultural by-product that is currently underutilized in the production of bioenergy and bioproducts due to its high ash content, as well as high transport costs due to its low volumetric energy density. The thermogravimetric analysis of this material produces derivative curves with a single broad peak, making it difficult to identify the three conventional pseudo-components (cellulose, hemicellulose, and lignin), which is resolved using the second derivative to determine inflection points. Model-fitting methods and isoconversional methods were applied to determine the degradation kinetics of wheat straw at two different particle sizes, as well as that of a reference feedstock (beech wood), and the obtained values were used to divide the degradation curves to be compared to the experimental data. Seven different pyrolysis reaction networks from the literature were given a similar treatment to determine which provides the best estimation of the actual pyrolysis process for the case of the feedstocks under study. The impact of the potassium content in the feedstock was considered by comparing the original pathway with a modification dependent on the experimental potassium content and an estimated optimum value., This work has received funding from the European Union's Horizon 2020's research and innovation programme under grant agreement number 731101.
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publication Artículo científico (JournalArticle)

Correlations between tar content and permanent gases as well as reactor temperature in a lab-scale fluidized bed biomass gasifier applying different feedstock and operating conditions

  • Von Berg, Lukas
  • Pongratz, Gernot
  • Pilatov, Aleksandr
  • Almuina Villar, Hernán
  • Hochenauer, Christoph
  • Scharler, Robert
  • Anca-Couce, Andrés
The major problem of fluidized bed biomass gasification is the high tar contamination of the producer gas which is associated with the complex and time-consuming sampling and analysis of these tars. Therefore, correlations to predict the tar content are a helpful tool for the development and operation of biomass gasifiers. Correlations between tars and gas composition as well as reactor temperature derived for a steam-blown lab-scale bubbling fluidized bed gasifier are investigated in this study to assess their applicability. A comprehensive data set containing over 80 experimental points was obtained for various operation conditions, including variations in temperature from 700 to 800 °C, feedstock, amount of steam for fluidization, as well as the addition of oxygen. Linear correlations between tar and permanent gases show good accuracy for H2 and CH4 when using pure steam. However, experiments conducted with steam-oxygen mixtures show high deviations for the CH4-based correlation and smaller but still significant deviations for the H2-based correlation. No relation between tar and CO or CO2 was found. The correlation between tar and temperature shows highest accuracy, including good agreement with the steam-oxygen experiments. All tar correlations showed useful results over a broad operating range. However, significant deviations can be obtained when considering just one gas compound. Therefore, a combination of different correlations considering gas components and temperature seems to be the best method of tar prediction. This leads to a powerful tool for fast online tar monitoring for a broad range of operating conditions, once a calibration measurement was conducted., Acknowledgements This project has received funding from European Union’s Horizon 2020 Research and Innovation Programme under grant agreement number 731101 (BRISK II).
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publication Artículo científico (JournalArticle)

Release of N-containing compounds during pyrolysis of milk/dairy processing sludge - Experimental results and comparison of measurement techniques

  • Kwapinska, Marzena
  • Sommersacher, Peter
  • Kienzl, Norbert
  • Retschitzegger, Stefan
  • Lagler, Jacqueline
  • Horvat, Alen
  • Leahy, James J.
Kwapinska, M., Sommersacher, P., Kienzl, N., Retschitzegger, S., Lagler, J., Horvat, A., & Leahy, J. J. (2024). Corrigendum to “Release of N-containing compounds during pyrolysis of milk/dairy processing sludge – Experimental results and comparison of measurement techniques” [J. Anal. Appl. Pyrolysis 178 (2024) 106391]. Journal of Analytical and Applied Pyrolysis, 178(106423). https://doi.org/10.1016/j.jaap.2024.106423 Kwapinska, M., Sommersacher, P., Kienzl, N., Retschitzegger, S., Lagler, J., Horvat, A., & Leahy, J. J. (2024). WITHDRAWN: Corrigendum to “Release of N-containing compounds during pyrolysis of milk/dairy processing sludge – Experimental results and comparison of measurement techniques” [J Anal Appl Pyrolysis 178 (2024) 106391]. Journal of Analytical and Applied Pyrolysis, 180(106462). https://doi.org/10.1016/j.jaap.2024.106462, A dried dairy processing sludge (sludge from wastewater treatment of an effluent from a milk processing plant) was pyrolysed in a single-particle reactor at different temperatures from 400 °C to 900 °C. NH3 and HCN were measured online and offline by means of FTIR as well as by cumulative sampling in impinger bottles (in 0.05 M H2SO4 and 1 M NaOH, respectively) and analysed by photometric method. NO and NO2 were measured online using a nitric oxide analyser while N2O was measured by FTIR. Nitrogen (N) in the sludge and in the remaining char, char-N, was determined. Moreover, tar content in pyrolysis gas was measured and tar-N was determined. The results with respect to N mass balance closure are discussed. The different measurements techniques are compared. For pyrolysis at 520 ℃ and 700 ℃ nitrogen in the gas phase was mainly contained as N2 (36 % and 40 % respectively), followed by NH3 (15 % and 18 %), tar-N (10 % and 9 %), HCN (1 % and 3 %), NO (1 %) and NO2 (0.2 %). The dairy processing sludge has very specific properties with organic-N present predominantly as proteins and a high content of inherent Ca. These characteristics affected the distribution of N. The amount of char-N was higher while the amount of tar-N lower than for sewage sludge from literature, at comparable pyrolysis temperature., The authors would like to acknowledge the the European Union’s Horizon2020’s research and innovation programme for the financial support of the experimental campaign through the BRISK2 project (grant agreement number 731101). Experiments were carried out at BEST- Bioenergy and Sustainable Technologies in Graz (Austria). This work was also supported by Enterprise Ireland through its Technology Centre programme - Grant no TC/2016/0016
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publication Artículo científico (JournalArticle)

Multi-stage model for the release of potassium in single particle biomass combustion

  • Anca-Couce, Andrés
  • Sommersacher, Peter
  • Hochenauer, Christoph
  • Scharler, Robert
The release of potassium during biomass combustion leads to several problems as the emissions of particle matter or formation of deposits. K release is mainly described in literature in a qualitative way and this work aims to develop a simplified model to quantitatively describe it at different stages. The proposed model has 4 reactions and 5 solid species, describing K release in 3 steps; during pyrolysis, KCl evaporation and carbonate dissociation. This release model is coupled into a single particle model and successfully validated with experiments conducted in a single particle reactor with spruce, straw and Miscanthus pellets at different temperatures. The model employs same kinetic parameters for the reactions in all cases, while different product compositions of the reactions are employed for each fuel, which is attributed to differences in composition. The proposed model correctly predicts the online release at different stages during conversion as well as the final release for each case., The financial support of the Austrian Federal Government's Climate and Energy Fund (Klima- und Energiefonds) for the Grate Advance Project (FFG number 852048) within the framework of the 9th Joint Call of ERANET Bioenergy and the Multi Fuel Low Emission project (FFG number 858771) within the 3rd call of the Energy Research Program as well of the European Union's Horizon 2020 Research and Innovation Programme under grant agreement number 731101 (BRISK II) are gratefully acknowledged.
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publication Artículo científico (JournalArticle)

Assessment of measurement methods to characterize the producer gas from biomass gasification with steam in a fluidized bed

  • Anca-Couce, Andrés
  • Von Berg, Lukas
  • Pongratz, Gernot
  • Scharler, Robert
  • Hochenauer, Christoph
  • Geusebroek, Marco
  • Kuipers, Johan
  • Mourao Vilela, Carlos
  • Kraia, Tzouliana
  • Panopoulos, Kyriakos
  • Funcia, Ibai
  • Dieguez Alonso, Alba
  • Almuina Villar, Hernan
  • Tsiotsias, Timotheos
  • Kienzl, Norbert
  • Martini, Stefan
Measuring the producer gas from biomass gasification is very challenging and the use of several methods is required to achieve a complete characterization. Various techniques are available for these measurements, offering very different affordability or time demand requirements and the reliability of these techniques is often unknown. In this work an assessment of commonly employed measuring methods is conducted with a round robin. The main permanent gases, light hydrocarbons, tars, sulfur and nitrogen compounds were measured by several partners employing a producer gas obtained from fluidized bed gasification of wood and miscanthus with steam. Online and offline methods were used for this purpose and their accuracy, repeatability and reproducibility are here discussed. The results demonstrate the reliability of gas chromatography for measuring the main permanent gases, light hydrocarbons, benzene and H2S, validating the obtained results with other methods. An online method could also measure NH3 with a reasonable accuracy, but deviations were present for compounds at even lower concentrations. Regarding tar sampling and analysis, the main source of variability in the results was the analysis of the liquid samples, especially for heavier compounds. The presented work pointed out the need for a complementary use of several techniques to achieve a complete characterization of the producer gas from biomass gasification, and the suitability of certain online techniques as well as their limitations., The financial support of the European Union's Horizon 2020 Research and Innovation Programme under grant agreement number 731101 (BRISK II) is gratefully acknowledged.
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publication Artículo científico (JournalArticle)

Production and characterization of bio-oil from fluidized bed pyrolysis of olive stones, pinewood, and torrefied feedstock

  • Trubetskaya, Anna
  • Von Berg, Lukas
  • Johnson, Robert
  • Moore, Sean
  • Leahy, J. J.
  • Han, Yinglei
  • Lange, Heiko
  • Anca-Couce, Andrés
Advancements in fluidized bed pyrolysis mechanisms and analytical methodologies are critical for progress in the biorefinery sector in general and the aviation fuel sector in particular. The statistical modelling of pyrolysis product yields and composition allowed us to observe advantages of operating temperature and feedstock selections over the torrefaction process and catalyst addition in a fluidized bed reactor. Results suggest that the chemical composition and physical properties of bio-oil from pyrolysis of olive stones at 600 degrees C and pinewood pellets at 500 degrees C are the most suitable for use as fuels. This work suggests that only combined use of selected gas chromatography mass spectroscopy, UV fluorescence, nuclear magnetic resonance spectroscopy, and rheology can provide comprehensive information on pyrolysis bio-oil composition. Importantly from a technological point of view, bio-oil was characterized i) by a viscosity similar to that of fossil-based oil; ii) by a low oxygen and water content; and iii) by a balanced composition of aliphatic and aromatic species. These factors indicate that bio-oil from fluidized bed pyrolysis of biomasses is a promising material for use in the aviation industry and energy production., The authors gratefully acknowledge financial support from Science Foundation Ireland (Grant number 16/SP/3829) and Arigna Fuels under the Sustainable Energy and Fuel Efficiency (SEFE) spoke of the Research Centre for Marine and Renewable Energy (MaREI). The authors gratefully acknowledge financial support (Grant number 731101) given by European Union's Horizon 2020 Research and Innovation Programme (BRISK II). Dr. Gerrit Ralf Surup from NTNU is acknowledged for technical support on Karl Fisher titration and elemental analysis.
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publication Artículo científico (JournalArticle)

Experimental investigation of poultry litter gasification and co-gasification with beech wood in a bubbling fluidised bed reactor - Effect of equivalence ratio on process performance and tar evolution

  • Katsaros, Giannis
  • Pandey, Daya Shankar
  • Horvat, Alen
  • Aranda Almansa, Guadalupe
  • Fryda, Lydia E.
  • Leahy, James J.
  • Tassou, Savvas A.
The effect of equivalence ratio on gasification of poultry litter, blend of poultry litter with beech wood and beech wood alone, was experimentally studied in a lab-scale fluidised bed reactor. Lower calorific value decreased with equivalence ratio whereas carbon conversion efficiency revealed the opposite trend. Beech wood showed both the highest lower calorific value and carbon conversion efficiency, 4.96 MJ/m3 and 91.6% respectively. Total gas chromatography-detectable tar decreased with an increase in equivalence ratio. The reduction in total gas chromatography-detectable tar was more profound in the case of poultry litter (22%). Beech wood illustrated the highest amount of total gas chromatography-detectable tar, 7.52gtar/kgfeedstock-daf at the lowest equivalence ratio, due to the higher lignin content responsible for generation of polycyclic aromatic hydrocarbons. Agglomeration occurred while gasifying poultry litter at 750°C and at the highest equivalence ratio (0.25), whereas in the case of blend and beech wood alone all the test runs were conducted successfully., The authors would like to express their gratitude and appreciation to the European Commission for the financial support of the experimental campaign through the BRISK2 project (grant agreement number 731101) and to the staff of the Energy Research Centre of the Netherlands (ECN part of TNO) for hosting the experimental campaign. This work is supported by the Engineering and Physical Sciences Research Council (EPSRC, EP/P004636/1, UK). The financial support from EPSRC is gratefully acknowledged. Daya Shankar Pandey acknowledges funding from the Global Challenges Research Fund (GCRF, R5004, UK).
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publication Reseña (Review)

Bioenergy technologies, uses, market and future trends with Austria as a case study

  • Anca-Couce, Andrés
  • Hochenauer, Christoph
  • Scharler, Robert
The current bioenergy uses and conversion technologies as well as future trends for the production of heat, power, fuels and chemicals from biomass are reviewed. The focus is placed in Austria, which is selected due to its high bioenergy utilization, providing 18.4% of the gross energy final consumption in 2017, and its strong industrial and scientific position in the field. The most common bioenergy application in Austria is bioheat with 170 PJ in 2017 mainly obtained from woody biomass combustion, followed by biofuels with 21 PJ and bioelectricity with 17 PJ. Bioheat has a stable market, where Austrian manufacturers of boilers and stoves have a strong position exporting most of their production. Future developments in bioheat production should go in the line of further reducing emissions, increasing feedstock flexibility and coupling with other renewables. For bioelectricity and biofuels, the current framework does not promote the growth of the current main technologies, i.e. combined heat and power (CHP) based on biomass combustion or biogas and first generation biofuels. However, an increase in all bioenergy uses is required to achieve the Austrian plan to be climate neutral in 2040. The current initiatives and future possibilities to achieve this increase are presented and discussed, e.g. mandatory substitution of old oil boilers, production of biomethane and early commercialization of CHP with a high efficiency or demonstration of advanced biofuels production based on gasification., Funding received from European Union's Horizon 2020 Research and Innovation Programme under grant agreement number 731101 (BRISK II) is gratefully acknowledged.
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publication Artículo científico (JournalArticle)

Effect of bed material density on the performance of steam gasification of biomass in bubbling fluidized beds

  • Soria Verdugo, Antonio
  • Von Berg, Lukas
  • Serrano García, Daniel
  • Hochenauer, Christoph
  • Scharler, Robert
  • Anca-Couce, Andrés
Steam gasification of lignocellulosic biomass in a bubbling fluidized bed reactor was analyzed by means of the composition of the producer gas, including tars, and temperature distribution in the reactor. The catalytic and sorbent effect of sepiolite particles was studied by comparison of the tars generated with those produced in a bed of olivine, widely used in biomass gasification applications. Sepiolite has a lower particle density, which influences the forces acting on fuel and char particles and leads to a more homogeneous distribution of them in the dense bed during the gasification process. Fluidized beds of sepiolite particles contribute to increase the heating value of the producer gas and its hydrogen content compared to gasification under the same operating conditions in olivine beds. Furthermore, the tar yield is around 25% lower when gasifying in sepiolite beds, reducing the requirement of secondary methods for tars removal. Long-term gasification tests were also conducted in a sepiolite bed to evaluate the mitigation of the sorbent/catalytic effect of sepiolite with time., This project has received funding from European Union’s Horizon 2020 Research and Innovation Programme under grant agreement number 731101 (BRISK II).
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publication Artículo científico (JournalArticle)

Pollutant emissions released during sewage sludge combustion in a bubbling fluidized bed reactor

  • Soria Verdugo, Antonio
  • Kauppinen, Juho
  • Soini, Teemu
  • García Gutiérrez, Luis Miguel
  • Pikkarainen, Toni
The combustion of dry sewage sludge particles in a bubbling fluidized bed was studied in detail, analyzing the composition of the exhaust gases by means of a FTIR equipment. The operating conditions of the fluidized bed, i.e., the bed temperature and mass flow rate of fluidizing air, were varied to quantify their effect on the exhaust gas composition. The bed material was also varied, using sepiolite, silica sand and braunite particles, to evaluate the effect of different bed densities on the pollutant emissions. The results obtained for the combustion of sewage sludge particles in the different fluidized beds tested were compared to combustion tests run for the same operating conditions and bed materials using Cynara cardunculus L. as a fuel. Pollutant emissions derived from sludge combustion are much higher than those obtained from combustion of Cynara. The operating conditions also affect the emissions, e.g., the concentration of CO in the exhaust fumes decreased substantially when increasing bed temperature and air flow rate. The bed density has an effect on the combustion efficiency of sludge, obtaining higher efficiencies in low-density beds for high temperature and air flow rates, while the efficiency was increased in high-density beds for low bed temperature and fluidizing air flow rate. The effects of ash accumulation and agglomerates formation were also analyzed., This project has received funding from European Union's Horizon 2020 Research and Innovation Program under grant agreement number 731101 (BRISK II).
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publication Artículo científico (JournalArticle)

Waste tyres valorisation through gasification in a bubbling fluidised bed: An exhaustive gas composition analysis

  • Serrano García, Daniel
  • Horvat, Alen
  • Batuecas Fernández, Esperanza
  • Abelha, Pedro
Waste tyres gasification in a bubbling fluidised bed reactor is evaluated by means of a complete characterisation of the product gas. The experiments are carried out at two temperatures, 700 and 850 degrees C, and various equivalence ratios (ER) while using air as a gasifying. Additionally, the effect of steam is also studied at 850 degrees C. High temperature and low ER increase the production of H2, CH4, and C2H4. Steam addition mainly affects H2 and CO production. Low carbon conversion (CC) into gas and cold gas efficiency (CGE) are obtained, increasing with temperature and ER. The lower heating value (LHV) of the gas decreases with the ER because of the higher partial combustion rates. LHV values range between 12 MJ/Nm3 with steam addition at ER = 0.13 and 850 degrees C to 5.3 MJ/Nm3 at ER = 0.33 and 700 degrees C using air only. Along with a major permanent gas (CO2, CO, H2, CH4, and C2Hn), up to 25 short-chain hydrocarbons (non-aromatic hydrocarbons ranging from C3 to C6+) and two light aromatics are present in the product gas. Among short-chain hydrocarbons, C3 and C4 compounds are present in the highest yields. All these minor hydrocarbon species (i.e., C3 to C6+), not usually reported in biomass or waste gasification studies, yield up to 13 %vol. on a N2-free basis. Their contribution to the gasification performance is important because they account for half of the energy content in the product gas. Therefore, it is important to consider them in the gasification process, not only for energy purposes but also for the chemical industry., This research has received funding from the European Union's Horizon 2020 research and innovation programme under grant agreement No 731101 (BRISK II project: Biofuels Research Infrastructure for Sharing Knowledge II). Funding for APC: Universidad Carlos III de Madrid (Read & Publish Agreement CRUE-CSIC 2022).
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publication Artículo científico (JournalArticle)

Sustainable conditions for waste tires recycling through gasification in a bubbling fluidized bed

  • Batuecas Fernández, Esperanza
  • Serrano García, Daniel
  • Horvat, Alen
  • Abelha, Pedro
Gasification in a bubbling fluidized bed reactor was introduced as sustainable technology to treat waste such as tires. However, uncertainty arises when defining the most sustainable gasification process conditions. In this paper, eight experimental conditions were analyzed. The experiments were carried out at 700 and 850 °C with different equivalence ratios (ER) while using air as a gasifying agent. At 850 °C the effect of steam addition was also studied. A Life Cycle Assessment (LCA) was assessed to the product gas and its energy content by the following environmental impacts: Climate Change (CC), Ozone Depletion (OD), and Particulate Matter (PM). LCA methodology revealed that optimal gasification conditions provide 74, 69 and 66% environmental impact reductions in CC, PM, and OD, respectively by comparing the best and the worst-case scenarios. The combination of high temperature, low ER, and steam addition offered the most environmentally sustainable process, achieving 8.3·10−2 kg CO2 eq/MJ in CC, 1.3·10−8 kg CFC-11eq/MJ in OD and 4.9·10−5 kg PM2.5eq/MJ in PM. Despite the great savings in environmental impacts, additional efforts are still needed to reduce the energy consumption of the preheating system to ensure the product gas is levelled to conventional natural gas., This research has received funding from the European Union's Horizon 2020 programme under grant agreement No 731101 (BRISK II project: Biofuels Research Infrastructure for Sharing Knowledge II). Funding for APC: Universidad Carlos III de Madrid (Read & Publish Agreement CRUE-CSIC 2023)
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Preparation of aromatic hydrocarbons from catalytic pyrolysis of digestate

  • Tan, Haodi
  • Yang, Minjiao
  • Chen, Yingquan
  • Chen, Xu
  • Fantozzi, Francesco
  • Bartocci, Pietro
  • Tschentscher, Roman
  • Bartonini, Federica
  • Yang, Haiping
  • Chen, Hanping
9 figures, 1 table.-- Supplementary information available.-- © 2023. This manuscript version is made available under the CC-BY-NC-ND 4.0 license https://creativecommons.org/licenses/by-nc-nd/4.0/, Catalytic pyrolysis of digestate to produce aromatic hydrocarbons can be combined with anaerobic fermentation to effectively transform and utilize all biomass components, which can achieve the meaningful purpose of transforming waste into high-value products. This study explored whether catalytic pyrolysis of digestate is feasible to prepare aromatic hydrocarbons by analyzing the thermogravimetric characteristics, pyrolysis characteristics, and catalytic pyrolysis characteristics of digestate. For digestate pyrolysis, an increase in temperature was found to elevate the CO, CH4, and monocyclic aromatic hydrocarbon (benzene, toluene, and xylene; BTX) content, whereas it decreased the contents of phenols, acids, aldehydes, and other oxygenates. Furthermore, the catalytic pyrolysis process effectively inhibited the acids, phenols, and furans in the liquid, whereas the yield of BTX increased from 25.45% to 45.99%, and the selectivity of xylene was also increased from 10.32% to 28.72% after adding ZSM-5. ZSM-5 also inhibited the production of nitrogenous compounds., This work was partially funded by the GTCLC-NEG project, which received funding from the European Union’s Horizon 2020 Research and Innovation Programme under the Marie Sklodowska-Curie Grant Agreement (101018756). The authors would like to thank the Brisk 2 European project (731101) for funding this project. The project acronym was B2PB-SIN2-1001, and the project title was “Optimization of catalytic pyrolysis of digestate and sewage sludge.” The authors would also like to acknowledge the COST Action CA17128 “Establishment of a Pan-European Network on the Sustainable Valorisation of Lignin (LignoCOST)” for useful discussions on lignin valorization., Peer reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Part 1-Impact of Pyrolysis Temperature and Wood Particle Length on Vapor Cracking and Char Porous Texture in Relation to the Tailoring of Char Properties

  • Maziarka, Przemyslaw
  • Kienzl, Norbert
  • Dieguez-Alonso, Alba
  • Fierro, Vanessa
  • Celzard, Alain
  • Arauzo, Pablo J.
  • Hedin, Niklas
  • Prins, Wolter
  • Anca-Couce, Andrés
  • Manyà, Joan J.
  • Ronsse, Frederik
Pore size distribution is a key parameter in the performance of biobased pyrolytic char in novel applications. In industrial-scale production, the size of feedstock particles typically exceeds a few millimeters. For such particle sizes, it is a challenge to tailor the final properties of the char based only on the process conditions (experimental and modeling-wise). Pyrolysis studies of single particles larger than a few millimeters provide data sets useful for modeling and optimization of the process. Part 1 of this research focused on the pyrolysis of single particles of beech wood, secondary cracking, and its effect on the char porous texture. It contains a quantitative assessment of the effects of five conversion temperatures (from 300 to 840 °C) and two particle dimensions (Ø8 × 10 mm and Ø8 × 16 mm) on the composition of the pyrolysis vapors and pore morphology of the char. Results from real-time temperature and mass changes are presented along with release profiles of 15 vapor constituents measured by infrared spectroscopy. Furthermore, characterization of the collected bio-oil (using GC-MS/FID) and the textural hierarchical structured char (through N2 and CO2 adsorption, Hg porosimetry, and scanning electron microscopy (SEM)) was performed. Cracking of vapors above 500 °C was compound-specific. The polyaromatic hydrocarbons (PAHs) yield, between 680 and 840 °C, increased 5 times for 10 mm particles and 9 times for 16 mm ones. Besides temperature, PAH yield was suspected to correlate with particle length and PAHs/soot deposition in the micropores. Results showed that the macropores accounted for over 80% of the total pore volume, regardless of the temperature and particle length. Increasing the particle length by 60% caused a reduction in the specific surface area (ca. 15% at 840 °C) of the resulting char, mainly due to a reduction in microporosity. Based on the findings, the production conditions for a specific char application are suggested. The obtained data will be used in Part 2 of this research, devoted to subsequent CFD modeling of the process.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Part 2 - Tailoring of pylolytic char properties with a single particle CFD model with a focus on the impact of shrinking, vapor cracking, and char permeability

  • Maziarka, Przemyslaw
  • Kienz, Norbert
  • Dieguez-Alonso, Alba
  • Prins, Wolter
  • Arauzo, Pablo J.
  • Skreiberg, Øyvind
  • Anca-Couce, Andrés
  • Manyà, Joan J.
  • Ronsse, Frederik
The prediction of the structural properties of biobased carbonaceous materials of pyrolytic origin (chars) with only base feedstock properties and process conditions still poses a challenge that hinders char tailoring for novel applications. CFD modeling of single biomass particle conversion can help solve this issue since it allows for the quantification of relations between parameters that are difficult to measure. A model for char tailoring must include a validated representation of the structural changes coupled to all other relevant phenomena occurring during conversion. Part 2 of this study focuses on finding the description of the mentioned aspects to achieve the highest precision of prediction of the structural changes in char by a CFD model. The investigation in Part 2 is composed of three cases focused on accurate description and prediction of (1) bulk density and porosity, (2) secondary vapor reactions on yields and soot formation, and (3) permeability, as well as the outflux and conversion of evolved vapors. The experimental results from Part 1 and the literature data were used to find appropriate descriptions of phenomena and assess the accuracy of the model. The model results indicate that for both particle lengths (10 and 16 mm), a high accuracy of prediction of base structural parameters was achieved. The average prediction error for temperatures between 400 and 840 °C of bulk density was 31 ± 15 kg/m3, and the porosity was 1.8 ± 1.1 vol %. The results also show a low error in the prediction of bulk product yields (dry basis) over the mentioned temperature range, which were: for char 2.8 ± 1.1 wt %, for the condensable fraction 6.5 ± 3.3 wt %, and for the pyrolysis gas 4.1 ± 1.9 wt %. The distribution of secondary char formation was found to be nonuniform below 500 °C. The changes in permeability had a minor influence on the vapor outflux but a non-negligible effect on the soot formation, especially at 840 °C. The results indicate a need for further improvement of the primary degradation model to increase the accuracy of the effect of soot formation on the char structure.
RUO. Repositorio Institucional de la Universidad de Oviedo
Publication Artículo científico (JournalArticle)

Eutectic solvents for the valorisation of the aqueous phase from hydrothermally liquefied black liquor

  • Pola Fernández, Lucía|||0000-0003-3565-8104
  • Collado Alonso, Sergio|||0000-0002-0224-918X
  • Wörner, M.
  • Hornung, U.
  • Díaz Fernández, José Mario|||0000-0001-6218-1140
Science, Innovation and University Office of Principality of Asturias (Spain) [BP19-041, EB21-04]; project GRUPIN [AYUD/2021/51041]; Spanish Ministry of Science and Innovation (MCIN) [MCIU-22-PID2021-125942OB-I00]; Horizon 2020's Research and Innovation Programme [731101, 884111]
RUO. Repositorio Institucional de la Universidad de Oviedo
Publication Artículo científico (JournalArticle)

Valorisation of the residual aqueous phase from hydrothermally liquefied black liquor by persulphate-based advanced oxidation

  • Pola Fernández, Lucía|||0000-0003-3565-8104
  • Collado Alonso, Sergio|||0000-0002-0224-918X
  • Wörner, M.
  • Hornung, U.
  • Díaz Fernández, José Mario|||0000-0001-6218-1140
The authors are grateful for the financial support from the Science, Innovation and University Office of Principality of Asturias (Spain) through the Severo Ochoa pre-doctoral aid programme (BP19-041), its funding for short stays in research institutions (EB21-04) and the project GRUPIN AYUD/2021/51041, and from the State Research Agency through the project MCIU-22-PID2021-125942OB-I00. Authors also acknowledge the funding from Horizon 2020’s Research and Innovation Programme [grant agreement number 731101 (BRISK2) and 884111 (BL2F)].