Skip to main content

MECANISMOS Y FACTORES AMBIENTALES QUE CONTROLAN EL TRANSPORTE DE GASES A TRAVES DE SUELOS Y ROCAS. IMPLICACION EN EL BALANCE DE CO2 ATMOSFERICO.

CGL2011-25162

•
Funding agency name Ministerio de Ciencia e Innovación
Funding agency acronym MICINN
Program Programa Nacional de Proyectos de Investigación Fundamental
Subprogram Subprograma de Proyectos de Investigación Fundamental no Orientada
Call Proyectos I+D
Call year 2011
State Plan 2008-2011 Plan Nacional de Investigación Científica, Desarrollo e Innovación Tecnológica
Management unit Subdirección General de Proyectos de Investigación
Beneficiary centre UNIVERSIDAD DE ALICANTE

Resultados relacionados

Resultados totales (Incluyendo duplicados): 10
Encontrada(s) 1 página(s)

RUA. Repositorio Institucional de la Universidad de Alicante
Publication Otros (Other)

Effect of pore structure and moisture content on gas diffusion and permeability in porous building stones

  • Benavente, David
  • Pla, Concepción
  • Benavente, David|||/items/93054314-55c1-4e9f-a84d-f461370acc10
  • Pla, Concepción|||/items/f9ff3ff5-c55e-4c85-83c1-f71fff810219
Hazardous gases in buildings are a concern for public health and security. These gases can be released from the building materials to indoor air and their concentration may become critical where ventilation is hindered, as such in hypogean or more energetically efficient airtight constructions. Furthermore, the gas ventilation and the indoor gas concentration can considerably increase by the vapour condensation on the ceiling and walls of buildings. In this paper, we characterise the CO2 gas diffusion for a representative range of building porous stones with the aim of establishing the effect of the water content in the gaseous diffusion coefficient. We propose a new methodology to measure gas diffusion with a laboratory device that works under different hygrometric conditions. Results reveal water pore condensation reduces both connected porosity and pore size and therefore, the CO2 diffusion coefficient. This variation occurs in all the studied porous building stones although it is especially important in stones with small pores. Thus, the reduction of CO2 diffusion coefficient for the stone with thinnest pores is by 50% when relative humidity varies from 20 to 90%. Permeability and gas diffusion coefficients present similar trends. Porous stones with larger pores and higher porosity values present the highest CO2 diffusion, water and gas permeability coefficients. Pore size is the conclusive parameter within the transport coefficients. It greatly affects both the tortuosity factor of the CO2 gaseous diffusion and the slip parameter of the Klinkenberg’s model for gas permeability coefficient. Finally, for studied samples, we establish a power regression, which correlates thoroughly both coefficients.
RUA. Repositorio Institucional de la Universidad de Alicante
Publication Otros (Other)

Carbonates and Sulfates in Hot Spring Microbialites (Baños de Mula, Betic Range)

  • García del Cura, María Ángeles
  • Sanz Montero, María Esther
  • Benavente, David
  • Ordóñez Delgado, Salvador
  • Benavente, David|||/items/93054314-55c1-4e9f-a84d-f461370acc10
In this paper the association of various minerals, mainly carbonates, to microbial mats that cover the surfaces of a hot spring is documented. In addition, the influence of microorganisms in the formation of the travertine is discussed.
RUA. Repositorio Institucional de la Universidad de Alicante
Publication Otros (Other)

Predicting water permeability in sedimentary rocks from capillary imbibition and pore structure

  • Benavente, David
  • Pla, Concepción
  • Cueto Mendoza, Nora
  • Galvañ Cortés, Sandra
  • Martínez Martínez, Javier
  • García del Cura, María Ángeles
  • Ordóñez Delgado, Salvador
  • Benavente, David|||/items/93054314-55c1-4e9f-a84d-f461370acc10
  • Pla, Concepción|||/items/f9ff3ff5-c55e-4c85-83c1-f71fff810219
In this paper, absolute water permeability is estimated from capillary imbibition and pore structure for 15 sedimentary rock types. They present a wide range of petrographic characteristics that provide degrees of connectivity, porosities, pore size distributions, water absorption coefficients by capillarity and water permeabilities. A statistical analysis shows strong correlations among the petrophysical parameters of the studied rocks. Several fundamental properties are fitted into different linear and multiple expressions where water permeability is expressed as a generalized function of the properties. Some practical aspects of these correlations are highlighted in order to use capillary imbibition tests to estimate permeability. The permeability–porosity relation is discussed in the context of the influence of pore connectivity and wettability. As a consequence, we propose a generalized model for permeability that includes information about water fluid rate (water absorption coefficient by capillarity), water properties (density and viscosity), wetting (interfacial tension and contact angle) and pore structure (pore radius and porosity). Its application is examined in terms of the type of pores that contribute to water transport and wettability. The results indicate that the threshold pore radius, in which water percolates through rock, achieves the best description of the pore system. The proposed equation is compared against Carman–Kozeny's and Katz–Thompson's equations. The proposed equation achieves very accurate predictions of the water permeability in the range of 0.01 to 1000 mD.
RUA. Repositorio Institucional de la Universidad de Alicante
Publication Otros (Other)

Caracterización petrográfica y petrofísica de la roca encajante de la Cueva del Rull (Vall d'Ebo, Alicante)

  • Carvalho, L. de
  • Pla, Concepción
  • Galvañ Cortés, Sandra
  • Cuevas González, Jaime
  • Andreu Rodes, José Miguel
  • Cañaveras, Juan C.
  • Benavente, David
  • Andreu Rodes, José Miguel|||/items/b5bb0404-d3d6-4a83-a783-ce1c7ba8fc74
  • Benavente, David|||/items/93054314-55c1-4e9f-a84d-f461370acc10
  • Cañaveras, Juan C.|||/items/a5988686-5d8d-4ce2-8f43-a9c27df34477
  • Cuevas González, Jaime|||/items/55ae74d1-5bc1-4dd0-959c-e684d41fe665
  • Pla, Concepción|||/items/f9ff3ff5-c55e-4c85-83c1-f71fff810219
La Cueva del Rull se encuentra en el sector nororiental de la Cordillera Bética, en el denominado Prebético Externo de Alicante (Azema 1977). Regionalmente, la zona de estudio está dominada por la dinámica compresiva de los materiales calizos existentes (Cretácico Superior) afectados, desde el Mioceno Medio y durante el Mioceno Superior, por diversos movimientos tectónicos a partir de los cuales se origina la Depresión de la Vall d'Ebo. Esta fosa tectónica, cuyos bordes norte y sur quedan delimitados por fallas normales con dirección aproximada E-O, está rellena por materiales rudíticos de edad Mioceno Superior, predominantemente conglomeráticos, de espesor variable (decenas a más de 100 metros), localmente plegados y depositados sobre margas de facies “tap” (margas mal estratificadas de carácter arcillo-limoso, desagregadas y de color blanquecino en superficie, cuya edad se atribuye al Mioceno Medio).
RUA. Repositorio Institucional de la Universidad de Alicante
Publication Otros (Other)

Experimental relationship between water permeability and capillarity imbibition in porous rocks

  • Pla, Concepción
  • Galvañ Cortés, Sandra
  • Martínez Martínez, Javier
  • Cueto Mendoza, Nora
  • García del Cura, María Ángeles
  • Ordóñez Delgado, Salvador
  • Benavente, David
  • Benavente, David|||/items/93054314-55c1-4e9f-a84d-f461370acc10
  • Pla, Concepción|||/items/f9ff3ff5-c55e-4c85-83c1-f71fff810219
The movement of fluid through porous systems in rocks has been widely studied in several fields of research such as ground water, petroleum engineering, engineering geology, soil physics and building materials.
RUA. Repositorio Institucional de la Universidad de Alicante
Publication Otros (Other)

Thermodynamic calculations for the salt crystallisation damage in porous built heritage using PHREEQC

  • Benavente, David
  • Brimblecombe, Peter
  • Grossi, Carlota M.
  • Benavente, David|||/items/93054314-55c1-4e9f-a84d-f461370acc10
This work considers the crystallisation mechanisms of the most common and aggressive salts that generate stress in porous building stones as a result of changing ambient conditions. These mechanisms include the salt crystallisation that result from decreasing relative humidity and changes in temperature and, in hydrated salts, the dissolution of the lower hydrated form and the subsequent precipitation of the hydrated salt. We propose a new methodology for thermodynamic calculations using PHREEQC that includes these crystallisation mechanisms. This approach permits the calculation of the equilibrium relative humidity and the parameterization of the critical relative humidity and crystallisation pressures for the dissolution–precipitation transitions. The influence of other salts on the effectives of salt crystallisation and chemical weathering is also assessed. We review the sodium and magnesium sulphate and sodium chloride systems, in both single and multicomponent solutions, and they are compared to the sodium carbonate and calcium carbonate systems. The variation of crystallisation pressure, the formation of new minerals and the chemical dissolution by the presence of other salts is also evaluated. Results for hydrated salt systems show that high crystallisation pressures are possible as lower hydrated salts dissolve and more hydrated salts precipitate. High stresses may be also produced by decreasing temperature, although it requires that porous materials are wet for long periods of time. The presence of other salts changes the temperature and relative humidity of salt transitions that generates stress rather than reducing the pressure of crystallisation, if any salt has previously precipitated. Several practical conclusions derive from proposed methodology and provide conservators and architects with information on the potential weathering activity of soluble salts. Furthermore, the model calculations might be coupled with projections of future climate to give as improved understanding of the likely changes in the frequency of phase transitions in salts within porous stone.
RUA. Repositorio Institucional de la Universidad de Alicante
Publication Otros (Other)

A comparison of experimental methods for measuring water permeability of porous building rocks, Comparación de métodos experimentales para medir la permeabilidad al agua en rocas de construcción porosas

  • Galvañ Cortés, Sandra
  • Pla, Concepción
  • Cueto Mendoza, Nora
  • Martínez Martínez, Javier
  • García del Cura, María Ángeles
  • Benavente, David
  • Benavente, David|||/items/93054314-55c1-4e9f-a84d-f461370acc10
  • Pla, Concepción|||/items/f9ff3ff5-c55e-4c85-83c1-f71fff810219
This paper compares different experimental methods for measuring water permeability in 17 different porous building rocks. Both commercial apparatus and specially made designed permeameters are used for characterising intrinsic permeability and hydraulic conductivity, k, of rocks in the range of 10−12 to 10−4 m/s (~ 10−19−10−11 m2 or ~ 10−4−104 mD). We use both falling head and constant head permeameter methods including the triaxial and modified triaxial tests and a classical constant head permeameter. Results showed that for very low and low permeability samples (k<10−6 m/s), triaxial conditions were found the most accurate procedures and they provided similar or slightly lower permeability values than constant and falling head methods. The latter techniques were highly recommended for permeable and high permeable porous building materials. Water permeability values were also linked to effective porosity and interpreted in terms of interparticle and vugs porosity. Finally, some modifications in the apparatus and procedures were carried out in order to assess water permeability in soft materials, which involve the use of non-saturated samples.
RUA. Repositorio Institucional de la Universidad de Alicante
Publication Otros (Other)

Revisión de los modelos hidrogeoquímicos de génesis de tobas calcáreas, Hydrochemical models of calcareous tuffs: A review

  • Ordóñez Delgado, Salvador
  • Benavente, David
  • Benavente, David|||/items/93054314-55c1-4e9f-a84d-f461370acc10
Los depósitos tobáceos en aguas dulces están ampliamente representados en la Península Ibérica, la mayoría de ellos relacionados con surgencias de acuíferos carbonáticos. Una gran parte de los modelos geoquímicos de la hidroquímica de las aguas en las que se generan dichos depósitos, se basan en suponer que el agua meteórica, previamente enriquecida en CO2 por la existencia de actividad microbiológica en el suelo, fluye a través de la porosidad y de las fracturas de un acuífero de calizo. El agua resultante tiene una naturaleza bicarbonatada cálcica. El reequilibrio con la pCO2 atmosférica después de la surgencia, por agitación del agua, o por acción metabólica de microorganismos fotosintéticos, da lugar a una amplia variedad de facies de tobas calcáreas. Sin embargo, la modelización hidrogeoquímica no ha sido completamente tratada y las condiciones geológicas del entorno no han sido consideradas en sistemas tobáceos generados en zonas de infiltración, en los que el suelo presenta bajas concentraciones de CO2 o cuando la naturaleza de las aguas no son bicarbonatadas cálcicas, sino Ca-Mg-SO4-HCO3. En este trabajo se muestran resultados hidrogeoquímicos de dos ejemplos muy importantes de sistemas tobáceos, actuales y fósiles: río Júcar (Valdeganga- Presa de la Central Hidroeléctrica del Bosque) y río Guadiana Alto (lagunas de Ruidera). Dichos resultados son comparados con otras surgencias kársticas estudiadas recientemente en áreas próximas. La naturaleza del agua del río Júcar y lagunas de Ruidera muestra unas facies hidroquímicas Ca-Mg-SO4-HCO3. Por lo tanto, la interpretación hidrogeoquímica no puede hacerse usando exclusivamente el sistema CO2–H2O– calcita, el cual por otra parte, ha sido utilizado eficazmente en estudios de tasas de precipitación en sistemas tobáceos, así como en la interpretación del registro paleoclimático de la tobas calcáreas, o en reacciones de karstificación de acuíferos calizos. En esta revisión evaluamos la influencia en la hidroquímica de las aguas de las reacciones de dedolomitización y la disolución del yeso en acuíferos dolomítico – yesíferos, las cuales son independientes de la presión parcial de CO2, así como la cinética y sostenibilidad del proceso en términos de génesis de sistemas tobáceos. También consideramos otras reacciones dependientes de CO2, tales como la calcificación del yeso y la disolución y precipitación de calcita por mezcla de aguas. Los modelos apuntados explican la naturaleza de las aguas de los acuíferos dolomítico - yesíferos, además de su gran potencial para generar sistemas tobáceos, poniendo en cuestión el argumento de suelos con horizontes húmicos bien desarrollados, no muy comunes en áreas áridas o semi-áridas. Finalmente, examinamos los efectos sobre el grado de saturación calcita y, por lo tanto, de su influencia en la formación de tobas de la mezcla de aguas procedente de acuíferos multicapa o compartimentados temporalmente.
RUA. Repositorio Institucional de la Universidad de Alicante
Publication Otros (Other)

KarsTS: an R package for microclimate time series analysis

  • Sáez, Marina
  • Pla, Concepción
  • Cuezva Robleño, Soledad
  • Benavente, David
  • Benavente, David|||/items/93054314-55c1-4e9f-a84d-f461370acc10
  • Pla, Concepción|||/items/f9ff3ff5-c55e-4c85-83c1-f71fff810219
KarsTS 2.2 is free, open-source, R-based software for microclimate time series, especially suited to the study of underground or highly insulated environments. The time series of interest include air temperature, humidity, and CO2 and 222Rn content, amongst others. These time series usually pose problems such as gaps, outliers, noise or relative shortness. KarsTS was born as a package for gap filling and thus, it offers multiple univariate and multivariate gap-filling tools well suited to these variables. However, as KarsTS was intended to be a self-sufficient program, it soon grew to encompass several tools for linear and nonlinear time series analysis, preprocessing and plotting. Indeed, many of these variables show a nonlinear behavior that is often disregarded; for this reason, we aim to spread and facilitate the use of some methodologically appropriate analysis tools, even amongst researcher that do not feel comfortable using a console. In this paper, we introduce an overview of KarsTS functionality and we show its potential through some practical application examples on four-year time series of temperature from the Rull cave (Spain).
RUA. Repositorio Institucional de la Universidad de Alicante
Publication Otros (Other)

Array measurements adapted to the number of available sensors: Theoretical and practical approach for ESAC method

  • Galiana-Merino, Juan José
  • Rosa Cintas, Sergio
  • Rosa-Herranz, Julio
  • Garrido Manrique, Jesús
  • Peláez Montilla, José Antonio
  • Martino, Salvatore
  • Delgado, Jose
  • Delgado, Jose|||/items/23421faf-57a5-44ec-a169-eadbf91c5ae5
  • Galiana-Merino, Juan José|||/items/2aeffb6f-7a89-465b-a756-a9ca8b74bb42
  • Rosa Cintas, Sergio|||/items/967ed276-3e44-43ac-b590-21d289713571
Array measurements of ambient noise have become a useful technique to estimate the surface wave dispersion curves and subsequently the subsurface elastic parameters that characterize the studied soil. One of the logistical handicaps associated with this kind of measurements is the requirement of several stations recording at the same time, which limits their applicability in the case of research groups without enough infrastructure resources. In this paper, we describe the theoretical basis of the ESAC method and we deduce how the number of stations needed to implement any array layout can be reduced to only two stations. In this way, we propose a new methodology to implement an N stations array layout by using only M stations (M < N), which will be recording in different positions of the original prearranged N stations geometry at different times. We also provide some practical guidelines to implement the proposed approach and we show different examples where the obtained results confirm the theoretical foundations. Thus, the study carried out reflects that we can use a minimum of 2 stations to deploy any array layout originally designed for higher number of sensors.