Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 6
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Foaming of 3D-Printed PLA/CaCO3 Composites by Supercritical CO2 Process for Sustainable Food Contact Materials

  • Faba, Simón
  • Agüero, Ángel
  • Arrieta, Marina P.
  • Martínez, Sara
  • Romero, Julio
  • Torres, Alejandra
  • Galotto, María José
[EN] In the last decade, among the emerging technologies in the area of bioplastics, additive manufacturing (AM), commonly referred to as 3D printing, stands out. This technology has gained great interest in the development of new products, mainly due to its capability to easily produce customized and low-cost plastic products. This work aims to evaluate the effect of supercritical foaming of 3D-printed parts based on a commercial PLA matrix loaded with calcium carbonate, for single-use sustainable food contact materials. 3D-printed PLA/CaCO3 parts were obtained by 3D printing with a 20% and 80% infill, and two infill patterns, rectilinear and triangular, were set for each of the infill percentages selected. Supercritical fluid foaming of PLA/CaCO3 composite printed parts was performed using a pressure of 25 MPa, a temperature of 130 degrees C for 23 min, with a fast depressurization rate (1 s). Closed-cell foams were achieved and the presence of CaCO3 did not influence the surface of the foams or the cell walls, and no agglomerations were observed. Foam samples with 80% infill showed subtle temperature fluctuations, and thermogravimetric analysis showed that samples were thermally stable up to similar to 300 degrees C, while the maximum degradation temperature was around 365 degrees C. Finally, tensile test analysis showed that for lower infill contents, the foams showed lower mechanical performance, while the 80% infill and triangular pattern produced foams with good mechanical performance. These results emphasize the interest in using the supercritical CO2 process to easily produce foams from 3D-printed parts. These materials represent a sustainable alternative for replacing non-biodegradable materials such as Expanded Polystyrene, and they are a promising option for use in many industrial applications, such as contact materials., Simón Faba gratefully acknowledges the National Commission for Scientific and Technological Research, ANID, for its financial support from the Postdoctoral Scholarship abroad (grant number 74230053). Authors thank the financial support of CEDENNA (AFB 220001 Project) and the Spanish Ministry of Science and Innovation (MICINN) through the PID-AEI project (grant PID2021-123753NA-C32) funded by MCIN/AEI/10.13039/501100011033 and by ERDF A way of making Europe by the European Union as well as the TED-AEI project (grant TED-129920A-C43) and Research consolidation project (grant CNS2022-136064) funded by MCIN/AEI/10.13039/501100011033 and by the European Union NextGenerationEU/PRTR . Ángel Agüero acknowledges the Margarita Salas post-doctoral grant from the Ministerio de Universidades, Spain, funded by the Recovery, Transformation, and Resilience Plan financed by the European Union NextGenerationEU. The co-financing of the project FONDECYT-ANID (grant number 1230795) is also acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Biodegradable active packaging films reinforced with thyme waste nanoparticles

  • Sempere-Torregrosa, Jaume|||0000-0002-8742-0301
  • Samper, María-Dolores|||0000-0002-5102-8412
  • Arrieta, Marina Patricia
  • Dominici, F.
  • Debora Puglia, Debora Puglia
  • Torre, Luigi
[EN] This present work introduces a novel strategy combining nanoparticles from thymus vulgaris (nT) infusion waste, incorporated at 1 wt% and 3 wt%, with maleinized corn oil (MCO) as a natural plasticizer into PLA-PHB blend (75 wt% PLA, 25 wt% PHB) The materials were processed by micro-extrusion into films intended for sustainable and biodegradable active packaging applications. Nanoparticle formulation with 3 wt% showed high variation in tensile properties compared to MCO blend with 41% and 75% decrease in tensile strength and elongation at break respectively, otherwise both nanoparticles¿ formulations still exhibit increase on ductile reaching 74% and 49% for 1¿3 wt% on elongation at break compared with neat PLA. Plasticizer effect of MCO and interaction of nT nanoparticles with the blend was confirmed by calorimetric analysis, showing Tg 15% and 9% decrease for 1¿3 wt% respectively. Results of colour and UV characterization suggest that the films could interfere with light incidence while maintaining high transparency. During composting test, it was observed that the addition of nanoparticles delayed the degradation grade, although all samples were composted within 30 days. Furthermore, the nanoparticles improved the oxygen barrier properties of developed films, leading to a reduction of above 40% for both nanoparticles¿ formulations in OTR-e values. In addition, nanoparticles highly increased antioxidant activity with 67% and 75% for 1¿3 wt%, interesting findings to develop sustainable, biodegradable and active materials for food packaging applications., This research was supported by I+D+i PID2021-123753NA-C32 and PID2021-123753NA-C33 projects by MCIN/AEI/https://doi.org/10.13039/501100011033 and by FEDER A way of making Europe , as well as the TED2021-129920 A-C43 and CNS2022-136064 projects by MCIN/AEI/https://doi.org/10.13039/501100011033 and by Unión Europea NextGenerationEU/PRTR.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Effect of Different Porous Size of Porous Inorganic Fillers on the Encapsulation of Rosemary Essential Oil for PLA-Based Active Packaging

  • Cerdá-Gandía, Raúl
  • Agüero, Ángel
  • Arrieta, Marina Patricia
  • Fenollar, Octavio|||0000-0003-4323-7414
[EN] Essential oils are interesting active additives for packaging manufacturing as they can provide the final material with active functionalities. However, they are frequently volatile compounds and can be degraded during plastic processing. In this work Rosmarinus officinalis (RO) essential oil was encapsulated into Diatomaceous earth (DE) microparticles and into Halloysite nanotubes (HNTs) and further used to produce eco-friendly active packaging based on polylactic acid (PLA). PLA-based composites and nanocoposites films based on PLA reinforced with DE + RO and HNTs + RO, respectively, were developed by melt extrusion followed by cast-film, simulating the industrial processing conditions. As these materials are intended as active food packaging films, the obtained materials were fully characterized in terms of their mechanical, thermal and structural properties, while migration of antioxidant RO was also assessed as well as the compostability at laboratory scale level. Both DE and HNTs were able to protect the Rosmarinus officinalis (RO) from thermal degradation during processing, allowing to obtain films with antioxidant properties as demonstrated by the antioxidant assays after the materials were exposed for 10 days to a fatty food simulant. The results showed that incorporating Rosmarinus officinalis encapsulated in either DE or HNTs and the good dispersion of such particles into the PLA matrix strengthened its mechanical performance and sped up the disintegration under composting conditions of PLA, while allowing to obtain films with antioxidant properties of interest as antioxidant active food packaging materials., This research was funded by the Spanish Ministry of Science and Innovation (MICINN) through PID-AEI project (grants PID2020-116496RB-C22 and PID2021-123753NA-C32) funded by MCIN/AEI/10.13039/501100011033 and by ERDF "A way of making Europe" by the "European Union" and TED-AEI Project (grant TED2021-129920A-C43) and Research Consolidator Project (grant CNS2022-136064) funded by MCIN/AEI/10.13039/501100011033 and by the "European Union NextGenerationEU/PRTR". Angel Agueero acknowledges the Margarita Salas postdoctoral grant from the Ministerio de Universidades, Spain, funded by the European Union-Next Generation EU.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Use of bacterial cellulose obtained from kombucha fermentation in spent coffee grounds for active composites based on PLA and maleinized linseed oil

  • Agüero, Ángel
  • Arrieta, Marina P.
  • Lascano-Aimacaña, Diego Sebastián|||0000-0002-0996-1946
  • Ivorra-Martinez, Juan|||0000-0001-8968-4899
  • Gómez-Caturla, Jaume|||0000-0001-8680-4509
  • Balart, Rafael|||0000-0001-5670-7126
[EN] Spent coffee grounds have been successfully used as an alternative infusion for kombucha fermentation (spent coffee kombucha, SCK). The obtained by-product of this fermentation consists of a kombucha bacterial cellulose (KBC) matrix. The bacterial cellulose was also fermented in pristine coffee grounds infusion for comparison (coffee kombucha, CK). The bacterial cellulose obtained from both infusion fermentations (SCK and CK) was used as filler in PLA matrix plasticized with a 5 wt% of maleinized linseed oil (MLO). Two different content of SCK and CK (3 and 5 wt%) were introduced in the PLA-MLO matrix to produce a film using a conical twin-screw microextruder to simulate the industrial processing conditions. The resultant bio-based films were studied in tern of morphological, tensile, and thermal properties, UV¿visible absorption, water vapor permeability, and wettability. The antioxidant activity of the obtained materials was tested in contact with a fatty food simulant demonstrating antioxidant activity. In addition, disintegrability tests under composting conditions confirmed the compostable character of all films. The obtained results suggest the potential applicability of these bio-based materials obtained by the revaluation of HoReCa waste in antioxidant materials with interest as food packaging or for agricultural uses., This research contributes to "The Circular and Regenerative Campus" community from the EELISA European University Alliance. Authors gratefully acknowledge Alcoin for kindly providing the coffee waste recovered at the University canteen of the Industrial Engineering School of the Polytechnic University of Madrid (ETSII-UPM). This research was funded by the Spanish Ministry of Science and Innovation (MICINN) through PID-AEI project (grants PID2020-116496RB-C22 and PID2021-123753NA-C32) funded by MCIN/AEI/10.13039/501100011033 and by ERDF "A way of making Europe" by the "Euro-pean Union" and TED-AEI Projects (grants TED2021-129920A-C43 and TED2021-131762A-I00) and "Consolidaci'on Investigadora" Project (grant CNS2022-136064 funded by MCIN/AEI/10.13039/501100011033 and by the "European Union NextGenerationEU/PRTR". It was also funded by Comunidad de Madrid-CAM ("Ayudas de Estimulo a la Investigaci'on de J'ovenes Doctores de la Universidad Polite'cnica de Madrid", APOYO-JOVENES-21-VUI9G6-56-I7GABQ) and Generalitat Valenciana-GVA grant numbers AICO/2021/025 and CIGE/2021/094. J. Gomez-Caturla wants to thank grant FPU20/01732 funded by MCIN/AEI/10.13039/501100011033 and by ESF Investing in your future. J. Ivorra-Martinez wants to thank FPU19/01759 grant funded by MCIN/AEI/10.13039/501100011033 and by ESF Investing in your future. Meanwhile, Ph.D. 'A. Agueero and Ph.D. D. Lascano acknowledge the Margarita Salas postdoctoral grants from the Ministerio de Uni-versidades, Spain, funded by the European Union-Next Generation EU.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Biodegradable nanocomposite poly(lacticacid) foams containing carvacrol-based cocrystal prepared by supercritical CO2 processing for controlled release in active food packaging

  • Faba, Simón
  • Arrieta, Marina P.
  • Romero, Julio
  • Agüero, Ángel
  • Torres, Alejandra
  • Martínez, Sara
  • Galotto, María José
  • E. Rayón|||0000-0002-0653-2046
[EN] Compounds derived from essential oils have been used in active packaging, but their volatility and degradability negatively affect stability and leads to high release rates. The present study aimed to develop PLA bionanocomposite foams loaded with carvacrol cocrystal by supercritical CO2 and its release into a food simulant for control release in food packaging. For this purpose, 4,4'-bipyridine was used as coformer and carvacrol as active agent. Cocrystallized closed cell foams were obtained using supercritical CO2 and were characterized in terms of their physicochemical and mechanical properties, and release kinetics to a D1 simulant were evaluated as well as the antioxidant ability. A better overall mechanical behavior due to the nanoclay promoting a higher interfacial adhesion with the polymeric matrix was revealed. A higher incorporation of carvacrol was observed in samples with higher C30B content. The incorporated cocrystals showed a decrease of one order of magnitude in the estimated effective diffusion coefficient of carvacrol and showed antioxidant activity. These results suggest that the nanocomposite foam containing carvacrolbased cocrystals could be used in active packaging systems with controlled release characteristics, especially with highly volatile compounds, and can be proposed for other fields such as biomedical applications., This work has been developed in the framework of the project FONDECYT (grant number 12011301), Ph.D. Simon Faba is gratefully acknowledged to the National Commission for Scientific and Technological Research, ANID, for its financial support from the National Doctoral Scholarship (grant number 21200851) . Authors thank the financial support of CEDENNA (AFB 220001 Project) and the Spanish Ministry of Science and Innovation (MICINN) through the PID-AEI project (grant PID2021-123753NA-C32) funded by MCIN/AEI/10.13039/501100011033 and by ERDF "A way of making Europe" by the "European Union". Moreover, authors thank the staff of the Laboratory of Membrane Separation Processes (LabProSeM) , USACH, Santiago (Chile) for their assistance with equipment and CO2 supercritical system. Ph.D. Angel Agueero acknowledges the Margarita Salas post-doctoral grant from the Ministerio de Universidades, Spain, funded by the European Union-Next Generation EU. Marina P. Arrieta thanks "Consolidacion Investigadora" project (grant CNS2022-136064) funded by MCIN/AEI/10.13039/501100011033 and by the "European Union NextGenerationEU/PRTR".
RUA. Repositorio Institucional de la Universidad de Alicante
Publication Otros (Other)

Upcycled papaya leaf waste as functional filler in plasticized polylactic acid and recycled polylactic acid films: Tailoring ductility, UV protection, and compostability for sustainable packaging

  • Cenitagoya Alonso, Natalia
  • Faba, Simón
  • Arrieta, Marina Patricia
  • Beltrán Sanahuja, Ana
  • Valdés, Arantzazu
  • Beltrán Sanahuja, Ana|||/items/e050de26-d5fa-4bc8-8092-760c0d8865d0
  • Valdés, Arantzazu|||/items/4014bcef-f512-4723-8000-650f5d9ad7e9
This study explores the valorisation of papaya leaf waste (LW) as a functional agent in biodegradable films based on a polylactic acid matrix based on 70 wt% of virgin PLA and 30 wt% of reprocessed PLA (PLA/rPLA) further plasticized with acetyl tributyl citrate (ATBC) at 15 wt%. LW was fully characterized in terms of its lignocellulosic composition, thermal stability, and antioxidant properties. It was incorporated at 1 wt%, 3 wt%, and 5 wt% into PLA/rPLA and PLA/rPLA-ATBC blends, which were processed into films by extrusion followed by compression molding. The transparent films exhibited a continuous structure without visible defects. The incorporation of LW reduced light transmission, particularly in the UV range, with the 3 wt% formulation showing the most significant blocking effect. ATBC enhanced filler dispersion, reduced interfacial tension, and improved film flexibility and cohesion. Compared with the control, the PLA/rPLA-ATBC-3%LW formulation demonstrated the best overall performance, increasing elongation at break from 1.3 to 6.9% and tensile strength from 22 to 25 MPa, while reducing Young's modulus from 2040 to 1177 MPa, thus indicating enhanced flexibility without compromising mechanical resistance, together with suitable hydrophobicity for food packaging applications. Thermal and barrier properties remained adequate, while disintegration under composting conditions reached ∼90% of mass loss after 22 days. The PLA–rPLA–ATBC–3%LW formulation emerged as the most promising material, providing an optimal balance of processability, mechanical and optical functionality, and environmental profile. This system supports circular-economy strategies by valorising agro-industrial by-products and broadens range of PLA-rPLA-based materials in different usage scenarios.