Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Nanocrystalline electrodeposited Fe-W/Al2O3 Composites, effect of Alumina Sub-microparticles on the mechanical, tribological, and corrosion properties

  • Nicolenco, Aliona|||0000-0003-4624-2163
  • Mulone, Antonio
  • Imaz, Naroa
  • Tsyntsaru, Natalia|||0000-0002-9813-2460
  • Sort, Jordi|||0000-0003-1213-3639
  • Pellicer, Eva|||0000-0002-8901-0998
  • Klement, Uta
  • Cesiulis, Henrikas|||0000-0002-5077-7884
  • García-Lecina, Eva|||0000-0001-8915-840X
In this study, nanocrystalline Fe-W alloy and Fe-W/Al2O3 composite coatings with various contents of sub-microsized alumina particles have been obtained by electrodeposition from an environmentally friendly Fe(III)-based electrolyte with the aim to produce a novel corrosion and wear resistant material. The increase in volume fraction of Al2O3 in deposits from 2 to 12% leads to the grain refinement effect, so that the structure of the coatings change from nanocrystalline to amorphous-like with grain sizes below 20 nm. Nevertheless, the addition of particles to the Fe-W matrix does not prevent the development of a columnar structure revealed for all the types of studied coatings. The observed reduction in both hardness and elastic modulus of the Fe-W/Al2O3 composites is attributed to the apparent grain size refinement/amorphization and the nanoporosity surrounding the embedded Al2O3 particles. In the presence of 12 vol% of Al2O3 in deposits, the wear rate decreases by a factor of 10 as compared to Fe-W alloy tested under dry friction conditions due to the lowering of tribo-oxidation. The addition of alumina particles slightly increases the corrosion resistance of the coatings; however, the corrosion in neutral chloride solution occurs through the preferential dissolution of Fe from the matrix. The obtained results provide a possibility to integrate the nanocrystalline Fe-W/Al2O3 composite coatings into various systems working under dry friction conditions, for example, in high-temperature vacuum systems.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Mechanical, magnetic and magnetostrictive properties of porous Fe-Ga films prepared by electrodeposition

  • Nicolenco, Aliona|||0000-0003-4624-2163
  • Chen, Yu|||0000-0001-9890-9551
  • Tsyntsaru, Natalia|||0000-0002-9813-2460
  • Cesiulis, Henrikas|||0000-0002-5077-7884
  • Pellicer, Eva|||0000-0002-8901-0998
  • Sort, Jordi|||0000-0003-1213-3639
Magnetostriction, known as the ability of magnetic materials to expand or contract in response to magnetic field, is a key property of Fe-Ga alloys exploited in various types of transducers. Usually, thin films of Fe-Ga deposited on rigid substrates suffer from a clamping effect that hinders the propagation of strain. Herein, Fe-Ga films with macroporous, not fully constrained, geometry are prepared by electrodeposition on metallized silicon substrates templated with sub-micrometer-sized polystyrene spheres. For comparison, fully-dense and inherently nanoporous films are prepared by sputtering and electrodeposition, respectively. The electrodeposition mechanism is discussed in terms of electrochemically active species distribution and partial current densities. The composition of the Fe-Ga films has been tuned (2-40 at.% Ga) by varying the electrodeposition parameters. A complete assessment of the nanomechanical and magnetic properties of the films with variable composition and porosity has been performed for an optimized performance. The magnetostriction has been studied by X-ray diffraction applying an in-situ magnetic field. The results demonstrate a larger magnetic-field-induced crystal deformation in templated (macroporous) films compared to the non-templated and fully-dense counterparts. The observed effects in porous Fe-Ga films are very appealing for the design of various strain-engineered nanomaterials, e.g., energy transducers or magnetoelectric composites.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Electrodeposited Fe on Cu foam as advanced fenton reagent for catalytic mineralization of methyl orange

  • Vainoris, Modestas
  • Nicolenco, Aliona|||0000-0003-4624-2163
  • Tsyntsaru, Natalia|||0000-0002-9813-2460
  • Podlaha-Murphy, Elisabeth
  • Alcaide, Francisco|||0000-0002-3373-3978
  • Cesiulis, Henrikas|||0000-0002-5077-7884
In many countries, the textile industry remains the major contributor to environmental pollution. Untreated textile dyes discharged into water negatively impact the performance of aquatic organisms and may cause a variety of serious problems to their predators. Effective wastewater treatment is a key to reducing environmental and human health risks. In this work, the Fe/Cu catalysts were used in heterogeneous Fenton's reaction for the degradation of high concentrations of methyl orange (model azo dye) in aqueous solutions. For the first time, the catalysts were prepared onto commercial copper foams by potentiostatic electrodeposition of iron using an environmentally friendly electrolyte. The influence of electrodeposition conditions, HO concentration, dye concentration and temperature on the model dye degradation was investigated. It was revealed that both the surface area and the catalyst loading play the major role in the effective dye degradation. The experimental results involving spectrophotometric measurements coupled with total carbon and nitrogen quantification suggest that a solution containing up to 100 mg/L of methyl orange can be successfully decolorized within 90 s at 50°C using porous Fe/Cu catalyst in the presence of hydrogen peroxide that largely surpasses the current state-of-the-art performance. Already within the first 10°min, ∼ 30% of total methyl orange concentration is fully mineralized. The described process represents a cost-efficient and environmentally friendly way to treat azo dyes in aqueous solutions.