Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 27
Encontrada(s) 1 página(s)

e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publication Artículo científico (JournalArticle)

Impact of surface roughness on the formation of necking instabilities in additive manufactured porous metal plates subjected to dynamic plane strain stretching

  • Murlidhar, Anil Kumar
  • Nieto Fuentes, Juan Carlos
  • Rodríguez Martínez, José Antonio
This paper investigates the influence of surface roughness on multiple necking formation in additive manufactured porous ductile plates subjected to dynamic plane strain stretching. For this purpose, we have developed a computational model in ABAQUS/Explicit which includes surface texture and discrete voids measured from 3D-printed metallic specimens using optical profilometry and X-ray tomography analysis, respectively. The mechanical behavior of the material is described using an elastic–plastic constitutive model, with yielding defined by the isotropic von Mises criterion, an associated flow rule, and a power-law function for the yield stress evolution which depends on plastic strain, plastic strain rate, and temperature. The finite element calculations have been conducted across a broad range of strain rates, from 5000 s−1 to 50000 s−1, to explore the interactions among inertia, surface roughness, and porosity in determining the necking pattern that emerges in the plates at large strains. The finite element results show that surface roughness induces perturbations in the deformation field of the specimen, which lead to early necking localization, while the location and number of necks formed are primarily controlled by the porous microstructure and the loading rate. The results for the neck spacing have shown quantitative agreement with the analytical stability analysis predictions and the unit-cell finite element calculations reported by Rodríguez-Martínez et al. [1]. Moreover, integrating discrete voids into simulations that already account for surface roughness results in a minor reduction in necking strain: surface roughness and porosity demonstrate similar quantitative impacts on necking ductility, which is primarily influenced by inertia effects at the highest strain rates studied. To the best of the authors’ knowledge, this paper presents the first calculations that explore dynamic plastic localization in additive manufactured metals, incorporating actual surface roughness and explicit void representation derived from experimental measurements. This work marks progress in the analysis of 3Dprinted structures under impact loading, aiming to understand and predict the mechanics influencing their energy absorption capacity at high strain rates., The research leading to these results has received funding from the European Research Council (ERC) under the European Union’s Horizon 2020 research and innovation programme. Project PURPOSE, grant agreement 758056. J. C. Nieto-Fuentes acknowledges support from the CONEX-Plus programme funded by Universidad Carlos III de Madrid and the European Union’s Horizon 2020 research and innovation programme , under the Marie Skłodowska-Curie grant agreement 801538
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publication Tesis doctoral (DoctoralThesis)

Computational modeling of the mechanical behavior of ductile metals with anisotropic constitutive models

  • Hosseini, Navab
Ductile metals are commonly used to build protective structures, which may be subjected to quasi-static or dynamic loads. When a sufficient amount of load is applied, the structure deforms plastically. A ductile failure occurs when a structure undergoes significant plastic deformation and can no longer absorb the energy of the applied load. In recent decades, numerous studies have been conducted on the failure of ductile metals, leading to a deeper understanding of the effects of anisotropy, tension-compression asymmetry, porosity, strain rate, and temperature dependence on plastic instabilities and ductile failure. However, the effects of anisotropy on the ductile failure deserve further analysis. This dissertation contributes to the understanding of the key role that material behavior plays in the evolution of quasi-static ductile failure, with a particular focus on anisotropy. To investigate the effects of anisotropy on quasi-static ductile failure, we first developed a reliable and computationally efficient stress integration scheme. Using this scheme, we implemented three elastic isotropic and plastic anisotropic constitutive models with yielding described by the Yld2004-18p, CPB06ex2, and Yld2011-27p criteria, respectively, in the finite element code ABAQUS. We then performed finite element calculations using a cubic unit cell model with a spherical void in the center. Subsequently, we employed an innovative approach to demonstrate that anisotropy may either promote or postpone ductile failure. The study reveals that anisotropy plays a critical role in determining the onset and progression of failure. The findings highlight the need for a nuanced understanding of material anisotropy to predict and mitigate the risks of ductile failure in protective structures, The research leading to the results reported in this doctoral thesishas received funding from the European Research Council (ERC) under the European Union’s Horizon 2020 research and innovation programme. Project PURPOSE, grant agreement 758056., Programa de Doctorado en Ingeniería Mecánica y de Organización Industrial por la Universidad Carlos III de Madrid, Presidente: Javier Segurado Escudero.- Secretario: Lars Edvard Blystad Dæhli.- Vocal: Cihan Tekoglu
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publication Artículo científico (JournalArticle)

Modeling dynamic spherical cavity expansion in elasto-viscoplastic media

  • Santos, T. dos
  • Brezolin, A.
  • Rossi, R.
  • Rodríguez-Martínez, José A.
In this paper, we extend the dynamic spherical cavity expansion model for rate-independent materials developed by Durban and Masri (Int J Solids Struct 41(20):5697-5716, 2004), Masri and Durban (J Appl Mech 72(6):887-898, 2005), and Cohen et al. (J Appl Mech 77(4):041009, 2010) to viscoplastic media. For that purpose, we describe the material behavior with an isotropic Perzyna-type overstress formulation (Perzyna in Q Appl Math 20:321&#-332, 1963; Adv Appl Mech 9:243-377, 1966) in which the material rate dependence is controlled by the viscosity parameter η. The theoretical predictions of the cavity expansion model, which assumes that the cavity expands at constant velocity, are compared with finite element simulations performed in ABAQUS/Explicit (Abaqus Explicit v6.13 User's Manual, ABAQUS Inc., Richmond). The agreement between theory and numerical simulations is excellent for the whole range of cavitation velocities investigated, and for different values of the parameter η. We show that, as opposed to the steady-state self-similar solutions obtained for rate-independent materials (Durban and Masri 2004; Masri and Durban 2005; Cohen et al. 2010), the material viscosity leads to time-dependent cavitation fields and stress relaxation as the cavity enlarges. In addition, we also show that the material viscosity facilitates to model the shock waves that emerge at the highest cavitation velocities investigated, controlling the amplitude and the width of the shock front., The research leading to these results has received funding from the European Research Council (ERC) under the European Union's Horizon 2020 research and innovation programme. Project PURPOSE, Grant Agreement 758056. RR wishes to acknowledge the support of CNPq, Conselho Nacional de Desenvolvimento Científico e Tecnológico, grant number 306058/2018-9.
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publication Artículo científico (JournalArticle)

Dynamic spherical cavity expansion in Gurson materials with uniform and non-uniform distributions of porosity

  • Santos, T. dos
  • N Souglo, Komi Espoir
  • Rodríguez-Martínez, José A.
This paper investigates both theoretically and using finite elements the elastoplastic field induced by a pressurized spherical cavity expanding dynamically in an infinite medium modelled using the Gurson&-Tvergaard&-Needleman porous plasticity approach. The theoretical model, which assumes that the porosity is uniformly distributed in the material and the cavitation fields are self-similar, incorporates artificial viscous stresses into the original formulation of Cohen and Durban (2013b) to capture the shock waves that emerge at high cavitation velocities. The finite element calculations, performed in ABAQUS/Explicit (2013) using the Arbitrary Lagrangian Eulerian adaptive meshing available in the code, simulate the cavity expansion process in materials with uniform and non-uniform distributions of porosity. The finite element results show that the distribution of porosity has small influence on the cavitation velocity, as well as on the location of the shock wave, which are primarily determined by the cavity pressure and the average material properties. In contrast, it is shown that the intensity of the shock wave, evaluated based on the maximum value of the plastic strain rate within the shock, depends on the local material porosity. The ability of the theoretical model to reproduce the numerical results obtained for the various distributions of porosity used in this work is exposed and discussed., The research leading to these results has received funding from the European Research Council (ERC) under the European Union’s Horizon2020 research and innovation programme. Project PURPOSE, grant agreement 758056.
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publication Artículo científico (JournalArticle)

Size effects on the plastic shock formation in steady-state cavity expansion in porous ductile materials

  • Dos Santos, Tiago
  • Rodríguez Martínez, José Antonio
In this paper, we have studied the hypervelocity expansion of a spherical cavity in an infinite medium modeled with the extension of the porous plasticity criterion of Gurson (1977) developed by Chen and Yuan (2002) to account for plastic strain gradient induced size effects. Following the self-similar, steady-state solution derived by Cohen and Durban (2013) for size-independent porous materials, we have computed the critical cavity expansion velocity which leads to the emergence of plastic shock waves for a wide range of initial void volume fractions and different values of the length scale parameter that controls the effect of size. We have shown that size effects hinder the emergence of plastic shock waves, so that as the length scale parameter increases, the expansion velocity required for the plastic shock to be formed increases. In addition, while porosity favors the formation of plastic shocks, as shown by Cohen and Durban (2013), our results indicate that the effect of initial void volume fraction on plastic shock wave formation decreases for size-dependent materials., TdS wishes to acknowledge the support of FAPERGS, Fundaçã de Amparo à Pesquisa do Estado do Rio Grande do Sul, grant agreement 19/2551-0001054-0. JAR-M acknowledges the financial support obtained from the European Research Council (ERC) under the European Union’s Horizon 2020 research and innovation programme. Project PURPOSE, grant agreement 758056.
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publication Artículo científico (JournalArticle)

A simple and computationally efficient stress integration scheme based on numerical approximation of the yield function gradients: Application to advanced yield criteria

  • Hosseini, Navab
  • Rodríguez-Martínez, José A.
In this paper, we have modified the stress integration scheme proposed by Choi and Yoon [1]; which is based on the numerical approximation of the yield function gradients, to implement in the finite element code ABAQUS three elastic isotropic, plastic anisotropic constitutive models with yielding described by Yld2004-18p [2], CPB06ex2 [3] and Yld2011-27p [4] criteria, respectively. We have developed both VUMAT and UMAT subroutines for the three constitutive models, and have carried out cylindrical cup deep drawing test simulations and calculations of dynamic necking localization under plane strain tension, using explicit and implicit analyses. An original feature of this paper is that these finite element simulations are systematically compared with additional calculations performed using (i) the numerical approximation scheme developed by Choi and Yoon [1]; and (ii) the analytical computation of the first and second order yield functions gradients. This comparison has shown that the numerical approximation of the yield function gradients proposed in this paper facilitates the implementation of the constitutive models, and in the case of the implicit analyses, it leads to a significant decrease of the computational time without impairing the accuracy of the finite element results. In addition, we have demonstrated that there is a critical loading rate below which the dynamic implicit analyses are computationally more efficient than the explicit calculations., The research leading to these results has received funding from the European Research Council (ERC) under the European Union’s Horizon 2020 research and innovation programme. Project PURPOSE, grant agreement 758056.
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publication Tesis doctoral (DoctoralThesis)

Multiple localization and fracture in metallic rings and plates subjected to dynamics expansion

  • Murlidhar, Anil Kumar
Ductile materials are commonly used in high-strain rate applications involving impact or blast loads due to their notable capacity to absorb energy and undergo plastic deformation before fracture. Over the last two decades, studies on dynamic strain rates have evolved dramatically, leading to a better knowledge of material behavior under high-speed loading situations and generating advances in a variety of industries. Imperfections in ductile metals, such as cracks, inclusions, and voids, are significant, and these imperfections can significantly impact the material’s mechanical properties and structural integrity, thereby affecting its suitability for various industrial applications. Hence, further research is necessary to understand the mechanical behavior of ductile metals with imperfections. This doctoral thesis investigates the effect of porosity, anisotropy, and tensioncompression asymmetry on the mechanical response of metallic materials under dynamic loading conditions. In the first part of the thesis, we used linear stability analysis and unit-cell finite element calculations to investigate the onset of necking instabilities in porous ductile plates under biaxial loading. In the next part of the work, we used three techniques-linear stability analysis, a nonlinear two-zone model, and unit-cell finite element calculations-to examine the necking formability of anisotropic and tension-compression asymmetric metallic sheets subjected to in-plane loading paths spanning plane strain tension to near equal-biaxial tension. The last part of the study focused on examining the fragmentation process of 3D-printed AlSi10Mg porous ring specimens. This was achieved by implementing two experimental ring expansion test setups and subjecting the aluminum alloy to electromagnetic and mechanical loadings. The objective was to gain insights into the behavior of these alloys when exposed to high strain rates., The research leading to the results reported in this doctoral thesis has received funding from European Research Council (ERC) under the European Union's Horizon 2020 research and innovation programme. Project PURPOSE, grant agreement 758056., Presidente: Ahmed Benallal. Vocal: Christophe Czarnota. Secretario: Borja Erice Echavarri
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publication Artículo científico (JournalArticle)

Real-time in-situ X-ray imaging of pore compaction and spall fracture in plate impact tests on additively manufactured metals

  • Virazels, Thomas
  • García Molleja, J.
  • Lukic, B.
  • Foster, D.
  • Rack, A.
  • Puerta Hueso, Sergio
  • Pedroche Arias, David
  • Rodríguez Martínez, José Antonio
  • Sket, F.
This paper presents direct, in-situ, real-time X-ray observations of pore compaction and spall frac-ture in porous additively manufactured metals under high-velocity loading. To this end, planar plate impact experiments were conducted using a mesoscale gas launcher at the ID19 beamline of the European Synchrotron Radiation Facility on disc-shaped Ti6Al4V and AlSi10Mg speci-mens produced by laser powder bed fusion. The two alloys exhibit markedly different mechanical properties and distinct void volume fractions, ranging from 0.04% to 0.77%, with broad pore size distributions extending from a few micrometers to over 180 𝜇m. The cylindrical samples had a diameter of 6 mm and two thicknesses, 1.2 and 2 mm. These reduced dimensions were dictated by the combined constraints of the synchrotron-based impact setup and the X-ray diagnostics, ensuring compatibility with the gas launcher and sufficient transmission for high-resolution X-ray radiography. The tests were performed at impact velocities ranging from 225 to 738 m/s, spanning the transition from the onset of damage to complete spall cavity formation. An indirect detector system combining three ultra-high-speed cameras operating in alternating-frame mode enabled X-ray phase-contrast measurement of the porous microstructure with a temporal resolution of 176 ns (single-bunch mode) and a pixel size of 16 𝜇m, capturing pore collapse during compression and subsequent void growth and spall fracture under tension. A photonic Doppler velocimetry system synchronized with the X-ray imaging established a direct correspondence be-tween the specimen’s free-surface velocity signal and the in-situ microstructural processes of pore collapse, pore re-opening, and spall fracture, enabling the porous microstructure to be resolved at key stages of the shock-loading response, including the Hugoniot elastic limit, the plastic shock front, the peak-velocity plateau, and the pullback velocity. In addition, the recording of the free-surface velocity provided measurements of spall strength, which showed good agreement with literature data and validated the dedicated setup developed in this study for in-situ, real-time plate impact testing. Furthermore, a systematic comparison of X-ray tomography scans on se-lected samples before and after testing enabled a direct assessment of the pre- and post-mortem shape and size of individual voids. The analysis reveals that spall fracture involves large pre-existing pores generated during printing, micrometric pores approaching the resolution limit of the tomograms, sub-micrometer pores beyond tomographic detection, and additional pores likely nucleated during dynamic loading. The tomography analysis also allowed reconstruction of the spallation patterns and highlighted the differences in fracture morphology between the two ma-terials tested. The observations reported in this work establish a direct connection between pore-scale mechanisms and the macroscopic fracture response of AlSi10Mg and Ti6Al4V, providing a robust experimental framework for investigating dynamic failure in additively manufactured metals., The research leading to these results has received funding from the European Research Council (ERC) under the European Union’s Horizon 2020 research and innovation programme. Project PURPOSE, grant agreement 758056. This research has been supported by a 2021 Leonardo Grant for Researchers and Cultural Creators, BBVA Foundation. Project MIRROR, grant agreement IN[21] ING ING 0052. Thomas Virazels acknowledges financial support from the Spanish Ministry of Science, Innovation and Universities through an FPI predoctoral fellowship [PREP2022-000187] under the project UNCLOAK [Grant No. PID2022-137559NB-I00].
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publication Artículo científico (JournalArticle)

Multiple necking patterns in elasto-plastic rings subjected to rapid radial expansion: the effect of random distributions of geometric imperfections

  • Marvi Mashhadi, Mohammad
  • Rodríguez-Martínez, José A.
In this paper we have investigated, using finite element calculations performed in ABAQUS/Explicit [1], the effect of ab initio geometric imperfections in the development of multiple necking patterns in ductile rings subjected to dynamic expansion. Specifically, we have extended the work of Rodríguez-Martínez et al. [2], who studied the formation of necks in rings with sinusoidal spatial perturbations of predefined amplitude and constant wavelength, by considering specimens with random distributions of perturbations of varying amplitude and wavelength. The idea, which is based on the work of El Maï et al. [3], is to provide an idealized modeling of the surface defects and initial roughness of the rings and explore their effect on the collective behavior and spacing of the necks. The material behavior has been modeled with von Mises plasticity and constant yield stress, and the finite element simulations have been performed for expanding velocities ranging from 10 m/s to 1000 m/s, as in ref. [2]. For each speed, we have performed calculations varying the number of imperfections in the ring from 5 to 150. In order to obtain statistically significant results, for each number of imperfections, the computations have been run with five random distributions of imperfection wavelengths. For a small number of imperfections, the variability in the wavelengths distribution is large, which makes the imperfections play a major role in the necking pattern, largely controlling the spacing and growth rate of the necks. As the number of imperfections increases, the variability in the wavelengths distribution decreases, giving rise to an array of more regularly spaced necks which grow at more similar speed. A key outcome is to show that, for a large number of imperfections, the number of necks formed in the ring comes closer to the number of necks obtained in the absence of ab initio geometric imperfections., The research leading to these results has received funding from the European Research Council (ERC) under the European Union’s Horizon 2020 research and innovation programme. Project PURPOSE, grant agreement 758056.
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publication Artículo científico (JournalArticle)

Modeling dynamic formability of porous ductile sheets subjected to biaxial stretching: Actual porosity versus homogenized porosity

  • Nieto Fuentes, Juan Carlos
  • Jacques, N.
  • Marvi Mashhadi, Mohammad
  • N Souglo, Komi Espoir
  • Rodríguez-Martínez, José A.
This paper investigates the effect of porous microstructure on the necking formability of ductile sheets subjected to dynamic in-plane stretching. We have developed an original approach in which finite element calculations which include actual void distributions obtained from additively manufactured materials are compared with simulations in which the specimen is modeled with the Gurson–Tvergaard continuum plasticity theory (Gurson, 1977; Tvergaard, 1982) which considers porosity as an internal state variable. A key point of this work is that in the calculations performed with the continuum model, the initial void volume fraction is spatially varied in the specimen according to the void distributions included in the simulations with the actual porous microstructure. The finite element computations have been carried out for different loading conditions, with biaxial strain ratios ranging from 0 (plane strain) to 0.75 (biaxial tension) and loading rates varying between 10000 s −1 and 60000 s −1. We have shown that for the specific porous microstructures considered, the necking forming limits obtained with the Gurson–Tvergaard continuum model are in qualitative agreement with the results obtained with the calculations which include the actual void distributions, the quantitative differences for the necking strains being generally less than ≈ 25% (the calculations with actual voids systematically predict greater necking strains). In addition, the spatial distribution of necks formed in the sheets at large strains is very similar for the actual porosity and the homogenized porosity models. The obtained results demonstrate that the voids promote plastic localization, acting as preferential sites for the nucleation of fast growing necks. Moreover, the simulations have provided individualized correlations between void volume fraction, maximum void size and necking formability, and highlighted the influence of the heterogeneity of the spatial distribution of porosity on plastic localization., The research leading to these results has received funding from the European Research Council (ERC) under the European Union's Horizon 2020 research and innovation programme. Project PURPOSE, grant agreement 758056. J. C. Nieto-Fuentes acknowledges support from the CONEX-Plus programme funded by Universidad Carlos III de Madrid and the European Union's Horizon 2020 research and innovation programme, under the Marie Sklodowska-Curie grant agreement 801538. J. A. Rodríguez-Martínez acknowledges the financial support provided by the Spanish Ministry of Science and Innovation under the programme Proyectos I+D Excelencia 2017. Project APPLIED, DPI2017-88608-P.
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publication Artículo científico (JournalArticle)

Gas gun driven dynamic expansion of 3D-printed AlSi10Mg rings

  • Nieto Fuentes, Juan Carlos
  • Virazels, Thomas
  • Jacques, Nicolas
  • Rodríguez-Martínez, José A.
This paper presents a new experimental setup to study dynamic fragmentation of metallic rings manufactured by 3D-printing technology. The ring is inserted over a ductile thin-walled tube which is impacted axially by a conical-nosed cylindrical projectile fired by a single-stage ligh-gas gun. The diameter of the projectile is larger than the internal diameter of the thin-walled tube, which expands as the projectile advances, pushing radially outwards the metallic ring, that eventually breaks into multiple fragments. The impact velocities considered in the present experimental campaign range from 197 m/s to 385 m/s. The AlSi10Mg ring specimens are printed by Selective Laser Melting technique, with an inner diameter of 14 mm and square cross section of 2 × 2 mm2. To obtain time-resolved information on the mechanics of fragmentation, the number of fractures, and the size of the fragments, the tests have been recorded with two-high speed cameras. A tunnel-shaped soft casing made of polymer foam is placed around the specimen to softly recover the ejected fragments, that have been weighted and sized to determine the statistics of the fragments size distribution. In addition, the predictions of the fragmentation theory of Kipp and Grady (1985) for the evolution of the number of fragments with the impact velocity have been compared with the experimental evidence, and an excellent quantitative agreement has been found within the whole range of loading rates investigated. Compared to other available techniques for dynamic fragmentation of rings, in which the expansion of the specimen is driven by electromagnetic or explosive loading, this experimental setup stands out for its simplicity, fast operation, quick assembly, and flexibility to test different engineering materials, which facilitates performing extensive experimental campaigns (34 successful tests have been carried out in this research). To the authors" knowledge, this paper presents the most comprehensive data set to date on the fragmentation of dynamically expanded printed rings, including the first high-resolution video recordings of the formation of multiple cracks throughout the circumference of the samples, and scanning electron microscopy images of the fractures showing the porous microstructure on the cracks surface., The research leading to these results has received funding from the European Research Council (ERC) under the European Union’s Horizon 2020 research and innovation programme (Project PURPOSE), grant agreement No. 758056. J. C. Nieto-Fuentes acknowledges support from the CONEX-Plus programme funded by Universidad Carlos III de Madrid and the European Union’s Horizon 2020 research and innovation programme, under the Marie Sklodowska-Curie grant agreement No. 801538
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publication

Void growth in ductile materials with realistic porous microstructures

  • Ambikadevi Rajasekharan Nair, Vishnu
  • Vadillo Martín, Guadalupe
  • Rodríguez-Martínez, José A.
  • Rodríguez Martínez, Guillermo
In this paper, we have investigated void growth in von Mises materials which contain realistic porous microstructures. For that purpose, we have performed finite element calculations of cubic unit-cells which are subjected to periodic boundary conditions and include porosity distributions representative of three additively manufactured metals. The initial void volume fraction in the calculations varies between 0.00564% and 1.75%, the number of actual voids between 14 and 5715, and the pores size from 2.3mum to 110mum. Several tests with different void sizes and positions have been generated for each of the three porous microstructures considered, and for each test we have performed several realizations with different spatial arrangement of the voids. The simulations have been carried out with random spatial distributions of pores and with clusters of the same size and different void densities. The macroscopic stress state in the unit-cell is controlled by prescribing constant triaxiality and Lode parameter throughout the loading. Calculations performed exchanging the loading directions for a given distribution of void sizes and positions have shown that the porous microstructure makes the macroscopic strain softening of the unit-cell (slightly) anisotropic. Moreover, the results obtained with the realistic porous microstructures have been compared with unit-cell calculations having an equivalent single central pore, and with calculations in which the material behavior is modeled with Gurson plasticity. It has been shown that both initial void volume fraction and spatial and size distribution of voids affect the macroscopic response of the porous aggregate and the void volume fraction evolution. Moreover, the calculations with random spatial distribution of voids have brought out that different tests of the same microstructure carry significant variations to the effective behavior of the porous aggregate, and that the interaction between neighboring pores dictates the volume evolution of individual voids, especially at higher macroscopic triaxiality. The calculations with clusters have shown that pores clustering promotes localization/coalescence due to increased interaction between the voids, which results in an increased growth rate of voids in clusters with large number of pores. Moreover, the results for the evolution of the distribution of plastic strains in the unit-cell have provided quantitative indications of the role of porous microstructure on the development of heterogeneous plastic strain fields which promote macroscopic strain softening. Namely, the accelerated growth rate of the plastic strains near the voids which indicates the onset of localization/coalescence has been shown to occur earlier as the number of voids in the microstructure increases., The research leading to these results has received funding from the European Research Council (ERC) under the European Union’s Horizon 2020 research and innovation programme. Project PURPOSE, grant agreement 758056. G. Vadillo acknowledges the financial support provided by the Spanish Ministry of Science and Innovation under the programme Proyectos I+D Excelencia 2017. Project APPLIED, DPI2017-88608-P. This work has been supported by the Madrid Government (Comunidad de Madrid-Spain) under the Multiannual Agreement with UC3M in the line of Excellence of University Professors (EPUC3M24), and in the context of the V PRICIT (Regional Programme of Research and Technological Innovation)., Publicado
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publication Artículo científico (JournalArticle)

The effect of voids shape on hypervelocity cylindrical cavity expansion and shock waves formation in transversely isotropic porous materials

  • Dos Santos, Tiago
  • Nieto Fuentes, Juan Carlos
  • Hosseini, Navab
  • Rodríguez-Martínez, José A.
The research leading to these results has received funding from the European Research Council (ERC) under the European Union’s Horizon 2020 research and innovation program. Project PURPOSE, grant agreement 758056. TdS wishes to acknowledge the support of FAPERGS, Fundação de Amparo à Pesquisa do Estado do Rio Grande do Sul, grant agreements 19/2551 − 0001054 − 0 and 21/2551 − 0000744 − 3.
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publication Tesis doctoral (DoctoralThesis)

Role of porous microstructure on dynamic shear localization and ductile failure

  • Ambikadevi Rajasekharan Nair, Vishnu
This doctoral thesis aims to provide a comprehensive analysis of the role of porous microstructure on dynamic shear localization and ductile failure. For this purpose, a computational approach was developed that includes large-scale 3D finite element models incorporated with actual porous microstructures that are derived from different additively manufactured materials. This is the distinctive feature of the numerical simulations conducted in this study, in which a large population of voids that are statistically representative of the actual porosity in 3D-printed metals has been included. Additional microstructures varying the void volume fraction, the mean and standard deviation of the size distribution of voids were generated, enabling a systematic parametric analysis of the microstructural features. Finite element simulations of multiple shear bands formation in radially collapsing thick-walled cylinders and shear band formation in thin-tubes subjected to dynamic torsion were performed to investigate the effect of spatial and size distribution of voids on dynamic shear localization. The numerical results demonstrate that microstructural porosity promotes dynamic shear localization, determining preferential sites for the nucleation of the shear bands, accelerating their development, and tailoring their direction of propagation. Specifically, collapsing thick-walled cylinder calculations bring out that, for a given void volume fraction more shear bands are nucleated as the number of voids increases, while the shear bands are triggered earlier and develop faster as the size of the pores increases. Moreover, the numerical results for porous thin-tubes subjected to dynamic torsion quantitatively show that the size of the largest pore is a main microstructural feature controlling the specimen ductility. Furthermore, this numerical methodology was extended to perform unit-cell calculations to investigate the void growth in porous ductile materials under monotonic loading conditions by prescribing constant triaxiality and Lode parameter throughout the loading. The simulations were carried out with random spatial distributions of pores and with void clusters. The calculations with random spatial distribution of voids revealed that the interaction between neighboring pores dictates the volume evolution of individual voids, especially at higher macroscopic triaxiality. The calculations with clusters demonstrated that pores clustering promotes localization/coalescence due to increased interaction between the voids, resulting in an increased growth rate of voids in clusters with large number of pores. Moreover, the results for the evolution of the distribution of plastic strains in the unit-cell have provided some quantitative indications of the role of porous microstructure on the development of heterogeneous plastic strain fields which promote macroscopic strain softening., The research leading to the results reported in this doctoral thesis has received funding from the European Research Council (ERC) under the European Union’s Horizon 2020 research and innovation programme. Project PURPOSE, grant agreement 758056., Programa de Doctorado en Ingeniería Mecánica y de Organización Industrial por la Universidad Carlos III de Madrid, Presidente: Alain Molinari.- Secretario: Shmuel Osovski.- Vocal: Tore Børvik
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publication Artículo científico (JournalArticle)

High-velocity fragmentation of titanium alloy rings and cylinders produced using Field-Assisted Sintering Technology

  • Virazels, Thomas
  • Lister, S.
  • Levano Blanch, O.
  • Jackson, M.
  • Rodríguez Martínez, José Antonio
  • Nieto Fuentes, Juan Carlos
This paper explores the mechanics of high-velocity impact fragmentation in titanium alloys pro-duced by Field-Assisted Sintering Technology. For that purpose, we have utilized the experimental setups recently developed by Nieto-Fuentes et al. (J Mech Phys Solids 174:105248, 2023a; Int J Impact Eng 180:104556, 2023b) for conducting dynamic expan-sion tests on rings and cylinders. The experiments involve firing a conical-nosed cylindrical projectile using a single-stage ight-gas gun against the stationary ring/cylinder at velocities ranging from ≈ 248 m/sto≈ 390 m/s, corresponding to estimated strain rates in the specimen varying from ≈ 10050 s−1 to ≈ 19125 s−1. The diameter of the cylindrical part of the projec-tile exceeds the inner diameter of the ring/cylinder, causing the latter to expand as the projectile moves forward, resulting in the formation of multiple necks and fragments. Two different alloys have been tested: Ti6Al4V and Ti5Al5V5Mo3Cr. These materials are widely utilized in aeronautical and aerospace industries for constructing structural elements such as compres-sor parts (discs and blades) and Whipple shields, which are frequently exposed to intense mechanical loading, including high-velocity impacts. However, despite the scientific and technological significance of Ti6Al4V and Ti5Al5V5Mo3Cr, and the extensive research on their mechanical and fracture behaviors, to the best of the authors’ knowledge, no systematic study has been conducted thus far on the dynamic fragmentation behavior of these alloys. Hence, this paper presents an ambitious fragmentation testing program, encom-passing a total of 27 and 29 experiments on rings and cylinders, respectively. Monolithic and multimaterial samples—half specimen of Ti6Al4V and half specimen of Ti5Al5V5Mo3Cr—have been tested, taking advan-tage of the ability of Field-Assisted Sintering Technol-ogy to produce multimaterial parts. The fragments have been collected, weighed, sized, and analyzed using scanning electron microscopy. The experiments have shown that the number of necks, the number of frag-ments, and the proportion of necks developing into fragments generally increase with expansion velocity. The average distance between necks has been assessed against the predictions of a linear stability analysis (Zhou et al. in Int J Impact Eng 33:880–891 2006; Vaz-Romero et al. in Int J Solids Struct 125:232–243, 2017), revealing satisfactory agreement between the-oretical predictions and experimental results. In addi-tion, the experimental results have been compared with tests reported in the literature for various metals and alloys (Nieto-Fuentes et al. in J Mech Phys Solids 174:105248, 2023a; Zhang and Ravi-Chandar in Int J Fract 142:183–217, 2006, Zhang and Ravi-Chandar, Open Access funding provided thanks to the CRUE-CSIC agreement with Springer Nature. The research leading to these results has received funding from the European Research Council (ERC) under the European Union’s Horizon 2020 research and innovation programme. Project PURPOSE, grant agreement 758056. J. C. Nieto-Fuentes acknowledges support from the CONEX-Plus programme funded by Universidad Carlos III de Madrid and the European Union’s Horizon 2020 research and innovation programme, under the Marie Skłodowska-Curie grant agreement 801538. This work was supported through the Engineering and Physical Sciences Research Council (EPSRC), grant EP/T024992/1 Doing More With Less. The EPSRC for funding equipment in the Henry Royce Institute at Sheffield, grant numbers EP/R00661X/1 and EP/P02470X/1, is gratefully acknowledged.
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publication Artículo científico (JournalArticle)

Dynamic cylindrical cavity expansion in orthotropic porous ductile materials

  • Santos, T. dos
  • Vaz-Romero, Álvaro
  • Rodríguez-Martínez, José A.
This paper investigates the steady-state elastoplastic fields induced by a pressurized cylindrical cavity expanding dynamically in an anisotropic porous medium. For that task, we have developed a theoretical model which: (i) incorporates into the formalism developed by Cohen and Durban [4] the effect of plastic anisotropy using the constitutive framework developed by Benzerga and Besson [1] and (ii) uses the artificial viscosity approach developed by Lew et al. [24] to capture the shock waves that emerge at high cavity expansion velocities. We have shown that while the development of the shock waves is hardly affected by the material anisotropy, the directionality of the plastic properties does have an effect on the elastoplastic fields that evolve near the cavity. The importance of this effect is strongly dependent on the cavity expansion velocity, the initial porosity and the strain hardening of the material. In addition, the theoretical model has been used in conjunction with the Recht and Ipson [33] formulas to assess the ballistic performance of porous anisotropic targets against high velocity perforation., The research leading to these results has received funding from the European Research Council (ERC) under the European Union's Horizon 2020 research and innovation programme. Project PURPOSE, grant agreement 758056.
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publication Artículo científico (JournalArticle)

The effect of material orientation on void growth

  • Hosseini, Navab
  • Nieto Fuentes, Juan Carlos
  • Dakshinamurthy, Manjunath
  • Rodríguez Martínez, José Antonio
  • Vadillo Martín, Guadalupe
In this work, we have brought to light the effect of material orientation on void growth. For that purpose, we have performed finite element calculations using a cubic unit-cell model with a spherical void at its center and subjected to periodic boundary conditions. The behavior of the material is described with an elastic isotropic, plastic orthotropic constitutive model with yielding defined by Yld2004-18p criterion (Barlat et al., 2005). We have used the multi-point constraint subroutine developed by Dakshinamurthy et al. (2021) to enforce constant values of macroscopic stress triaxiality T and Lode parameter L in calculations that have been carried out for different stress states resulting from the combination of T = 0.33, 1 and 2, with L = − 1, 0 and 1 (axisymmetric tension, generalized shear and axisymmetric compression, respectively). Firstly, we have performed numerical simulations in which the loading directions are collinear with the orthotropy axes of the material, so that the principal directions of macroscopic stress and strain are parallel. Investigation of the cases for which the minor loading axis coincides either with the rolling, the transverse or the normal direction, has shown that the initially spherical void turns into an ellipsoid whose rate of growth and eccentricity depend on both stress state and material orientation. A key result is that for specific material orientations the anisotropy switches the effect of Lode parameter on void growth, reversing the trends obtained for isotropic von Mises mate rials. Secondly, we have carried out calculations using a novel strategy which consists of including angular misalignments within the range 0∘ ≤ theta ≤ 90∘ , so that one loading direction is parallel to one of the symmetry axes of the material, and theta is the angle formed between the other two loading directions and the second and third orthotropy axes. In fact, to the authors" knowledge, these are the first unit-cell calculations ever reported in which the material is modeled using a macroscopic anisotropic yield function with prescribed misalignment between loading and material axes and, at the same time, the macroscopic stress triaxiality and the Lode parameter are controlled to be constant during loading. The finite element calculations have shown that the misalignment between loading and material axes makes the void and the faces of the unit-cell to rotate and twist during loading. Moreover, the main contribution of this work is the identification of an intermediate value of the angle theta for which the growth rate of the void reaches an extreme value (minimum or maximum), so that the numerical results indicate that material orientation and angular misalignment can be strategically exploited to control void growth, and thus promote or delay localization and fracture of anisotropic metal products. The conclusions of this research have been shown to be valid for three different materials (aluminum alloys 2090-T3, 6111-T4 and 6013) and selected comparisons have also been performed using two additional yield criteria (CPB06ex2 and Yld2011-27p)., The research leading to these results has received funding from the European Research Council (ERC) under the European Union's Horizon 2020 research and innovation programme. Project PURPOSE, grant agreement 758056. The authors express sincere gratitude to Dr. Oana Cazacu (University of Florida) for helpful discussions on plastic anisotropy of metallic materials.
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publication Artículo científico (JournalArticle)

High-velocity impact fragmentation of additively-manufactured metallic tubes

  • Nieto Fuentes, Juan Carlos
  • Espinoza, J.
  • Sket, Federico
  • Rodríguez Martínez, José Antonio
In this paper, we have developed and demonstrated a novel high-velocity impact experiment to study dynamic fragmentation of additively-manufactured metals. The experiment consists of a light-gas gun that fires a conical nosed cylindrical projectile, that impacts axially on a thin-walled cylindrical tube fabricated by 3D printing. The diameter of the cylindrical part of the projectile is approximately twice greater than the inner diameter of the cylindrical target, which is expanded as the projectile moves forward, and eventually breaks into fragments. The experiments have been performed for impact velocities ranging from ≈ 180 m∕s to ≈ 390 m∕s, leading to strain rates in the cylindrical target that vary between ≈ 9000 s-1 and ≈ 23500 s−1. The cylindrical samples tested are printed by Selective Laser Melting out of aluminum alloy AlSi10Mg, using two printing qualities, with two different outer diameters, 12 mm and 14 mm, and two different wall thicknesses, 1 mm and 2 mm. A salient feature of this work is that we have characterized by X-ray tomography the porous microstructure of selected specimens before testing. Three-dimensional analysis of the tomograms has shown that the initial void volume fraction of the printed cylinders varies between 1.9% and 6.1%, and the maximum equivalent diameter of the 10 largest pores ranges from 143 μm to 216 μm, for the two different printing conditions. Two high-speed cameras have been used to film the experiments and thus to obtain time-resolved information on the mechanics of formation and propagation of fractures. Moreover, fragments ejected from the samples have been recovered, sized, weighted and analyzed using X-ray tomography, so that we have obtained indications on the effect of porous microstructure, specimen dimensions and loading velocity on the number and distribution of fragment sizes. To the authors’ knowledge, this is the first paper (i) providing a systematic experimental study (34 impact tests) on the fragmentation behavior of printed specimens, and (ii) including 3D reconstructions of dynamic cracks in porous additively-manufactured materials., The research leading to these results has received funding from the European Research Council (ERC) under the European Union’s Horizon 2020 research and innovation programme (Project PURPOSE), grant agreement No. 758056. J.C. Nieto-Fuentes acknowledges support from the CONEX-Plus programme funded by Universidad Carlos III de Madrid and the European Union’s Horizon 2020 research and innovation programme , under the Marie Sklodowska-Curie grant agreement No. 801538.
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publication Artículo científico (JournalArticle)

Dynamics of necking and fracture in ductile porous materials

  • Zheng, Xinzhu
  • N Souglo, Komi Espoir
  • Rodríguez-Martínez, José A.
  • Srivastava, Ankit
The onset of necking in dynamically expanding ductile rings is delayed due to the stabilizing effect of inertia, and with increasing expansion velocity, both the number of necks incepted and the number of fragments increase. In general, neck retardation is expected to delay fragmentation as necking is often the precursor to fracture. However, in porous ductile materials, it is possible that fracture can occur without significant necking. Thus, the objective of this work is to unravel the complex interaction of initial porosity and inertia on the onset of necking and fracture. To this end, we have carried out a series of finite element calculations of unit cells with sinusoidal geometric perturbations and varying levels of initial porosity under a wide range of dynamic loading conditions. In the calculations, the material is modeled using a constitutive framework that includes many of the hardening and softening mechanisms that are characteristics of ductile metallic materials, such as strain hardening, strain rate hardening, thermal softening, and damage-induced softening. The contribution of the inertia effect on the loading process is evaluated through a dimensionless parameter that combines the effects of loading rate, material properties, and unit cell size. Our results show that low initial porosity levels favor necking before fracture, and high initial porosity levels favor fracture before necking, especially at high loading rates where inertia effects delay the onset of necking. The finite element results are also compared with the predictions of linear stability analysis of necking instabilities in porous ductile materials., J.A.R.-M. acknowledges the financial support provided by the European Research Council under the European Union's Horizon 2020 research and innovation programme (Project PURPOSE, Grant agreement 758056).
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publication Artículo científico (JournalArticle)

A three-pronged approach to predict the effect of plastic orthotropy on the formability of thin sheets subjected to dynamic biaxial stretching

  • N Souglo, Komi Espoir
  • Jacques, N.
  • Rodríguez-Martínez, José A.
In this paper, we have investigated the effect of material orthotropy on the formability of metallic sheets subjected to dynamic biaxial stretching. For that purpose, we have devised an original three-pronged methodology which includes a linear stability analysis, a nonlinear two-zone model and finite element calculations. We have studied 5 different materials whose mechanical behavior is described with an elastic isotropic, plastic anisotropic constitutive model with yielding based on Hill (1948) criterion. The linear stability analysis and the nonlinear two-zone model are extensions of the formulations developed by Zaera et al. (2015) and Jacques (2020), respectively, to consider Hill (1948) plasticity. The finite element calculations are performed with ABAQUS/Explicit (2016) using the unit-cell model developed by Rodríguez-Martínez et al. (2017), which includes a sinusoidal spatial imperfection to favor necking localization. The predictions of the stability analysis and the two-zone model are systematically compared against the finite element results – which are considered as the reference approach to validate the theoretical models – for loading paths ranging from plane strain stretching to equibiaxial stretching, and for different strain rates ranging from 100 s-1 to 50000 s-1 . The stability analysis and the two-zone model yield the same overall trends obtained with the finite element simulations for the 5 materials investigated, and for most of the strain rates and loading paths the agreement for the necking strains is also quantitative. Notably, the differences between the finite element results and the two-zone model rarely go beyond 5%. Altogether, the results presented in this work provide new insights into the mechanisms which control dynamic formability of anisotropic metallic sheets., The research leading to these results has received funding from the European Research Council (ERC) under the European Union’s Horizon 2020 research and innovation programme. Project PURPOSE, grant agreement 758056.
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publication Artículo científico (JournalArticle)

Finite element analysis to determine the role of porosity in dynamic localization and fragmentation: Application to porous microstructures obtained from additively manufactured materials

  • Marvi Mashhadi, Mohammad
  • Vaz-Romero, Álvaro
  • Sket, Federico
  • Rodríguez Martínez, José Antonio
In this paper, we have performed a microstructurally-informed finite element analysis on the effect of porosity on the formation of multiple necks and fragments in ductile thin rings subjected to dynamic expansion. For that purpose, we have characterized by X-ray tomography the porous microstructure of 4 different additively manufactured materials (aluminium alloy AlSi10Mg, stainless steel 316L, titanium alloy Ti6Al4V and Inconel 718L) with initial void volume fractions ranging from ≈0.0007% to ≈ 2%, and pore sizes varying between ≈ 6 μm and ≈110 μm. Three-dimensional analysis of the tomograms has revealed that the voids generally have nearly spherical shape and quite homogeneous spatial distribution in the bulk of the four materials tested. The pore size distributions quantified from the tomograms have been characterized using a Log-normal statistical function, which has been used in conjunction with a Force Biased Algorithm that replicates the experimentally observed random spatial distribution of the voids, to generate ring expansion finite element models in ABAQUS/Explicit (2016) which include actual porous microstructures representative of the materials tested. We have modeled the materials behavior using von Mises plasticity, and we have carried out finite element calculations for both elastic perfectly-plastic materials, and materials which show strain hardening, strain rate hardening and temperature softening effects. Moreover, we have assumed that fracture occurs when a critical value of effective plastic strain is reached. The finite element calculations have been performed for expansion velocities ranging from 50 m/s to 500 m/s. A key point of this investigation is that we have established individualized correlations between the main features of the porous microstructure (i.e. initial void volume fraction, average void size and maximum void size) and the number of necks and fragments formed in the calculations. In addition, we have brought out the effect of the porous microstrucure and inertia on the distributions of neck and fragment sizes. To the authors’ knowledge, this is the first paper ever considering actual porous microstructures to investigate the role of material defects in multiple localization and dynamic fragmentation of ductile metallic materials., The research leading to these results has received funding from the European Research Council (ERC) under the European Union's Horizon 2020 research and innovation programme. Project PURPOSE, grant agreement 758056.
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publication Artículo científico (JournalArticle)

Theoretical predictions of dynamic necking formability of ductile metallic sheets with evolving plastic anisotropy and tension-compression asymmetry

  • Murlidhar, Anil Kumar
  • N Souglo, Komi Espoir
  • Hosseini, Navab
  • Rodríguez-Martínez, José A.
In this paper, we have investigated necking formability of anisotropic and tension-compression asymmetric metallic sheets subjected to in-plane loading paths ranging from plane strain tension to near equibiaxial tension. For that purpose, we have used three different approaches: a linear stability analysis, a nonlinear two-zone model and unit-cell finite element calculations. We have considered three materials –AZ31-Mg alloy, high purity α-titanium and OFHC copper– whose mechanical behavior is described with an elastic-plastic constitutive model with yielding defined by the CPB06 criterion (15) which includes specific features to account for the evolution of plastic orthotropy and strength differential effect with accumulated plastic deformation (48). From a methodological standpoint, the main novelty of this paper with respect to the recent work of N’souglo et al. (42) –which investigated materials with yielding described by the orthotropic criterion of Hill (24)– is the extension of both stability analysis and nonlinear two-zone model to consider anisotropic and tension-compression asymmetric materials with distortional hardening. The results obtained with the stability analysis and the nonlinear two-zone model show reasonable qualitative and quantitative agreement with forming limit diagrams calculated with the finite element simulations, for the three materials considered, and for a wide range of loading rates varying from quasi-static loading up to 40000 s− 1, which makes apparent the capacity of the theoretical models to capture the mechanisms which control necking formability of metallic materials with complex plastic behavior. Special mention deserves the nonlinear two-zone model, as it does not need prior calibration –unlike the stability analysis– and it yields accurate predictions that rarely deviate more than 10% from the results obtained with the unit-cell calculations., Funding Open Access funding provided thanks to the CRUE-CSIC agreement with Springer Nature. The research leading to these results has received funding from the European Research Council (ERC) under the European Union's Horizon 2020 research and innovation programme. Project PURPOSE, grant agreement 758056.
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publication Artículo científico (JournalArticle)

A comparative study of the dynamic fragmentation of non-linear elastic and elasto-plastic rings: the roles of stored elastic energy and plastic dissipation

  • Vaz-Romero, Álvaro
  • Mercier, Sebastien
  • Rodríguez-Martínez, José A.
  • Molinari, Alain Louis
We develop a comparative analysis of the processes of dynamic necking and fragmentation in elasto-plastic and hyperelastic ductile rings subjected to rapid radial expansion. For that purpose, finite element simulations have been carried out using the commercial code ABAQUS/Explicit. Expanding velocities which range between 25 and 600 m/s have been investigated. The elasto-plastic material and the hyperelastic material are modelled with constitutive equations which provide nearly the same stress-strain response during monotonic uniaxial tensile loading, and fracture is assumed to occur at the same level of deformation energy. The computations have revealed that, while the number of necks nucleated in the elasto-plastic and hyperelastic rings is similar, the mechanisms which control their development are significantly different. In the elasto-plastic rings several necks are arrested due to the stress waves which travel the specimen after the localization process has started, and thus the number of fractures in the ring is significantly lower than the number of incepted necks. On the contrary, these stress waves do not stop the development of any neck in the hyperelastic rings. The elastic energy released from the sections of the ring which are unloading during the localization process fuels the development of the necks. Hence, for the whole range of investigated velocities, the proportion of necks that develop into fracture sites is much greater for the hyperelastic rings than for the elasto-plastic ones. The comparison between the numerical results obtained for both materials brings to light the roles of elastic unloading and plastic dissipation in multiple necking and fragmentation processes., AM and JARM acknowledge the support by the French State through the program Investment in the future operated by the National Research Agency (ANR) and referenced by ANR-11-LABX-0008-01 (LabEx DAMAS). AVR acknowledges the nancial support obtained from the University Carlos III of Madrid through the programme Ayudas para la movilidad - Convocatoria 2017. The research leading to these results has received funding from the European Research Council (ERC) under the European Union's Horizon 2020 research and innovation programme. Project PURPOSE, grant agreement 758056.
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publication Artículo científico (JournalArticle)

New insights into the role of porous microstructure on dynamic shear localization

  • Ambikadevi Rajasekharan Nair, Vishnu
  • Marvi Mashhadi, Mohammad
  • Nieto Fuentes, Juan Carlos
  • Rodríguez Martínez, José Antonio
This paper provides new insights into the role of porous microstructure on dynamic shear localization. For that purpose, we have performed 3D finite element calculations of electromagnetically collapsing thick-walled cylinders. The geometry and dimensions of the cylindrical specimens are taken from the experiments of Lovinger et al. (2015), and the loading and boundary conditions from the 2D simulations performed by Lovinger et al. (2018). The mechanical behavior of the material is modeled as elastic-plastic, with yielding described by the von Mises criterion, an associated flow rule and isotropic hardening/softening, being the flow stress dependent on strain, strain rate and temperature. Moreover, plastic deformation is considered to be the only source of heat, and the analysis accounts for the thermal conductivity of the material. The distinctive feature of this work is that we have followed the methodology developed by Marvi-Mashhadi et al. (2021) to incorporate into the finite element calculations the actual porous microstructure of 4 different additively manufactured materials –aluminium alloy AlSi10Mg, stainless steel 316L, titanium alloy Ti6Al4V and Inconel 718– for which the initial void volume fraction varies between 0.001% and 2%, and the pores size ranges from ≈ 6 μm to ≈ 110 μm. The numerical simulations have been performed using the Coupled Eulerian-Lagrangian approach available in ABAQUS/Explicit (2016), which allows to capture the shape evolution, coalescence and collapse of the voids at large strains. To the authors’ knowledge, this paper contains the first finite element simulations with explicit representation of the material porosity which demonstrate that voids promote dynamic shear localization, acting as preferential sites for the nucleation of the shear bands, speeding up their development, and tailoring their direction of propagation. In addition, the numerical calculations bring out that for a given void volume fraction more shear bands are nucleated as the number of voids increases, while the shear bands are incepted earlier and develop faster as the size of the pores increases., The research leading to these results has received funding from the European Research Council (ERC) under the European Union’s Horizon 2020 research and innovation programme. Project PURPOSE, grant agreement 758056.
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publication Artículo científico (JournalArticle)

The combined effect of size, inertia and porosity on the indentation response of ductile materials

  • Santos, T. dos
  • Srivastava, Ankit
  • Rodríguez-Martínez, José A.
Herein, we present a self-similar cavity expansion model that follows from the work of Cohen and Durban (2013b) to analyze the dynamic indentation response of elasto-plastic porous materials while accounting for the plastic strain gradient induced size effect. The incorporation of the plastic strain gradient induced size effect in the dynamic cavity expansion model for elasto-plastic porous materials is the key novelty of our model. The material hardness predicted using the cavity expansion model for a wide range of indentation depths and speeds is compared against the available experimental results for OFHC copper, for strain rates varying from 10−4 s−1 to 108 s−1. We note that despite several simplifying assumptions, the predictions of our cavity expansion model show a reasonable agreement with the experimentally measured material hardness over a wide range of indentation depths and speeds. In addition, we have also carried out parametric analysis to elucidate the specific roles of indentation speed, size effect and initial porosity, on the material hardness and cavitation fields that develop during the indentation process. In particular, our parametric analysis shows that there exists a critical value of the indentation speed beyond which the contribution of inertial effect becomes extremely important and the material hardness increases rapidly. While the influence of the initial porosity on the material hardness is found to increase with increasing indentation speed and decrease with increasing size effect., TdS wishes to acknowledge the support of FAPERGS, Fundação de Amparo ã Pesquisa do Estado do Rio Grande do Sul, grant agreement 19/2551 − 0001054 − 0. JAR-M acknowledges the financial support obtained from the European Research Council (ERC) under the European Union’s Horizon 2020 research and innovation programme. Project PURPOSE, grant agreement 758056.
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publication Artículo científico (JournalArticle)

Shear band formation in porous thin-walled tubes subjected to dynamic torsion

  • Ambikadevi Rajasekharan Nair, Vishnu
  • Nieto Fuentes, Juan Carlos
  • Rodríguez-Martínez, José A.
In this paper, we have performed 3D finite element calculations of thin-walled tubes subjected to dynamic twisting to investigate the effect of porous microstructure on the formation of shear localization bands under simple shear conditions. For that purpose, we have incorporated into the finite element model the porous microstructures of four different additive manufactured metals – aluminium alloy AlSi10Mg, stainless steel 316L, titanium alloy Ti6Al4V and Inconel 718 – for which the void volume fraction varies from ≈ 0.001% to ≈ 2 %, and the voids size between ≈ 6 μm and ≈ 110 μm (Marvi-Mashhadi et al., 2021). For each microstructure, we have created up to 10 realizations varying the spatial location of the voids and the distribution of voids size. The matrix material is elastic/plastic, with yielding defined by the von Mises yield criterion and associated flow rule. The yield stress evolution is considered to be dependent on strain, strain rate and temperature, with parameters corresponding to Titanium and HY-100 Steel, taken from Molinari (1997) and Batra and Kim (1990), respectively. Moreover, we have assumed the deformation process to be adiabatic. The calculations have been performed for shear strain rates ranging from 100 s−1 to 10000 s−1. To the authors’ knowledge, this is the first study ever that simulates dynamic torsion testing of porous materials with actual representation of voids, providing new results which bring to light the influence of porosity on dynamic shear banding under simple shearing. Namely, the numerical calculations have shown that both the location of the shear band and the critical strain leading to the shear band formation depend on the spatial and size distribution of the voids in the specimen, evidencing the influence of material defects on the localization pattern. Notably, the shear band nucleation strain decreases with both the void volume fraction in the specimen and the size of the voids, the size of the largest pore being the main microstructural feature controlling the loss of load carrying capacity of the specimen. In addition, we have carried out a parametric analysis varying the temperature and strain rate sensitivities of the material, and the loading rate. For the strain rates investigated, increasing the loading speed leads to a mild decrease of the shear strain leading to shear band formation, while the strain rate sensitivity is shown to stabilize material behavior and delay localization. Moreover, the numerical results have made apparent that for the hardening materials considered, thermal softening is essential to trigger the shear band formation, so that the porous microstructure alone does not lead to shear localization., The research leading to these results has received funding from the European Research Council (ERC) under the European Union's Horizon 2020 research and innovation programme. Project PURPOSE, grant agreement 758056. J. C. Nieto-Fuentes acknowledges support from the CONEX-Plus programme funded by Universidad Carlos III de Madrid, Spain and the European Union's Horizon 2020 research and innovation programme, under the Marie Sklodowska-Curie grant agreement 801538.
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publication Artículo científico (JournalArticle)

High-speed fragmentation of porous metal rings

  • Kumar, M. A.
  • Virazels, Thomas
  • García Molleja, J.
  • Sket, Federico
  • Rodríguez Martínez, José Antonio
  • Ravi Chandar, K.
In this paper, we have conducted dynamic ring expansion tests on 3D-printed AlSi10Mg porous samples utilizing both electromagnetic and mechanical testing techniques. The electromagnetic loading setup developed by Zhang and Ravi-Chandar (2006, 2008) is employed as a benchmark for evaluating and comparing the performance of the experimental configuration recently pro-posed by Nieto-Fuentes et al. (2023) to investigate the fragmentation of metallic rings using a pneumatic launcher. A total of 67 experiments have been carried out covering a wide range of strain rates from 2200 s−1 to 16300 s−1. The tests performed with both experimental techniques were imaged using high-speed cameras to obtain time-resolved information on the mechanics of sample deformation and fragmentation. The recorded data allowed us to determine the number of fragments, the elongation of the specimens at the onset of fracture, and the fragmentation time. Moreover, the fragments ejected from the samples have been soft recovered, measured, and weighed. A good correlation is observed between the results obtained from electromagnetic and mechanical loading setups regarding the fragments size distribution and the evolution of the number of fragments with the loading rate. This agreement serves as a robust validation for the experimental configuration put forth by Nieto-Fuentes et al. (2023), which allowed reaching higher strain rates than the setup of Zhang and Ravi-Chandar (2006, 2008), and it is notable for its simplicity, fast operation, and quick assembly. In addition, scanning electron microscopy and X-ray tomography analysis performed on recovered fragments from tests conducted at different expansion velocities with both testing techniques has provided indications on the evolution of the porous microstructure of the material at high strain rates, showing that the porosity of 3D-printed AlSi10Mg is instrumental for the propagation of cracks leading to the fragmentation of the rings. Moreover, fractography analysis of the crack surfaces revealed that while the fractures occurred without the preceding formation of necks, yet the fracture at the microscopic level was essentially ductile. The influence of the porous microstructure on the fragmentation mechanisms has been further investigated through finite element simulations that incorporate the voids’ size distribu-tion of the specimens obtained from X-ray tomography analysis (Marvi-Mashhadi et al., 2021). The numerical results have demonstrated both quantitative and qualitative agreement with the experiments, showing that large pores and clusters favor stress concentration and subsequent fracture initiation and progression. Consistent with the statistical fragmentation theory of Mott (1947) for elastic-plastic materials that break without previous necking, the release waves emanating from the large pore defects and early fractures seem to play a critical role in determining the scale of the fragment size distribution in printed AlSi10Mg specimens., The research leading to these results has received funding from the European Research Council (ERC) under the European Union’s Horizon 2020 research and innovation programme. Project PURPOSE, grant agreement 758056.