Skip to main content

SIMULACION DE FLUJOS CON INTERFASES DE FLUIDOS Y MATERIALES FRICCIONALES EN HIDRAULICA

BIA2008-00522

•
Funding agency name Ministerio de Ciencia e Innovación
Funding agency acronym MICINN
Program Programa Nacional de Proyectos de Investigación Fundamental
Subprogram Subprograma de Proyectos de Investigación Fundamental no Orientada
Call Proyectos I+D
Call year 2008
State Plan 2008-2011 Plan Nacional de Investigación Científica, Desarrollo e Innovación Tecnológica
Management unit Subdirección General de Proyectos de Investigación
Beneficiary centre UNIVERSIDAD DE GRANADA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 7
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

An enhanced energy conserving time stepping algorithm for frictionless particle contacts

  • Bravo Pareja, Rafael
  • Pérez-Aparicio, José L.
  • Laursen, T.A.
An Enhanced Energy Conserving Algorithm (EECA) formulation for time integration of frictionless contact-impact problems is presented. In it the energy, linear and angular momentum are conserved for every contact using an enhanced Penalty method. Previous formulations for these problems have shown that the total bodies' energy decreases for contact due to an artificial energy transfer between the penalty spring and the contacting bodies. Consequently, they are not able to reproduce a physical response after a single contact, introducing errors in trajectories and velocities. Through the conserving balance equations, EECA computes a physical response by inserting for every contact an additional amount of linear momentum and contact force. The structure of these equations defines the additional linear momentum to restore the energy and the enhanced Penalty method based on a spring and a dashpot. This method approximately enforces the first and second Kuhn-Tucker conditions. The new algorithm has been applied to several frictionless rigid problems using the Discrete Element Method. The first two problems consist of the simulation and analytical comparison of the Newton's Cradle and Carom problems (billiard pool problem). The last two are the hopper filling process and the breaking of a pool ball's triangular arrangement, both of which involve a medium number of contacts. Application of this formulation will be straightforward to elastic and general-shaped bodies using the Finite Element Method., R. Bravo and J.L. Perez-Aparicio were partially supported by the MFOM I+D (2004/38), MICIIN #BIA-2008-00522 and 'Ayudas Investigacion' from UPV2010 grants.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Refined Element Discontinuous Numerical Analysis of Dry-Contact Masonry Arches

  • Pérez-Aparicio, José L.
  • Bravo, R.
  • Ortiz Rossini, Pablo
The behavior of buried masonry arches is studied in this article using the Discontinuous Deformation Analysis (DDA), a numerical method that allows for the physical simulation of the intrinsic structure dis- continuities since it is based on contact and friction among pseudo-rigid blocks. Two types of arches (or vaults) are studied with a specially developed computer program, one of semicircular and another of ovoidal shape. The loads are self-weight, lateral filling, embankment thrusts and concentrated (through a short distribution) forces close to the peak. These loads are transformed into point forces applied to the center of gravity of each block with simple formulae from classical mechanics. Equilibrium is reached in the whole structure through contact forces calculated with a standard contact algorithm: penalty plus Coulomb friction. DDA-macroblocks composed of linked (through penalty contact springs) pseudo-rigid blocks are for- mulated. This linkage allows for the simulation of collapse by instability or by stress compressive failure more accurately than traditional DDA analyses, for instance funicular polygons. The numerical results are compared with those of the experiments taken from the literature with, for most cases, very good agreement given the uncertainties on geometry and material properties and given the intrinsic quality dispersion of masonry structures. Collapse loads as function of number of joints, safety factors and limit point forces from the numerical and experimental results are compared. The hinges that appear prior to collapse are also compared, obtaining again for most cases very good agreement., J.L. Perez-Aparicio, R. Bravo were partially supported by the MFOM I+D (2004/38), all authors by MICIIN #BIA-2008-00522 and the first also by Polytechnic University of Valencia under Grant PAID 05-10-2674.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Optimal numerical design of bucket elevators using discontinuous deformation analysis

  • Pérez Aparicio, José Luis
  • Bravo, R.
  • Gómez-Hernández, J. Jaime|||0000-0002-0720-2196
Bucket elevators are efficient machines to transport granular materials in industrial and civil engineering applications. These materials are composed of hundreds, thousands or even more particles, the global behavior of which is defined by contact interactions. The first attempts to analyze the transportation of granular materials were treated by very simple continuum methods that do not take into account these interactions, producing simulations that do not fit the experimental results accurately. Given the internal discontinuity nature of granular media, it is reasonable to use numerical methods to model their behavior, such as discontinuous deformation analysis (DDA)-a member of the discrete element method family that started to be used in the 90s to analyze similar problems. The version of DDA used in the current work treats grains as rigid circular particles with friction, damping and eventually cohesion with the objective of simulating and analyzing in detail the discharge of granular materials with bucket elevators. A deterministic computer code has been implemented and validated against simplified analytical formulae and experimental results taken from the literature. This computer code is then used to obtain optimum two-dimensional bucket geometries under specific working conditions. The optimization aims to maximize transport distance and to minimize remaining material, taking into account bucket velocity and the properties of the grains. The resulting geometries are discussed and compared against standard designs., J.L. Perez-Aparicio, R. Bravo were partially supported by the MFOM I+D (2004/38), both by MICIIN #BIA 2008-00522 and the first also by Polytechnic University of Valencia under grant PAID 05-10-2674. J.J. Gomez-Hernandez was partially supported by MICIIN #CGL 2011-23295.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Non-linear finite element formulation applied to thermoelectric materials under hyperbolic heat conduction model

  • Palma, Roberto
  • Pérez-Aparicio, José L.
  • Taylor, R.L.
In the present work, a three-dimensional, dynamic and non-linear finite element to simulate thermoelectric behavior under a hyperbolic heat conduction model is presented. The transport equations, which couple electric and thermal energies by the Seebeck, Peltier and Thomson effects, are analytically obtained through extended non-equilibrium thermodynamics, since the local equilibrium hypothesis is not valid under the hyperbolic model. In addition, unidimensional analytical solutions are obtained to validate the finite element formulation. Numerically, isoparametric eight-node elements with two degrees of freedom (voltage and temperature) per node are used. Non-linearities due to the temperature-dependence on the transport properties and the Joule effects are addressed with the Newton-Raphson algorithm. For the dynamic problem, HHT and Newmark-ß algorithms are compared to obtain accurate results, since numerical oscillations (Gibbs phenomena) are present when the initial boundary conditions are discontinuous. The last algorithm, which is regularized by relating time steps and element sizes, provides the best results. Finally, the finite element implementation is validated, comparing the analytical and the numerical solutions, and a three-dimensional example is presented., This research was partially supported by the Spanish Ministry of Education through Grant No. FPU AP-2006-02372 and also from Grants MICINN BIA-2008-00522, CSD2008-00037 Canfranc Under-ground Physics, Excelencia Junta Andalucia P08-TEP-03641 and "Ayudas Investigacion" from UPV. The authors would also like to thank Prof. Guillermo Rus for his valuable contributions.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

An energy consistent frictional dissipating algorithm for particle contact problems

  • Bravo Pareja, Rafael
  • Pérez-Aparicio, José L.
  • Laursen, T.A.
An energy frictional dissipating algorithm (EFDA) for time integration of Coulomb frictional impact-contact problems is presented. With the use of the penalty method, and in the context of a conserving framework, linear and angular momenta are conserved, and energy is consistently dissipated. Previously published formulations were stable, forcing the energy dissipation to be monotonic to prevent unstable energy growth. The shortcoming of many was that they were not able to reproduce the real kinematics and dissipation of physical processes, provided by analytical formulations and experiments. EFDA formulates a conserving framework on the basis of a physical energy dissipation estimator. This framework uses an enhanced penalty contact model based on a spring and a dashpot, enforcing physical frictional energy dissipation, controlling gap vibrations, and modifying the velocities and contact forces during each time step. The result is that the dissipated energy, kinematics, and contact forces are consistent with the expected physical behavior. Energy frictional dissipating algorithm has been applied to four rigid-body frictional problems using the discrete element method. The first problem is the analysis of a disk moving on a flat rough surface; the second problem analyzes the kinematics and energy dissipation of elliptical particle impacts. Numerical solutions are compared with analytical ones in both problems. The motion and impact of two disks moving on a semicircular surface are studied in the third problem. Finally, the fourth problem simulates the collapse of a two-dimensional granular column, which is compared with the experimental results., R. Bravo and J. L. Perez-Aparicio were partially supported by the MFOM I+D (2004/38), MICIIN #BIA-2008-00522, and "Ayudas Investigacion" from UPV2010, Polytechnic University of Valencia under program PAID 05-10-2674.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Finite element analysis and material sensitivity of Peltier thermoelectric cells coolers

  • Pérez-Aparicio, José L.
  • Palma, Roberto
  • Taylor, R.L.
In this work, a finite element simulation of a commercial thermoelectric cell, working as a cooling heat pump, is presented. The specially developed finite element is three-dimensional, non-linear in its formulation (using quadratic temperature-dependence on material properties) and fully coupled, including the Seebeck, Peltier, Thomson and Joule effects. Another special interface finite element is developed to prescribe the electric intensity, taking advantage of repetitions and symmetries. A thorough study of the distributions of voltage, temperature and the corresponding fluxes is presented, and the performance of the cell is compared with that of the manufacturer and with simplified analytical formulations, showing a good agreement. Combining the finite element model with the Monte Carlo technique, a sensitivity analysis is presented to take into account the performance dependence on the material properties, geometrical parameters and prescribed values. This analysis, which can be considered a first step to optimize these devices, concludes that the temperature-dependence of the material properties of electric conductivity and Seebeck coefficient is very relevant on cell performance., This research was partially supported by the Ministry of Education through Grant FPU AP-2006-02372 and also from Grants MICINN BIA-2008-00522, MCyT DPI 2002-04472-C02-02 and Excelencia Junta Andalucia P08-TEP-3641.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Incipient sediment transport for non-cohesive landforms by the discrete element method (DEM)

  • Bravo, R.
  • Ortiz Rossini, Pablo
  • Pérez Aparicio, José Luis
[EN] We introduce a numerical method for incipient sediment transport past bedforms. The approach is based on the discrete element method (DEM) [1], simulating the micro-mechanics of the landform as an aggregate of rigid spheres interacting by contact and friction. A continuous finite element approximation [2] predicts the boundary shear stress field due to the fluid flow, resulting in drag and lift forces acting over the particles. Numerical experiments verify the method by reproducing results by Shields [3] and other authors for the initiation of motion of a single grain. A series of experiments for sediments with varying compacity and constituting piles yields enhanced relationships between threshold shear stress and friction Reynolds number, to define incipient sediment transport criterion for flows over small-scale bed morphologies., This work was partially supported by the MICIIN Grants #BIA-2008-00522 and #BIA-2012-32918.