Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 6
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Green Composites from Partially Bio-Based Poly(butylene succinate-co-adipate)-PBSA and Short Hemp Fibers with Itaconic Acid-Derived Compatibilizers and Plasticizers

  • Dolza, Celia
  • Gonga, Eloi
  • Fages, Eduardo
  • Tejada-Oliveros, Ramón
  • Balart, Rafael|||0000-0001-5670-7126
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
[EN] In this work, green composites have been developed and characterized using a bio-based poly-meric matrix such as BioPBSA and the introduction of a 30 wt.% short hemp fibers as a natural reinforcement to obtain materials with maximum environmental efficiency. In order to increase the interfacial adhesion between the matrix and the fiber to obtain better properties in the com-posites, a reactive extrusion process have been carried out. On the one hand, different additives derived from bio-based itaconic acid have been added to the BioPBSA/HEMP composite, such as Dibutyl itaconate (DBI) and a copolymer of PBSA grafted with itaconic acid (PBSA-g-IA). On the other hand, a different copolymer of PBSA grafted with maleic anhydride (PBSA-g-MA) was also tested. The resulting composites have been processed by injection-molding to obtain different samples which were evaluated in terms of mechanical, thermal, chemical, dynamic-mechanical, morphological and wettability and color properties. In relation to the mechanical properties, the incorporation of hemp fibers has resulted in an increase in the stiffness of the base polymer. The tensile modulus of pure BioPBSA has increased from 281 MPa to 3482 MPa with 30% fiber. The addition of DBI shows a remarkable improvement in the ductility of the composites, while co-polymers with IA and MA, generate mechanically balanced composites. In terms of thermal properties, the incorporation of hemp fibre and compatibilising agents leads to a reduction in thermal stability. However, from the point of view of thermomechanical properties, a clear in-crease in rigidity is achieved throughout the temperature range studied. As far as the colour of the samples is concerned, the incorporation of hemp generates a typical colour, while the incorpora-tion of the compatibilising agents does not modify this colour excessively. Finally, the introduc-tion of lignocellulosic fibers greatly affects water absorption and contact angle, although the use of additives helped to mitigate this effect., Project with grant number PID2020-116496RB-C22 funded by the Ministry of Science and Innovation MCIN/AEI/10.13039/501100011033, and grant number AICO/2021/025 funded by Generalitat Valenciana. AITEX wants to thank CDTI (Centro para el Desarrollo Tecnológico Industrial) within the framework of grants for Technological Centres of Excellence Cervera (CER-20211013).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

The Effect of Varying the Amount of Short Hemp Fibers on Mechanical and Thermal Properties of Wood Plastic Composites from Biobased Polyethylene Processed by Injection Molding

  • Dolçà, Celia
  • Fages, Eduardo
  • Gonga, Eloi
  • Garcia-Sanoguera, David|||0000-0002-1923-9519
  • Balart, Rafael|||0000-0001-5670-7126
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
[EN] Biobased HDPE (bioHDPE) was melt-compounded with different percentages (2.5 to 40.0 wt.%) of short hemp fibers (HF) as a natural reinforcement to obtain environmentally friendly wood plastic composites (WPC). These WPC were melt-compounded using a twin-screw extrusion and shaped into standard samples by injection molding. To improve the poor compatibility between the high non-polar BioHDPE matrix and the highly hydrophilic lignocellulosic fibers, a malleated copolymer, namely, polyethylene-graft-maleic anhydride (PE-g-MA), was used. The addition of short hemp fibers provided a remarkable increase in the stiffness that, in combination with PE-g-MA, led to good mechanical performance. In particular, 40 wt.% HF drastically increased the Young¿s modulus and impact strength of BioHDPE, reaching values of 5275 MPa and 3.6 kJ/m2, respectively, which are very interesting values compared to neat bioHDPE of 826 MPa and 2.0 kJ/m2. These results were corroborated by dynamic mechanical thermal analysis (DMTA) results, which revealed a clear increasing tendency on stiffness with increasing the fiber loading over the whole temperature range. The crystal structure was not altered by the introduction of the natural fibers as could be seen in the XRD patterns in which mainly the heights of the main peaks changed, and only small peaks associated with the presence of the fiber appeared. Analysis of the thermal properties of the composites showed that no differences in melting temperature occurred and the non-isothermal crystallization process was satisfactorily described from the combined Avrami and Ozawa model. As for the thermal degradation, the introduction of HF resulted in the polymer degradation taking place at a higher temperature. As for the change in color of the injected samples, it was observed that the increase in fiber generated a clear modification in the final shades of the pieces, reaching colors very similar to dark woods for percentages higher than 20% HF. Finally, the incorporation of an increasing percentage of fibers also increased water absorption due to its lignocellulosic nature in a linear way, which drastically improved the polarity of the composite., Project with grant number PID2020-116496RB-C22 funded by the Ministry of Science and Innovation MCIN/AEI/10.13039/501100011033 and grant number AICO/2021/025 funded by Generalitat Valenciana. European Regional Development Fund (ERDF) from the European Union for co-funding the project NABITEX Innovative technical textiles based on SUDOE natural fibers to be applied in Habitat Sector through the Interreg SUDOE Program (SOE2/P1/P0524) and CDTI (Centro para el Desarrollo Tecnológico Industrial) within the framework of grants for Technological Centres of Excellence Cervera (CER-20211013).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Development and Characterization of High Environmentally Friendly Composites of Bio-Based Polyamide 1010 with Enhanced Fire Retardancy Properties by Expandable Graphite

  • Marset, David
  • Fages, Eduardo
  • Gonga, Eloi
  • Ivorra-Martinez, Juan|||0000-0001-8968-4899
  • Sanchez-Nacher, Lourdes|||0000-0002-8627-4576
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
[EN] Bio-based polyamide 1010 was melt-compounded with different percentages (2.5 to 10.0 wt.%) of expandable graphite (EGr) as an environmentally friendly solution to improve the flame retardancy properties. The mechanical, morphological, thermal and fire retardancy properties (among others) are analysed. The novelty of the article lies in the use of fully removable polyamide. The effect of the incorporation of EGr in the properties of this polymer was analysed and characterised. The incorporation of EGr into the PA1010 matrix led to very promising results. Mechanically, the EGr provided increased stiffness and a tensile strength up to 7.5 wt.%, verifying good mechanical performance. The DMTA results also show how the incorporation of EGr in the PA1010 matrix clearly increases the stiffness of the composites over the entire temperature range analysed. In terms of physical properties, water absorption of PA1010 was reduced particularly in the 10% EGr, which reduces the water absorption of PA1010 by 20%. In terms of flame retardant properties, with the incorporation of EGr, a significant reduction in the heat release rate (HRR) values as the concentration of the additive increases and a reduction in the maximum peak heat release rate (pHRR) can be observed for all compounds. In particular, it goes from 934 kW/m2 for neat polyamide to a value of 374 kW/m2 with 10% EGr. Finally, an improvement in the UL-94 rating of the 7.5 and 10% EGr composites was also observed, going from V-2 in the PA to V-1 in these composites, Project with grant number PID2020-116496RB-C22 funded by the Ministry of Science and Innovation MCIN/AEI/10.13039/501100011033 and grant number AICO/2021/025 funded by Generalitat Valenciana. AITEX wants to thank CDTI (Centro para el Desarrollo Tecnologico Industrial) within the framework of grants for Technological Centres of Excellence "Cervera" (CER-20211013).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Sustainable materials with high insulation capacity obtained from wastes from hemp industry processed by wet-laid

  • Gutiérrez-Moscardó, Ó.
  • Canet, M.
  • Fages, E.
  • Gómez-Caturla, Jaume|||0000-0001-8680-4509
  • Lascano-Aimacaña, Diego Sebastián|||0000-0002-0996-1946
  • Sanchez-Nacher, Lourdes|||0000-0002-8627-4576
[EN] This article reports on the revalorization of hemp waste from the textile industry, focusing on the development of new sustainable materials with high insulating properties. Wet-laid technology was used to manufacture nonwovens with different binding fibers, polylactic acid, and viscose fibers. The characterization of the acoustic insulating capacity was carried out using a Kundt tube, and the thermal insulating performance by measuring the heat transmission resistance (R) and thermal conductivity (lambda). The results showed that the developed nonwovens have lower thermal conductivity values of about 0.027-0.034 W/(m K), were even lower than those of traditional thermal insulating materials, being the sample with 100 g/m(2) of areal density and with a composition of 80% of hemp, 10% of polylactide and 10% of viscose the one with the lowest thermal conductivity (0.027 W/(mK). Their acoustic absorption capacity was around 0.76 at a frequency of 6 kHz, in samples containing high hemp waste (>80 wt%). However, the heterogeneous, discontinuous, and high void density structure that contributes to excellent insulating properties, lead to a decrease in their mechanical properties. This demonstrated that these materials are suitable for substituting traditional materials in insulating applications. Additionally, antifungal tests were carried out. However, hemp nonwovens proved to be inefficient against fungal proliferation., The authors disclosed receipt of the following financial support for research, authorship, and/or publication of this article: This Project is funded by CDTI (Centro para el Desarrollo Tecnologico Industrial) within the framework of grants for Technological Centres of Excellence "Cervera". CER-20211013.
IRTA Pubpro. Open Digital Archive
Publication Artículo científico (JournalArticle)

High Added Value Products from Agroindustrial Residues: Study on Microfibrillated Cellulose for Food Applications

  • Aguiló, Ingrid
  • Albadalejo, P.
  • Gallur, M.
  • Abadias, Maribel
  • Ortiz, Jordi
  • Viñas, I.
  • Lafarga, T.
Waste composition range from simple sugars to complex polysaccharides such as starch, cellulose, and hemicellulose, including more complex sources such as lignin, lipids, and proteins. This composition suggests its use as raw materials that can potentially be valued by different techniques and used as resources for new food additives, leading to economic and environmental benefits. In this work, the extraction and production of microfibrillated cellulose (MFC) as the way forward to valorise agroindustrial residues. The high surface area and aspect ratio, rheological behaviour, water absorption and absence of cytotoxic and genotoxic properties of MFC studied in the present study facilitate its use in food applications as stabilizing and texturizer agent. This work has two main goals: The first goal is the production of MFC using a method based on the combination of green chemical and mechanical pre-treatment of the feedstock followed by a disintegration process of the cellulose obtained from agroindustrial residues. The results revealed that the different MFC obtained have a quality comparable with commercial MFC, which is reported by the determination of the Quality Index (QI). QI values between 50 and 63 are obtained with the agroindustrial subproducts tested. The MFC was also characterized using several techniques such as FTIR, SEM and TGA. The second goal is the MFC validation as thickener agent in food (mayonnaise, peach nectar, strawberry syrup and puree apple). First, a rheological study was carried out to observe the MFC thixotropic behaviour. Second, to evaluate techno-functional properties in-vivo, MFC was compared in terms of functionality with the seven additives commonly used in the industry: tare gum, xanthan gum, guar gum, carrageenan, pectin, agar and gelatine. The results revealed that the sample with 0.1% MFC exhibited a reduced thixotropic behavior compared to the other samples (1, 1.5 and 2%). Compared with commercial gums, MFC exhibits the highest water activity (0.87 ± 0.00) and the most alkaline pH value (10.10 ± 0.01). In the in vivo dietary models, thermal stabilization values after 15 min at 85 °C indicate that gums perform better than MFC and carrageenan in mayonnaise stabilization. This study also reveals that gums are more effective in stabilizing the cloud, while gelatine or MFC-containing samples exhibit a higher cloud volume after 30 min of stabilization. Notably, the cloud suspension of peach nectar with MFC-containing samples compares favorably to the control without gums (20 to 40%). This comprehensive study underscores the potential of MFC as a versatile and eco-friendly alternative in food applications, aligning with the broader goals of sustainable waste management and environmentally conscious practices in the agroindustrial sector., Open Access funding provided thanks to the CRUE-CSIC agreement with Springer Nature., The authors would like to thank the AGRIMAX and AGROMATTER project for funding the research. AGRIMAX is funded by the Bio Based Industries Joint Undertaking under the European Union’s Horizon 2020 Research and Innovation Programme under grant agreement No. 720719. Cervera Network AGROMATTER is a strategic research and development program funded by CDTI State Program for the Generation of Knowledge and Scientific and Technological Strengthening of the R&I System, of the State Plan for Scientific and Technical Research and Innovation 2021–2023. This work was also supported by the CERCA Programme of ‘Generalitat de Catalunya’. The authors thank the support of Mariona Segura in the experimental part. I. Aguiló-Aguayo and T. Lafarga thanks the Spanish Ministry of Economy, Industry, and Competitiveness and the European Social Fund for the Postdoctoral Senior Grants Ramon y Cajal (RYC-2016-19949 and RYC2021-031061-I, respectively)., info:eu-repo/semantics/publishedVersion
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

High Added Value Products from Agroindustrial Residues: Study on Microfibrillated Cellulose for Food Applications

  • Aguiló, Ingrid
  • Albadalejo, P.
  • Gallur, M.
  • Abadias, Maribel
  • Ortiz, Jordi
  • Viñas, I.
  • Lafarga, T.
Waste composition range from simple sugars to complex polysaccharides such as starch, cellulose, and hemicellulose, including more complex sources such as lignin, lipids, and proteins. This composition suggests its use as raw materials that can potentially be valued by different techniques and used as resources for new food additives, leading to economic and environmental benefits. In this work, the extraction and production of microfibrillated cellulose (MFC) as the way forward to valorise agroindustrial residues. The high surface area and aspect ratio, rheological behaviour, water absorption and absence of cytotoxic and genotoxic properties of MFC studied in the present study facilitate its use in food applications as stabilizing and texturizer agent. This work has two main goals: The first goal is the production of MFC using a method based on the combination of green chemical and mechanical pre-treatment of the feedstock followed by a disintegration process of the cellulose obtained from agroindustrial residues. The results revealed that the different MFC obtained have a quality comparable with commercial MFC, which is reported by the determination of the Quality Index (QI). QI values between 50 and 63 are obtained with the agroindustrial subproducts tested. The MFC was also characterized using several techniques such as FTIR, SEM and TGA. The second goal is the MFC validation as thickener agent in food (mayonnaise, peach nectar, strawberry syrup and puree apple). First, a rheological study was carried out to observe the MFC thixotropic behaviour. Second, to evaluate techno-functional properties in-vivo, MFC was compared in terms of functionality with the seven additives commonly used in the industry: tare gum, xanthan gum, guar gum, carrageenan, pectin, agar and gelatine. The results revealed that the sample with 0.1% MFC exhibited a reduced thixotropic behavior compared to the other samples (1, 1.5 and 2%). Compared with commercial gums, MFC exhibits the highest water activity (0.87 ± 0.00) and the most alkaline pH value (10.10 ± 0.01). In the in vivo dietary models, thermal stabilization values after 15 min at 85 °C indicate that gums perform better than MFC and carrageenan in mayonnaise stabilization. This study also reveals that gums are more effective in stabilizing the cloud, while gelatine or MFC-containing samples exhibit a higher cloud volume after 30 min of stabilization. Notably, the cloud suspension of peach nectar with MFC-containing samples compares favorably to the control without gums (20 to 40%). This comprehensive study underscores the potential of MFC as a versatile and eco-friendly alternative in food applications, aligning with the broader goals of sustainable waste management and environmentally conscious practices in the agroindustrial sector., Open Access funding provided thanks to the CRUE-CSIC agreement with Springer Nature., The authors would like to thank the AGRIMAX and AGROMATTER project for funding the research. AGRIMAX is funded by the Bio Based Industries Joint Undertaking under the European Union’s Horizon 2020 Research and Innovation Programme under grant agreement No. 720719. Cervera Network AGROMATTER is a strategic research and development program funded by CDTI State Program for the Generation of Knowledge and Scientific and Technological Strengthening of the R&I System, of the State Plan for Scientific and Technical Research and Innovation 2021–2023. This work was also supported by the CERCA Programme of ‘Generalitat de Catalunya’. The authors thank the support of Mariona Segura in the experimental part. I. Aguiló-Aguayo and T. Lafarga thanks the Spanish Ministry of Economy, Industry, and Competitiveness and the European Social Fund for the Postdoctoral Senior Grants Ramon y Cajal (RYC-2016-19949 and RYC2021-031061-I, respectively)., info:eu-repo/semantics/publishedVersion