Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Polycaprolactone/gelatin-based scaffolds with tailored performance: in vitro and in vivo validation

  • Gil-Castell, O.
  • Badia, J.D.
  • Ontoria-Oviedo, I.
  • Castellano, D.
  • Sepúlveda, P.
  • Ribes-Greus, A.|||0000-0003-2460-8291
[EN] Nanofibrous scaffolds composed of polycaprolactone (PCL) and gelatin (Ge) were obtained through a hydrolytic assisted electrospinning process. The PCL-to-Ge proportion (100/0 to 20/80), as well as the dissolution time (24, 48, 72, 96, 120 h) into a 1:1 formic/acetic acid solvent before electrospinning were modified to obtain the different samples. A strong influence of these factors on the physicochemical properties of the scaffolds was observed. Higher Ge percentage reduced crystallinity, allowed a uniform morphology and increased water contact angle. The increase in the dissolution time considerably reduced the molar mass and, subsequently, fibre diameter and crystallinity were affected. During in vitro biocompatibility tests, higher cell adhesion and proliferation were found for the 60/40, 50/50 and 40/60 PCL/Ge compositions that was corroborated by MTT assay, fluorescence and microscopy. A weakened structure, more labile to the in vitro degradation in physiologic conditions was found for these compositions with higher dissolution times (72 and 96 h). Particularly, the 40/60 PCL/Ge scaffolds revealed an interesting progressive degradation behaviour as a function of the dissolution time. Moreover, these scaffolds were non-inflammatory, as revealed by the pyrogen test and after the 15-day subcutaneous in vivo implantation in mice. Finally, a reduction of the scar tissue area after infarction was found for the 40/60 PCL/Ge scaffolds electrospun after 72 h implanted in rat hearts. These results are especially interesting and represent a feasible way to avoid undesired inflammatory reactions during the scaffold assimilation., The Spanish Ministry of Economy and Competitiveness is acknowledged for the project RESOLTEX project (RTC-2015-4185-1). The Spanish Ministry of Education, Culture and Sports is thanked for the pre-doctoral FPU grant of O. Gil-Castell (FPU13/01916). The Generalitat Valenciana is thanked for the APOSTD/2014/041 for J.D. Badia. The Universitat Politècnica de València and IIS LaFe are acknowledged for the SCARDIO project (2014_0460_CRC_COLAB_UPVLAFE_SEPULVEDA). P. Sepúlveda acknowledges the Instituto de Salud Carlos III (ISCIII) for the I3SNS Program. This work was supported by grants PI16/0107 and RETICS Program (RD16/0011/0004) from ISCIII cofunded by the European Regional Development Fund-ERDF Una manera de hacer Europa . The City Council of Algemesí is acknowledged for the XIV Premi Cientificotècnic Ciutat d Algemesí award to O. Gil-Castell, for this work as the best young researcher of the Ribera District.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Crosslinked chitosan/poly(vinyl alcohol)-based polyelectrolytes for proton exchange membranes

  • Gil-Castell, O.
  • Arenga, Francesca
  • Salaberria, A. M.
  • Baschetti, M.G.
  • Labidi, J.
  • Badia, J.D.
  • Teruel-Juanes, Roberto|||0000-0002-0190-4445
  • Ribes-Greus, A.|||0000-0003-2460-8291
[EN] The preparation polyelectrolytes based on crosslinked poly(vinyl alcohol) (PVA) and chitosan (CS) was considered as a feasible alternative to develop highly functionalised, cost-effective and eco-friendly membranes for proton exchange fuel cell technologies. CS/PVA-based membranes were combined with sulfosuccinic acid (SSA) as crosslinking and sulfonating agent, and glycerol (GL) to promote flexibility and favour their manageability. The chemical structure, the thermo-oxidative behaviour, the ethanol uptake, the electric, the proton conductivity, and the performance in direct ethanol fuel cell (DEFC) were assessed. In general, all the CS/PVA-based polyelectrolytes showed a synergetic increase of thermo-oxidative stability, appropriate absorption and diffusion of ethanol and good proton conductivity, suitable for the typical service conditions of fuel cells. The GL in the membranes reacted with SSA, reduced the ethanol absorption, diffusion coefficient and proton conductivity, but acted as a plasticiser that increased the ductile manageability of the polyelectrolytes to be mounted on the membrane-electrode assembly (MEA). Higher presence of CS and higher the proportion of GL in the polyelectrolyte, improved the material performance in the DEFC. In particular, the crosslinked polyelectrolyte 40CS/PVA/SSA/20GLwith a 40 %wt. of CS referred to PVA, and a 20 %wt. of GL referred to CS, showed a suitable behaviour in the DEFC test, with a maximum value of power density of 746 mW·cm-2., The Spanish Ministry of Economy, Industry and Competitiveness is acknowledged for the projects ENE2017-86711-C3-1-R and UPOV13-3E-1947. The Spanish Ministry of Education, Culture and Sports is thanked for the pre-doctoral FPU grant for O. Gil-Castell (FPU13/01916)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Performance of Polyester-Based Electrospun Scaffolds under In Vitro Hydrolytic Conditions: From Short-Term to Long-Term Applications

  • Gil-Castell, O.
  • Badia, José David
  • Bou, Jordi
  • Ribes-Greus, A.|||0000-0003-2460-8291
[EN] The evaluation of the performance of polyesters under in vitro physiologic conditions is essential to design sca olds with an adequate lifespan for a given application. In this line, the degradation-durability patterns of poly(lactide-co-glycolide) (PLGA), polydioxanone (PDO), polycaprolactone (PCL) and polyhydroxybutyrate (PHB) sca olds were monitored and compared giving, as a result, a basis for the specific design of sca olds from short-term to long-term applications. For this purpose, they were immersed in ultra-pure water and phosphate bu er solution (PBS) at 37 C. The sca olds for short-time applications were PLGA and PDO, in which the molar mass diminished down to 20% in a 20¿30 days lifespan. While PDO developed crystallinity that prevented the geometry of the fibres, those of PLGA coalesced and collapsed. The sca olds for long-term applications were PCL and PHB, in which the molar mass followed a progressive decrease, reaching values of 10% for PCL and almost 50% for PHB after 650 days of immersion. This resistant pattern was mainly ascribed to the stability of the crystalline domains of the fibres, in which the diameters remained almost una ected. From the perspective of an adequate balance between the durability and degradation, this study may serve technologists as a reference point to design polyester-based sca olds for biomedical applications., This research was funded by MINISTERIO DE ECONOMIA, INDUSTRIA Y COMPETITIVIDAD, grant number ENE2017-86711-C3-1-R and by the MINISTERIO DE EDUCACION, CULTURA Y DEPORTE, grant number FPU13/01916.