Skip to main content

CATALIZADORES AVANZADOS PARA LA CONVERSION DE GAS DE SINTESIS EN COMBUSTIBLES

CTQ2010-17988

•
Funding agency name Ministerio de Ciencia e Innovación
Funding agency acronym MICINN
Program Programa Nacional de Proyectos de Investigación Fundamental
Subprogram Subprograma de Proyectos de Investigación Fundamental no Orientada
Call Proyectos I+D
Call year 2010
State Plan 2008-2011 Plan Nacional de Investigación Científica, Desarrollo e Innovación Tecnológica
Management unit Subdirección General de Proyectos de Investigación
Beneficiary centre AGENCIA ESTATAL CONSEJO SUPERIOR DE INVESTIGACIONES CIENTIFICAS (CSIC)

Resultados relacionados

Resultados totales (Incluyendo duplicados): 12
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

The impact of pre-reduction thermal history on the metal surface topology and site-catalytic activity of Co=SiO2 Fischer Tropsch catalysts

  • Prieto González, Gonzalo|||0000-0002-0956-3040
  • Concepción Heydorn, Patricia|||0000-0003-2058-3103
  • Murciano Martínez, Raúl
  • MARTINEZ FELIU, AGUSTIN|||0000-0002-9974-1567
[EN] For ex-nitrate Co/SiO2 Fischer Tropsch synthesis (FTS) catalysts, the influence of the early thermal treatments during catalyst synthesis on the ultimate catalytic properties is studied without overlapping of particle size effects (d(Co) > 15 nm). The bulk and surface properties of the Co3O4 crystallites in the oxidic catalyst precursors depend on the previous thermal history and are decisive for the oxide reduction kinetics. Even after a homogeneous reduction treatment (673 K, H2 flow), catalysts with different prereduction thermal histories showed dissimilar TOF (per surface Co0 atom) under FTS conditions (493 K, 2.0 MPa). As revealed by CO-TPSR and CO-FTIR, the different surface-specific activitites relate to differences in the surface topology of the Co0 nanoparticles which likely result from the varying reduction kinetics. By tracking the effects of the earlier thermal treatments on the properties of the Co species, this work evidences that the pre-reduction thermal history not only determines metal dispersion and reducibility, but also the ultimate TOF. Such memory effect underscores the significance of a rational design of the entire synthesis and activation procedures to achieve Co-based Fischer Tropsch catalysts with improved activity., This work is funded by the Comision Interministerial de Ciencia y Tecnologia (CICYT) of Spain through the Project CTQ2010-17988/PPQ. The authors are grateful to Dr. S. Agouram (Universidad de Valencia), Dr. M.A. Arribas and Dr. J.L. Jorda (ITQ) for the performance of TEM, H<INF>2</INF>-chemisorption, and in situ XRD experiments, respectively.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

The impact of zeolite pore structure on the catalytic behavior of CuZnAl/zeolite hybrid catalysts for the direct DME synthesis

  • García Trenco, Andrés
  • Valencia Valencia, Susana|||0000-0001-7160-2795
  • MARTINEZ FELIU, AGUSTIN|||0000-0002-9974-1567
[EN] In this work, the influence of the pore structure of 10-ring zeolites used as the methanol dehydration func-tion in CuZnAl(CZA)/zeolite hybrid catalysts was studied for the direct dimethyl ether (DME) synthesis. Tothis purpose, six different 10-ring H-zeolites (ZSM-5, FER, IM-5, TNU-9, MCM-22, ITQ-2) with alike bulkSi/Al ratios (in the 9 14 range) were employed. Additionally, the effect of crystallite size (for ZSM-5) andselective surface dealumination by treatment with oxalic acid (for MCM-22) was also investigated. Whilethe initial activity of the zeolites for methanol dehydration was driven by the concentration of strongBrønsted acid sites, the extent of decay was dictated by the pore structure, which determined the amountand nature of the formed carbon species. When evaluated for direct DME synthesis under methanolsynthesis-controlled conditions, all CZA/zeolite hybrid catalysts (prepared by grinding, CZA:zeolite massratio of 2:1) experienced a decline of CO conversion (and DME yield) with time-on-stream (TOS) due toa gradual loss of the methanol synthesis activity of the Cu-based component. Interestingly, the stabilitywith TOS was the lowest for the hybrid catalysts comprising zeolites with large external surface areas(Sext) such as ITQ-2 and MCM-22. Moreover, for zeolites with similar Sext, the deactivation extent of thehybrid catalysts increased with the concentration of surface Al species (from XPS) in the zeolite. Thus,the delaminated ITQ-2 zeolite (Si/Alsurf= 10.6, Sext= 324 m2/g) produced the less stable hybrid while thatcomprising zeolite TNU-9 (Si/Alsurf= 17.9, Sext= 12 m2/g) displayed the highest stability during the syngas-to-DME experiments. These results suggest that the deterioration of the methanol synthesis activity ofthe CZA catalyst in the hybrid catalysts prepared by grinding is produced by detrimental interactionsbetween zeolitic Al species and Cu sites at the surface-contact between zeolite and CZA particle, Financial support by the Comision Interministerial de Ciencia y Tecnologia (CICYT) of Spain through the Project CTQ2010-17988/PPQ is gratefully acknowledged. A. Garcia-Trenco thanks the Ministerio de Economia y Competitividad (former Ministerio de Ciencia e Innovacion) of Spain for a predoctoral (FPI) scholarship.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Study of the interaction between components in hybrid CuZnAl/HZSM-5 catalysts and its impact in the syngas-to-DME reaction

  • García Trenco, Andrés
  • Vidal Moya, José Alejandro
  • MARTINEZ FELIU, AGUSTIN|||0000-0002-9974-1567
[EN] Hybrid CuZnAl(CZA)/HZSM-5 catalysts were prepared by three mixing methods in order to analyze the possible existence of interactions between components and their impact in the STD process, namely: (a) grinding of powders prior to pelletizing (grinding method), (b) slurrying the two solids in water followed by drying and pelletizing (slurry method), and (c) physical mixture of pre-pelletized components. The materials were characterized by ICP-OES, XRD, N-2 physisorption, H-2-TPR, Al-27 MAS NMR, FTIR-pyridine, and EPR spectroscopy. Detrimental interactions producing a drastic reduction in the amount of available zeolitic Bronsted acid sites were observed for the hybrids prepared by slurry and grinding methods. Such interactions involved, on one hand, the partial blockage of micropores by CZA particles and, on the other hand, an inter-cationic exchange of Cu2+ (and possibly also Zn2+) species. The presence of isolated Cu2+ cations occupying exchange positions in the HZSM-5 zeolite was unambiguously evidenced by EPR spectroscopy. The decrease in Bronsted acidity significantly reduced the activity of the zeolite for dehydrating methanol leading to a much lower efficiency of the corresponding hybrids for DME synthesis at typical STD conditions as compared to the catalyst obtained by simple mixture of pre-pelletized components. (C) 2011 Elsevier B.V. All rights reserved., Financial support by the Comision Interministerial de Ciencia y Tecnologia (CICYT) of Spain through the Project CTQ2010-17988/PPQ is gratefully acknowledged. A. Garcia-Trenco thanks the Ministerio de Ciencia e Innovacion (MICINN) of Spain for a predoctoral (FPI) scholarship.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Direct synthesis of DME from syngas on hybrid CuZnAl/ZSM-5 catalysts: New insights into the role of zeolite acidity

  • García Trenco, Andrés
  • MARTINEZ FELIU, AGUSTIN|||0000-0002-9974-1567
[EN] A commercial HZSM-5 zeolite (Si/Al = 16) was submitted to mild acid treatment and partial exchange of H+ by Na+ and Co2+ cations in order to produce samples with different amounts and strengths of Brensted and Lewis acid sites. The acid properties of the zeolites were determined by both FTIR of adsorbed pyridine and NH3-TPD. Then, hybrid catalysts comprising a CuO/ZnO/Al2O3 (CZA) methanol synthesis catalyst and the original and treated zeolites were prepared in order to analyze the impact of the zeolite acidity in the efficiency of the hybrids for the direct syngas-to-DME process. Independent methanol dehydration experiments on the bare zeolites and syngas-to-DME runs under methanol dehydration-controlled conditions were performed using hybrids with low zeolite concentration (CZA:zeolite mass ratio of 10:1) prepared by mixing the pre-pelletized CZA and zeolite components. The results revealed that both strong Bronsted and EFAL-related strong Lewis acid sites are the likely zeolite active sites for methanol dehydration at the typical syngas-to-DME temperature of 260 degrees C. Interestingly, we have found that different conclusions regarding the effect of zeolite acidity may be reached depending on the specific method used for preparing the hybrid catalysts when the overall syngas-to-DME process becomes controlled by the methanol synthesis rate on the Cu-based catalyst (i.e. using hybrids with a CZA:zeolite mass ratio of 2:1, that is, with an "excess" of acid sites). Thus, for hybrids prepared by mixing the pre-pelletized components, the same CO conversion and product selectivity (with values approaching those predicted by the thermodynamic equilibrium at the studied conditions) with no signs of deactivation during at least 50h on stream was attained irrespective of the zeolite acidity. By contrast, significant differences in catalyst stability were found for hybrids prepared by grinding the component powders prior to pelletizing. This fact points towards the occurrence of detrimental interactions between the CZA and zeolite components during the grinding preparation stage. The kind and extent of such detrimental interactions are tightly related to the properties (i.e. acidity, chemical composition) of the ZSM-5 zeolite. (C) 2011 Elsevier B.V. All rights reserved., Financial support by the Comisión Interministerial de Ciencia y Tecnología (CICYT) of Spain through the Project CTQ2010- 17988/PPQ is gratefully acknowledged. A. García-Trenco thanks the Ministerio de Ciencia e Innovación (MICINN) of Spain for a predoctoral (FPI) scholarship.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Synthesis of a Novel Zeolite through a Pressure-Induced Reconstructive Phase Transition Process

  • Jorda Moret, Jose Luis|||0000-0002-0304-5680
  • Rey Garcia, Fernando|||0000-0003-3227-5669
  • Sastre Navarro, German Ignacio|||0000-0003-0496-6331
  • Valencia Valencia, Susana|||0000-0001-7160-2795
  • Palomino Roca, Miguel|||0000-0003-2983-1038
  • Corma Canós, Avelino|||0000-0002-2232-3527
  • Manjón, Francisco-Javier|||0000-0002-3926-1705
  • Gomis, O.|||0000-0001-6763-0638
  • Segura Garcia del Rio, Alfredo
  • Errandonea, Daniel
  • Lacomba Perales, Raúl
  • Kleppe, Annette K.
  • Jephcoat, Andrew P.
  • Amboage, Mónica
  • Rodríguez-Velamazán, J. Alberto
The first pressure-induced solid-phase synthesis of a zeolite has been found through compression of a common zeolite, ITQ-29 (see scheme, Si yellow, O red). The new microporous structure, ITQ-50, has a unique structure and improved performance for propene/propane separation with respect the parent material ITQ-29., We thank the Diamond Light Source (beamline I15) and Institute Laue-Langevin (beamline D1B) for beamtime allocation, and the Spanish Government (projects MAT2010-21270-C04-01/04, MAT2012-3856-C02-01, CTQ2010-17988/PPQ, Consolider MALTA CSD-2007-00045, Consolider Ingenio Multicat CSD-2009-00050 and program Severo Ochoa SEV-2012-0267), Generalitat Valenciana (Project Prometeo and GVA-acomp-2013-012) and "Vicerrectorado de Innovacion y Desarrollo de la UPV" (PAID-05-2009, project UPV2010-0096) for financial support. G.S. thanks Centro de Calculo (UPV) and Area de Informatica Cientifica (SGAI-CSIC) for Computational facilities. We thank Dr. Vidal-Moya for <SUP>29</SUP>Si-MAS-NMR measurements and T. Portilla for technical support.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Zeolite Rho: a highly selective adsorbent for CO2/CH4 separation induced by a structural phase modification

  • Palomino Roca, Miguel|||0000-0003-2983-1038
  • Corma Canós, Avelino|||0000-0002-2232-3527
  • Jorda Moret, Jose Luis|||0000-0002-0304-5680
  • Rey Garcia, Fernando|||0000-0003-3227-5669
  • Valencia Valencia, Susana|||0000-0001-7160-2795
[EN] Zeolite Rho is able to successfully separate CO2 from CH4 with the highest selectivity ever observed on the basis of pore diameter and surface polarity. The adsorption of CO2 provokes structural changes in the zeolite Rho., We acknowledge financial support from Spanish CICYT (MAT2009-14528-C02-01, CTQ2010-17988/PPQ) and European Project TopCombi (NMP2-CT2005-515792). M.P. thanks CSIC for a JAE doctoral fellowship. The authors thank the referee for the suggestion to carry out structural studies.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

A simple an efficient approach to confine Cu/ZnO methanol synthesis catalysts in the ordered mesoporous SBA-15 silica

  • García Trenco, Andrés
  • MARTINEZ FELIU, AGUSTIN|||0000-0002-9974-1567
The ammonia-driving deposition-precipitation (ADP) method has been applied with the purpose of confining active Cu/ZnO methanol synthesis phases inside the pores of the ordered mesoporous SBA-15 silica. Thus, a series of CuZnx/SBA-15 catalysts with total (Cu + Zn) metal loading of 35 wt% and Cu/Zn mass ratios (x) of 0.5, 1, 2, 4, and 6, as well as a Zn-free Cu/SBA-15 sample, have been prepared. Additionally, a CuZn2/SBA-15 sample (Cu + Zn = 35 wt%, Cu/Zn = 2) prepared by impregnation and a coprecipitated Cu-ZnO-Al2O3 (CZA) catalyst have been prepared as reference. The materials have been characterized by ICP-OES, N2 physisorption, XRD, in situ H2-XRD, TEM, H2-TPR, and N2O chemisorption, and their methanol synthesis activities determined, after in situ H2 reduction, under realistic conditions (533 K, 4.0 MPa, syngas: 66%/30%CO/4%CO2). Copper NPs in CuZnx/SBA-15 (ADP) catalysts with Cu/Zn mass ratios up to 2 were effectively confined within the SBA-15 pores (dCu < 7 nm) while at higher ratios part of Cu formed large particles sizing about 60¿70 nm on the external SBA-15 surface. Similar large Cu NPs were also found for the impregnated catalyst (Cu/Zn = 2). A maximum in the methanol synthesis activity was attained for the catalyst prepared by ADP with Cu/Zn mass ratio of 2. This catalyst displayed a synthesis activity about 14 times higher than the impregnated sample with equal composition and nearly the same activity (per mass of Cu) than the reference CZA catalyst. No direct relationship between the methanol synthesis rate and Cu0 surface area was found for the studied catalysts. Instead, our results strongly suggested that the active sites are located at the Cu0-ZnOx interface, which can be maximized through the effective confinement of Cu0 NPs inside the SBA-15 channels using the simple ADP method., Financial support by the Comision Interministerial de Ciencia y Tecnologia (CICYT) of Spain through the Project CTQ2010-17988/PPQ is gratefully acknowledged. Thanks are also due to Dr. J.L. Jorda (ITQ), for performing the in situ H<INF>2</INF>-XRD experiments. A. Garcia-Trenco thanks the Ministerio de Economia y Competitividad (former Ministerio de Ciencia e Innovacion) of Spain for a predoctoral (FPI) scholarship.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Competitive ultrafast electron and proton transfer reactions within titania and silica mesoporous materials

  • Gil, Michael
  • Organero, Juan Angel
  • Navarro Ruiz, María Teresa
  • Douhal, Abderrazzak
  • Corma Canós, Avelino|||0000-0002-2232-3527
[EN] We report on UV-visible absorption and emission and ultrafast emission dynamics of 7-hydroxyquinoline (7HQ) encapsulated within titania-doped silicates (mesoporous and unstructured) and purely TiO2 nanomaterials. When titania is incorporated as larger (similar to 50 angstrom) nanoparticles (TiO2-MCM41), the stationary spectra and fluorescence decay times are very similar to those of the regular MCM-41 sample (R-MCM41). In turn, the presence of titania domains in MCM-41(Ti-MCM41) leads to a large increase of the ground state population of anionic (A) and zwitterionic (Z) forms of the adsorbed dye. This is explained in terms of the cooperative effect of Ti-OH groups and the MCM-41 framework interacting with the confined structures. The emission spectra in Ti-MCM41 show a partial fluorescence quenching, whereas a complete quenching occurs when the dye is interacting with pure TiO2 materials (mesoporous TiMeso and nonporous P25). A femtosecond emission study revealed a very short lifetime (10-14 ps) of the Z form. This strong emission quenching is assigned to an electron transfer process from the excited dye to the conduction band of TiO2 material. For 7HQ caged within TiMeso pores, this process occurs in 0.1-0.4 and 0.8-1.2 Ps for A and Z forms, respectively. However, for 7HQ/Ti-MCM41, the emission decays become longer (0.3-5 ps). This result is due to the presence of mixed dynamics gated from 7HQ molecules located close to and far from TiO2 domains, reflecting the heterogeneity of the sample and the competition between proton- and electron-transfer processes. Our results suggest negligible contribution of a direct titania excitation in the observed dynamics of the used materials., This work was supported by the MICINN through projects: Consolider Ingenio 2010 (CSD2009-0050, MULTICAT), MAT2008-01609, MAT2011-25472, MAT2009-14528-C02-01, and CTQ2010-17988 (PPQ subprogram). We thank Mr. Mikko Ojala for his help at the early stage of this work.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Tuning the Adsorption Properties of Zeolites as Adsorbents for CO2 Separation: Best Compromise between the Working Capacity and Selectivity

  • García, Edder J.
  • Pérez-Pellitero, Javier
  • Pirngruber, Gerhard D.
  • Jallut, Christian
  • Palomino Roca, Miguel|||0000-0003-2983-1038
  • Rey Garcia, Fernando|||0000-0003-3227-5669
  • Valencia Valencia, Susana|||0000-0001-7160-2795
The choice of an appropriate adsorbent for CO2 separation by pressure-swing adsorption remains a field of intense research. In this work, several FAU and LTA zeolites with different Na contents (Si/Al ratios) are studied for the separation of CO2 from mixtures of CO2, CO, and CH4 by means of breakthrough experiments. The breakthrough experiments were carried out between 1 and 5 bar at 303 K using two feed mixtures: 50/50 (v/v) CO2/CH4 and 75/15/15 (v/v/v) CO2/CH4/CO. The most polar zeolites, i.e., those with high Na content, exhibit the highest adsorption capacity and selectivity for CO2, but their regeneration is difficult; hence, their working capacity is low. The opposite is true for the least polar zeolites, i.e., those with low Na content. In order to quantify the trade-off between the selectivity and working capacity, the Ruthven statistical model (RSM) was used. It satisfactorily reproduced the experimental trends. We, therefore, used the RSM to identify the properties of the adsorbent that lead to an optimal compromise between the working capacity and separation factor. The critical parameter is the concentration of extraframework cations, which, in turn, depends on the framework charge of the zeolites FAU and LTA. The optimal trade-off zone is defined in terms of the Henry constant of CO2 (KCO2). It is found that this zone is placed between KCO2 = 5 × 10 3 and 50 × 10 3 molecules·bar 1·Å 3. This interval corresponds to a heat of adsorption of CO2 at zero coverage between 27 and 32 kJ·mol 1. In our study, this optimal range of Henry constants was achieved for the zeolites Na-USY, SAPO-37, LTA (Si/Al = 5), and EMC-1., M.P., F.R., and S.V. are thankful for financial support by the Spanish Government (MAT2012-38567-C02-01, CTQ2010-17988/PPQ Consolider Ingenio 2010-Multicat CSD-2009-00050, and Severo Ochoa SEV-2012-0267).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

n-Hexadecane hydrocracking Single-Event MicroKinetics on Pt/H-beta

  • Vandegehuchte, Bart D.
  • Thybaut, Joris W.
  • Marin, Guy B.
  • MARTINEZ FELIU, AGUSTIN|||0000-0002-9974-1567
  • Arribas Viana, Maria De Los Desamparados|||0000-0002-5761-288X
[EN] The Single-Event MicroKinetic (SEMK) model constructed for gas-phase hydroconversion of light n-alkanes on large-pore USY zeolites was applied, for the first time, to the hydrocracking of n-hexadecane on a Pt/H-Beta catalyst. Despite the 12-ringed pore channels, shape selectivity was observed in the formation of ethyl side chains. Additionally, heavy feed molecules such as n-hexadecane lead to physisorption saturation of the catalyst pores by strong Van der Waals interactions of the long alkyl chains with the zeolite framework. Intermolecular interactions and packing efficiencies in the pores induce deviations from typical Henry-regime physisorption characteristics as the physisorption selectivity, which is expected to increase with increasing carbon number, appeared to be independent of the latter. Micropore saturation effects were described by the 'size entropy' which quantifies the difference in standard entropy loss between physisorption in the Henry regime and hindered physisorption on a saturated surface. The size entropy is proportional to the catalyst loading with physisorbed species and the adsorbate carbon number. The addition of a size entropy term in the SEMK model, amounting to 102J mol(-1) K-1 for a hexadecane molecule at full saturation, allowed accurately reproducing the contribution of secondary isomerization and cracking reactions, as quantified by means of a contribution analysis. (C) 2012 Elsevier B.V. All rights reserved., This work was funded by the European Research Institute of Catalysis and the European Community’s Sixth Framework Programme. This work was also supported by the Research Board of Ghent University (BOF), the Interuniversity Attraction Poles Programme–Belgian State–Belgian Science Policy and the Long Term Structural Methusalem Funding by the Flemish Government. Financial support by the Comisión Interministerial de Ciencia y Tecnología (CICYT) of Spain through the Project CTQ2010-17988/PPQ is also gratefully acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

The influence of zeolite surface-aluminum species on the deactivationof CuZnAl/zeolite hybrid catalysts for the direct DME synthesis

  • García Trenco, Andrés
  • MARTINEZ FELIU, AGUSTIN|||0000-0002-9974-1567
[EN] The influence of the nature and amount of zeolite-surface Al species on the deactivation behavior ofbifunctional CZA/zeolite hybrid catalysts during the direct DME synthesis (260&#9702;C, 4.0 MPa) from syn-gas (66% H2, 30% CO, 4% CO2) has been studied. To this aim, a series of delaminated ITQ-2 zeolites hasbeen prepared by acid treatment and steaming of an Al-ITQ-2 (Si/Al = 12) sample as well as by impreg-nation of an all-silica Si-ITQ-2 sample with Al(NO3)3(aq.) and calcination, and used as the methanoldehydration function of the hybrids. When prepared by grinding, all the hybrid catalysts experienced aloss of activity with time during the syngas-to-DME reaction under conditions where the synthesis ofmethanol on the copper catalyst (CZA) controlled the overall DME synthesis rate. The decay was neitherrelated to changes in the properties of the Cu species (dispersion, Cu0surface area) nor to depositionof carbon species on the metallic function (as ascertained by TPO) but to a particular mode of deacti-vation of the CZA catalyst due to adverse interactions between the copper component and the zeolite.Interestingly, the extent of the deactivation was seen to increase linearly with a parameter &#711;, arbitrarilydefined as &#711; = Sext× [Al/(Si + Al)]surf× %EFAL/100, where Sextis the external surface area of the zeolite,[Al/(Si + Al)]surfis the relative Al surface concentration (from XPS), and %EFAL is the percentage of penta-and hexacoordinated extraframework Al species with respect to the total Al detected by27Al MAS NMR.The correlation suggests that EFAL species located at the surface contact between the CZA and zeoliteparticles were primarily responsible for this particular mode of deactivation of the copper catalyst. Wehypothesize that EFAL species could migrate to the CZA catalyst during DME synthesis through a water-assisted mechanism, modifying the interaction between Cu and ZnOxat the Cu ZnOxinterface where theactive copper sites are likely located, Financial support by the Comisión Interministerial de Ciencia y Tecnología (CICYT) of Spain through the Project CTQ2010-17988/PPQ is gratefully acknowledged. A. García-Trenco thanks the Ministerio de Economía y Competitividad (former Ministerio de Ciencia e Innovación) of Spain for a predoctoral (FPI) scholarship.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Cation Gating and Relocation during the Highly Selective Trapdoor Adsorption of CO2 on Univalent Cation Forms of Zeolite Rho

  • Lozinska, Magdalena M.
  • Mowat, John P. S.
  • Wright, Paul A.
  • Thompson, Stephen P.
  • Jorda Moret, Jose Luis|||0000-0002-0304-5680
  • Palomino Roca, Miguel|||0000-0003-2983-1038
  • Valencia Valencia, Susana|||0000-0001-7160-2795
  • Rey Garcia, Fernando|||0000-0003-3227-5669
Adsorption of CO2 and CH4 has been measured on the Na-, K-, and Cs-forms of zeolite Rho (0 9 bar; 283 333 K). Although CH4 is excluded, CO2 is readily taken up, although the uptake at low pressures decreases strongly, in the order Na+ > K+ > Cs+. Structural studies by powder X-ray diffraction (PXRD) suggest that cations in intercage window sites block CH4 adsorption; however, in the presence of CO2, the cations can move enough to permit adsorption (several angstroms). Determination of time-averaged cation positions during CO2 adsorption at 298 K by Rietveld refinement against PXRD data shows that (i) in Na-Rho, there is a small relaxation of Na+ cations within single eight-ring (S8R) sites, (ii) in Cs-Rho, D8R cations move to S8R sites (remaining within windows) and two phases of Cs-Rho (I4&#773;3m, Im3&#773;m) are present over a wide pressure range, and (iii) in K-Rho, there is relocation of some K+ cations from window sites to cage sites and two phases coexist, each with I4&#773;3m symmetry, over the pressure range of 0 1 bar. The final cation distributions at high PCO2 are similar for Na-, K-, and Cs-Rho, and adsorption in each case is only possible by trapdoor -type cation gating. Complementary studies on K-chabazite (Si/Al = 3) also show changes in time-averaged cation location during CO2 adsorption., The authors thank the EPSRC for financial support to M.M.L and PAW. (No. EP/G062129/1, Innovative Gas Separations for Carbon Capture and postgraduate awards for J.P.S.M. and M.M.L.), and F.R., S.V., M.P., and J.L.J. thank the Spanish Government (Nos. MAT2012-38567-C02-01 and CTQ2010-17988/PPQ Consolider Ingenio No. 2010-Multicat CSD-2009-00050 and Severo Ochoa No. SEV-2012-0267). We thank Professor Chiu C. Tang and Claire Murray for assistance at the I-II Beam line at the Diamond Light Source (DLS) and DLS for beamtime (Award No. EE9027).