Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 11
Encontrada(s) 1 página(s)

e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publication Artículo científico (JournalArticle)

Optical characterization of lead-free Cs2SnI6 double Perovskite Fabricated from degraded and reconstructed CsSnI3 films

  • López Fraguas, Eduardo
  • Dasi, Sofía
  • Mora Sero, Iván
Halide perovskites have experienced a huge development in the past years, but they still have two major challenges for their massive implantation: the long-term stability and the use of lead. One of the most obvious lead-free candidates to replace these perovskites is CsSnI3, but due to its poor environmental stability, it has been discarded for the fabrication of stable devices. Nevertheless, ambient degradation of CsSnI3 and ulterior reconstruction produce a relatively stable lead-free Cs2SnI6 double perovskite with interesting optical properties that have not been deeply characterized previously. In this work, the potential use for the optical properties of Cs2SnI6 is studied and compared with that of the most common halide perovskite, CH3NH3PbI3 (MAPbI3). The Cs2SnI6 films stayed in a standard atmosphere for a week without showing any signs of degradation. They also demonstrated better reflective behavior than MAPbI3 and higher absorption in the 650 and 730 nm spectral range, making this material interesting for the development of photodetectors in this region. This study demonstrates that Cs2SnI6 is a promising material for photodevices, as it highlights its main characteristics and optical parameters, giving an original view on the use of the double perovskite, but at the same time emphasizing the need to improve the electrical properties for the development of efficient optoelectronic devices., E.L.-F. wants to express his gratitude to the Ministerio de Educación y Formación Profesional for his doctoral grant (FPU research fellowship FPU17/00612) and his research stay grant (EST18/00399). This work was partially supported by the European Research Council (ERC) via Consolidator Grant (724424-No-LIMIT) and the European Commission via FET Open Grant (862656 - DROP-IT). We acknowledge SCIC from Jaume I University (UJI) for help with XRD and SEM-EDS characterization.
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publication Tesis doctoral (DoctoralThesis)

Contribution to characterization of last-generation photodetectors and improvement of their efficiency using micro and nanostructures

  • López Fraguas, Eduardo
Mención Internacional en el título de doctor, The world is going through constant technological changes, and what it seems to be a great improvement to the life in Earth at one moment, can lead to disastrous effects in the future. This has happened several times during the human being history, and one clear example is the climate change, global warming, and greenhouse effect. Since the industrial revolution, the humanity went through several technological changes: some of them allowed us to progress as a civilization, but others will lead us to self-destruction. A recent example is the release of chlorofluorocarbon (CFC) gases that destroyed a huge part of the ozone layer at the Earth’s poles. Nowadays, one of the big problems that we are facing is the massive amount of carbon dioxide that we are throwing into atmosphere, mainly due to the energy generation activities. That is why this thesis is focused on increase the efficiency of devices that produce energy in a cleaner way, using solar energy. Doing so, in a near future we will be able to replace the actual contaminating energy sources for cleaner, non-emitting, renewable energy sources. Of course, this topic is too general, so this work is split in three big sections, intending to give full coverage to the topic. The first section is based onto the building blocks of solar harvesting, i.e., the solar cells. The more mature technology, commercially available is the silicon-based solar cell, but in the last years, a lot of technologies were also developed such as organic photovoltaics or perovskites. Each of these technologies have their own fabrication procedure, being the silicon very expensive and high energy demanding, while in the case of organic or perovskite the fabrication procedures are usually solvent-based and cheaper in terms of energy and material costs. After a brief explanation of the most used thin-film deposition techniques (used on organics and perovskites) the building process of a methylammonium lead iodide perovskite is explained step by step. This fabrication gave a resulting solar cell with a power conversion efficiency of 16.9%. Due to the environmental issues that this novel material can cause (mainly because it has lead in its composition), a lead-free perovskite was also studied (cesium tin iodide). The conclusion extracted from this study is that this lead-free perovskite could have very interesting applications, for example in smart windows, but their electrical conductivity problems should be solved first. Ending with this section, a proof of concept including organic and perovskite photodetectors into a visible light communication system was carried out, resulting in both technologies being able to perform good enough to be part of an audio link (with a bandwith higher than 40 kHz). Once we have a device to work with, in order to stablish their properties, it should be characterized. That is what the second section is about. This characterization must be done in a standardized way, under certain conditions and circumstances. One of these conditions is to have a stable, well-defined illumination source, that can recreate the standard AM1.5G spectrum (which is the spectrum of light that arrives at the Earth’s surface, coming from the Sun). All this restrictions and parameters that dictates whether a light source is valid for this process or not are defined by the International Electrotechnical Commission under the standard IEC 60904-9. During this thesis, due to the necessity of this light to characterize devices, we decided to create one. This gave birth to SUNBOX, our proprietary solar simulator. SUNBOX belongs to a AAA-Class according to the IEC standard, which represents the highest quality possible in solar simulators. It is fully based on light emitting diodes and also customizable, with a tunable spectrum that can go from 0.2 to 1.2 suns and has 14 different wavelengths that can be intensity-tuned freely. It is also clearly distinguishable from the commercial ones because its structure is 3D-printed, so it is lightweight and has a low cost. Due to the intellectual property protection as a utility model, only a brief part regarding the electronic design is explained in this document, together with the calibration procedure that was carried out in terms of spectral match, homogeneity, and temporal instability that qualifies SUNBOX as an AAA-Class solar simulator. At the end of this section, some characterizations made with SUNBOX are shown, using different functionalities, to obtain key parameters in different types of solar cells. The characterization methods that were used, such as I-V curves or spectroscopy impedance are also explained along the document. Finally, in the third section, other approaches to improve the efficiency of the devices were studied, based on the optical treatment of light (light management). This management lies on the ability that some materials have to interact with the incident light, mainly in the form of nanoparticles, nanorods, or small gratings. Using a Finite Element Method simulation software (COMSOL® and JCMSuite®), several results were obtained remarking the importance of the inclusion of a nanostructure inside a device, increasing the amount of photogenerated current by 40% in a hydrogenated amorphous silicon-based device and by 20.5% in a perovskite/silicon tandem solar cell. Furthermore, preliminary results were obtained applying a nanostructure into a deep ultraviolet light emitting diode, that went from a light extraction efficiency value of 4.57% to around 15%, thus, multiplying by three the amount of extracted light with the same electrical power consumption. In summary, the main conclusion of this work is that it is possible to increase the efficiency of actual devices by and important factor and that there is a lot of room for future improvements. A boost in efficiency can be applied not only using novel materials with better electrical and optical properties, but also optimizing the devices that exist nowadays using light management techniques through the inclusion of nanostructures inside these devices. This has been demonstrated during this work using both approaches: the material science, creating a novel material with a cutting-edge fabrication method, unraveling the properties and applications for this material; and the photonics science, simulating the response of the device with the inclusion of a nanostructure in it, showing an outstanding improvement in all three study cases., El mundo actual está constantemente sometido a cambios tecnológicos, y lo que en un momento pudo ser un gran avance para la vida en la Tierra, puede ocasionar efectos desastrosos en el futuro. Esto ha ocurrido en varias ocasiones en la historia de la humanidad y claros ejemplos de ello son el cambio climático, el calentamiento global y el incremento del efecto invernadero. Desde la Revolución Industrial se han producido diversos cambios y avances tecnológicos muy importantes para la sociedad: algunos de ellos nos permitieron avanzar como civilización, pero otros nos dirigen hacia nuestra propia autodestrucción. Un ejemplo reciente podría ser la emisión de los llamados clorofluorocarbonos a la atmósfera, unos gases que destruyeron la mayor parte de la capa de ozono en los polos de la Tierra, ocasionando que una gran parte de radiación solar incidiera en los glaciares polares, incrementando la fusión de ellos y con ello contribuyendo al peligroso deshielo polar. Hoy en día, uno de los grandes problemas a los que nos enfrentamos es la gran cantidad de dióxido de carbono que estamos vertiendo a la atmósfera, principalmente debido a las actividades de generación de energía. Por ello, el objetivo de esta tesis está centrado en incrementar la eficiencia de los dispositivos capaces de producir energía de una forma más limpia, usando la energía solar. De esta forma, en el futuro cercano seremos capaces de sustituir las fuentes de energía contaminantes que usamos actualmente por otras fuentes de energía mas limpia, renovables y que no emitan gases. Cierto es que este tema puede parecer prácticamente inabarcable, y por ello se ha dividido este trabajo en tres secciones principales que se estudian en detalle, para dar cobertura completa a todo el tema. La primera sección está basada en el estudio de las unidades básicas de la recolección de energía solar, las celdas solares. La tecnología más madura comercialmente disponible es la celda solar basada en silicio (tanto monocristalino como policristalino), pero durante los últimos años se han desarrollado otras tecnologías tales como las celdas orgánicas o de perovskita. Cada una de estas tecnologías tiene su propio procedimiento de fabricación, siendo las basadas en silicio las más caras de hacer debido a su procesamiento y a la gran cantidad de energía necesaria para su refinado. Sin embargo, en el caso de las celdas orgánicas y de perovskita los métodos de fabricación están basados en solventes y deposiciones de líquido en capas delgadas, lo que las hace mucho más económicas en términos de materiales y de consumo energético. Después de una breve explicación de las técnicas de deposición de lámina delgada más usadas (aplicables tanto en orgánicas como en perovskitas), se explica el proceso de fabricación paso a paso de una celda solar de yoduro de metilamonio plomo. Esta fabricación dio como resultado una celda solar con un valor de eficiencia del 16.9%. Debido a los problemas ambientales que puede causar este material (ya que contiene plomo, altamente tóxico), durante este trabajo se estudió también una perovskita libre de plomo (yoduro de estaño cesio). La conclusión principal extraída de este estudio es que esta perovskita libre de plomo puede tener aplicaciones muy interesantes, tales como ventanas inteligentes debido a su transparencia, pero sus problemas de conductividad eléctrica deben de ser resueltos en primer lugar, para conseguir un dispositivo eficiente. Para finalizar esta sección, se llevó a cabo una prueba de concepto que consistió en introducir fotodetectores orgánicos y de perovskita en un sistema de comunicación por luz visible (VLC), comprobando que ambas tecnologías respondían de forma correcta para formar parte de un sistema de transmisión de audio (su ancho de banda era superior a 40 kHz en ambos casos). Una vez se dispone de un dispositivo funcional, para poder determinar sus propiedades internas, se debe caracterizar. En esto consiste la segunda sección. Estas caracterizaciones deben hacerse siguiendo los estándares correspondientes, bajo ciertas condiciones y en unas circunstancias determinadas. Una de estas condiciones es tener una fuente de luz estable y bien definida, que pueda recrear el espectro AM1.5G (que es el espectro de luz que llega a la superficie de la Tierra emitido por el Sol) para excitar las muestras que se encuentren bajo análisis. Todas las restricciones y parámetros que determinan si una fuente de luz es adecuada o no para este proceso están definidos por la Comisión Electrotécnica Internacional bajo el estándar IEC 60904-9. Durante el desarrollo de esta tesis, debido a la necesidad de caracterizar dispositivos, se optó por crear una de estas fuentes de luz. Así nació SUNBOX, nuestro simulador solar. SUNBOX pertenece a la clase AAA según el estándar IEC, lo que significa que posee la mayor calidad posible como simulador solar. Está completamente basado en diodos emisores de luz y también es personalizable, con un espectro ajustable que puede cubrir desde 0.2 hasta 1.2 soles. Dispone de 14 longitudes de onda de emisión diferentes que también pueden ser ajustadas libremente, de forma que se pueden realizar análisis en longitudes de onda concretas, tales como azul, ultravioleta o infrarrojo. Es fácilmente distinguible de sus contrapartes comerciales disponibles en el mercado, ya que su chasis está realizado por impresión 3D, así que es muy ligero y de bajo coste. Debido a la protección de la propiedad intelectual bajo un modelo de utilidad y un registro software, solo una parte del diseño electrónico se explica en este documento, junto con todo el procedimiento de calibración que se llevó a cabo en términos de coincidencia espectral, homogeneidad y estabilidad temporal, que clasifican a SUNBOX como un simulador solar de clase AAA. Al final de esta sección, se muestran algunas de las caracterizaciones de dispositivos llevadas a cabo con SUNBOX, usando sus diferentes funcionalidades para obtener parámetros clave de distintos tipos de celdas solares. Los métodos de caracterización llevados a cabo, tales como el trazado de curvas tensión corriente o la espectroscopía de impedancias también se explican en el documento. Por último, en la tercera sección, se estudian otras técnicas para mejorar la eficiencia de los dispositivos, basadas en el tratamiento óptico de la luz (gestión de la luz o “light management”). Esta gestión de la luz se basa en la habilidad que tienen algunos materiales para interactuar con la luz que incide sobre ellos. Normalmente estos materiales necesitan estar en forma de nanopartículas, nanobarras o pequeñas redes de difracción. Usando varios softwares de simulación (COMSOL® y JCMSuite®) basados en el método de elementos finitos (FEM), se han obtenido varios resultados que remarcan la importancia de incluir nanoestructuras dentro de los dispositivos, incrementando la cantidad de corriente fotogenerada en un 40% en un dispositivo basado en silicio amorfo hidrogenado y en un 20.5% en un dispositivo basado en un tándem de perovskita y silicio monocristalino. Además, se han obtenido resultados preliminares que demuestran que estas nanoestructuras pueden ser también muy efectivas no solo en dispositivos receptores de luz, sino también en emisores. En este caso se aplicó una nanoestructura a un diodo emisor de luz ultravioleta profunda, que mejoró su eficiencia de extracción de luz de un 4.57% a alrededor de un 15%, triplicando la cantidad de luz emitida con el mismo consumo de potencia eléctrica. En resumen, la conclusión principal de este trabajo es que es posible incrementar la eficiencia de los dispositivos actuales de una forma sustancial, quedando aún mucho espacio para mejorar. Se ha demostrado que un incremento en la eficiencia puede obtenerse no solo usando materiales novedosos con mejores propiedades ópticas y eléctricas, sino también optimizando los dispositivos existentes actualmente usando técnicas de gestión de la luz a través de la inclusión de nanoestructuras en estos dispositivos. Respecto a la primera aproximación, relacionada con la ciencia de materiales, en este trabajo se ha fabricado un material novedoso usando una técnica de fabricación poco explorada en estas aplicaciones (co-evaporación), descubriendo las propiedades y posibles aplicaciones de este material. Respecto a la segunda aproximación, relacionada con la fotónica, se han creado diseños de nanoestructuras y se ha simulado su respuesta, descubriendo una mejora muy importante en la eficiencia de los tres dispositivos estudiados., The present work has been funded from the following projects: • Comunidad de Madrid through SINFOTON-CM Research Program (S2013/MIT-2790) and SINFOTON2-CM (S2018/NMT-4326) • Ministerio de Economia, Agencia Estatal de Investigación and European Union’s FEDER through TEC2016-77242-C3-(1-R, 2-R and 3-R) AEI/FEDER, UE Projects. • European Research Council (ERC) via Consolidator Grant (724424-No-LIMIT) • Generalitat Valenciana via Prometeo Grant Q-Devices (Prometeo/2018/098) • European Commission via FET Open grant (862656-DROP-IT) Also, this project could not be possible with the financial support of the Ministerio de Educación y Formación Profesional through the following grants that I have received: • Doctoral Grant FPU research fellowship (FPU17/00612). • Research Stay Grant (EST18/00399) supporting my research stay at Jaume I University (Castellón, Spain) • Research Stay Grant (EST19/00073) supporting my research stay at Helmholtz Zentrum Berlin and Zuse Institute Berlin (Berlin, Germany)., Programa de Doctorado en Ingeniería Eléctrica, Electrónica y Automática por la Universidad Carlos III de Madrid, Presidente: Javier Alda Serrano.- Secretario: Fernando B. Naranjo Vega.- Vocal: Sven Burger
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Chemically driven dimensionality modulation of hybrid tin(ii) halide perovskite microcrystals

  • Sánchez-Alarcón, Raul I.
  • Solis, Omar E.
  • Momblona-Rincon, Maria Cristina
  • Ripolles, Teresa S.
  • Martínez-Pastor, Juan P.
  • Abargues, Rafael
  • Boix, Pablo P.|||0000-0001-9518-7549
[EN] The lattice arrangement of lead-free perovskites can be altered by synthesis parameters such as concentration, temperature, choice of solvents, and the length of monovalent cations. This effect, often described as dimensionality modulation, can be exploited to develop new materials with better optical properties than their three-dimensional counterpart. This work explores the versatility of the hot-injection synthesis for obtaining 2-thiopheneethylammonium (TEA(+)) based tin halide perovskite microcrystals. The dimensionality of TEA-based tin bromide perovskite microcrystals can be modulated through changes in the TEA concentration, giving rise to the formation of highly luminescent 0D-TEA(4)SnBr(6) and low-emissive 2D-TEA(2)SnBr(4) microplates. In contrast, 0D-[TEASnCl(3)][TEACl] and 2D-TEA(2)SnI(4) are thermodynamically preferred as main products when using the chloride and iodide analogues, respectively, limiting the dimensional versatility. It is noteworthy that 0D-TEA(4)SnBr(6) shows the highest PLQY from the low dimensional TEA tin halide family (PLQY = 75% in thin-film) owing to a more confined configuration based on isolated [SnBr6](4-) octahedra moieties separated by TEA(+) cations, being attractive for optoelectronic applications., This project has received funding from the European Union's Horizon 2020 research and innovation program under grant agreement No. 862656 (project DROP-IT) by the Spanish MICINN through project no. PID2020-120484RB. We acknowledge the support from the Spanish MINECO through the project Nirvana (no. PID2020-119628RB-C31) by MCIN/AEI/10.13039/501100011033. Also, we acknowledge the financial support from Generalitat Valenciana through the CIDEGENT contract (ref: CIDEGENT/2021/044) and CIAPOS 2022/018 grant. The work was partially funded by MCIN/AEI through project TED2021-131600B-C32.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Ecofriendly Perovskites with Giant Self-Defocusing Optical Response

  • Suárez, Isaac
  • Martinez-Pastor, Juan P.
  • Oszajca, Marek F.
  • Lüchinger, Norman A.
  • Graves, Brian
  • Agouram, Said
  • Ferrando, Albert
  • Milián Enrique, Carles|||0000-0001-8492-366X
[EN] The full optical control of light using sustainable green technologies is one of the incipient challenges of the Photonics community. There are, however, few optical materials able to provide a significant nonlinear refractive index change under small enough intensities (< 1 GW cm(-2)), and, more importantly, allowing the external control of the magnitude and sign of their nonlinear response. This manuscript demonstrates that Cs2SnI6 lead-free nanocrystals (NCs) present an extraordinary self-defocusing response not yet observed up to now in any material. Despite its complex structural form, these NCs are fully characterized here, both experimentally and theoretically, revealing a giant negative refractive change Delta n = -0.05 under proper illumination conditions. The nonlinear response is tuned with the intensity, concentration of NCs in the solvent, and propagation distance leading to a crossover where the media transforms to self-focusing with Delta n = +0.002. These results can provide fascinating opportunities in sensing and light-matter interactions for a future ecofriendly photonic technology., This project has received funding from the European Union's Horizon 2020 research and innovation programme under grant agreement no. 862656 (project DROP-IT) and by the Spanish MICINN through project no. PID2020-120484RB-I00 and by Generalitat Valenciana PROMETEO/2021/082.
Investigo. Repositorio Institucional de la Universidade de Vigo
Publication Artículo científico (JournalArticle)

Lead‐free halide perovskite materials and optoelectronic devices: progress and prospective

  • López Fernández, Iago
  • Valli, Donato
  • Wang, Chun‐Yun
  • Samanta, Subarna
  • Okamoto, Takuya
  • Huang, Yi‐Teng
  • Sun, Kun
  • Liu , Yang
  • Chirvony, Vladimir S.
  • Patra, Avijit
  • Zito, Juliette
  • De Trizio, Luca
  • Gaur , Deepika
  • Sun, Hong‐Tao
  • Xia, Zhiguo
  • Li, Xiaoming
  • Zeng, Haibo
  • Mora‐Seró, Iván
  • Pradhan, Narayan
  • Martínez‐Pastor, Juan P.
  • Müller‐Buschbaum, Peter
  • Biju, Vasudevanpillai
  • Debnath, Tushar
  • Saliba, Michael
  • Debroye, Elke
  • Hoye, Robert L. Z.
  • Infante, Ivan
  • Manna, Liberato
  • Polavarapu , Lakshminarayana
Halide perovskites, in the form of thin films and colloidal nanocrystals, have recently taken semiconductor optoelectronics research by storm, and have emerged as promising candidates for high‐performance solar cells, light‐emitting diodes (LEDs), lasers, photodetectors, and radiation detectors. The impressive optical and optoelectronic properties, along with the rapid increase in efficiencies of solar cells and LEDs, have greatly attracted researchers across many disciplines. However, most advances made so far in terms of preparation (colloidal nanocrystals and thin films), and the devices with highest efficiencies are based on Pb‐based halide perovskites, which have raised concerns over their commercialization due to the toxicity of Pb. This has triggered the search for lower‐toxicity Pb‐free halide perovskites and has led to significant progress in the last few years. In this roadmap review, researchers of different expertise have joined together to summarize the latest progress, outstanding challenges, and future directions of Pb‐free halide perovskite thin films and nanocrystals, regarding their synthesis, optical spectroscopy, and optoelectronic devices, to guide the researchers currently working in this area as well as those that will join the field in the future., Agencia Estatal de Investigación | Ref. RYC2018-026103-I, Agencia Estatal de Investigación | Ref. PID2020-117371RA-I00, Agencia Estatal de Investigación | Ref. TED2021-131628A-I00, Xunta de Galicia | Ref. ED431F2021/05, Agencia Estatal de Investigación | Ref. TED2021-131600B-C31, Generalitat Valenciana | Ref. MFA/2022/020, Universidade de Vigo/CISUG
RUA. Repositorio Institucional de la Universidad de Alicante
Publication Otros (Other)

Control of Stimulated Emission of Tin Perovskites through Polymeric Diffractive Gratings

  • Martínez-Pastor, Juan P.
  • Sánchez-Díaz, Jesús
  • Villalvilla, José M.
  • Soriano-Díaz, Sandra
  • Quintana, José A.
  • Mora-Sero, Ivan
  • Díaz-García, María A.
  • Suárez, Isaac
  • Díaz-García, María A.|||/items/3b28d03f-511f-4a32-9ff4-d4a2e740834f
  • Villalvilla, José M.|||/items/e57ae241-3d26-4d3e-815b-6f890edaa475
FASnI3 (FA: formamidinium) polycrystalline perovskite thin films have demonstrated to be an excellent gain media and less toxic alternative to the Pb-containing perovskite light emitters. However, the instability of Sn perovskites prevents the postprocessing of the film after deposition, making its integration in two-dimensional optical architectures challenging. In this article, FASnI3 polycrystalline thin films are successfully integrated with polymeric diffractive gratings under cost-effective and industrial compatible technology. The gratings are fabricated under holographic techniques, allowing patterning on large areas (≈1 cm2) and the posterior deposition of the perovskite films or cladding layers. The grating period demonstrated to be an adequate tuning parameter to control the amplified spontaneous emission (ASE) properties. Notably, the overlap of the mode with the emission band represents a suitable mechanism to selectively enhance the generation of the ASE (tuned device) above a moderate threshold of 100 μJ/cm2 and extract the random lasing lines created on the grains of the film (detuned device). These results represent a significant advance on Sn-perovskite-based optical sources, offering cost-effective technology for next-generation photonic applications.
Dipòsit Digital de la UB
Publication Artículo científico (JournalArticle)

High Quality Inkjet Printed‐Emissive Nanocrystalline Perovskite CsPbBr3 Layers for Color Conversion Layer and LEDs Applications

  • Vescio, Giovanni
  • Frieiro Castro, Juan Luis
  • Gualdrón‐Reyes, Andrés F.
  • Hernández Márquez, Sergi
  • Mora‐Seró, Ivan
  • Garrido Fernández, Blas
  • Cirera Hernández, Albert
Metal halide perovskites (MHPs) have shown outstanding optical emissive properties and can be employed in several optoelectronics devices. In contrast with materials of well-established technologies, which are prone to degradation or require expensive processes, MHPs can be obtained by solution processing methods and increase stability. Inkjet printing is proposed as an industrial friendly technique to deposit MHPs. The inks have been developed from colloidal CsPbBr3 nanocrystals and printing procedures that allow the deposition of thin layers with intense green emission. High emissive printed layers are assured by carrying out thermal annealing in vacuum oven, which is demonstrated to promote compact layers with low roughness, corroborated by SEM and AFM. XRD measurements show CsPbBr3 crystalline layers with cubic symmetry and XPS provides insight into the stoichiometric composition and local bonding. Optical properties of inkjet-printed CsPbBr3 films have been analyzed by UV-vis absorbance and photoluminescence (PL), to extract the bandgap energy and photoluminescence quantum yield (PLQY). CsPbBr3 printed layers emit at 524 nm with a narrow emission (FWHM ≈ 15 nm), exhibiting a PLQY up to 20%. These results enabled the large-scale fabrication by inkjet printing of CsPbBr3 color conversion layers (CCLs) and pave the way for flexible LEDs.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Exploiting the Lability of Metal Halide Perovskites for Doping Semiconductor Nanocomposites

  • Calcabrini, Mariano
  • Calcabrini, Mariano
  • Genç, Aziz
  • Genç, Aziz
  • Liu, Yu
  • Liu, Yu
  • Kleinhanns, Tobias
  • Kleinhanns, Tobias
  • Lee, Seung-Ho
  • Dirin, Dmitry N.
  • Akkerman, Quinten A.
  • Kovalenko, Maksym V.
  • Arbiol, Jordi
  • Ibáñez, María
Cesium lead halides have intrinsically unstable crystal lattices and easily transform within perovskite and nonperovskite structures. In this work, we explore the conversion of the perovskite CsPbBr3 into Cs4PbBr6 in the presence of PbS at 450 °C to produce doped nanocrystal-based composites with embedded Cs4PbBr6 nanoprecipitates. We show that PbBr2 is extracted from CsPbBr3 and diffuses into the PbS lattice with a consequent increase in the concentration of free charge carriers. This new doping strategy enables the adjustment of the density of charge carriers between 1019 and 1020 cm-3, and it may serve as a general strategy for doping other nanocrystal-based semiconductors., M.C. has received funding from the European Union’s Horizon 2020 research and innovation programme under the Marie Skłodowska-Curie Grant Agreement No. 665385. ICN2 acknowledges funding from Generalitat de Catalunya 2017 SGR 327. ICN2 is supported by the Severo Ochoa program from Spanish MINECO (Grant No. SEV-2017-0706) and is funded by the CERCA Programme/Generalitat de Catalunya. This project has received funding from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 823717 – ESTEEM3. M.V.K. acknowledges the support by the European Research Council under the Horizon 2020 Framework Program (ERC Consolidator Grant SCALE-HALO Grant Agreement No. 819740) and by FET-OPEN project no. 862656 (DROP-IT).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Chemically driven dimensionality modulation of hybrid tin(ii) halide perovskite microcrystals

  • Sánchez-Alarcón, Raúl I.
  • Solis, Omar E.
  • Momblona-Rincon, María Cristina
  • Ripolles,Teresa S.
  • Martínez-Pastor, Juan P.
  • Abargues, Rafael
  • Boix, Pablo P.
The lattice arrangement of lead-free perovskites can be altered by synthesis parameters such as concentration, temperature, choice of solvents, and the length of monovalent cations. This effect, often described as dimensionality modulation, can be exploited to develop new materials with better optical properties than their three-dimensional counterpart. This work explores the versatility of the hot-injection synthesis for obtaining 2-thiopheneethylammonium (TEA) based tin halide perovskite microcrystals. The dimensionality of TEA-based tin bromide perovskite microcrystals can be modulated through changes in the TEA concentration, giving rise to the formation of highly luminescent 0D-TEASnBr and low-emissive 2D-TEASnBr microplates. In contrast, 0D-[TEASnCl][TEACl] and 2D-TEASnI are thermodynamically preferred as main products when using the chloride and iodide analogues, respectively, limiting the dimensional versatility. It is noteworthy that 0D-TEASnBr shows the highest PLQY from the low dimensional TEA tin halide family (PLQY = 75% in thin-film) owing to a more confined configuration based on isolated [SnBr] octahedra moieties separated by TEA cations, being attractive for optoelectronic applications., This project has received funding from the European Union's Horizon 2020 research and innovation program under grant agreement No. 862656 (project DROP-IT) by the Spanish MICINN through project no. PID2020-120484RB. We acknowledge the support from the Spanish MINECO through the project Nirvana (no. PID2020-119628RB-C31) by MCIN/AEI/10.13039/501100011033. Also, we acknowledge the financial support from Generalitat Valenciana through the CIDEGENT contract (ref: CIDEGENT/2021/044) and CIAPOS 2022/018 grant. The work was partially funded by MCIN/AEI through project TED2021-131600B-C32.
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

High Quality Inkjet Printed‐Emissive Nanocrystalline Perovskite CsPbBr3 Layers for Color Conversion Layer and LEDs Applications

  • Vescio, Giovanni
  • Frieiro Castro, Juan Luis
  • Gualdrón‐Reyes, Andrés F.
  • Hernández Márquez, Sergi
  • Mora‐Seró, Ivan
  • Garrido Fernández, Blas
  • Cirera Hernández, Albert
Metal halide perovskites (MHPs) have shown outstanding optical emissive properties and can be employed in several optoelectronics devices. In contrast with materials of well-established technologies, which are prone to degradation or require expensive processes, MHPs can be obtained by solution processing methods and increase stability. Inkjet printing is proposed as an industrial friendly technique to deposit MHPs. The inks have been developed from colloidal CsPbBr3 nanocrystals and printing procedures that allow the deposition of thin layers with intense green emission. High emissive printed layers are assured by carrying out thermal annealing in vacuum oven, which is demonstrated to promote compact layers with low roughness, corroborated by SEM and AFM. XRD measurements show CsPbBr3 crystalline layers with cubic symmetry and XPS provides insight into the stoichiometric composition and local bonding. Optical properties of inkjet-printed CsPbBr3 films have been analyzed by UV-vis absorbance and photoluminescence (PL), to extract the bandgap energy and photoluminescence quantum yield (PLQY). CsPbBr3 printed layers emit at 524 nm with a narrow emission (FWHM ≈ 15 nm), exhibiting a PLQY up to 20%. These results enabled the large-scale fabrication by inkjet printing of CsPbBr3 color conversion layers (CCLs) and pave the way for flexible LEDs.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Exploiting the lability of metal halide perovskites for doping semiconductor nanocomposites

  • Calcabrini, Mariano|||0000-0003-4566-5877
  • Genç, Aziz|||0000-0002-2888-2549
  • Liu, Yu|||0000-0001-7313-6740
  • Kleinhanns, Tobias
  • Lee, Seungho|||0000-0002-6962-8598
  • Dirin, Dmitry N.|||0000-0002-5187-4555
  • Akkerman, Quinten A.
  • Kovalenko, Maksym V.|||0000-0002-6396-8938
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Ibáñez, Maria|||0000-0001-5013-2843
Cesium lead halides have intrinsically unstable crystal lattices and easily transform within perovskite and nonperovskite structures. In this work, we explore the conversion of the perovskite CsPbBr into CsPbBr in the presence of PbS at 450 °C to produce doped nanocrystal-based composites with embedded CsPbBr nanoprecipitates. We show that PbBr is extracted from CsPbBr and diffuses into the PbS lattice with a consequent increase in the concentration of free charge carriers. This new doping strategy enables the adjustment of the density of charge carriers between 10 19 and 10 20 cm -3, and it may serve as a general strategy for doping other nanocrystal-based semiconductors.