Skip to main content

BASES PARA EL DISEÑO DE ESTRUCTURAS SOSTENIBLES DE HORMIGON DE MUY ALTO RENDIMIENTO A NIVEL PRENORMATIVO

BIA2016-78460-C3-1-R

•
Funding agency name Agencia Estatal de Investigación
Funding agency acronym AEI
Program Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Call Proyectos I+D+i Retos de Investigación
Call year 2016
State Plan 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Beneficiary centre UNIVERSITAT POLITÈCNICA DE VALÈNCIA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 11
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Flexural and compressive creep behavior of UHPFRC specimens

  • Llano-Torre, Aitor
  • Martí Vargas, José Rocío|||0000-0003-1665-2348
  • Serna Ros, Pedro|||0000-0001-8754-1165
[EN] The long term behavior of Ultra High Performance Fiber Reinforced Concrete (UHPFRC) is analyzed in this study. The experimental campaign covered creep in compression and creep in flexure in cracked state. Three types of specimens were cast: cylindrical specimens (empty set100 x 200 mm) for compressive creep and shrinkage, and prismatic specimens type regular "R" (150 x 150 x 600 mm) and type slim "S" (150 x 40 x 600 mm) for flexural creep in cracked state. Specimens R were notched up to 50 mm in depth to weak the central section and then pre-cracked until 0.65 mm of Crack Mouth Opening Displacement (CMOD). Specimens S were pre-cracked unnotched until a loss of 50% of stiffness was observed. Flexural creep tests were performed during 270 days under load, and until 360 days the compressive tests. Measurements from three experimental sources were obtained: CMOD, compressive strains on top of prismatic specimens and longitudinal compressive strains in cylindrical specimens. Creep coefficients and parameters related with deferred deformations velocity were obtained from all three sources. Creep coefficients under flexure at 270 days ranged from 0.62 to 1.20 in the tensile zone, and from 0.72 to 0.90 in the compressive zone. Creep coefficient in compression at one year was 1.07, which is consistent with values found in the literature. Deferred deformations velocities at early ages were greater in specimens R than in specimens S, and a secondary creep stage was achieved in all specimens after 210 days of sustained loading., The authors wish to thank the technicians of ICITECH, where the experimental work was developed. The financial support of the project BIA2016-78460-C3-1-R "Bases para el diseno de estructuras sostenibles de hormigon de muy alto rendimiento a nivel prenormativo/Diseno eficiente de estructuras de HMAR", supported by the Ministry of Economy and Competitiveness (Spain) and the European Regional Development Fund (European Union), is also gratefully acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Comparison of macrosynthetic and steel FRC shear-critical beams with similar residual flexure tensile strengths

  • Ortiz-Navas, Francisco
  • Leiva, Gabriel
  • Navarro-Gregori, Juan|||0000-0002-6319-7029
  • Serna Ros, Pedro|||0000-0001-8754-1165
[EN] This study extends previous experimental research on the shear behaviour of macrosynthetic fibre-reinforced concrete beams and compares them to steel fibre-reinforced concrete beams with similar mechanical and geometrical properties. This work employed two fibre types: 60/0.9 (long/diameter) double hooked-end steel fibre and 60/85 monofilament polypropylene fibre. Beams were tested by shear loading covering parameters, such as two different cross-section widths, two shear-span-to-effective-depth ratios, two fibre types and using repetitions with and without transverse reinforcement. For quantitative comparison purposes, crack pattern evolution was studied along increasing loads levels. Effects were studied by photogrammetry, including influence of fibres on crack propagation in uncracked and dowel zones, influence of fibres on stirrup behaviour, and shear deformation or kinematics of critical shear cracks. The results evidenced similar effectiveness for both fibre types in controlling shear crack propagation and horizontal dowel cracking. Both fibres provided similar shear ductility and shear deflections. Consequently, the authors confirm that residual flexural tensile strengths are a convenient parameter for characterising the shear behaviour of fibre-reinforced concrete beams., This work forms part of Project "BIA2016-78460-C3-1-R" supported by the State Research Agency of Spain.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Tensile behaviour of reinforced UHPFRC elements under serviceability conditions

  • Khorami, M.
  • Navarro-Gregori, Juan|||0000-0002-6319-7029
  • Serna Ros, Pedro|||0000-0001-8754-1165
[EN] Tension stiffening is an essential effect that influences the behaviour of concrete structures under serviceability conditions, mainly regarding crack control and deflection behaviour. Serviceability conditions can be studied experimentally by running the so-called uniaxial tensile test. This paper reports an extensive experimental research conducted to study the tensile behaviour of reinforced Ultra-High Performance Fibre-Reinforced Concrete (R-UHPFRC) under service conditions by uniaxial tensile testing. The parameters studied were the reinforcement ratio and the steel fibre content in a experimental programme including 36 specimens. Special testing equipment and methodology to measure the post-cracking deformation of R-UHPFRC ties were developed, and special attention was paid to the shrinkage effect. The tensile elements' axial stiffness was approximately parallel to the bare bar response after microcracking formation showing a full tension-stiffening response. The average tensile capacity of the reinforced elements (tension stiffening response) was achieved. Concrete's contribution in the R-UHPFRC ties with the tensile properties deriving from four-point bending tests (4PBTs) on non-reinforced UHPFRC specimens was also compared. The experimental results revealed a slight increase in concrete's contribution with the higher reinforcement ratio. Moreover, the concrete's contribution in the tensile elements was higher than the characteristic tensile properties deriving from 4PBTs., This study forms part of Project BIA2016-78460-C3-1-R, supported by the Ministry of Economy and Competitiveness of Spain.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Effects of tension stiffening and shrinkage on the flexural behavior of reinforced UHPFRC beams

  • Mezquida-Alcaraz, Eduardo J.
  • Navarro-Gregori, Juan|||0000-0002-6319-7029
  • Martí Vargas, José Rocío|||0000-0003-1665-2348
  • Serna Ros, Pedro|||0000-0001-8754-1165
[EN] This paper presents a study on the flexural behavior of Ultra-High-Performance Fiber-Reinforced Concrete (UHPFRC) beams, which included conventional reinforcing bars. The study focuses on critical design aspects, such as concrete shrinkage and cracking implications on the tension-stiffening phenomenon. An experimental program with two different sized flexural reinforced UHPFRC beams was run. Beams were cast and tested in a four-point bending test (4PBT) using UHPFRC with different amounts of fibers: 130 and 160 kg/m(3) (1.66% and 2.00% in vol.) to cover a wide range of strain-softening and strain-hardening constitutive UHPFRC behaviors. A nonlinear finite element model (NLFEM) was developed to validate the mechanical tensile characterization of UHPFRC when applied to reinforced elements. Both shrinkage and tension-stiffening effects were considered to improve the model. After the NLFEM simulation, very reliable results were obtained at both the service and ultimate load levels compared to the experimental ones. Finally, some aspects about the design of reinforced UHPFRC cross-sections under bending forces are addressed and satisfactorily compared to the experimental results., This work forms part of Project "BIA2016-78460-C3-1-R" supported by the State Research Agency of Spain and the project "Rethinking coastal defence and Green-energy Service infrastructures through enHancEd-durAbiLity high-performance cement-based materials-ReSHEALience", funded by the European Union Horizon 2020 research and innovation programme under GA No 760824.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Experimental methodology on the serviceability behaviour of reinforced ultra-high performance fibre reinforced concrete tensile elements

  • Khorami, Majid
  • Navarro-Gregori, Juan|||0000-0002-6319-7029
  • Serna Ros, Pedro|||0000-0001-8754-1165
[EN] Design codes include serviceability limit state (SLS) provisions for stress, crack, and deflection control in concrete structures, which may limit the structural design. When drawing on reinforced ultra-high performance fibre-reinforced concrete (R-UHPFRC), the process of cracking differs significantly from traditional concretes. Thus, it remains unclear whether the traditional provisions are applicable to R-UHPFRC or should be reviewed. Uniaxial tensile tie test is an excellent option to analyse and review these criteria. This work proposes a novel test methodology to study the behaviour of R-UHPFRC under serviceability conditions, which lets the study of the global and local deformation behaviour by using different measurement equipment. Two different types of R-UHPFRC ties with variant fibre content were tested. The global average tensile stressstrain curve, cracking behaviour, number, and width of cracks were obtained. Promising preliminary results admitted that this methodology can be useful to propose design criteria of R-UHPFRC under SLS., State Research Agency of Spain, Grant/Award Number: BIA2016-78460-C3-1-R
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Tesis doctoral (DoctoralThesis)

Serviceability Behaviour of Reinforced UHPFRC Tensile Elements

  • Khorami, Majid
[ES] Todas estructuras, especialmente las conformadas con hormigón armado, no solo deben cumplir con la seguridad necesaria bajo los Estados Límites Últimos (ULS), además es imprescindible que garanticen un comportamiento adecuado frente a condiciones de servicio. En general, los requisitos fundamentales de servicio que debe cumplir este tipo de estructuras son: la funcionalidad, comodidad para el usuario y la apariencia. Sin embargo, estos no se pueden verificar de forma directa; por lo tanto, ha sido necesario definir criterios de desempeño tales como control de deflexión, control de vibración y control de agrietamiento para dar cumplimiento a lo indicado anteriormente. Además, se dificulta el cálculo de la capacidad de servicio debido al fenómeno de agrietamiento, el efecto de rigidez por tensión, la contracción y los efectos de fluencia. Por lo tanto, el control de la fisuración en estructuras de hormigón armado generalmente se logra limitando la tensión en el refuerzo de acero y la matriz de hormigón. Siendo así que, en los diseños incluidos en códigos relevantes a hormigón, especifican la tensión máxima del refuerzo de acero después de la fisuración y el ancho máximo de fisura para los miembros estructurales de CR o FRC, no obstante los aspectos de capacidad de servicio del diseño para el hormigón reforzado con fibras de ultra alto rendimiento reforzado (R-UHPFRC), no han sido incluidos en los códigos o recomendaciones de UHPFRC. A pesar de que se han realizado muchos esfuerzos en la investigación tanto experimental como teórica sobre el comportamiento de servicio de los elementos estructurales de CR o FRC durante las últimas décadas, para el R-UHPFRC se debe desarrollar aún más su conocimiento relacionado con los requisitos para el diseño de capacidad de servicio, incluyendo su comportamiento de tensión y agrietamiento. En este marco, el objetivo principal de la presente tesis doctoral es evaluar el comportamiento de servicio de R-UHPFRC. Por tal razón, es fundamental realizar la evaluación del comportamiento de deformación y fisuración de los elementos de tracción R-UHPFRC. Para ello, se abordaron y cumplieron adecuadamente dos puntos principales. El primero, diseñar una metodología de prueba innovadora y adecuada para ejecutar los experimentos requeridos para este proyecto de doctorado. En segundo lugar, se llevó a cabo la evaluación de la respuesta de rigidez a la tensión y el comportamiento de agrietamiento del R-UHPFCR, que son parámetros primordiales para el diseño de capacidad de servicio. Para estudiar estos dos parámetros, se consideraron algunos parámetros importantes tales como: el efecto del volumen del contenido de fibra, el tipo de fibra, el efecto del tamaño, el efecto de la relación de refuerzo y el efecto de la contracción. Finalmente, para evaluar los parámetros mencionados, se presentan cuatro campañas experimentales. Cada una de ellas, representa un nivel diferente de estudio. El primero corresponde a la validación de la metodología de ensayo de tracción propuesta y examinar los datos experimentales obtenidos, para emplearlos en futuros estudios de este proyecto. El segundo nivel consistió en establecer y realizar experimentos completos con dos tipos de fibra de acero, modificando además su cantidad, es así como se utilizaron diferentes proporciones de refuerzo y sección transversal para evaluar el efecto tanto del tamaño como del contenido de fibra, respectivamente. También, en un estudio experimental específico se indagó sobre el efecto de la combinación de micro y microfibras de acero en la deformación y el comportamiento de agrietamiento de los elementos R-UHPFRC de tracción. El tercer nivel corresponde a una prueba de contracción intensiva, necesaria para obtener el valor de contracción del UHPFRC utilizado en esta investigación. El último nivel comprende la modificación de la geometría de la probeta y el uso de probetas en forma de hueso de perro para evaluar el ancho medio y máximo de fisura (valor, [CA] Totes les estructures, especialment les conformades amb formigó armat, no només han de complir amb la seguretat necessària sota els Estats Límits Últims (ULS), a més és imprescindible que garanteixin un comportament adequat davant de condicions de servei. En general, els requisits fonamentals de servei que ha de complir aquest tipus d'estructures són: la funcionalitat, la comoditat per a l'usuari i l'aparença. Això no obstant, aquests no es poden verificar de forma directa; per tant, ha calgut definir criteris d'acompliment com ara control de deflexió, control de vibració i control d'esquerdament per a donar compliment al que s'ha indicat anteriorment. A més, es dificulta el càlcul de la capacitat de servei a causa del fenomen d'esquerdament, l'efecte de rigidesa per tensió, la contracció i els efectes de fluència. Per tant, el control de la fissuració en estructures de formigó armat generalment s'aconsegueix limitant la tensió al reforç d'acer i la matriu de formigó. És així que en els dissenys inclosos en codis rellevants a formigó, especifiquen la tensió màxima del reforç d'acer després de la fissuració i l'amplada màxima de fissura per als membres estructurals de CR o FRC, no obstant els aspectes de capacitat de servei del disseny per al formigó reforçat amb fibres d'ultra alt rendiment reforçat (R-UHPFRC), no han estat inclosos als codis o recomanacions d'UHPFRC. Tot i que s'han realitzat molts esforços en la investigació tant experimental com teòrica sobre el comportament de servei dels elements estructurals de CR o FRC durant les últimes dècades, per al R-UHPFRC s'ha de desenvolupar encara més el seu coneixement relacionat amb els requisits per al disseny de capacitat de servei, incloent el comportament de tensió i esquerdament. En aquest marc, l'bjectiu principal de la present tesi doctoral és avaluar el comportament de servei de R-UHPFRC. Per aquesta raó, és fonamental fer l'avaluació del comportament de deformació i fissuració dels elements de tracció R-UHPFRC. Per això, es van abordar i van complir adequadament dos punts principals. El primer, dissenyar una metodologia de prova innovadora i adequada per executar els experiments requerits per a aquest projecte de doctorat. En segon lloc, es va fer l'avaluació de la resposta de rigidesa a la tensió i el comportament d'esquerdament del R-UHPFCR, que són paràmetres primordials per al disseny de capacitat de servei. Per estudiar aquests dos paràmetres, es van considerar alguns paràmetres importants com ara l'efecte del volum del contingut de fibra, el tipus de fibra, l'efecte de la mida, l'efecte de la relació de reforç i l'efecte de la contracció. Finalment, per avaluar els paràmetres mencionats, es presenten quatre campanyes experimentals. Cadascuna representa un nivell diferent d'estudi. El primer correspon a la validació de la metodologia dassaig de tracció proposada i examinar les dades experimentals obtingudes, per a emprar-les en futurs estudis daquest projecte. El segon nivell va consistir a establir i realitzar experiments complets amb dos tipus de fibra d'acer, modificant-ne a més la quantitat, és així com es van utilitzar diferents proporcions de reforç i secció transversal per avaluar l'efecte tant de la mesura com del contingut de fibra, respectivament. També, en un estudi experimental específic, es va indagar sobre l'efecte de la combinació de micro i macrofibres d'acer en la deformació i el comportament d'esquerdament dels elements R-UHPFRC de tracció. El tercer nivell correspon a una prova de contracció intensiva, necessària per obtenir el valor de contracció de l'UHPFRC utilitzat en aquesta investigació. L'últim nivell comprèn la modificació de la geometria de la proveta i l'ús de provetes en forma d'os de gos per avaluar l'amplada mitjana i màxima de fissura (valor real detectat) provocat per esforços de tracció en els elements de tracció R-UHPFRC . És important esmentar que es van fer diferents anàlisis per a cada investigació experimental i es van ac, [EN] All structures, particularly reinforcement concrete structures, apart from meeting necessary security against Ultimate Limit States (ULS), must exhibit appropriate behaviour under service conditions. Generally, the fundamental serviceability requirements that concrete structures should meet are functionality, user comfort and appearance. These requirements cannot, however, be directly checked. Therefore, performance criteria, such as deflection control, vibration control and cracking control, are defined to meet these requirements. Serviceability calculation is complicated because of the cracking phenomenon, the tension stiffening effect, shrinkage, and creep effects. Cracking control in reinforced concrete (RC) structures is generally achieved by limiting stress in steel reinforcement and the concrete matrix. Many concrete code designs specify a maximum steel reinforcement stress after cracking and a maximum crack width for RC or fibre-RC (FRC) structural members, while the design serviceability aspects for Reinforced Ultra-High Performance Fibre-Reinforced Concrete (R-UHPFRC) are poorly considered in UHPFRC codes or recommendations. Many efforts have been made in experimental and theoretical research into the serviceability behaviour of RC or FRC structural elements in the last few decades. However, for R-UHPFRC, knowledge about tension and cracking behaviour must improve and serviceability design requirements have to be further studied. Within this framework, the main purpose of the present PhD thesis is to evaluate the serviceability behaviour of R-UHPFRC. For this purpose, the evaluation of the deformation and cracking behaviour of R-UHPFRC tensile elements is essential. To that end, two main items were addressed and adequately met. The first one was to design an innovative and adequate test methodology to carry out the experiments required for this PhD project. The second involved evaluating the tension stiffening response and cracking behaviour of R-UHPFRC, which are fundamental parameters for R-UHPFRC structures' serviceability design. To study these two parameters, important parameters were considered, such as fibre content, fibre type, size effect, reinforcement ratio and shrinkage effect. In order to evaluate the aforementioned parameters, four experimental campaigns are presented. Each campaign represents a different study level. The first corresponds to the validation of the proposed tensile test methodology and to the examination of the obtained experimental data for future studies required for this PhD project. The second experimental study level corresponds to establishing and undertaking comprehensive experimental programmes with two different steel fibre types and fibre contents. Different cross-section and reinforcement ratios were used to evaluate the size effect and fibre content effect, respectively. The effect of the micro- and macro-steel fibres combination on the deformation and cracking behaviour of tensile R-UHPFRC elements was investigated in a specific experimental study. The third level corresponds to an intensive shrinkage test, which was conducted to obtain the shrinkage value of the UHPFRC used in this PhD study. The final level corresponds to a specific experimental study, done by modifying the specimen's geometry and using the dog bone-shaped specimens to evaluate the average and maximum crack width (real detected value) caused by tensile stresses in R-UHPFRC tensile elements. It is worth mentioning that different analyses were performed for each experimental research and appropriate results were achieved to fulfil the thesis aims. Keywords: cracking behaviour, design criteria, durability, fragility curve, post-cracking tensile stiffness, serviceability behaviour, shrinkage, SLS requirements, structural design, tensile elements, tension stiffening, test method, tie, UHPFRC., This work is part of Project “BIA2016-78460-C3-1-R” supported by the State Research Agency of Spain
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Capítulo o parte de un libro (BookPart)

Comportamiento diferido en estado fisurado de elementos de UHPFRC a flexotracción

  • Llano-Torre, Aitor
  • López, Juan
  • Martí Vargas, José Rocío|||0000-0003-1665-2348
  • Serna Ros, Pedro|||0000-0001-8754-1165
[ES] En este trabajo se analiza el comportamiento a largo plazo de elementos de Hormigón de Ultra Alta Resistencia Reforzados con Fibras (en inglés UHPFRC) mediante una campaña experimental con tres tipos de probetas: cilíndricas (Ø100x200mm), prismáticas “R” (150x150x600mm) y prismáticas “S” (150x40x600mm). Se realizaron ensayos de retracción y de fluencia a flexión en estado fisurado, así como de caracterización tanto a resistencia a compresión como flexotracción. Las probetas cilíndricas se destinaron a retracción, fluencia en compresión y resistencia a compresión simple, en tanto que las prismáticas se destinaron a fluencia en flexión y resistencia a flexotracción. En las probetas R se realizó una entalla de 50 mm de profundidad y fueron prefisuradas hasta alcanzar un Crack Mouth Opening Displacement (CMOD) de 0,65mm. Las probetas S fueron prefisuradas sin entalla hasta alcanzar una pérdida de rigidez del 50%. Se montaron las probetas en los bastidores de fluencia en donde se mantuvo un nivel de carga del 50% de la resistencia residual obtenida del ensayo de prefisura para las probetas R y un nivel de carga entre el 68% y el 86% para las probetas S. Los ensayos de fluencia en flexión abarcaron 270 días, apreciándose una estabilizando más temprana para las probetas tipo S. De los resultados del ensayo de fluencia se calcularon los coeficientes y se compararon con los propuestos por distintos autores para el UHPFRC, dando como resultado que los valores de fluencia obtenidos de manera experimental son ligeramente menores que los propuestos quedando estos del lado de la seguridad., Los autores agradecen la financiación recibida desde el Ministerio de Economía y Competitividad a través de los Proyectos "BIA2012-35776 (FISNE)” y “BIA2016-78460- C3-1-R (BESHO/DEHMAR)”.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Validation of a non-linear hinge model for tensile behavior of UHPFRC using a Finite Element Model

  • Mezquida-Alcaraz, Eduardo J.
  • Lopez Martinez, Juan Angel
  • Navarro-Gregori, Juan|||0000-0002-6319-7029
  • Serna Ros, Pedro|||0000-0001-8754-1165
[EN] Nowadays, the characterization of Ultra-High Performance Fiber-Reinforced Concrete (UHPFRC) tensile behavior still remains a challenge for researchers. For this purpose, a simplified closed-form non-linear hinge model based on the Third Point Bending Test (ThirdPBT) was developed by the authors. This model has been used as the basis of a simplified inverse analysis methodology to derive the tensile material properties from load-deflection response obtained from ThirdPBT experimental tests. In this paper, a non-linear finite element model (ELM) is presented with the objective of validate the closed-form non-linear hinge model. The state determination of the closed-form model is straightforward, which facilitates further inverse analysis methodologies to derive the tensile properties of UHPFRC. The accuracy of the closed-form non-linear hinge model is validated by a robust non-linear FEM analysis and a set of 15 Third-Point Bending tests with variable depths and a constant slenderness ratio of 4.5. The numerical validation shows excellent results in terms of load-deflection response, bending curvatures and average longitudinal strains when resorting to the discrete crack approach., This work forms part of Project "BIA2016-78460-C3-1-R" supported by the State Research Agency of Spain
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Direct procedure to characterize the tensile constitutive behavior of strain-softening and strain-hardening UHPFRC

  • Mezquida-Alcaraz, Eduardo J.
  • Navarro-Gregori, Juan|||0000-0002-6319-7029
  • Serna Ros, Pedro|||0000-0001-8754-1165
[EN] There is a need to establish a complete process to characterize Ultra-High-Performance Fiber-Reinforced Concrete (UHPFRC) in both strain-hardening and strain-softening tensile behavior. This process should be simple and easy to apply so that its application is direct. Therefore, this paper presents the development of a complete process to obtain the tensile constitutive parameters of UHPFRC. A simplified inverse analysis based on four-point bending tests (4PBT) to derive the tensile material properties of strain-hardening UHPFRC was adapted to be applied in the event of strain softening using a nonlinear finite element model (NLFEM). To fulfill this objective, an extensive experimental program was run with 227 UHPFRC specimens tested in 4PBT that exhibited strain-softening and strain-hardening tensile responses. As a reference, the characteristic UHPFRC tensile constitutive behavior was obtained. Finally, a predictive application capable of predicting tensile behavior using the experimental 4PBT curve as input was developed with the experimental database., This work forms part of Project "BIA2016-78460-C3-1-R" supported by the State Research Agency of Spain and the European Union's Horizon 2020 ReSHEALience Project (Grant Agreement No. 760824)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Long-term behavior of cracked fiber reinforced concrete under service conditions

  • Monetti, D.H.
  • Llano-Torre, Aitor
  • Torrijos, M.C.
  • Giaccio, G.
  • Zerbino, Raúl
  • Martí Vargas, José Rocío|||0000-0003-1665-2348
  • Serna Ros, Pedro|||0000-0001-8754-1165
[EN] This paper presents an experimental study on creep behavior of cracked Fiber Reinforced Concrete (FRC). To this end, a conventional strength concrete incorporating hooked-end steel fibers was used. In order to represent service conditions, specimens under low sustained loads with small pre-cracking damage (lower than 0.5 mm) were tested and analyzed. Taking as a reference the residual stress A, determined according to EN 14651:2007, different stress levels for the creep tests were applied: 25%, 35% and 45% of f(R,1). For the pre-cracking damage, several initial crack openings were considered: 0.05, 0.1, 0.2, 0.3 and 0.5 mm. The specimens were tested under a four-point bending scheme for 180 days in controlled environmental conditions. The Crack Opening Rate (COR) was used as parameter to characterize the creep behavior of cracked FRC. After the creep tests, conventional flexural tests were carried out to evaluate the residual capacity and to survey the fiber density of each specimen. Both the stress level and the initial crack opening factors affected significantly the creep behavior. In all cases, the measured increases in crack openings resulted compatible with service conditions, and no negative effects on the residual post-creep behavior were observed. An expression to predict Crack Opening Rate values is proposed. (C) 2018 Elsevier Ltd. All rights reserved., Funding from projects CONICET PIP 112-201101-00765 Development and characterization of fiber reinforced concretes for structural applications , UNLP PPID2012 Damage processes in fiber reinforced concretes , UNLP 11/I188 Fibre reinforced concretes and their contribution to the sustainable development , all three from Argentine, and BIA2016-78460-C3-1-R Bases para el diseño de estructuras sostenibles de hormigón de muy alto rendimiento a nivel prenormativo / Diseño eficiente de estructuras de HMAR , from Spain, as well as the collaboration of Cementos Avellaneda and Maccaferri are greatly appreciated.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Serviceability behaviour of reinforced UHPFRC tensile elements: Assessment of the ratio between maximum and average crack widths

  • Khorami, M.
  • Navarro-Gregori, Juan|||0000-0002-6319-7029
  • Serna Ros, Pedro|||0000-0001-8754-1165
[EN] This study aimed to evaluate the maximum crack width formed under tensile stresses for two reinforced ultrahigh performance fibre-reinforced concrete (UHPFRC) types with different steel fibre volume contents, and to compare them to average values. The maximum crack width values can more than double the average ones based on the applied tensile strain. The difference between maximum and average crack widths should be considered for examining UHPFRC structures for the serviceability and durability design. This paper also introduces appropriate statistical procedures for developing fragility curves based on cracking data by assuming that they can be represented by Rice distribution functions., This study forms part of Project BIA2016-78460-C3-1-R, supported by the Ministry of Economy and Competitiveness of Spain.