Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 26
Encontrada(s) 1 página(s)

UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Quality of transmission estimator retraining for dynamic optimization in optical networks

  • Mahajan, Ankush
  • Christodoulopoulos, Konstantinos
  • Martínez Rivera, Ricardo Victor
  • Muñoz González, Raül
  • Spadaro, Salvatore|||0000-0002-4100-1726
Optical network optimization involves an algorithm and a physical layer model (PLM) to estimate the quality of transmission of connections while examining candidate optimization operations. In particular, the algorithm typically calculates intermediate solutions until it reaches the optimum, which is then configured to the network. If it uses a PLM that was aligned once to reflect the starting network configuration, then the algorithm within its intermediate calculations can project the network into states where the PLM suffers from low accuracy, resulting in a suboptimal optimization. In this paper, we propose to solve dynamic multivariable optimization problems with an iterative closed control loop process, where after certain algorithm steps we configure the intermediate solution so that we monitor and realign/retrain the PLM to follow the projected network states. The PLM is used as a digital twin, a digital representation of the real system, which is realigned during the dynamic optimization process. Specifically, we study the dynamic launch power optimization problem, where we have a set of established connections, and we optimize their launch powers while the network operates. We observed substantial improvements in the sum and the lowest margin when optimizing the launch powers with the proposed approach over optimization using a one-time trained PLM. The proposed approach achieved near-to-optimum solutions as found by optimizing and continuously probing and monitoring the network, but with a substantial lower optimization time., Funding: Horizon 2020 Framework Programme (765275). This work is a part of the Future Optical Networks for Innovation, Research and Experimentation (ONFIRE) project (https://h2020-onfire.eu/), supported by the European Union’s Horizon 2020 Research and Innovation Programme under the Marie Skłodowska-Curie Actions., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Contribución de congreso (ConferenceOutput)

Modeling filtering penalties in ROADM-based networks with machine learning for QoT estimation

  • Mahajan, Ankush
  • Christodoulopoulos, Konstantinos
  • Martinez, Ricardo
  • Spadaro, Salvatore|||0000-0002-4100-1726
  • Muñoz, Raul
© 2020 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., Monitoring 3dB bandwidth and other spectrum related parameters at ROADMs provides information about quality of their filters. We propose a machine-learning model to estimate end-to-end filtering penalty for more accurate QoT estimation of future connections., Authors would like to thank Karsten Schuh and Camille Delezoide of Nokia Bell Labs for technical discussionsonfilter modelling. This work is a part ofH2020-MSCA, ONFIRE project supported by EU, grant agreement No. 765275., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Spectral processing techniques for efficient monitoring in optical networks

  • Locatelli, Fabiano|||0000-0002-2971-1303
  • Christodoulopoulos, Konstantinos
  • Svaluto Moreolo, Michela
  • Fàbrega Sánchez, Josep Maria
  • Nadal Reixats, Laia
  • Spadaro, Salvatore|||0000-0002-4100-1726
Having ubiquitous optical monitors in dense wavelength-division multiplexing (DWDM) or flex-grid networks allows the estimation in real time of crucial parameters. Such monitoring would be even more important in disaggregated optical networks, to inspect performance issues related to inter-vendor interoperability. Several important parameters can be retrieved using optical spectrum analyzers (OSAs). However, omnipresent OSAs represent an infeasible solution. Nevertheless, the advent of new, relatively cheap, compact and medium-resolution optical channel monitors (OCMs) enable a more intensive deployment of these devices. In this paper, we identify two main scenarios for the placement of such monitors: at the ingress and at the egress of the optical nodes. In the ingress scenario, we can directly estimate the parameters related to the signals, but not those related to the filters. On the contrary, in the egress scenario, the filter-related parameters can be easily detected, but not those related to amplified spontaneous emission. Therefore, we present two methods that, leveraging a curve fitting and a machine learning regression algorithm, allow detection of the missing parameters. We verify the proposed solutions with spectral data acquired in simulation and experimental setups. We obtained good estimation accuracy for both setups and for both studied placement scenarios. It is noteworthy that in the experimental assessment of the ingress scenario, we achieved a maximum absolute error (MAE) lower than 1 GHz in filter bandwidth estimation and a MAE lower than 0.5 GHz in filter frequency shift estimation. In addition, by comparing the relative errors of the considered parameters, we identified the ingress scenario as the more beneficial. In particular, we estimated the filter central frequency shift with 84% and the filter 6 dB bandwidth with 75% higher accuracy, with respect to datasheet/reference values. This translates into a total reduction of the estimated signal-to-noise ratio (SNR) penalty, introduced by a single optical filter, of 0.24 dB., Funding: Horizon 2020 Framework Programme (765275). This work is part of the Future Optical Networks for Innovation, Research and Experimentation (ONFIRE) project (https://h2020-onfire.eu), which is supported by the European Union’s Horizon 2020 Research and Innovation Programme under the Marie Skłodowska-Curie Action., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Contribución de congreso (ConferenceOutput)

Adaptive and iterative QoT estimator retraining for launch power optimization

  • Mahajan, Ankush
  • Christodoulopoulos, Konstantinos
  • Martínez Rivera, Ricardo Victor
  • Muñoz González, Raül
  • Spadaro, Salvatore|||0000-0002-4100-1726
We dynamically optimize the transponders launch powers with iterative closed control loops. We close the loop after an adaptable number of algorithm’s intermediate calculations, to monitor and retrain the QoT estimator with the real world., This work is a part of H2020-MSCA, ONFIRE project supported by EU, grant agreement No. 765275., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Machine learning-based in-band OSNR estimation from optical spectra

  • Locatelli, Fabiano|||0000-0002-2971-1303
  • Christodoulopoulos, Konstantinos
  • Svaluto Moreolo, Michela
  • Fàbrega, Josep Maria
  • Spadaro, Salvatore|||0000-0002-4100-1726
© 2019 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., Measuring the optical signal to noise ratio (OSNR) at certain network points is essential for failure handling, for single connection but also global network optimization. Estimating OSNR is inherently difficult in dense wavelength routed networks, where connections accumulate noise over different paths and tight filters do not allow the observation of the noise level at signal sides. We propose an in-band OSNR estimation process, which relies on a machine learning (ML) method, in particular on Gaussian process (GP) or support vector machine (SVM) regression. We acquired high-resolution optical spectra, through an experimental setup, using a Brillouin optical spectrum analyzer (BOSA), on which we applied our method and obtained excellent estimation accuracy. We also verified the accuracy of this approach for various resolution scenarios. To further validate it, we generated spectral data for different configurations and resolutions through simulations. This second validation confirmed the estimation quality of the proposed approach., The authors would like to thank Aragon Photonics Labs for providing the BOSA used for the experiments. This work was partially funded by the ONFIRE project supported by EU Horizon 2020 research and innovation programme under the Marie Skłodowska-Curie grant agreement No. 765275, Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Contribución de congreso (ConferenceOutput)

Modelling multi-vendor transponders performance and optimizing launch power

  • Mahajan, Ankush
  • Christodoulopoulos, Konstantinos
  • Martínez Rivera, Ricardo Victor
  • Spadaro, Salvatore|||0000-0002-4100-1726
  • Muñoz González, Raül
We propose physical layer model extensions that capture the performance variations of multivendor transponders and use those with appropriate algorithms to optimize connections’ launch powers. We estimated potential SNR improvements upto ~35% for 4 different vendors in a network of 27 nodes., This work is a part of ONFIRE project supported by EU Horizon 2020 research and innovation programme under the MSCA grant agreement No. 765275., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Contribución de congreso (ConferenceOutput)

Experimental demonstration of a machine learning-based in-band OSNR estimator from optical spectra

  • Locatelli, Fabiano|||0000-0002-2971-1303
  • Christodoulopoulos, Konstantinos
  • Fàbrega, Josep Maria
  • Svaluto Moreolo, Michela
  • Nadal, Laia
  • Spadaro, Salvatore|||0000-0002-4100-1726
Channel spectral monitors are becoming a cost effective solution to improve the management, resiliency and efficiency of next generation optical transport networks. We experimentally demonstrate a technique based on machine learning (ML) for the in-band estimation of amplified spontaneous emission (ASE) noise and filter 3-dB bandwidth, using optical spectra acquired after the reconfigurable optical add/drop multiplexers (ROADMs) filters. We assess the performance of the proposed method, considering laser drift and filters bandwidth tightening scenarios, showing quite good estimation accuracy under such conditions., This work was partially funded by the ONFIRE project supported by EU Horizon 2020 research and innovation programme under the Marie Skłodowska-Curie grant agreement No. 765275, Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Contribución de congreso (ConferenceOutput)

Improving QoT estimation accuracy with DGE monitoring using machine learning

  • Mahajan, Ankush
  • Christodoulopoulos, Konstantinos
  • Martinez, Ricardo
  • Spadaro, Salvatore|||0000-0002-4100-1726
  • Muñoz, Raul
In optical transport networks, Dynamic Gain Equalizers (DGE) are typically used at each link. A DGE selectively attenuates the channels to compensate the cumulative Erbium Doped Fiber Amplifier (EDFA) gain ripple effect on the multi-span link, resulting in almost flat output power at the end of the link. We leverage monitored per link DGE attenuation profiles and coherent receivers Signal to Noise Ratio (SNR) information, and propose a machine learning (ML) based scheme to estimate the EDFA gain ripple penalties for new connections. Using that in realistic simulation scenarios we observed a design margin reduction from ~1dB to ~0.3dBs., This work is a part of Future Optical Networks for Innovation, Research andExperimentation, ONFIRE project supported by European Union’s fundedHorizon 2020 research and innovation programme under the MarieSkłodowska-Curie grant agreement No. 765275., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Modeling EDFA gain ripple and filter penalties with machine learning for accurate QoT estimation

  • Mahajan, Ankush
  • Christodoulopoulos, Konstantinos
  • Martínez, Ricardo
  • Spadaro, Salvatore|||0000-0002-4100-1726
  • Muñoz, Raul
© 2020 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., For reliable and efficient network planning and operation, accurate estimation of Quality of Transmission (QoT) before establishing or reconfiguring the connection is necessary. In optical networks, a design margin is generally included in a QoT estimation tool (Qtool) to account for modeling and parameter inaccuracies, ensuring the acceptable performance. In this work, we use monitoring information from an operating network combined with supervised machine learning (ML) techniques to understand the network conditions. In particular, we model the penalties generated due to i.) Erbium Doped Fiber Amplifier (EDFA) gain ripple effect, and ii.) filter spectral shape uncertainties at Reconfigurable Optical Add and Drop Multiplexer (ROADM) nodes. Enhancing the Qtool with the proposed ML regression models yields estimates for new or reconfigured connections that account for these two effects, resulting in more accurate QoT estimation and a reduced design margin. We initially propose two supervised ML regression models, implemented with Support Vector Machine Regression (SVMR), to estimate the individual penalties of the two effects and then a combined model. On Deutsche Telekom (DT) network topology with 12 nodes and 40 bidirectional links, we achieve a design margin reduction of ~1dB for new connection requests., This work was supported by the Future Optical Networks for Innovation, Research and Experimentation, ONFIRE project Euro-pean Union’s funded Horizon 2020 research and innovation programme underthe Marie Skłodowska-Curie under Grant 765275., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Contribución de congreso (ConferenceOutput)

Filter features extraction from optical spectra

  • Locatelli, Fabiano|||0000-0002-2971-1303
  • Christodoulopoulos, Konstantinos
  • Fàbrega Sánchez, Josep Maria
  • Svaluto Moreolo, Michela
  • Nadal Reixats, Laia
  • Spadaro, Salvatore|||0000-0002-4100-1726
We propose a method to estimate the central frequency and the bandwidth of optical filters, that relies on optical spectra captured with optical channel monitors at ROADM’s ingress port. We demonstrate for both features high estimation accuracy using simulated and experimental data., This work was funded by the ONFIRE project supported by the EU Horizon 2020 research and innovation programme under the Marie Skłodowska-Curie grant agreement No. 765275., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Impact of multi-vendor transponders performance on design margin in optical networks

  • Mahajan, Ankush
  • Christodoulopoulos, Konstantinos
  • Martínez, Ricardo
  • Muñoz, Raul
  • Spadaro, Salvatore|||0000-0002-4100-1726
For reliable and efficient network planning and operation, accurate estimation of Quality of Transmission (QoT) is necessary. In optical networks, a physical layer model (PLM) is typically used as a QoT estimation tool (Qtool) including a design margin to account for modeling and parameter inaccuracies, to ensure acceptable performance. Such margin also covers the performance variations of the transponders (TPs) which are relatively low in a single vendor environment. However, for disaggregated networks that utilize TPs from multiple vendors, such as partial disaggregated networks with open line system (OLS), this traditional approach limits the Qtool estimation accuracy. Although higher TP performance variations can be covered with an additional margin, this approach would reduce the efficiency and consume the benefits of disaggregation. Therefore, we propose PLM extensions that capture the performance variations of multi- vendor TPs. In particular, we propose four TP vendor dependent performance factors and we also devise a Machine Learning (ML) scheme to learn these performance factors in offline and online network planning scenarios. The proposed extended PLM and ML training scheme are evaluated through realistic simulations. Results show a design margin reduction of greater than 1 dB for new connection requests in a disaggregated network with TPs from four vendors. On top of this, the results also show a ~0.5 dB additional Signal to Noise Ratio (SNR) saving for new connection requests by proper selection of the TPs., This work is a part of the Future Optical Networks for Innovation, Research and Experimentation (ONFIRE) Project (Project ID-765275)., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Contribución de congreso (ConferenceOutput)

Data plane elements for optical performance monitoring agnostic to the modulation format for disaggregated optical networks

  • Fàbrega Sánchez, Josep Maria
  • Locatelli, Fabiano|||0000-0002-2971-1303
  • Nadal Reixats, Laia
  • Christodoulopoulos, Konstantinos
  • Svaluto Moreolo, Michela
  • Spadaro, Salvatore|||0000-0002-4100-1726
In this paper, data plane alternatives for optical performance monitoring are presented as enablers to address the key challenges in disaggregated optical networks. In fact, a key element of the disaggregated networks is optical performance monitoring that is expected to deliver the feedback needed by the control plane to guarantee end-to-end quality of transmission and quality of service. Therefore, we will discuss data plane elements for non-intrusive monitoring agnostic to the modulation format, proposing and analyzing different schemes. Furthermore, we will also review the relevant figures of merit to be delivered to the /SDN/ control, orchestration and management planes and their potential impact on the network performance., This work was supported by the Spanish MINECO project AURORAS (RTI2018-099178-B-I00) and EU-H2020 project ONFIRE (G.A. 765275)., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Contribución de congreso (ConferenceOutput)

Machine learning assisted EDFA gain ripple modelling for accurate QoT estimation

  • Mahajan, Ankush
  • Christodoulopoulos, Konstantinos
  • Martínez Rivera, Ricardo Victor
  • Spadaro, Salvatore|||0000-0002-4100-1726
  • Muñoz González, Raül
Wavelength dependent EDFA gain ripple has an impact on connection's OSNR performance. We propose a machine learning regression model to estimate the end to end gain ripple penalty and to increase QoT estimation accuracy., This work is a part of ONFIRE project supported by EU Horizon 2020 research and innovation programme under the Marie Skłodowska-Curie grant agreement No. 765275., Peer Reviewed
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Machine learning assisted EDFA gain ripple modelling for accurate QoT estimation

  • Mahajan, Ankush
  • Christodoulopoulos, Konstantinos
  • Martínez Rivera, Ricardo Victor
  • Spadaro, Salvatore
  • Muñoz González, Raül
Wavelength dependent EDFA gain ripple has an impact on connection's OSNR performance. We propose a machine learning regression model to estimate the end to end gain ripple penalty and to increase QoT estimation accuracy., This work is a part of ONFIRE project supported by EU Horizon 2020 research and innovation programme under the Marie Skłodowska-Curie grant agreement No. 765275., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Improving QoT estimation accuracy with DGE monitoring using machine learning

  • Mahajan, Ankush
  • Christodoulopoulos, Konstantinos
  • Martinez, Ricardo
  • Spadaro, Salvatore
  • Muñoz, Raul
In optical transport networks, Dynamic Gain Equalizers (DGE) are typically used at each link. A DGE selectively attenuates the channels to compensate the cumulative Erbium Doped Fiber Amplifier (EDFA) gain ripple effect on the multi-span link, resulting in almost flat output power at the end of the link. We leverage monitored per link DGE attenuation profiles and coherent receivers Signal to Noise Ratio (SNR) information, and propose a machine learning (ML) based scheme to estimate the EDFA gain ripple penalties for new connections. Using that in realistic simulation scenarios we observed a design margin reduction from ~1dB to ~0.3dBs., This work is a part of Future Optical Networks for Innovation, Research andExperimentation, ONFIRE project supported by European Union’s fundedHorizon 2020 research and innovation programme under the MarieSkłodowska-Curie grant agreement No. 765275., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Modeling filtering penalties in ROADM-based networks with machine learning for QoT estimation

  • Mahajan, Ankush
  • Christodoulopoulos, Konstantinos
  • Martinez, Ricardo
  • Spadaro, Salvatore
  • Muñoz, Raul
© 2020 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., Monitoring 3dB bandwidth and other spectrum related parameters at ROADMs provides information about quality of their filters. We propose a machine-learning model to estimate end-to-end filtering penalty for more accurate QoT estimation of future connections., Authors would like to thank Karsten Schuh and Camille Delezoide of Nokia Bell Labs for technical discussionsonfilter modelling. This work is a part ofH2020-MSCA, ONFIRE project supported by EU, grant agreement No. 765275., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Experimental demonstration of a machine learning-based in-band OSNR estimator from optical spectra

  • Locatelli, Fabiano
  • Christodoulopoulos, Konstantinos
  • Fàbrega, Josep Maria
  • Svaluto Moreolo, Michela
  • Nadal, Laia
  • Spadaro, Salvatore
Channel spectral monitors are becoming a cost effective solution to improve the management, resiliency and efficiency of next generation optical transport networks. We experimentally demonstrate a technique based on machine learning (ML) for the in-band estimation of amplified spontaneous emission (ASE) noise and filter 3-dB bandwidth, using optical spectra acquired after the reconfigurable optical add/drop multiplexers (ROADMs) filters. We assess the performance of the proposed method, considering laser drift and filters bandwidth tightening scenarios, showing quite good estimation accuracy under such conditions., This work was partially funded by the ONFIRE project supported by EU Horizon 2020 research and innovation programme under the Marie Skłodowska-Curie grant agreement No. 765275, Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Quality of transmission estimator retraining for dynamic optimization in optical networks

  • Mahajan, Ankush
  • Christodoulopoulos, Konstantinos
  • Martínez Rivera, Ricardo Victor
  • Muñoz González, Raül
  • Spadaro, Salvatore
Optical network optimization involves an algorithm and a physical layer model (PLM) to estimate the quality of transmission of connections while examining candidate optimization operations. In particular, the algorithm typically calculates intermediate solutions until it reaches the optimum, which is then configured to the network. If it uses a PLM that was aligned once to reflect the starting network configuration, then the algorithm within its intermediate calculations can project the network into states where the PLM suffers from low accuracy, resulting in a suboptimal optimization. In this paper, we propose to solve dynamic multivariable optimization problems with an iterative closed control loop process, where after certain algorithm steps we configure the intermediate solution so that we monitor and realign/retrain the PLM to follow the projected network states. The PLM is used as a digital twin, a digital representation of the real system, which is realigned during the dynamic optimization process. Specifically, we study the dynamic launch power optimization problem, where we have a set of established connections, and we optimize their launch powers while the network operates. We observed substantial improvements in the sum and the lowest margin when optimizing the launch powers with the proposed approach over optimization using a one-time trained PLM. The proposed approach achieved near-to-optimum solutions as found by optimizing and continuously probing and monitoring the network, but with a substantial lower optimization time., Funding: Horizon 2020 Framework Programme (765275). This work is a part of the Future Optical Networks for Innovation, Research and Experimentation (ONFIRE) project (https://h2020-onfire.eu/), supported by the European Union’s Horizon 2020 Research and Innovation Programme under the Marie Skłodowska-Curie Actions., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Modeling EDFA gain ripple and filter penalties with machine learning for accurate QoT estimation

  • Mahajan, Ankush
  • Christodoulopoulos, Konstantinos
  • Martínez, Ricardo
  • Spadaro, Salvatore
  • Muñoz, Raul
© 2020 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., For reliable and efficient network planning and operation, accurate estimation of Quality of Transmission (QoT) before establishing or reconfiguring the connection is necessary. In optical networks, a design margin is generally included in a QoT estimation tool (Qtool) to account for modeling and parameter inaccuracies, ensuring the acceptable performance. In this work, we use monitoring information from an operating network combined with supervised machine learning (ML) techniques to understand the network conditions. In particular, we model the penalties generated due to i.) Erbium Doped Fiber Amplifier (EDFA) gain ripple effect, and ii.) filter spectral shape uncertainties at Reconfigurable Optical Add and Drop Multiplexer (ROADM) nodes. Enhancing the Qtool with the proposed ML regression models yields estimates for new or reconfigured connections that account for these two effects, resulting in more accurate QoT estimation and a reduced design margin. We initially propose two supervised ML regression models, implemented with Support Vector Machine Regression (SVMR), to estimate the individual penalties of the two effects and then a combined model. On Deutsche Telekom (DT) network topology with 12 nodes and 40 bidirectional links, we achieve a design margin reduction of ~1dB for new connection requests., This work was supported by the Future Optical Networks for Innovation, Research and Experimentation, ONFIRE project Euro-pean Union’s funded Horizon 2020 research and innovation programme underthe Marie Skłodowska-Curie under Grant 765275., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Data plane elements for optical performance monitoring agnostic to the modulation format for disaggregated optical networks

  • Fàbrega Sánchez, Josep Maria
  • Locatelli, Fabiano
  • Nadal Reixats, Laia
  • Christodoulopoulos, Konstantinos
  • Svaluto Moreolo, Michela
  • Spadaro, Salvatore
In this paper, data plane alternatives for optical performance monitoring are presented as enablers to address the key challenges in disaggregated optical networks. In fact, a key element of the disaggregated networks is optical performance monitoring that is expected to deliver the feedback needed by the control plane to guarantee end-to-end quality of transmission and quality of service. Therefore, we will discuss data plane elements for non-intrusive monitoring agnostic to the modulation format, proposing and analyzing different schemes. Furthermore, we will also review the relevant figures of merit to be delivered to the /SDN/ control, orchestration and management planes and their potential impact on the network performance., This work was supported by the Spanish MINECO project AURORAS (RTI2018-099178-B-I00) and EU-H2020 project ONFIRE (G.A. 765275)., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Impact of multi-vendor transponders performance on design margin in optical networks

  • Mahajan, Ankush
  • Christodoulopoulos, Konstantinos
  • Martínez, Ricardo
  • Muñoz, Raul
  • Spadaro, Salvatore
For reliable and efficient network planning and operation, accurate estimation of Quality of Transmission (QoT) is necessary. In optical networks, a physical layer model (PLM) is typically used as a QoT estimation tool (Qtool) including a design margin to account for modeling and parameter inaccuracies, to ensure acceptable performance. Such margin also covers the performance variations of the transponders (TPs) which are relatively low in a single vendor environment. However, for disaggregated networks that utilize TPs from multiple vendors, such as partial disaggregated networks with open line system (OLS), this traditional approach limits the Qtool estimation accuracy. Although higher TP performance variations can be covered with an additional margin, this approach would reduce the efficiency and consume the benefits of disaggregation. Therefore, we propose PLM extensions that capture the performance variations of multi- vendor TPs. In particular, we propose four TP vendor dependent performance factors and we also devise a Machine Learning (ML) scheme to learn these performance factors in offline and online network planning scenarios. The proposed extended PLM and ML training scheme are evaluated through realistic simulations. Results show a design margin reduction of greater than 1 dB for new connection requests in a disaggregated network with TPs from four vendors. On top of this, the results also show a ~0.5 dB additional Signal to Noise Ratio (SNR) saving for new connection requests by proper selection of the TPs., This work is a part of the Future Optical Networks for Innovation, Research and Experimentation (ONFIRE) Project (Project ID-765275)., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Adaptive and iterative QoT estimator retraining for launch power optimization

  • Mahajan, Ankush
  • Christodoulopoulos, Konstantinos
  • Martínez Rivera, Ricardo Victor
  • Muñoz González, Raül
  • Spadaro, Salvatore
We dynamically optimize the transponders launch powers with iterative closed control loops. We close the loop after an adaptable number of algorithm’s intermediate calculations, to monitor and retrain the QoT estimator with the real world., This work is a part of H2020-MSCA, ONFIRE project supported by EU, grant agreement No. 765275., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Machine learning-based in-band OSNR estimation from optical spectra

  • Locatelli, Fabiano
  • Christodoulopoulos, Konstantinos
  • Svaluto Moreolo, Michela
  • Fàbrega, Josep Maria
  • Spadaro, Salvatore
© 2019 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., Measuring the optical signal to noise ratio (OSNR) at certain network points is essential for failure handling, for single connection but also global network optimization. Estimating OSNR is inherently difficult in dense wavelength routed networks, where connections accumulate noise over different paths and tight filters do not allow the observation of the noise level at signal sides. We propose an in-band OSNR estimation process, which relies on a machine learning (ML) method, in particular on Gaussian process (GP) or support vector machine (SVM) regression. We acquired high-resolution optical spectra, through an experimental setup, using a Brillouin optical spectrum analyzer (BOSA), on which we applied our method and obtained excellent estimation accuracy. We also verified the accuracy of this approach for various resolution scenarios. To further validate it, we generated spectral data for different configurations and resolutions through simulations. This second validation confirmed the estimation quality of the proposed approach., The authors would like to thank Aragon Photonics Labs for providing the BOSA used for the experiments. This work was partially funded by the ONFIRE project supported by EU Horizon 2020 research and innovation programme under the Marie Skłodowska-Curie grant agreement No. 765275, Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Modelling multi-vendor transponders performance and optimizing launch power

  • Mahajan, Ankush
  • Christodoulopoulos, Konstantinos
  • Martínez Rivera, Ricardo Victor
  • Spadaro, Salvatore
  • Muñoz González, Raül
We propose physical layer model extensions that capture the performance variations of multivendor transponders and use those with appropriate algorithms to optimize connections’ launch powers. We estimated potential SNR improvements upto ~35% for 4 different vendors in a network of 27 nodes., This work is a part of ONFIRE project supported by EU Horizon 2020 research and innovation programme under the MSCA grant agreement No. 765275., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Filter features extraction from optical spectra

  • Locatelli, Fabiano
  • Christodoulopoulos, Konstantinos
  • Fàbrega Sánchez, Josep Maria
  • Svaluto Moreolo, Michela
  • Nadal Reixats, Laia
  • Spadaro, Salvatore
We propose a method to estimate the central frequency and the bandwidth of optical filters, that relies on optical spectra captured with optical channel monitors at ROADM’s ingress port. We demonstrate for both features high estimation accuracy using simulated and experimental data., This work was funded by the ONFIRE project supported by the EU Horizon 2020 research and innovation programme under the Marie Skłodowska-Curie grant agreement No. 765275., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Spectral processing techniques for efficient monitoring in optical networks

  • Locatelli, Fabiano
  • Christodoulopoulos, Konstantinos
  • Svaluto Moreolo, Michela
  • Fàbrega Sánchez, Josep Maria
  • Nadal Reixats, Laia
  • Spadaro, Salvatore
Having ubiquitous optical monitors in dense wavelength-division multiplexing (DWDM) or flex-grid networks allows the estimation in real time of crucial parameters. Such monitoring would be even more important in disaggregated optical networks, to inspect performance issues related to inter-vendor interoperability. Several important parameters can be retrieved using optical spectrum analyzers (OSAs). However, omnipresent OSAs represent an infeasible solution. Nevertheless, the advent of new, relatively cheap, compact and medium-resolution optical channel monitors (OCMs) enable a more intensive deployment of these devices. In this paper, we identify two main scenarios for the placement of such monitors: at the ingress and at the egress of the optical nodes. In the ingress scenario, we can directly estimate the parameters related to the signals, but not those related to the filters. On the contrary, in the egress scenario, the filter-related parameters can be easily detected, but not those related to amplified spontaneous emission. Therefore, we present two methods that, leveraging a curve fitting and a machine learning regression algorithm, allow detection of the missing parameters. We verify the proposed solutions with spectral data acquired in simulation and experimental setups. We obtained good estimation accuracy for both setups and for both studied placement scenarios. It is noteworthy that in the experimental assessment of the ingress scenario, we achieved a maximum absolute error (MAE) lower than 1 GHz in filter bandwidth estimation and a MAE lower than 0.5 GHz in filter frequency shift estimation. In addition, by comparing the relative errors of the considered parameters, we identified the ingress scenario as the more beneficial. In particular, we estimated the filter central frequency shift with 84% and the filter 6 dB bandwidth with 75% higher accuracy, with respect to datasheet/reference values. This translates into a total reduction of the estimated signal-to-noise ratio (SNR) penalty, introduced by a single optical filter, of 0.24 dB., Funding: Horizon 2020 Framework Programme (765275). This work is part of the Future Optical Networks for Innovation, Research and Experimentation (ONFIRE) project (https://h2020-onfire.eu), which is supported by the European Union’s Horizon 2020 Research and Innovation Programme under the Marie Skłodowska-Curie Action., Peer Reviewed, Postprint (author's final draft)